Lowering the flaps during a landing approach: a. Increases the angle of descent without increasing the airspeed b. Decreases the angle of descent without increasing power c. Eliminates floating d. Permits approaches at a higher indicated airspeed

Lowering the flaps during a landing approach:  
a. Increases the angle of descent without increasing the airspeed  
b. Decreases the angle of descent without increasing power  
c. Eliminates floating  
d. Permits approaches at a higher indicated airspeed
by

1 Answer

Answer :

a. Increases the angle of descent without increasing the airspeed
by

Related questions

t higher elevation airports the pilot should know that indicated airspeed: a. will be unchanged but ground speed will be faster b. will be higher but ground speed will be unchanged c. should be increased to compensate for the thinner air d. should be higher to obtain a higher landing speed

Description : t higher elevation airports the pilot should know that indicated airspeed: a. will be unchanged but ground speed will be faster b. will be higher but ground speed will be unchanged c. should be increased to compensate for the thinner air d. should be higher to obtain a higher landing speed

Last Answer : a. will be unchanged but ground speed will be faster

If a landing is to be made without flaps, the landing speed must be: a. reduced b. increased c. the same as for landing with flaps d. the same as for landing with flaps but with a steeper approach

Description : If a landing is to be made without flaps, the landing speed must be: a. reduced b. increased c. the same as for landing with flaps d. the same as for landing with flaps but with a steeper approach

Last Answer : b. increased

The method of alighting the aeroplane on water during a ditching is to: a. Carry out a normal approach with flaps and gear selected as normal but to calculate all speeds plus 10kts b. Reduce the approach angle to 1.5deg (150ft/mile), add 15kts to all speeds, keep the aeroplane clean (no flaps or gear) and fly it into the surface c. Fly a normal approach but keep the gear up and land at lowest possible speed with the nose raised for the tail to strike first d. Fly a normal approach to stalling speed and then drop the aeroplane vertically onto the water

Description : The method of alighting the aeroplane on water during a ditching is to: a. Carry out a normal approach with flaps and gear selected as normal but to calculate all speeds plus 10kts b. Reduce ... d. Fly a normal approach to stalling speed and then drop the aeroplane vertically onto the water

Last Answer : c. Fly a normal approach but keep the gear up and land at lowest possible speed with the nose raised for the tail to strike first

When entering a steep turn, an IVSI is likely to show: a. No change in altitude b. A slight climb c. A slight descent d. A slight descent at high airspeed only

Description : When entering a steep turn, an IVSI is likely to show: a. No change in altitude b. A slight climb c. A slight descent d. A slight descent at high airspeed only

Last Answer : b. A slight climb

Which of the following increases the stall angle? a. Slats b. Flaps c. Spoilers d. Ailerons

Description : Which of the following increases the stall angle? a. Slats b. Flaps c. Spoilers d. Ailerons

Last Answer : a. Slats

What true airspeed and angle of attack should be used to generate the same amount of lift as altitude is increased? a. A higher true airspeed for any given angle of attack b. The same true airspeed and angle of attack c. A lower true airspeed and higher angle of attack d. A constant angle of attack and true airspeed

Description : What true airspeed and angle of attack should be used to generate the same amount of lift as altitude is increased? a. A higher true airspeed for any given angle of attack b. The same true ... c. A lower true airspeed and higher angle of attack d. A constant angle of attack and true airspeed

Last Answer : a. A higher true airspeed for any given angle of attack

If the weight of an aircraft is increased the maximum gliding range: a. Decreases b. Increases c. Remains the same, and rate of descent is unchanged d. Remains the same, but rate of descent increases

Description : If the weight of an aircraft is increased the maximum gliding range: a. Decreases b. Increases c. Remains the same, and rate of descent is unchanged d. Remains the same, but rate of descent increases

Last Answer : d. Remains the same, but rate of descent increases

Shortly after take-off, the altitude of the aeroplane suffers an abrupt pitch-up and IAS rapidly decreases followed quickly by a decrease in altitude. Engine indications are normal. You should suspect what and what should you do? a. Marked temperature drop; apply full power b. Loss of head wind or an increase in tail wind; apply full power c. Incipient engine failure (ignore instruments); lower the nose to gain airspeed d. Local clear air turbulence; reduce speed to VRA and ride it out

