The co-efficient of coupling of two coils depends on

by

1 Answer

Answer :

The co-efficient of coupling of two coils depends on Physical location of the coils.

by

Related questions

The coefficient of coupling between two coils is 0.45. The first coil has an inductance of 75 mH and the second...

Description : The coefficient of coupling between two coils is 0.45. The first coil has an inductance of 75 mH and the second coil has an inductance of 105 mH. What is the mutual inductance between the coils?  (1) 3.54 mH (2) 7.88 mH (3) 39.9 mH (4) 189.3 mH

Last Answer : The coefficient of coupling between two coils is 0.45. The first coil has an inductance of 75 mH and the second coil has an inductance of 105 mH. 39.9 mH is the mutual inductance between the coils.

The coefficient of coupling between two air core coils depends on

Description : The coefficient of coupling between two air core coils depends on   (A) mutual inductance between two coils only (B) self inductances of the two coils only (C) mutual inductance and self inductances of the two coils (D) none

Last Answer : The coefficient of coupling between two air core coils depends on mutual inductance and self inductances of the two coils 

In case of hydraulically smooth pipe, the resistance to flow depends only on the Reynolds number, whereas for a hydraulically rough pipe, the resistance to flow is governed by the relative roughness. Two pipes are said to have the same hydraulic roughness, when they have equal values of (A) Relative roughness (B) Absolute roughness (C) Friction co-efficient for flows at equal Reynold number (D) All (A), (B) & (C)

Description : In case of hydraulically smooth pipe, the resistance to flow depends only on the Reynolds number, whereas for a hydraulically rough pipe, the resistance to flow is governed by the relative roughness. Two pipes are said ... co-efficient for flows at equal Reynold number (D) All (A), (B) & (C)

Last Answer : (C) Friction co-efficient for flows at equal Reynold number

A block of weight 20 kg slides with an initial velocity of 2 m sec down an inclined plane on to a spring of stiffness 10 kg/cm. If the co--efficient of friction is 0.2, angle ? = 30 the ratio of maximum compession of spring, neglecting friction to that while considering friction would be a.More than one b.One c.Less than one d.Depends on the stiffness of spring e.None of the above

Description : A block of weight 20 kg slides with an initial velocity of 2 m sec down an inclined plane on to a spring of stiffness 10 kg/cm. If the co--efficient of friction is 0.2, angle ? = 30 the ratio of ... be a.More than one b.One c.Less than one d.Depends on the stiffness of spring e.None of the above

Last Answer : a. More than one

For a sphere falling in the constant drag co-efficient regime, its terminal velocity depends on its diameter (D) as (A) d (B) √d (C) d 2 (D) 1/d

Description : For a sphere falling in the constant drag co-efficient regime, its terminal velocity depends on its diameter (D) as (A) d (B) √d (C) d 2 (D) 1/d

Last Answer : (C) d

Diffusion co-efficient generally depends upon the temperature, pressure & the nature of the components of the system. Its dimension is not the same as that of the (A) Mass transfer co-efficient (B) Thermal diffusivity (C) Kinematic viscosity (D) Volumetric diffusivity

Description : Diffusion co-efficient generally depends upon the temperature, pressure & the nature of the components of the system. Its dimension is not the same as that of the (A) Mass transfer co-efficient (B) Thermal diffusivity (C) Kinematic viscosity (D) Volumetric diffusivity

Last Answer : (A) Mass transfer co-efficient

In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Description : In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Last Answer : (B) Decreases

The film co-efficient is decreased due to the presence of non-condensing gases in the vapors. The film co-efficient of superheated vapor as compared to that of saturated vapor is (A) More (B) Less (C) Some (D) Either more or less; depends on the nature of vapor

Description : The film co-efficient is decreased due to the presence of non-condensing gases in the vapors. The film co-efficient of superheated vapor as compared to that of saturated vapor is (A) More (B) Less (C) Some (D) Either more or less; depends on the nature of vapor

Last Answer : (C) Some

The co-efficient of drag and lift for an incompressible fluid depends on the (A) Reynolds number (B) Froude number (C) Mach number (D) All (A), (B) and (C)

Description : The co-efficient of drag and lift for an incompressible fluid depends on the (A) Reynolds number (B) Froude number (C) Mach number (D) All (A), (B) and (C)

Last Answer : (A) Reynolds numbe

The discharge through a Venturimeter depends upon (A) Pressure drop only (B) Its orientation (C) Co-efficient of contraction only (D) None of these

Description : The discharge through a Venturimeter depends upon (A) Pressure drop only (B) Its orientation (C) Co-efficient of contraction only (D) None of these

