In which of the following directions, the strength of timber is maximum a) Parallel to grains* b) 45 degree to grains c) Perpendicular to grains d) same in all directions

In which of the following directions, the strength of timber is maximum a) Parallel to grains*
b) 45 degree to grains
c) Perpendicular to grains
d) same in all directions
by

1 Answer

Answer :

a) Parallel to grains*
by

Related questions

In which of the following directions, the strength of timber is maximum? (A) Parallel to grains (B) 45° to grains (C) Perpendicular to grains (D) Same in all directions

Description : In which of the following directions, the strength of timber is maximum? (A) Parallel to grains (B) 45° to grains (C) Perpendicular to grains (D) Same in all directions

Last Answer : Answer: Option A

Chandigarh is a city which has roads generally parallel or perpendicular to each other. The ideal water supply system in such a city should be a. Dead and system b. Grid Iron system* c. Ring system d. Any of them

Description : Chandigarh is a city which has roads generally parallel or perpendicular to each other. The ideal water supply system in such a city should be a. Dead and system b. Grid Iron system* c. Ring system d. Any of them

Last Answer : b. Grid Iron system*

In Fraunhofer diffraction pattern for single slit, a central maximum is obtained when angle of diffraction q is equal to zero. What it actually indicates? A. All the diffracted rays are parallel and focused by slit at a single point on screen B. All the diffracted rays are perpendicular and focused by slit at a single point on screen C. The rays are diffracted by the slit in all the directions D. The rays are reflected by the slit

Description : In Fraunhofer diffraction pattern for single slit, a central maximum is obtained when angle of diffraction q is equal to zero. What it actually indicates? A. All the diffracted rays are parallel and focused ... are diffracted by the slit in all the directions D. The rays are reflected by the slit

Last Answer : A. All the diffracted rays are parallel and focused by slit at a single point on screen

Pick up the correct statement from the following: Method of sawing timber (A) Tangentially to annual rings, is known as tangential method (B) In four quarters such that each board cuts annual rings at angles not less than 45°, is known as quarter sawing method (C) Cut out of quarter logs, parallel to the medullary rays and perpendicular to annual rings, is known as radial sawing (D) All the above

Description : Pick up the correct statement from the following: Method of sawing timber (A) Tangentially to annual rings, is known as tangential method (B) In four quarters such that each board cuts annual rings ... medullary rays and perpendicular to annual rings, is known as radial sawing (D) All the above

Last Answer : Answer: Option D

Length of bridge timber in BG a) outer to outer of girder plus 305mm b) 2440mm c) whichever is more in a) & b)* d) whichever is less in a) & b)

Description : Length of bridge timber in BG a) outer to outer of girder plus 305mm b) 2440mm c) whichever is more in a) & b)* d) whichever is less in a) & b)

Last Answer : c) whichever is more in a) & b)*

The size of bridge timber required for the standard spans up to 18.3 m a) 250 x 150mm*. b) 250 x 180mm. c) 250 x 240mm d) 250 x 200mm

Description : The size of bridge timber required for the standard spans up to 18.3 m a) 250 x 150mm*. b) 250 x 180mm. c) 250 x 240mm d) 250 x 200mm

Last Answer : a) 250 x 150mm*.

The average coefficient of permeability of natural deposits (A) Parallel to stratification is always greater than that perpendicular to stratification (B) Parallel to stratification is always less than that perpendicular to stratification (C) Is always same in both directions (D) Parallel to stratification may or may not be greater than that perpendicular to stratification

Description : The average coefficient of permeability of natural deposits (A) Parallel to stratification is always greater than that perpendicular to stratification (B) Parallel to stratification is always less ... D) Parallel to stratification may or may not be greater than that perpendicular to stratification

Last Answer : Answer: Option A

The minimum and maximum clearances of check rails at all BG level crossings shall be a) 51 to 57 mm* b) 44 to 48 mm c) 41 to 45 mm d) 55 to 70 mm

Description : The minimum and maximum clearances of check rails at all BG level crossings shall be a) 51 to 57 mm* b) 44 to 48 mm c) 41 to 45 mm d) 55 to 70 mm

Last Answer : a) 51 to 57 mm*

If a material has identical properties in all directions, it is called (a) Elastic (b) Plastic (c) Isotropic (d) Homogeneous