Description : Shortly after take-off, the altitude of the aeroplane suffers an abrupt pitch-up and IAS rapidly decreases followed quickly by a decrease in altitude. Engine indications are normal. You should suspect what ... to gain airspeed d. Local clear air turbulence; reduce speed to VRA and ride it out

Last Answer : b. Loss of head wind or an increase in tail wind; apply full power

Which wind-shear condition results in a loss of airspeed? a. Decreasing headwind or tailwind b. Increasing headwind and decreasing tailwind c. Decreasing headwind and increasing tailwind d. Increasing headwind or tailwind

Description : Which wind-shear condition results in a loss of airspeed? a. Decreasing headwind or tailwind b. Increasing headwind and decreasing tailwind c. Decreasing headwind and increasing tailwind d. Increasing headwind or tailwind

Last Answer : c. Decreasing headwind and increasing tailwind

A hand pump is usually fitted: a. For ground servicing purposes b. Lowering the landing gear in an emergency c. Pressurising the oleo struts in the air d. Retracting the gear after take-off

Description : A hand pump is usually fitted: a. For ground servicing purposes b. Lowering the landing gear in an emergency c. Pressurising the oleo struts in the air d. Retracting the gear after take-off

Last Answer : a. For ground servicing purposes

To give the best obstacle clearance on take-off, take-off should be made with: a. Flaps partially extended and at best rate of climb speed (Vy) b. Flaps partially extended and at best angle of climb speed (Vx) c. Flaps retracted and at best rate of climb speed (Vy) d. Flaps retracted and at best angle of climb speed (Vx)

Description : To give the best obstacle clearance on take-off, take-off should be made with: a. Flaps partially extended and at best rate of climb speed (Vy) b. Flaps partially extended and at best angle of climb ... at best rate of climb speed (Vy) d. Flaps retracted and at best angle of climb speed (Vx)

Last Answer : d. Flaps retracted and at best angle of climb speed (Vx)

What is the effect of deploying leading edge flaps? a. Increased minimum glide angle b. Decreased minimum glide angle c. Increased glide range d. Decreased sink rate

Description : What is the effect of deploying leading edge flaps? a. Increased minimum glide angle b. Decreased minimum glide angle c. Increased glide range d. Decreased sink rate

Last Answer : d. Decreased sink rate

On an ILS approach, you are told that the weather has dropped below company minima. When must you abort the approach? a. Start of the glide-slope descent b. FAF c. Inner marker d. Outer marker

Description : On an ILS approach, you are told that the weather has dropped below company minima. When must you abort the approach? a. Start of the glide-slope descent b. FAF c. Inner marker d. Outer marker

Last Answer : d. Outer marker

By changing the angle of attack of a wing, the pilot can control the aeroplane’s: a. Lift and airspeed, but not drag b. Lift, gross weight and drag c. Lift, airspeed and drag d. Lift and drag, but not airspeed

Description : By changing the angle of attack of a wing, the pilot can control the aeroplane’s: a. Lift and airspeed, but not drag b. Lift, gross weight and drag c. Lift, airspeed and drag d. Lift and drag, but not airspeed

Last Answer : c. Lift, airspeed and drag

If the angle of attack is increased beyond the critical angle of attack, the wing will no longer produce sufficient lift to support the weight of the aircraft: a. Unless the airspeed is greater than the normal stall speed b. Regardless of airspeed or pitch attitude c. Unless the pitch attitude is on or below the natural horizon d. In which case, the control column should be pulled-back immediately

Description : If the angle of attack is increased beyond the critical angle of attack, the wing will no longer produce sufficient lift to support the weight of the aircraft: a. Unless the airspeed is greater ... below the natural horizon d. In which case, the control column should be pulled-back immediately

Last Answer : b. Regardless of airspeed or pitch attitude

At a constant mass and altitude, a lower airspeed requires: a. More thrust and a lower coefficient of lift b. Less thrust and a lower coefficient of lift c. More thrust and a lower coefficient of drag d. A higher coefficient of lift

Description : At a constant mass and altitude, a lower airspeed requires: a. More thrust and a lower coefficient of lift b. Less thrust and a lower coefficient of lift c. More thrust and a lower coefficient of drag d. A higher coefficient of lift

