Draw the block diagram of regulated power supply.

Draw the block diagram of regulated power supply.
by

1 Answer

Answer :

Block diagram of regulated power supply:

image

by

Related questions

Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Description : Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Last Answer : During positive half-cycle of input, the secondary voltage VAB is positive, so diodes D1 and D2 forward biased and D3 and D4 reverse biased. The load current flows from terminal A ... smooth DC voltage appears across the load. The input and output waveforms are shown in the figure.

Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Description : Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Last Answer : 1. A step down transformer 2. A rectifier 3. A filter 4. A regulator Operation of Regulated Power Supply:- Step Down Transformer:- A step down transformer will ... regulator. A regulator will maintain the output constant even when changes at the input or any other changes occur.

Draw the output characteristics of BJT in CE configuration and label various regions on it.

Description : Draw the output characteristics of BJT in CE configuration and label various regions on it.

Last Answer :  output characteristics of BJT in CE configuration 

Draw: (i) Input characteristics of transistor in CE mode. (ii) Output characteristics of transistor in CE mode and show different regions on it.

Description : Draw: (i) Input characteristics of transistor in CE mode. (ii) Output characteristics of transistor in CE mode and show different regions on it.

Last Answer : (i) Input characteristics of transistor in CE mode.   (ii) Output characteristics of transistor in CE mode and show different regions on it.  

Draw and explain: bridge rectifier with shunt capacitor filter.

Description : Draw and explain: bridge rectifier with shunt capacitor filter.

Last Answer : Operation of bridge rectifier with capacitor filter is explained in different intervals with the help of the following wave form. Operation in interval at 0 to A: ... filter is very close to theideal dc voltage waveform as most of the ripple is removed from rectified output.

Explain ideal voltage source with suitable diagram.

Description : Explain ideal voltage source with suitable diagram.

Last Answer : A voltage source is a two terminal device which can maintain a fixed voltage. An ideal voltage source can maintain the fixed voltage independent of the load resistance or the output current. ... the terminal voltage remains constant equal to V volts without load (RL = ∞) or with load

Sketch block diagram of D.C. regulated power supply. State functions of each block.

Description : Sketch block diagram of D.C. regulated power supply. State functions of each block.

Last Answer : There are four basic blocks of a d.c. regulated power supply. They are 1) Step down transformer 2) Rectifier 3) Filter 4) Voltage Regulator.  Functions of each block ... circuit which provides constant dc output voltage irrespective of changes in load current or changes in input voltage. 

Explain the operation of transistor as a switch and as an amplifier, with neat circuit diagrams.

Description : Explain the operation of transistor as a switch and as an amplifier, with neat circuit diagrams. 

Last Answer : Explanation of transistor as a switch: The transistor can be used for two types of application viz. amplification and switching. For the amplification, transistor is biased in its active region. ... results in a large output voltage, which shows that the transistor works as an amplifier.

List any 4 advantages and any 4 disadvantages of Integrated circuits.

Description : List any 4 advantages and any 4 disadvantages of Integrated circuits.

Last Answer : Advantages of Integrated circuits:- 1. Extremely small size. 2. Very small weight . 3. Very low cost . 4. More reliable . 5. Lower power consumption . 6. Easy replacement ... achieved.  9.Large value of saturation resistance of transistors. 10.Voltage dependence of resistor and capacitors.

State the applications of BJT.

Description : State the applications of BJT.

Last Answer : Applications of BJT: 1. As a switch 2. As an amplifier 3. As a multivibrator 4. As a oscillator 5. As a timer circuit 6. As a Logic circuits 7. Delay circuits

Define filter and state it’s types.

Description : Define filter and state it’s types.

Last Answer : A filter circuit may be defined as a circuit, which removes (or minimizes)the unwanted a.c. component of the rectifier output and allows only the d.c. component to reach the load. Types of filters 1) ... 2) Choke input filter(series inductor filter) 3) LC filter 4) π Filter 5) RC filter

List different types of resistors and capacitors.

Description : List different types of resistors and capacitors.

Last Answer : Types of Resistors: 1. Carbon Composition resistor 2. Thin film resistor 3. Thick film resistor 4. Wire wound resistor 5. Thermistor 6. LDR 7. Photo resistor Types of capacitors: 1 ... capacitor 2. Variable capacitor 3. Air ganged capacitor 4. PVC ganged capacitor 5. Trimmer capacitor

Explain statically induced EMF and Dynamically induced EMF with neat diagrams.

