The type of dc generator used for arc welding purposes is a

by

1 Answer

Answer :

The type of dc generator used for arc welding purposes is a Differentially compound generator.

by

Related questions

Which of the following generators is used for DC arc welding application ?

Description :  Which of the following generators is used for DC arc welding application ? (A) Series generator (B) Shunt generator (C) Differential compound generator (D) Over -compound generator

Last Answer : A

A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC+ve polarity, and a ROL:of 180mm per min. What would be the arc energy? a) Insufficient information given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Last Answer : d) 2.0 kJ/mm

The required DC voltage for arc welding is- (1) 6 to 9 V (2) 50 to 60 V (3) 200 to 250 V (4) 90 to 100 V

Description : The required DC voltage for arc welding is- (1) 6 to 9 V (2) 50 to 60 V (3) 200 to 250 V (4) 90 to 100 V

Last Answer : (3) 200 to 250 V

When MMA welding what will be the effect on the weld f the power source was changed from AC to DC-ve? a) None b) Higher deposition rate c) It would slightly increase the depth of penetration d) The arc would become unstable

Description : When MMA welding what will be the effect on the weld f the power source was changed from AC to DC-ve? a) None b) Higher deposition rate c) It would slightly increase the depth of penetration d) The arc would become unstable

Last Answer : b) Higher deposition rate

Arc welding uses following electric supply

Description : Arc welding uses following electric supply (A) ac (B) dc (C) both ac and dc (D) spiral waveform 

Last Answer : both ac and dc

Arc blow is a welding defect which is encountered in _________.

Last Answer : Arc blow is a welding defect which is encountered in arc welding using a.c. current.

What type of arc welding equipment is necessary when participating in arc welding?

Description : What type of arc welding equipment is necessary when participating in arc welding?

Last Answer : The most important equipment you can have is your safety equipment, your gloves, visor and heavy-duty clothing. You have to have some sort of a power source to generate the electricity necessary for arc welding, so I'd say a power source is your most important arc welding equipment.

Which type of welding is generally used in automobile sector? a) Electric arc welding b) Electric resistance welding c) Gas welding d) Forge welding

Description : Which type of welding is generally used in automobile sector? a) Electric arc welding b) Electric resistance welding c) Gas welding d) Forge welding

Last Answer : b) Electric resistance welding

The electric arc welding is a type of ............. welding. (a) forge (b) fusion

Description : The electric arc welding is a type of ............. welding. (a) forge (b) fusion

Last Answer : b) fusion

Argon is used in arc welding because

Description : Argon is used in arc welding because

Last Answer : Argon is used in arc welding because A. low reactivity with metal B. ability to lower the ... of metal C. flammability D. high calorific value

In arc welding, Argon is used because of its - (1) Low reactivity with metal (2) Ability to lower the melting point of the metal (3) High flammability (4) High calorific value

Description : In arc welding, Argon is used because of its - (1) Low reactivity with metal (2) Ability to lower the melting point of the metal (3) High flammability (4) High calorific value

Last Answer : (1) Low reactivity with metal Explanation: In arc welding, Argon is used as a shielding gas because it is chemically inert and forms no compounds. At the high temperatures that welding requires, the ... to brittle welds and instability in the welding arc. So,argon and other inert gases are sprayed.

Projection welding is (i) Electric arc welding (ii) Gas welding (iii)Spot welding (iv) None

Description : Projection welding is (i) Electric arc welding (ii) Gas welding (iii)Spot welding (iv) None

Last Answer : (iv) None

Among gas and electric arc welding, which has the higher rate of heating? a) Gas welding b) Electric arc welding c) Gas welding and electric arc welding have equal rate of heating d) Cannot be determined

Description : Among gas and electric arc welding, which has the higher rate of heating? a) Gas welding b) Electric arc welding c) Gas welding and electric arc welding have equal rate of heating d) Cannot be determined

Last Answer : b) Electric arc welding

Rails in the field are generally welded by using a) Thermit welding b) Gas welding c) Electric arc welding d) Forge welding