Last Answer : d. A higher coefficient of lift

The longitudinal separation minimum based on time between aircrafts at the same FL, where there is enough coverage for navigation aids and the preceeding aircraft has a higher true airspeed of 20kts minimum is: a. 3 minutes b. 15 minutes c. 5 minutes d. 10 minutes

Description : The longitudinal separation minimum based on time between aircrafts at the same FL, where there is enough coverage for navigation aids and the preceeding aircraft has a higher true airspeed of 20kts minimum is: a. 3 minutes b. 15 minutes c. 5 minutes d. 10 minutes

Last Answer : c. 5 minutes

If airbrakes are extended during a glide, and speed maintained, the rate of descent will: a. Increase and glide angle will be steeper b. Increase but glide angle will remain the same c. Decrease d. Remain the same

Description : If airbrakes are extended during a glide, and speed maintained, the rate of descent will: a. Increase and glide angle will be steeper b. Increase but glide angle will remain the same c. Decrease d. Remain the same

Last Answer : a. Increase and glide angle will be steeper

In recovery from a spin: a. Ailerons should be kept neutral b. Airspeed increases c. Ailerons used to stop the spin d. Rudder and ailerons used against the direction of spin direction

Description : In recovery from a spin: a. Ailerons should be kept neutral b. Airspeed increases c. Ailerons used to stop the spin d. Rudder and ailerons used against the direction of spin direction

Last Answer : a. Ailerons should be kept neutral

An aeroplane is starting a non-precision approach with an MDH of 250ft and minimum visibility of 800 meters. ATC gives threshold, mid-runway and final third RVRs. When may the approach be started? a. When threshold and mid-runway RVRs are greater than 800m b. When all 3 RVRs are greater than 800m c. When the met viz is greater than 800m. RVR is for precision approaches only. d. When threshold RVR is greater than 800m

Description : An aeroplane is starting a non-precision approach with an MDH of 250ft and minimum visibility of 800 meters. ATC gives threshold, mid-runway and final third RVRs. When may the approach be started? ... than 800m. RVR is for precision approaches only. d. When threshold RVR is greater than 800m

Last Answer : d. When threshold RVR is greater than 800m

A precautionary landing is a procedure that: a. Enables the aeroplane to land at the destination with unserviceabilities that prevent a normal instrument approach being carried out b. Enables a landing after the declaration of a state of emergency or urgency c. Enables a landing if it is suspected that the undercarriage is not properly lowered d. Is carried out in the event of landing at an alternate aerodrome

Description : A precautionary landing is a procedure that: a. Enables the aeroplane to land at the destination with unserviceabilities that prevent a normal instrument approach being carried out b. Enables a ... not properly lowered d. Is carried out in the event of landing at an alternate aerodrome

Last Answer : b. Enables a landing after the declaration of a state of emergency or urgency

What factors affect descent angle in a glide? a. Configuration and altitude b. Configuration and angle of attack c. Mass and altitude d. Mass and configuration

Description : What factors affect descent angle in a glide? a. Configuration and altitude b. Configuration and angle of attack c. Mass and altitude d. Mass and configuration

Last Answer : b. Configuration and angle of attack

If flaps are lowered during the take-off run: a. The lift would not change until the aircraft is airborne b. The lift would increase when the flaps are lowered c. The lift would decrease d. The acceleration would increase

Description : If flaps are lowered during the take-off run: a. The lift would not change until the aircraft is airborne b. The lift would increase when the flaps are lowered c. The lift would decrease d. The acceleration would increase

Last Answer : b. The lift would increase when the flaps are lowered

What is the recommended technique to counter the loss of airspeed and resultant lift from wind shear? a. Maintain, or increase, pitch attitude and accept the lower-than-normal airspeed indications b. Lower the pitch attitude and regain lost airspeed c. Avoid overstressing aircraft, pitch to stick shaker, and apply maximum power d. Accelerate the aircraft to prevent a stall by sacrificing altitude

Description : What is the recommended technique to counter the loss of airspeed and resultant lift from wind shear? a. Maintain, or increase, pitch attitude and accept the lower-than-normal airspeed ... shaker, and apply maximum power d. Accelerate the aircraft to prevent a stall by sacrificing altitude

Last Answer : c. Avoid overstressing aircraft, pitch to stick shaker, and apply maximum power