Last Answer : (A) Pressure drop only

The extent of a reaction is (A) Different for reactants and products (B) Dimensionless (C) Depends on the stoichiometric co-efficient (D) All of the above

Description : The extent of a reaction is (A) Different for reactants and products (B) Dimensionless (C) Depends on the stoichiometric co-efficient (D) All of the above

Last Answer : (D) All of the above

Joule-Thomson co-efficient depends on the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Joule-Thomson co-efficient depends on the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

In a homogeneous solution, the activity co-efficient of a component depends upon the (A) Pressure (B) Composition (C) Temperature (D) All (A), (B) and (C)

Description : In a homogeneous solution, the activity co-efficient of a component depends upon the (A) Pressure (B) Composition (C) Temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Diffusion co-efficient of a metal in a solid solution depends upon its (A) Composition (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Diffusion co-efficient of a metal in a solid solution depends upon its (A) Composition (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Two coils in differential connection have self-inductance of 2 mH and 4 ...

Description : Two coils in differential connection have self-inductance of 2 mH and 4 mH and a mutual inductance of 0.15 mH. The equivalent inductance of the combination is

Last Answer : Two coils in differential connection have self-inductance of 2 mH and 4 mH and a mutual inductance of 0.15 mH. The equivalent inductance of the combination is 5.7 mH.

What is the device, which depends on the action of a movalbe permanent magnet, in aligning itself in the resultant field produced by a fixed permanent magnet or current- carrying coils whose axes are displaced by a fixed angle?

Description : What is the device, which depends on the action of a movalbe permanent magnet, in aligning itself in the resultant field produced by a fixed permanent magnet or current- carrying coils whose axes are displaced by a fixed angle?

Last Answer : moving-magnet instrument

In the illustrated circuit, one advantage of the capacitor coupling over direct coupling is ____________. EL-0048 A. as the frequency decreased the capacitive reactance (Xc) increases B. the amplifier becomes more efficient at lower capacitance. C. the arrangement allows the coupling of the signal while it isolates the biasing of each stage. D. good frequency response.

Description : In the illustrated circuit, one advantage of the capacitor coupling over direct coupling is ____________. EL-0048 A. as the frequency decreased the capacitive reactance (Xc) increases B. the amplifier becomes ... of the signal while it isolates the biasing of each stage. D. good frequency response.

Last Answer : Answer: C

Which of the following device is used for coupling microwave energy?

Description : Which of the following device is used for coupling microwave energy?  A) Resonator B) Waveguide C) Loop D) Antenna

Last Answer : A

R.C coupling is used for - - - amplification

Last Answer :  R.C coupling is used for Voltage amplification

For an amplifier, the coupling method which gives the highest gain is

Last Answer : For an amplifier, the coupling method which gives the highest gain is Transformer coupling.

Transformer coupling introduces which type of distortion?

Description : Transformer coupling introduces which type of distortion?

Last Answer : Transformer coupling introduces Cross over distortion.

The degree of coupling depends

Description : The degree of coupling depends  (A) size of hole (B) location of holes (C) size and location of holes (D) not depend on size or location of hole

Last Answer : The degree of coupling depends location of holes

Co-ordinate coupling is an example of A. Single Degree of Freedom System B. Several Degree of Freedom System C. Two Degree of Freedom System D. None

Description : Co-ordinate coupling is an example of A. Single Degree of Freedom System B. Several Degree of Freedom System C. Two Degree of Freedom System D. None

Last Answer : C. Two Degree of Freedom System

If the driving torque, such as that produced by a diesel engine, creates pulsations when coupled with a synchronous generator operating in parallel; the generator rotor may be periodically pulled ahead or behind its normal position as it rotates. This co A. hunting B. direct coupling C. peaking D. harmonic coupling

Description : If the driving torque, such as that produced by a diesel engine, creates pulsations when coupled with a synchronous generator operating in parallel; the generator rotor may be periodically pulled ahead or behind ... as it rotates. This co A. hunting B. direct coupling C. peaking D. harmonic coupling

Last Answer : Answer: A

The most efficient method of increasing the speed of a 3.75KW d.c. shunt motor would be ...

Description : The most efficient method of increasing the speed of a 3.75KW d.c. shunt motor would be  A) Armature control B) Flux control C) Ward—Leonard D) Tapped—field control

Last Answer :  Flux control 

For same compression ratio and for same heat added  (a) Otto cycle is more efficient than Diesel cycle  (b) Diesel cycle is more efficient than Otto cycle  (c) efficiency depends on other factors  (d) both Otto and Diesel cycles are equally efficient  (e) none of the above.