Description : Explain statically induced EMF and Dynamically induced EMF with neat diagrams.

Last Answer : Statically Induced EMF:- When changing magnetic field links with a stationary coil an emf is induced. This emf is called statically induced emf. Statically induced EMF is of two types: Self-induced ... cuts the field and an emf is induced. This emf is called dynamically induced emf.    

Explain the working of auto-transformer and state any two advantages of it.

Description : Explain the working of auto-transformer and state any two advantages of it. 

Last Answer : Working of auto transformer :-It is a transformer with one winding only, part of this being common to both primary and secondary. In this transformer the primary and secondary are not electrically ... are less, so the efficiency of auto transformer is higher than that of two winding transformer.

Define transformation ratio of a transformer.

Description : Define transformation ratio of a transformer.

Last Answer : Transformation Ratio (K) of a transformer: It is the ratio of secondary number of turns to primary number of turns. (OR) It is the ratio of secondary voltage to primary voltage. (OR ) It is the ratio of primary current to secondary current. OR

Define FHP motor and list various types.

Description : Define FHP motor and list various types.

Last Answer : Any motor rated less than one horse power may be called as fractional horse power motors(FHP) various types of FHP motors are: 1.Split phase induction motor 2. Capacitor start induction motor 3. Capacitor start capacitor run induction motor 4. Shaded pole induction motor. 

Write the relation between RMS value and Average value.

Description : Write the relation between RMS value and Average value.

Last Answer : The ratio of RMS value to average value is called the form factor of an alternating quantity.

Define (i) Permeability (ii) Reluctance.

Description : Define (i) Permeability (ii) Reluctance.

Last Answer : Permeability: The capability of the magnetic material to conduct the magnetic flux is known as permeability (OR) It is defined as ratio of magnetic flux density B in a medium to the magnetic flux intensity ... as the property of a material due to which it opposes the creation of magnetic flux in it.

Define EMF and state its unit.

Description : Define EMF and state its unit.

Last Answer : Electromotive force(EMF): A potential difference generated by a source of electrical energy across its terminals which tends to produce an electric current in a circuit is called electromotive force. Unit of EMF is Volt

State the need for filters and list the different types of filters.

Description : State the need for filters and list the different types of filters.

Last Answer : Need for filters 1) Output of all rectifiers is pulsating dc voltage and most of citcuits which work on dc requires pure dc voltage. 2) So in order to get pure dc waveform, filters are connected at the ... 2) Choke input filter(series inductor filter) 3) LC filter 4) π Filter 5) RC filter

List the different transistor configurations.

Description : List the different transistor configurations.

Last Answer : The three different transistor configurations are, 1. Common emitter configuration(CE) 2. Common base configuration(CB) 3. Common collector configuration(CC)

State why transistor is called as a bipolar device.

Description : State why transistor is called as a bipolar device.

Last Answer : In case of transistor (BJT), the current conduction takes place due to both electrons and holes, ie, due to both positive as well as negative polarity charge carriers. Therefore transistor is called a bipolar device. 

List any two applications of LED.

Description : List any two applications of LED.

Last Answer : 1) LEDs are used in 7 segment display and dot matrix display. 2) They are used in opto couplers. 3) They are used for indicating power ON/OFF conditions. 4) They are used in infrared remote controls. 5) They are used as indicators in various electronic circuits.

Define passive components and classify them.

Description : Define passive components and classify them.

Last Answer : Passive components: The components which by themselves are not capable of amplifying (or processing) electrical signals are known as passive components. They require external energy source for their functioning. These are bidirectional devices.  Classification: Resistors, Capacitors, Inductors etc.

Compare analog and digital ICs.

Description : Compare analog and digital ICs.

Last Answer : Sr. No. Analog ICs Digital ICs  1 Analog ICs accept and output analog data through its pins. Digital ICs deal with only logic data inputs and outputs.  2 Almost every ... IC for dedicated application. Works with TTL logic level and works in voltage range of 0-5V only.

Compare autotransformer with two winding transformer.

Description : Compare autotransformer with two winding transformer.

Last Answer : Two winding transformer Auto transformer 1.It has two separate windings : a) primary, b)secondary.  1. An auto transformer has single winding which acts both as primary and secondary ... varied. 3. They find application as boosters in AC feeders to increase the voltage levels.