A constant rate of climb in an aeroplane is determined by: a. Wind speed b. The aircraft weight c. Excess engine power d. Excess airspeed

Description : A constant rate of climb in an aeroplane is determined by: a. Wind speed b. The aircraft weight c. Excess engine power d. Excess airspeed

Last Answer : c. Excess engine power

The control surface which gives longitudinal control is: a. The rudder b. The ailerons c. The elevators d. The flaps

Description : The control surface which gives longitudinal control is: a. The rudder b. The ailerons c. The elevators d. The flaps

Last Answer : c. The elevators

When does the first segment of the take-off climb begin? a. When V2 is reached b. When 35 feet is reached c. When flaps are up d. When gear and flaps are up

Description : When does the first segment of the take-off climb begin? a. When V2 is reached b. When 35 feet is reached c. When flaps are up d. When gear and flaps are up

Last Answer : b. When 35 feet is reached

How can the pilot increase the rate of turn and decrease the radius at the same time? a. Shallow the bank and increase airspeed b. Steeper bank and increase airspeed c. Steeper bank and decrease airspeed

Description : How can the pilot increase the rate of turn and decrease the radius at the same time? a. Shallow the bank and increase airspeed b. Steeper bank and increase airspeed c. Steeper bank and decrease airspeed

Last Answer : c. Steeper bank and decrease airspeed

Two aircrafts, one with a sharp wing profile (S) and the other with a thick profile (T), are flying through the same cloud with the same true airspeed. The cloud consists of small supercooled droplets. Which of the following statements is most correct concerning ice accretion? a. Aircraft T experiences more icing than S b. Aircraft S and T experience the same amount of icing c. Neither of the aircrafts accumulate ice due to the small size of droplets d. Aircraft S experiences more icing than T

Description : Two aircrafts, one with a sharp wing profile (S) and the other with a thick profile (T), are flying through the same cloud with the same true airspeed. The cloud consists of small ... aircrafts accumulate ice due to the small size of droplets d. Aircraft S experiences more icing than T

Last Answer : d. Aircraft S experiences more icing than T

Which of the following instruments require inputs of both pitot and static pressure? a. Airspeed indicator, machmeter and vertical speed indicator b. Airspeed indicator, vertical speed indicator, altimeter c. Airspeed indicator only d. Airspeed indicator and machmeter

Description : Which of the following instruments require inputs of both pitot and static pressure? a. Airspeed indicator, machmeter and vertical speed indicator b. Airspeed indicator, vertical speed indicator, altimeter c. Airspeed indicator only d. Airspeed indicator and machmeter

Last Answer : d. Airspeed indicator and machmeter

In the event of cabin depressurization, the actions of the pilot will be to: a. Immediately commence a diversion to a suitable alternate b. Increase engine power to provide additional airflow to the pressurization systems c. Maintain the aeroplane altitude to prevent further damage to the airframe by over loading of the structure d. Commence a descent to an altitude where the supplemental oxygen supply is sufficient for all crew and passengers

Description : In the event of cabin depressurization, the actions of the pilot will be to: a. Immediately commence a diversion to a suitable alternate b. Increase engine power to provide additional ... a descent to an altitude where the supplemental oxygen supply is sufficient for all crew and passengers

Last Answer : d. Commence a descent to an altitude where the supplemental oxygen supply is sufficient for all crew and passengers

When is spark plug fouling most likely to occur? a. In the climb if you have not adjusted the mixture b. Cruise power c. In the descent if you have not adjusted the mixture d. Max take-off power

Description : When is spark plug fouling most likely to occur? a. In the climb if you have not adjusted the mixture b. Cruise power c. In the descent if you have not adjusted the mixture d. Max take-off power

Last Answer : a. In the climb if you have not adjusted the mixture

When would the negative differential limits be reached/exceeded? a. Rapid descent when AC descends below cabin altitude b. During ground pressure testing c. Rapid ascent when aircraft climbs d. When changing to manual operation

Description : When would the negative differential limits be reached/exceeded? a. Rapid descent when AC descends below cabin altitude b. During ground pressure testing c. Rapid ascent when aircraft climbs d. When changing to manual operation

Last Answer : a. Rapid descent when AC descends below cabin altitude

To maintain altitude, what must be done as Indicated Airspeeed (IAS) is reduced? a. Decrease angle of attack to reduce the drag b. Increase angle of attack to maintain the correct lift force c. Deploy the speed brakes to increase drag d. Reduce thrust