Description : For same compression ratio and for same heat added  (a) Otto cycle is more efficient than Diesel cycle  (b) Diesel cycle is more efficient than Otto cycle  (c) efficiency depends on other factors  (d) both Otto and Diesel cycles are equally efficient  (e) none of the above.

Last Answer : Answer : a

In a radar system maximum unambiguous range depends on

Description : In a radar system maximum unambiguous range depends on  (A) maximum power of the transmitter (B) pulse repetition frequency (C) width of the transmitted pulse (D) sensitivity of the radar receiver

Last Answer : In a radar system maximum unambiguous range depends on pulse repetition frequency 

In a PCM system of telemetry, the quantization noise depends on:

Description : In a PCM system of telemetry, the quantization noise depends on:  (1) The sampling rate and quantization level (2) The sampling rate only (3) The number of quantization level (4) Information provided is not sufficient

Last Answer : In a PCM system of telemetry, the quantization noise depends on: The number of quantization level.

In any transmitting antenna system, efficiency primarily depends upon

Last Answer : In any transmitting antenna system, efficiency primarily depends upon radiation resistance.

In a transistor leakage current mainly depends on

Last Answer : In a transistor leakage current mainly depends on temperature.

The voltage gain of triode depends on?

Last Answer : The voltage gain of triode depends on plate voltage.

The thermal efficiency of a reversible heat engine operating between two given thermal reservoirs is 0.4. The device is used either as a refrigerator or as a heat pump between the same reservoirs. Then the coefficient of performance as a refrigerator (COP)R and the co-efficient of performance as a heat pump (COP)HP are (A) (COP)R = (COP)HP = 0.6 (B) (COP)R = 2.5; (COP)HP = 1.5 (C) (COP)R = 1.5; (COP)HP = 2.5 (D) (COP)R = (COP)HP = 2.5

Description : The thermal efficiency of a reversible heat engine operating between two given thermal reservoirs is 0.4. The device is used either as a refrigerator or as a heat pump between the same reservoirs. Then the coefficient of performance as a ... )R = 1.5; (COP)HP = 2.5 (D) (COP)R = (COP)HP = 2.5

Last Answer : (C) (COP)R = 1.5; (COP)HP = 2.5

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

__________ involves combining and co -ordinating two or more modes of transportation to take advantage of benefits offered by different types of carriers. A)Intermodal transportation B)Physical distribution C)Containerised movement D)Efficient and effective transportation E)Freight forwarding

Description : __________ involves combining and co -ordinating two or more modes of transportation to take advantage of benefits offered by different types of carriers. A)Intermodal transportation B)Physical distribution C)Containerised movement D)Efficient and effective transportation E)Freight forwarding

Last Answer : A)Intermodal transportation

The importance of the correlation co-efficient lies in the fact that: (A) There is a linear relationship between the correlated variables. (B) It is one of the most valid measure of statistics. (C) It allows one to determine the degree or strength of the association be tween two variables. (D) It is a non-parametric method of statistical analysis.

Description : The importance of the correlation co-efficient lies in the fact that: (A) There is a linear relationship between the correlated variables. (B) It is one of the most valid measure of statistics. ... of the association be tween two variables. (D) It is a non-parametric method of statistical analysis.

Last Answer : (C) It allows one to determine the degree or strength of the association be tween two variables.

A particle moves along a rough plane inclined at 30? to the horizontal. The co-efficient of friction between the particle and the plane is 0.1. Its initial velocity is 15 m/sec. The ratio of the velocity of the particle when it move down the plane to that when it move up the plane would be in the regions a.8 ? 10 b.5 ? 7 c.2 ? 3 d.4 ? 6 e.10 ? 13

Description : A particle moves along a rough plane inclined at 30? to the horizontal. The co-efficient of friction between the particle and the plane is 0.1. Its initial velocity is 15 m/sec. The ratio of the velocity of the particle when it move ... be in the regions a.8 ? 10 b.5 ? 7 c.2 ? 3 d.4 ? 6 e.10 ? 13

Last Answer : b. 5 ? 7

Which one of the following is a nondimensional quantity? (1) Gas constant (2) Strain (3) Co-efficient of viscosity (4) Plank's constant

Description : Which one of the following is a nondimensional quantity? (1) Gas constant (2) Strain (3) Co-efficient of viscosity (4) Plank's constant

Last Answer : (2) Strain Explanation: A dimensionless quantity is simply a quantity that has no units and therefore no dimensions. A ratio between two numbers is a non-dimensional or dimensionless quantity. ... in dimension over original dimension has no dimensional formula. So it is a. dimensionless quantity.