Description : Rails in the field are generally welded by using a) Thermit welding b) Gas welding c) Electric arc welding d) Forge welding

Last Answer : a) Thermit welding

Consumable electrodes are used in the __________ welding. (A) Gas (B) Arc (C) Thermit (D) Resistance

Description : Consumable electrodes are used in the __________ welding. (A) Gas (B) Arc (C) Thermit (D) Resistance

Last Answer : (B) Arc

Projection welding & stud welding is categorised as the __________ welding. (A) Pressure (B) Thermit (C) Resistance (D) Arc

Description : Projection welding & stud welding is categorised as the __________ welding. (A) Pressure (B) Thermit (C) Resistance (D) Arc

Last Answer : C) Resistance

Which of the following mainly decides the current to be employed is arc welding? (A) Electrode size (B) Plate thickness (C) Voltage across the arc (D) Welded portion length

Description : Which of the following mainly decides the current to be employed is arc welding? (A) Electrode size (B) Plate thickness (C) Voltage across the arc (D) Welded portion length

Last Answer : (A) Electrode size

Coating provided on the electrodes used in the arc welding is not expected to (A) Add alloying elements (B) Prevent electrode from contamination (C) Stabilise the arc (D) Provide protective atmosphere to weld

Description : Coating provided on the electrodes used in the arc welding is not expected to (A) Add alloying elements (B) Prevent electrode from contamination (C) Stabilise the arc (D) Provide protective atmosphere to weld

Last Answer : (B) Prevent electrode from contamination

Cold cracking in the heat affected zone of a high strength steel weld can take place because of the (A) Retained austenite (B) Martensite formation (C) Relatively high sulphur content in the base metal (D) Sufficient hydrogen present in the welding arc

Description : Cold cracking in the heat affected zone of a high strength steel weld can take place because of the (A) Retained austenite (B) Martensite formation (C) Relatively high sulphur content in the base metal (D) Sufficient hydrogen present in the welding arc

Last Answer : (B) Martensite formation

Stainless steel is welded using (A) Oxy-acetylene flame (B) Oxy-hydrogen flame (C) Arc welding (D) Inert gas arc welding

Description : Stainless steel is welded using (A) Oxy-acetylene flame (B) Oxy-hydrogen flame (C) Arc welding (D) Inert gas arc welding

Last Answer : (D) Inert gas arc welding

What is a typical ARC voltage setting when welding with the TIG (GTAW) process? a) 18-20V b) 24-26V c) 10-12V d) 70-90V

Description : What is a typical ARC voltage setting when welding with the TIG (GTAW) process? a) 18-20V b) 24-26V c) 10-12V d) 70-90V

Last Answer : c) 10-12V

Explain the shielded metal arc welding (SMAW) processes with neat sketch. State its two advantages and disadvantages.

Description : Explain the shielded metal arc welding (SMAW) processes with neat sketch. State its two advantages and disadvantages.

Last Answer : Working  : Shielded metal arc welding uses a metallic consumable electrode of a proper composition for generating arc between itself and the parent work piece. The molten electrode metal fills the weld ... . 2. Weld may contain slag inclusions 3. Fumes make difficult the process control.

List common equipments used for arc welding process.

Description : List common equipments used for arc welding process.

Last Answer : 1. A.C. or D.C. machine 2. Electrode (bare or coated) 3. Electrode Holder 4. Cables and its connectors 5. Chipping Hammer 6. Earthing Clamps 7. Wire-brush 8. Helmet 9. Safety Goggles 10. Hand Gloves 11. Apron Sleeves etc.

Describe the working principle of Arc Welding.

Description : Describe the working principle of Arc Welding.

Last Answer : Arc welding is the most extensively employed method of joining metal parts. Here the source of heat is an electric arc. The arc column is generated between an anode which is the positive pole of D.C. ... also melted and is transferred in to the metal in the form of globules of molten metal.  

Compare resistance welding and arc welding.

Description : Compare resistance welding and arc welding. 