Description : To maintain altitude, what must be done as Indicated Airspeeed (IAS) is reduced? a. Decrease angle of attack to reduce the drag b. Increase angle of attack to maintain the correct lift force c. Deploy the speed brakes to increase drag d. Reduce thrust

Last Answer : b. Increase angle of attack to maintain the correct lift force

Aircraft A flies in VMC with an ATC clearance within a control area. Aircraft B without ATC clearance approaches at roughly the same height on a converging heading. Who has the right of way? a. Aircraft A, regardless of the direction from which B approaches b. Aircraft B, regardless of the direction from which A approaches c. Aircraft A, if B is to the right of him d. Aircraft B, if A is to the left of him

Description : Aircraft A flies in VMC with an ATC clearance within a control area. Aircraft B without ATC clearance approaches at roughly the same height on a converging heading. Who has the right of way? a. Aircraft A, regardless ... , if B is to the right of him d. Aircraft B, if A is to the left of him

Last Answer : d. Aircraft B, if A is to the left of him

Which action shall be taken by an aircraft in the traffic pattern of an aerodrome experiencing radio failure to indicate difficulties which compel it to land without requiring immediate assistance? a. Switching on and off three times the landing lights b. The repeated switching on and off of the landing lights c. Switching on and off four times the navigation lights d. Switching on and off four times the landing lights

Description : Which action shall be taken by an aircraft in the traffic pattern of an aerodrome experiencing radio failure to indicate difficulties which compel it to land without requiring immediate assistance? a. ... four times the navigation lights d. Switching on and off four times the landing lights

Last Answer : b. The repeated switching on and off of the landing lights

The transition of altitude to flight level and vice versa is made: a. On the transition level in the climb and transition altitude in the descent b. At the transition altitude in the climb and transition level in the descent c. At the transition level only d. At the transition altitude only

Description : The transition of altitude to flight level and vice versa is made: a. On the transition level in the climb and transition altitude in the descent b. At the transition altitude in the climb and transition level in the descent c. At the transition level only d. At the transition altitude only

Last Answer : b. At the transition altitude in the climb and transition level in the descent

If cabin pressure is decreasing, the cabin VSI will indicate: a. Zero b. Climb c. Descent d. Reducing pressure

Description : If cabin pressure is decreasing, the cabin VSI will indicate: a. Zero b. Climb c. Descent d. Reducing pressure

Last Answer : b. Climb

An aircraft is travelling at 100kts forward speed on a 3° glidescope. What is its rate of descent? a. 500 ft/min b. 300 ft/min c. 250 ft/min d. 600 ft/min

Description : An aircraft is travelling at 100kts forward speed on a 3° glidescope. What is its rate of descent? a. 500 ft/min b. 300 ft/min c. 250 ft/min d. 600 ft/min

Last Answer : a. 500 ft/min

When entering a steep turn, an IVSI is likely to show: a. No change in altitude b. A slight climb c. A slight descent d. A slight descent at high airspeed only

Description : When entering a steep turn, an IVSI is likely to show: a. No change in altitude b. A slight climb c. A slight descent d. A slight descent at high airspeed only

Last Answer : b. A slight climb

What is DH used for? a. Visual maneuvering b. Circling to land c. Precision approaches d. Non-precision approaches

Description : What is DH used for? a. Visual maneuvering b. Circling to land c. Precision approaches d. Non-precision approaches

Last Answer : c. Precision approaches

Where a medium category aeroplane is landing behind a heavy category aeroplane, the minimum separation distance in NM is: a. 3 b. 4 c. 5 d. 6

Description : Where a medium category aeroplane is landing behind a heavy category aeroplane, the minimum separation distance in NM is: a. 3 b. 4 c. 5 d. 6

Last Answer : c. 5

Where a light category aeroplane is landing behind a medium category aeroplane, minimum separation distance in NM is: a. 6 b. 5 c. 4 d. 3

Description : Where a light category aeroplane is landing behind a medium category aeroplane, minimum separation distance in NM is: a. 6 b. 5 c. 4 d. 3

Last Answer : b. 5

In the event of a precautionary landing, who is responsible for alerting the emergency services? a. ATC b. The Commander c. The local constabulary d. The Operations Dispatcher