Description : If a material has identical properties in all directions, it is called (a) Elastic (b) Plastic (c) Isotropic (d) Homogeneous

Last Answer : (c) Isotropic

The advantages of electrometric bearings are a) Permits movement of the structure in all directions b) Serves as a shock absorber due to anti-vibration properties of elestomeric c) better dispersion of longitudinal forces to the approaches d) All of the above*

Description : The advantages of electrometric bearings are a) Permits movement of the structure in all directions b) Serves as a shock absorber due to anti-vibration properties of elestomeric c) better dispersion of longitudinal forces to the approaches d) All of the above*

Last Answer : d) All of the above*

Which of the following in theodolite work is imperfect adjustment of the instrument (a) Error due to line of collimation being perpendicular to the horizontal axis (b) Error due to axis not to perpendicular of the vertical axis (c) Error due to imperfect graduation (d) Error due to eccentricity of vernires (e) All of the above*

Description : Which of the following in theodolite work is imperfect adjustment of the instrument (a) Error due to line of collimation being perpendicular to the horizontal axis (b) Error due to axis not to perpendicular ... to imperfect graduation (d) Error due to eccentricity of vernires (e) All of the above*

Last Answer : (e) All of the above*

Angle of crossing of a bridge is the angle between a) C.L. of water course/road to C.L. of track* b) C.L. of water course to C.L. of pier c) C.L. of water course to normal (perpendicular) of C.L. of track d) C.L. of abutment to C.L. of pier

Description : Angle of crossing of a bridge is the angle between a) C.L. of water course/road to C.L. of track* b) C.L. of water course to C.L. of pier c) C.L. of water course to normal (perpendicular) of C.L. of track d) C.L. of abutment to C.L. of pier

Last Answer : a) C.L. of water course/road to C.L. of track*

Skew of a bridge is the angle between a) C.L. of water course to C.L. of track b) C.L. of water course to C.L. of pier c) C.L. of water course/road to normal (perpendicular) of C.L. of track* d) C.L. of abutment to C.L. of pier

Description : Skew of a bridge is the angle between a) C.L. of water course to C.L. of track b) C.L. of water course to C.L. of pier c) C.L. of water course/road to normal (perpendicular) of C.L. of track* d) C.L. of abutment to C.L. of pier

Last Answer : c) C.L. of water course/road to normal (perpendicular) of C.L. of track*

Clear perpendicular distance between inner faces of two rails is a. Gauge of track* b. Inner gauge c. Wheel base d. Wheel gauge

Description : Clear perpendicular distance between inner faces of two rails is a. Gauge of track* b. Inner gauge c. Wheel base d. Wheel gauge

Last Answer : a. Gauge of track*

Maximum curvature permitted on B.G. is (a) 8 degree (b) 10 degree* (c) 12 degree (d) 16 degree

Description : Maximum curvature permitted on B.G. is (a) 8 degree (b) 10 degree* (c) 12 degree (d) 16 degree

Last Answer : (b) 10 degree*

fter storage, strength of cement a) Decreases* b) Increases c) Remains same d) Depends upon the type of cement

Description : fter storage, strength of cement a) Decreases* b) Increases c) Remains same d) Depends upon the type of cement

Last Answer : a) Decreases*

If harmonic motion of same frequency and same phase are superimposed in two perpendicular directions ( x and y) then, the resultant motion will be, A) circle B) An ellipse C) An square D) An rectangle

Description : If harmonic motion of same frequency and same phase are superimposed in two perpendicular directions ( x and y) then, the resultant motion will be, A) circle B) An ellipse C) An square D) An rectangle

Last Answer : C) An square

Last flag man is deputed at which distance from last detonator during protection of welding site . (i) 30 mts (ii) 50 mts (iii) 45 (iv) 60 mts

Description : Last flag man is deputed at which distance from last detonator during protection of welding site . (i) 30 mts (ii) 50 mts (iii) 45 (iv) 60 mts

Last Answer : (iv) 60 mts

Torch is kept at height from top surface of rail head? (i) 30 to 55 mm (ii) 35 to 40 mm (iii) 40 to 45 mm

Description : Torch is kept at height from top surface of rail head? (i) 30 to 55 mm (ii) 35 to 40 mm (iii) 40 to 45 mm