Last Answer : Sr. No Resistance Welding Arc Welding 1 It is plastic welding It is fusion welding. 2 Arc is produced by heat due to resistance of flow of current by work and by application ... 8 Less skilled operator can do the job. More skilled operator is required to the job

Draw a schematic of a set up of shielded metal arc welding.

Description : Draw a schematic of a set up of shielded metal arc welding. 

Last Answer : Fig. Shielded metal arc welding set-up

In arc welding, Argon is used because of its (1) Low reactivity with metal (2) Ability to lower the melting point of the metal (3) High flammability (4) High calorific value

Description : In arc welding, Argon is used because of its (1) Low reactivity with metal (2) Ability to lower the melting point of the metal (3) High flammability (4) High calorific value

Last Answer :  Low reactivity with metal

Compare between Resistance welding and Arc welding on any six points.

Description : Compare between Resistance welding and Arc welding on any six points.

Last Answer : Sr.No Parameters Resistance Welding Arc Welding 1 Type of welding Plastic/Pressure/Non-fusion welding Fusion/Non pressure welding 2 Principle of heat developed Heat ... It is suitable for mass production It is suitable for heavy job, maintenance and repair work

The commonly used gases in tungsten arc welding are

Description : The commonly used gases in tungsten arc welding are 1.Hydrogen and oxygen 2.Hydrogen and organ 3.Hydrogen and helium 4.Helium and argon

Last Answer : The commonly used gases in tungsten arc welding are Helium and argon

For arc welding current range is usually

Description : For arc welding current range is usually  (1) 10 to 15 A (2) 30 to 40 A (3) 50 to 100 A (4) 100 to 350 A

Last Answer : For arc welding current range is usually 100 to 350 A

Identify the correct combination of respective Electric arc welding and Electric resistance welding methods :

Description : Identify the correct combination of respective Electric arc welding and Electric resistance welding methods :  (A) Butt welding and Seam welding  (B) Hydrogen shielding and Projection welding  (C) Seam welding and Coated electrode welding  (D) Coated electrode welding and Hydrogen shielding

Last Answer : Identify the correct combination of respective Electric arc welding and Electric resistance welding methods :  (A) Butt welding and Seam welding  (B) Hydrogen shielding and Projection welding  ... Seam welding and Coated electrode welding  (D) Coated electrode welding and Hydrogen shielding

The supply for arc welding is :

Description : The supply for arc welding is : 

Last Answer : The supply for arc welding is : Low voltage, high current ac or dc voltage

Low purity oxygen is used for(A) L.D. steel making(B) Cutting and welding of metals(C) Medicinal purposes(D) Chemical oxidation processes

Description : Low purity oxygen is used for (A) L.D. steel making (B) Cutting and welding of metals (C) Medicinal purposes (D) Chemical oxidation processes

Last Answer : (D) Chemical oxidation processes

99.5% purity oxygen is used in (A) Cutting and welding by oxy-acetylene flame (B) Hospitals for medicinal purposes (C) Gas masks and artificial breathing apparatus (D) All (A), (B), and (C)

Description : 99.5% purity oxygen is used in (A) Cutting and welding by oxy-acetylene flame (B) Hospitals for medicinal purposes (C) Gas masks and artificial breathing apparatus (D) All (A), (B), and (C)

Last Answer : (D) All (A), (B), and (C)

Oxygen cylinders used for autogenous (cutting/welding) purposes are (A) Seamless & made of steel (B) Heat treated before use (C) Made by sand casting (D) Welded steel cylinders

Description : Oxygen cylinders used for autogenous (cutting/welding) purposes are (A) Seamless & made of steel (B) Heat treated before use (C) Made by sand casting (D) Welded steel cylinders

Last Answer : Option A

In an AC generator, direct current from a separate source is passed through the windings of the rotor _____________. A. by means of slip rings and brushes B. by means of a commutator C. by means of rotating bar magnet D. to minimize the danger of arc over

Description : In an AC generator, direct current from a separate source is passed through the windings of the rotor _____________. A. by means of slip rings and brushes B. by means of a commutator C. by means of rotating bar magnet D. to minimize the danger of arc over

Last Answer : Answer: A

How arc is quenched in Generator Field Breaker?