An ideal coolant for a nuclear reactor should (A) Be a good absorber of neutrons (B) Be capable of attaining high temperature, only when it is pressurised (C) Have high density, but low heat transfer co-efficient (D) Be free from radiation damage and non-corrosive

Description : An ideal coolant for a nuclear reactor should (A) Be a good absorber of neutrons (B) Be capable of attaining high temperature, only when it is pressurised (C) Have high density, but low heat transfer co-efficient (D) Be free from radiation damage and non-corrosive

Last Answer : (D) Be free from radiation damage and non-corrosive

Range of compressibility co-efficient of the commercial compressible cake obtained in filtration operation is (A) 0.01 to 0.1(B) 0.1 to 0.3 (C) 0.2 to 0.8 (D) 0.2 to 0.4

Description : Range of compressibility co-efficient of the commercial compressible cake obtained in filtration operation is (A) 0.01 to 0.1 (B) 0.1 to 0.3 (C) 0.2 to 0.8 (D) 0.2 to 0.4

Last Answer : (C) 0.2 to 0.8

Addition of filter aid to the slurry before filtration is done to __________ of the cake. (A) Increase the porosity (B) Increase the compressibility co-efficient (C) Decrease the porosity (D) Decrease the compressibility co-efficient

Description : Addition of filter aid to the slurry before filtration is done to __________ of the cake. (A) Increase the porosity (B) Increase the compressibility co-efficient (C) Decrease the porosity (D) Decrease the compressibility co-efficient

Last Answer : (A) Increase the porosity

Compressibility co-efficient for an absolutely compressible cake is (A) 0 (B) 1 (C) 0 to 1 (D) ∞

Description : Compressibility co-efficient for an absolutely compressible cake is (A) 0 (B) 1 (C) 0 to 1 (D) ∞

Last Answer : (B) 1

. Which of the following relationships between co-efficient of friction (μ) between rock & roll and a (half of the angle of nip) of the particle to be crushed is correct? (A) μ > tan α (B) μ ≥ tan α (C) μ > tan 2α (D) μ ≤ tan α

Description : . Which of the following relationships between co-efficient of friction (μ) between rock & roll and a (half of the angle of nip) of the particle to be crushed is correct? (A) μ > tan α (B) μ ≥ tan α (C) μ > tan 2α (D) μ ≤ tan α

Last Answer : (B) μ ≥ tan α

A steel alloy containing 36% nickel is called __________, which has a zero co-efficient of expansion. (A) Austenitic stainless steel (B) Heat resisting steel (C) Invar (D) High speed steel

Description : A steel alloy containing 36% nickel is called __________, which has a zero co-efficient of expansion. (A) Austenitic stainless steel (B) Heat resisting steel (C) Invar (D) High speed steel

Last Answer : (C) Invar

Which of the following is universally employed as the low expansion metal in the bimetallic thermometer, which is an iron-nickel alloy containing 36% nickel and has very low co-efficient of expansion (1/20th of ordinary metals) ? (A) Invar (B) Constantan (C) Chromel (D) Alumel

Description : Which of the following is universally employed as the low expansion metal in the bimetallic thermometer, which is an iron-nickel alloy containing 36% nickel and has very low co-efficient of expansion (1/20th of ordinary metals) ? (A) Invar (B) Constantan (C) Chromel (D) Alumel

Last Answer : (A) Invar

A bearing metal should not have (A) Enough plasticity (B) Low thermal conductivity (C) Low co-efficient of friction (D) High toughness

Description : A bearing metal should not have (A) Enough plasticity (B) Low thermal conductivity (C) Low co-efficient of friction (D) High toughness

Last Answer : (B) Low thermal conductivity

Babbitt metal used for making bearings should have (A) High co-efficient of friction between journal and bearing (B) Ability to retain lubricant on its surface (C) Low co-efficient of friction between journal and bearing (D) Both (B) & (C)

Description : Babbitt metal used for making bearings should have (A) High co-efficient of friction between journal and bearing (B) Ability to retain lubricant on its surface (C) Low co-efficient of friction between journal and bearing (D) Both (B) & (C)

Last Answer : (A) High co-efficient of friction between journal and bearing

Brass tubes are used in the manufacture of tubes of evaporators used in sugar and salt industries, mainly because of its (A) High co-efficient of thermal expansion (B) Low thermal conductivity (C) High corrosion resistance (D) All (A), (B) and (C)

Description : Brass tubes are used in the manufacture of tubes of evaporators used in sugar and salt industries, mainly because of its (A) High co-efficient of thermal expansion (B) Low thermal conductivity (C) High corrosion resistance (D) All (A), (B) and (C)

Last Answer : (C) High corrosion resistance

Gaseous diffusion co-efficient increases with increase in the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Gaseous diffusion co-efficient increases with increase in the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (B) Temperature

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s