Last Answer : (iii) 40 to 45 mm

What is the speed restriction to be observed for train passing? (i) Necessary speed restriction shall be observed until the grinding operation is over.* (ii) 30KMPH (iii) 45 KMPH (iv) Not required

Description : What is the speed restriction to be observed for train passing? (i) Necessary speed restriction shall be observed until the grinding operation is over.* (ii) 30KMPH (iii) 45 KMPH (iv) Not required

Last Answer : (i) Necessary speed restriction shall be observed until the grinding operation is over.*

The bottom of side drains should be below the formation level by at least------------ a) 45 cm b )30 cm* c) 15 cm d) 60 cm

Description : The bottom of side drains should be below the formation level by at least------------ a) 45 cm b )30 cm* c) 15 cm d) 60 cm

Last Answer : b )30 cm*

Minimum depth of space for wheel flange form rail level in B.G. is …… mm (A) 35 (B) 38* (C) 42 (D) 45

Description : Minimum depth of space for wheel flange form rail level in B.G. is …… mm (A) 35 (B) 38* (C) 42 (D) 45

Last Answer : (B) 38*

.Minimum wing rail clearance opposing nose of crossing on Fan shaped turnout a. 45 mm b. 40 mm c. 41 mm* d. 44 mm

Description : .Minimum wing rail clearance opposing nose of crossing on Fan shaped turnout a. 45 mm b. 40 mm c. 41 mm* d. 44 mm

Last Answer : c. 41 mm*

.Minimum check rail clearance at Level crossing a. 45 mm b. 51 mm* c. 50 mm d. 57 mm

Description : .Minimum check rail clearance at Level crossing a. 45 mm b. 51 mm* c. 50 mm d. 57 mm

Last Answer : b. 51 mm*

If used, in which direction should pinholes be placed? a. parallel to the long axis of the tooth b.parallel to the nearest external surface c. at a 15 degree angle to the long axis of the tooth d. perpendicular to the gingival floor e. directly below and parallel to restored cusp tip

Description : If used, in which direction should pinholes be placed? a. parallel to the long axis of the tooth b.parallel to the nearest external surface c. at a 15 degree angle to the long axis of the tooth d. perpendicular to the gingival floor e. directly below and parallel to restored cusp tip

Last Answer : b.parallel to the nearest external surface

Loading capacity of chain drive system is based on a) Rate of wear b) Ultimate strength of chain material c) None of (a) and (b) d) Both (a) and (b)

Description : Loading capacity of chain drive system is based on a) Rate of wear b) Ultimate strength of chain material c) None of (a) and (b) d) Both (a) and (b)

Last Answer : a) Rate of wear

The approximate ratio between the strength of cement concrete at seven days and 28 days is a) 3/ 4 b) 2/3* c) 1/2 d) 1/3

Description : The approximate ratio between the strength of cement concrete at seven days and 28 days is a) 3/ 4 b) 2/3* c) 1/2 d) 1/3

Last Answer : b) 2/3*

Le Chatelier apparatus is used to determine which of the following properties for cement A) Soundness* b) Initial setting time c) Compressive strength d) Tensile strength

Description : Le Chatelier apparatus is used to determine which of the following properties for cement A) Soundness* b) Initial setting time c) Compressive strength d) Tensile strength

Last Answer : A) Soundness*

he minimum compressive strength of first class brick should be a) 75 kg per centimeter square b) 90 kg per centimeter square c) 100 kg per centimeter square* d) 120 kg per centimeter square

Description : he minimum compressive strength of first class brick should be a) 75 kg per centimeter square b) 90 kg per centimeter square c) 100 kg per centimeter square* d) 120 kg per centimeter square

Last Answer : c) 100 kg per centimeter square*

AA saturated clay is to be tested for shearing strength. Which test should be recommended? a) Direct shear test b) Triaxial shear test c) Vane shear test d) Unconfined compression*

Description : A saturated clay is to be tested for shearing strength. Which test should be recommended? a) Direct shear test b) Triaxial shear test c) Vane shear test d) Unconfined compression*

Last Answer : d) Unconfined compression*

Piping in a soil mass is a) Erosion of subsoil by the high velocities of flow of water through it when such velocities exceed a certain limit* b) Caused due to very low exit gradient c) Due to continuous passage of water through a series of well connected pores d) Due to loss of the strength of cohesion less soil because of upward flow of of water