Define: (i) Efficiency (ii) Voltage regulation of transformer.

Description : Define: (i) Efficiency (ii) Voltage regulation of transformer.

Last Answer : i) Efficiency : It is the ratio of output power to the input power of the transformer.It is denoted by η. ii) Voltage Regulation of transformer: The ratio of the change in Secondary Terminal ... So where, VNL = No Load Secondary voltage VFL = Full load secondary voltage

State Faraday's first and second law of electromagnetic induction.

Description : State Faraday's first and second law of electromagnetic induction.

Last Answer : i)Faraday's First Law: Whenever a conductor cuts the magnetic lines of force or is cut by the magnetic lines of force or flux linking with conductor changes, an emf is induced in the conductor.  ... Law: The magnitude of induced emf is directly proportional to the rate of change of flux.

Write emf equation of a transformer.

Description : Write emf equation of a transformer.

Last Answer : E.M.F equation of transformer is given by where Фm= Maximum value of ac flux linking with primary and secondary winding. f = frequency of applied ac signal N= number of turns on primary or ... in primary = E1=4.44 Фm f N1volts  Voltage induced in primary = E2=4.44 Фm f N2volts

State the types of single phase induction motors.

Description : State the types of single phase induction motors.

Last Answer : The types of single phase induction motors are: i) Resistance split phase induction motor. ii) Capacitor split phase inductor motor. a. Capacitor start induction run motor b. permanent capacitor motor c. capacitor start capacitor run induction motor iii) Shaded pole induction motor.

State the working principle of I ø transformer.

Description : State the working principle of I ø transformer.

Last Answer : Working principle of transformer : Transformer works on the principle of mutual electromagnetic induction. When AC voltage is applied to the primary winding of a transformer it causes ac current to flow ... in the secondary winding. The current flows in the secondary circuit if load is connected.

Define: (i) Inductive reactance (ii) Impedance.

Description : Define: (i) Inductive reactance (ii) Impedance.

Last Answer : i) Inductive reactance: Inductive reactance is the opposition offered by an inductor to alternating current . It is denoted by XL and given by XL = 2πf LΩ = ωL Ω ii)Impedance: It is the total opposition offered to flow of AC current in an AC circuit. It is denoted by Z and the unit is ohm. 

With the help of waveforms and phasor diagrams, show the phase relationship between voltage and current in pure inductive circuit.

Description : With the help of waveforms and phasor diagrams, show the phase relationship between voltage and current in pure inductive circuit.

Last Answer : Phasor Diagram:  

List the types of induced emf.

Description : List the types of induced emf.

Last Answer : The types of induced emf are : i) Statically induced emf , ii) Dynamically induced emf

Define: (i) Electromagnetism (ii) Magnetic flux.

Description : Define: (i) Electromagnetism (ii) Magnetic flux.

Last Answer : i)Electromagnetism : It is the magnetism generated by electricity. OR  It is defined as the phenomenon associated with electric and magnetic fields and their interactions with each other. ii) Magnetic flux : The total number of magnetic lines of force in a magnetic field is called magnetic flux.

Draw the block diagram for PLC power supply and explain the function of each block.

Description : Draw the block diagram for PLC power supply and explain the function of each block.

Last Answer : PLC power supply generates the required dc voltage levels for operation of the internal circuit of PLC. It is a switched mode power supply which accepts wide range of AC/ DC input ... of power failure from AC input, Battery backup becomes active and prevents accidental shut down of PLC

Sketch block diagram of an unregulated power supply and explain function of each block.

Description : Sketch block diagram of an unregulated power supply and explain function of each block.

Last Answer : Block diagram of regulated DC power supply:-  Explanation 1)Transformer 2) Rectifier 3) Filter 4) Voltage regulator. 1. Transformer:- Transformer can be step up ... a voltage regulator. Output of the regulator circuit will be constant voltage under all operating circumstances.

Draw the block diagram of satellite sub-system and explain power subsystem.

Description : Draw the block diagram of satellite sub-system and explain power subsystem.

Last Answer : POWER SUBSYSTEM- This system provides the necessary DC power to the satellite. All communication satellites derive their electrical power from solar cells. There is also a battery backup facility used during ... . to d.c. converter is used to raise the level of low voltages to high voltage.