Description : How arc is quenched in Generator Field Breaker?

Last Answer : By magnetic blow out coils, arc is elongated very fastly, so resistance of arc increases, soon becoming unstable and quenched by arc chutes. 

When using multiple SAW arc systems (twin wires etc), the arcs often have different polarities or use all AC rather than DC polarity, this is to? a) Prevent arc blow between arcs b) To maximize productivity c) To even out the power factor on the mains supply d) Make it easier to initiate the arc

Description : When using multiple SAW arc systems (twin wires etc), the arcs often have different polarities or use all AC rather than DC polarity, this is to? a) Prevent arc blow between arcs b) To maximize productivity c) To even out the power factor on the mains supply d) Make it easier to initiate the arc

Last Answer : a) Prevent arc blow between arcs

Compare the AC and DC Arc lamps.

Description : Compare the AC and DC Arc lamps.

Last Answer : AC Arc Lamp DC Arc Lamp Cross section area of electrode is same Cross section area of electrode is positive rod is twice that of negative rod Series inductor is used for stability ... supply is used for DC arc lamp Luminous efficiency is less Luminous efficiency is high

Give the classification of DC generator based on their winding connections.

Description : Give the classification of DC generator based on their winding connections. 

Last Answer : 1) D.C Shunt Generator 2) D.C Series Generator 3) D.C Compound Generator: i) Cumulative compound generator ii) Differential compound Generator 

State principle of operation of DC generator.

Description : State principle of operation of DC generator.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Describe with neat diagram working of DC tacho-generator.

Description : Describe with neat diagram working of DC tacho-generator. 

Last Answer : Explanation : The D.C Tachogenerators is a type of electrical type's tachogenerators which can also be used for speed measurement.The D.C tachogenerator is shown in above figure. The ... to collect current from commutator and make it available to external circuitry of the d.c tachogenerator.

The terminal characteristics of a dc generator suitable for electric welders is

Description : The terminal characteristics of a dc generator suitable for electric welders is (A) separately excited generator (B) shunt generator (C) series generator (D) differentially compounded generator

Last Answer : The terminal characteristics of a dc generator suitable for electric welders is differentially compounded generator

An 8 pole lap wound DC shunt generator is supplying 295A to a load. The field current of the generator is 5A....

Description :  An 8 pole lap wound DC shunt generator is supplying 295A to a load. The field current of the generator is 5A. The current per parallel path is: -  a) 300A b) 200A c) 150A d) 37.5A

Last Answer :  An 8 pole lap wound DC shunt generator is supplying 295A to a load. The field current of the generator is 5A. The current per parallel path is: - 37.5A

The generator which gives dc supply to the rotor is called:

Description : The generator which gives dc supply to the rotor is called:  (1) Converter (2) Exciter (3) Inverter (4) Rectifier

Last Answer : The generator which gives dc supply to the rotor is called: Exciter.

Welding generator will have?

Last Answer : Welding generator will have lap winding.

What do we use for welding on ships? AC or DC?

Description : What do we use for welding on ships? AC or DC?

Last Answer : Ask E/O on your ship.

Compare DC and AC welding on any four points.

Description : Compare DC and AC welding on any four points.

Last Answer : Points DC Welding AC Welding Supply equipment used  DC differential Compound Generator, or Rectifier Welding Transformer Heating Effect Uniform Not Uniform Temperature Obtain ... High, 85% Application Carbon Arc Welding Resistance Welding , Metal Arc Welding

4. The essential difference between an AC generator and a DC generator is that -Physics-10

Description : 4. The essential difference between an AC generator and a DC generator is that -Physics-10

Last Answer : AC generator has slip rings while the DC generator has a commutator. AC generators have two rings known as the slip rings while DC generators have two half rings known as the commutator. This is main difference between AC generator and DC generator.