Description : Piping in a soil mass is a) Erosion of subsoil by the high velocities of flow of water through it when such velocities exceed a certain limit* b) Caused due to very low exit gradient c) ... connected pores d) Due to loss of the strength of cohesion less soil because of upward flow of of water

Last Answer : a) Erosion of subsoil by the high velocities of flow of water through it when such velocities exceed a certain limit*

Quicksand is a) Moist sand containing a small percentage of clay b) Is a condition which generally occurs in coarse sands c) Is a condition in which cohesive properties of soil increase rapidly d) Is a condition in which a cohesion less soil loses its strength because of upward flow of water

Description : Quicksand is a) Moist sand containing a small percentage of clay b) Is a condition which generally occurs in coarse sands c) Is a condition in which cohesive properties of soil increase rapidly d) Is a condition in which a cohesion less soil loses its strength because of upward flow of water

Last Answer : d) Is a condition in which a cohesion less soil loses its strength because of upward flow of water

At the liquid limit a) The soil just begins to crumble when rolled into a thread b) The shearing strength against flowing is negligible c) The shearing strength against flowing is a small but definite* d) The soil will not get fully saturated

Description : At the liquid limit a) The soil just begins to crumble when rolled into a thread b) The shearing strength against flowing is negligible c) The shearing strength against flowing is a small but definite* d) The soil will not get fully saturated

Last Answer : c) The shearing strength against flowing is a small but definite

The side slope of formation in embankment /cutting depends on a) Shearing strength of soil and its angle of repose* b) Angle of repose c) Bearing capacity of the soil d) Optimum moisture content of the soil

Description : The side slope of formation in embankment /cutting depends on a) Shearing strength of soil and its angle of repose* b) Angle of repose c) Bearing capacity of the soil d) Optimum moisture content of the soil

Last Answer : a) Shearing strength of soil and its angle of repose*

Ultrasonic Pulse Velocity test is meant for a) Identifying the integrity of concrete* b) Finding the strength of concrete c) To know the crack in steel structure d) To know the flaw in rail

Description : Ultrasonic Pulse Velocity test is meant for a) Identifying the integrity of concrete* b) Finding the strength of concrete c) To know the crack in steel structure d) To know the flaw in rail

Last Answer : a) Identifying the integrity of concrete*

Rebound hammer is used for a) To find the strength of concrete* b) To form rivet heads c) To break the concrete structures d) None of the above

Description : Rebound hammer is used for a) To find the strength of concrete* b) To form rivet heads c) To break the concrete structures d) None of the above

Last Answer : a) To find the strength of concrete*

The strength of a bridge is termed as MBG loading of 1987. MBG refers to a) Model Broad Gauge b) Modified Budget Grant c) Model Budget grant d) Modified Broad Gauge*

Description : The strength of a bridge is termed as MBG loading of 1987. MBG refers to a) Model Broad Gauge b) Modified Budget Grant c) Model Budget grant d) Modified Broad Gauge*

Last Answer : d) Modified Broad Gauge*

What is the full form UTS of rails a. Ultimate technical Strength b. Ultimate tensile Strength* c. Upper Top surface d. None of above

Description : What is the full form UTS of rails a. Ultimate technical Strength b. Ultimate tensile Strength* c. Upper Top surface d. None of above

Last Answer : b. Ultimate tensile Strength*

“Composite sleeper index” is employed to determine a) sleeper density requirement b) number of fixtures required for a particular type of sleeper c) durability of sleeper d) mechanical strength of wooden sleepers and thereby gives its suitability as to be used as li sleepers.*

Description : “Composite sleeper index” is employed to determine a) sleeper density requirement b) number of fixtures required for a particular type of sleeper c) durability of sleeper d) mechanical strength of wooden sleepers and thereby gives its suitability as to be used as li sleepers.*

Last Answer : d) mechanical strength of wooden sleepers and thereby gives its suitability as to be used as li sleepers.*

Wrought iron is not (A) Ductile & resistant to corrosion/rusting (B) Weldable easily (C) Having uniform strength in all directions (D) Having maximum tensile strength along the lines of slag distribution