Draw pin diagram of ATX power supply. Give specifications of each pin.

Description : Draw pin diagram of ATX power supply. Give specifications of each pin.

Last Answer : -12V Used in some types of serial port circuits -5V Used for floppy controllers 0V Ground +3.3V Used in many of the new CPUs, system memory, AGP video cards Power Good Signal (PW-OK) The computer ... special circuits even when SMPS is off PS-ON is an input to SMPS only when the signal is low.

The device labeled 'REG SW' in the illustration is used to ___________. EL-0003 A. shift from the automatic voltage regulator to the manual voltage regulator B. shift the governor control from manual to automatic/zero droop C. enable the operator to read the field voltage on device 'REG ADJ' or device 'MAN ADJ' D. supply regulated control power to the switchboard

Description : The device labeled 'REG SW' in the illustration is used to ___________. EL-0003 A. shift from the automatic voltage regulator to the manual voltage regulator B. shift the governor control from manual to ... device 'REG ADJ' or device 'MAN ADJ' D. supply regulated control power to the switchboard

Last Answer : Answer: A

The +5 volt regulated power supply shown in the illustration is fed directly from the _______________. EL-0094 A. 115 volt AC bus B. Annunciator Module C. +24 volt supply D. Annunciator Controller

Description : The +5 volt regulated power supply shown in the illustration is fed directly from the _______________. EL-0094 A. 115 volt AC bus B. Annunciator Module C. +24 volt supply D. Annunciator Controller

Last Answer : Answer: C

How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Description : How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Last Answer : C. Use of regulated power supply

State any four applications of regulated DC power supply.

Description : State any four applications of regulated DC power supply.

Last Answer : * Amplifiers * Mobile Phone power adaptors * Regulated power supplies in appliances * Various oscillators

What is need of regulated power supply?

Description : What is need of regulated power supply?

Last Answer : A regulated power supply is used to ensure that the output remains constant even if the input changes. But sometimes main supply voltage, load, and surrounding temperature keep changing and altering the ... power supply is needed that will accept an AC input and give a constant DC output.

Draw the basic block diagram of digital meter and explain the function of each block.

Description : Draw the basic block diagram of digital meter and explain the function of each block. 

Last Answer : Alternator: It reduces the unknown voltage to a small value. Because the reference voltage is very less and the unknown voltage is maximum. A/D converter: It converts the analog signal from ... and display: It decodes the binary code to decimal form and gives a visual display of it. 

Draw block diagram of digital frequency meter in time mode and describe its operation.

Description : Draw block diagram of digital frequency meter in time mode and describe its operation.

Last Answer : OR Operation: The input signal is amplified and converted to a square wave by a Schmitt Trigger circuit. In this diagram the square wave is differentiated and clipped to ... thereby closing it. The decimal counter and display unit output correspond to the number of input pulses. 

Draw block diagram of DMM. State its advantages.

Description : Draw block diagram of DMM. State its advantages.

Last Answer : Advantages of DMM: 1. DMM provides numerical readouts that eliminate observational errors. Thus providing better readability. 2. DMM offers better accuracy and versatility as compared to ... memory devices for further computations. 5. The decreased size of DMM increases the portability

What is LCR meter? Draw digital LCR –Q meter block diagram.

Description : What is LCR meter? Draw digital LCR –Q meter block diagram.

Last Answer : An LCR meter is a type of electronic test equipment used to measure the inductance (L), capacitance (C), and resistance (R) of an electronic component. Block diagram digital LCR –Q meter  

Draw block diagram of distortion factor meter and explain its operation.

Description : Draw block diagram of distortion factor meter and explain its operation.

Last Answer : Block Diagram Operation This meter consist following four sections 1. Impedance converter along with input circuit 2. Rejection amplifier 3. Metering circuit 4. Power circuit 1. ... of the total input voltage. 4. The power supply unit provides the supply for proper operation 

Draw block diagram of spectrum analyser, State applications of spectrum analyser.

Description : Draw block diagram of spectrum analyser, State applications of spectrum analyser.

Last Answer : Block Diagram: Applications: 1. Spectrum analyzer is a very important item of test equipment for someone designing or repairing electronic equipment that uses radio frequency signals. 2. Its ... of the dominant frequency within a signal 8. Used to measure the properties of RF devices