Description : In the event of a precautionary landing, who is responsible for alerting the emergency services? a. ATC b. The Commander c. The local constabulary d. The Operations Dispatcher

Last Answer : a. ATC

When do you not need a destination alternate aerodrome? a. If there is a reasonable certainty that at the ETA at the destination aerodrome and a reasonable time before and after you can expect VMC b. If the flight time is less than 6 hours c. If the flight time is less than 1 hour d. If your operator deems the weather to be suitable for a visual landing

Description : When do you not need a destination alternate aerodrome? a. If there is a reasonable certainty that at the ETA at the destination aerodrome and a reasonable time before and after you can expect VMC ... less than 1 hour d. If your operator deems the weather to be suitable for a visual landing

Last Answer : a. If there is a reasonable certainty that at the ETA at the destination aerodrome and a reasonable time before and after you can expect VMC

To act as co-pilot for take-off or landing, you must have: a. Acted as PIC or co-pilot on type in the last 90 days b. Acted as PIC or co-pilot on type in the last 30 days c. Acted as PIC or co-pilot on type in the last 60 days d. Been at the controls for landing in the same type recently

Description : To act as co-pilot for take-off or landing, you must have: a. Acted as PIC or co-pilot on type in the last 90 days b. Acted as PIC or co-pilot on type in the last 30 days c. Acted as PIC or co-pilot on type in the last 60 days d. Been at the controls for landing in the same type recently

Last Answer : a. Acted as PIC or co-pilot on type in the last 90 days

Refer to CAP697 MRJT1 Fig. 4.3.1 Given: Estimated zero fuel mass 50t; estimated landing mass at destination 52t; final reserve fuel 2t; alternate fuel 1t; flight to destination distance 720nm, true course 030, W/V 340/30; cruise: LRC, at FL330 outside air temperature -30C. Find estimated trip fuel and time. a. 4,800kg / 01hr 45min b. 4,400kg / 02hr 02min c. 4,750kg / 02hr 00min d. 4,600kg / 02hr 05min

Description : Refer to CAP697 MRJT1 Fig. 4.3.1 Given: Estimated zero fuel mass 50t; estimated landing mass at destination 52t; final reserve fuel 2t; alternate fuel 1t; flight to destination distance 720nm, true course 030, W/V ... b. 4,400kg / 02hr 02min c. 4,750kg / 02hr 00min d. 4,600kg / 02hr 05min

Last Answer : a. 4,800kg / 01hr 45min

Refer to CAP697 MRJT1 Fig. 4.3.6 Given: Distance to alternate 400nm Landing mass at alternate 50,000kg Headwind component 25kt The alternate fuel required is: a. 2550kg b. 2800kg c. 2900kg d. 2650kg

Description : Refer to CAP697 MRJT1 Fig. 4.3.6 Given: Distance to alternate 400nm Landing mass at alternate 50,000kg Headwind component 25kt The alternate fuel required is: a. 2550kg b. 2800kg c. 2900kg d. 2650kg

Last Answer : b. 2800kg

DOM 33,510kt; Traffic load 7,600kg; Trip fuel 2040kg; Final reserve 983kg Alternative fuel 1100kg; Contingency 5% of trip fuel Which of the following is correct? a. Estimated landing mass at destination 43,193kg b. Estimated landing mass at destination 43,295kg c. Estimated take-off mass 43,295kg d. Estimated take-off mass 45,233kg

Description : DOM 33,510kt; Traffic load 7,600kg; Trip fuel 2040kg; Final reserve 983kg Alternative fuel 1100kg; Contingency 5% of trip fuel Which of the following is correct? a. Estimated landing mass at destination ... 43,295kg c. Estimated take-off mass 43,295kg d. Estimated take-off mass 45,233kg

Last Answer : b. Estimated landing mass at destination 43,295kg

What is the Total Elapsed Time on a VFR flight plan? a. From take-off to overhead destination b. From take-off to overhead destination + 15 mins c. From take-off to landing d. From taxi to arrival on the gate

Description : What is the Total Elapsed Time on a VFR flight plan? a. From take-off to overhead destination b. From take-off to overhead destination + 15 mins c. From take-off to landing d. From taxi to arrival on the gate

Last Answer : a. From take-off to overhead destination