Description : Wrought iron is not (A) Ductile & resistant to corrosion/rusting (B) Weldable easily (C) Having uniform strength in all directions (D) Having maximum tensile strength along the lines of slag distribution

Last Answer : Option C

The ratio of volume of air voids to the volume of voids is known as a) Percentage of air voids b) Porosity c) Degree of saturation d) Air content*

Description : The ratio of volume of air voids to the volume of voids is known as a) Percentage of air voids b) Porosity c) Degree of saturation d) Air content*

Last Answer : d) Air content*

The ratio of volume of water present in a given soil sample to the total volume of voids in it is known as a) Percentage of air voids b) Degree of saturation * c) Void rat

Description : The ratio of volume of water present in a given soil sample to the total volume of voids in it is known as a) Percentage of air voids b) Degree of saturation * c) Void rat

Last Answer : b) Degree of saturation *

Dry rot (A) Cracks the timber (B) Reduces the strength of timber (C) Reduces the timber to powder (D) Spoils the appearance of timber

Description : Dry rot (A) Cracks the timber (B) Reduces the strength of timber (C) Reduces the timber to powder (D) Spoils the appearance of timber

Last Answer : Answer: Option C

Seasoning of timber is done for (A) Increasing moisture content (B) Decreasing moisture content (C) Increasing strength of timber (D) None to these

Description : Seasoning of timber is done for (A) Increasing moisture content (B) Decreasing moisture content (C) Increasing strength of timber (D) None to these

Last Answer : Answer: Option B

A number of forces acting at a point will be in equilibrium if a.Sum of the forces is zero b.Algebraic sum of the forces is zero c.Sum of the resolved parts in any two perpendicular directions are both zero d.None of the above e.The metacentre of the body

Description : A number of forces acting at a point will be in equilibrium if a.Sum of the forces is zero b.Algebraic sum of the forces is zero c.Sum of the resolved parts in any two perpendicular directions are both zero d.None of the above e.The metacentre of the body

Last Answer : d. None of the above

Pick up the correct statement from the following: (A) The distance of the eccentric axial load from the C.G. beyond which tension develops, is known as kern distance (B) In visco-elastic material, stress-strain relation is dependent on time (C) An orthotropic material has different properties in three mutually perpendicular directions (D) All the above

Description : Pick up the correct statement from the following: (A) The distance of the eccentric axial load from the C.G. beyond which tension develops, is known as kern distance (B) In visco ... (C) An orthotropic material has different properties in three mutually perpendicular directions (D) All the above

Last Answer : (D) All the above

A number of forces acting at a point will be in equilibrium if (A) Their total sum is zero (B) Two resolved parts in two directions at right angles are equal (C) Sum of resolved parts in any two perpendicular directions are both zero (D) All of them are inclined equally

Description : A number of forces acting at a point will be in equilibrium if (A) Their total sum is zero (B) Two resolved parts in two directions at right angles are equal (C) Sum of resolved parts in any two perpendicular directions are both zero (D) All of them are inclined equally

Last Answer : (C) Sum of resolved parts in any two perpendicular directions are both zero

In a two way slab flexural bending develops [ A ] Along short span [ B ] Along long span [ C ] In Mutually perpendicular directions [ D ] At the center of short span

Description : In a two way slab flexural bending develops [ A ] Along short span [ B ] Along long span [ C ] In Mutually perpendicular directions [ D ] At the center of short span

Last Answer : [ C ] In Mutually perpendicular directions

When the field is strong, the lines of force are: (a) Closer (b) Parallel (c) Farther (d) All of above 45. The electric lines of force determine the strength of an: (a) Gravitational field (b) Constant field (c) Magnetic field (d) Electric field

Description : When the field is strong, the lines of force are: (a) Closer (b) Parallel (c) Farther (d) All of above 45. The electric lines of force determine the strength of an: (a) Gravitational field (b) Constant field (c) Magnetic field (d) Electric field

Last Answer : d) Electric field

Plywood has the advantage of (A) Greater tensile strength in longer direction (B) Greater tensile strength in shorter direction (C) Same tensile strength in all directions (D) None of the above

Description : Plywood has the advantage of (A) Greater tensile strength in longer direction (B) Greater tensile strength in shorter direction (C) Same tensile strength in all directions (D) None of the above

Last Answer : Answer: Option C