Description : Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate
Last Answer : a)peripheral speed of the drum
Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm
Last Answer : d) 1100-1200rpm
Description : Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above
Last Answer : (a) Increase threshing efficiency
Description : Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above
Last Answer : d) All of the above
Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.
Last Answer : 1200 to 1500
Description : Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peCylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above
Last Answer : M. Cylinder peripheral speed
Description : The peripheral velocity at inlet of a centrifugal pump having inlet diameter of 25 cms and rotating at 950 rpm is __________ m/sec. (A) 1.8 (B) 12.4 (C) 186.2 (D) 736.4
Last Answer : (B) 12.4
Description : Kinematic index of the straw Walker is as ratio (a) Angular velocity of straw Walker to angular velocity of threshing drum (b) Angular velocity of straw Walker to angular velocity of threshing drum (c) Angular velocity of straw Walker to linear velocity of combine (d) All of the above
Last Answer : (a) Angular velocity of straw Walker to angular velocity of threshing drum
Description : Cleaning of sugarcane is obtained at peripheral speed A. 12-15m/sec B. 18-20m/sec C. 20-25m/sec D. 25-30m/sec
Last Answer : B. 18-20m/sec
Description : Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder
Last Answer : a.) Decreasing cylinder peripheral speed.
Description : The threshing efficiency of thresher depends on a) Cylinder peripheral speed b) Cylinder concave clearance c) Feed rate, moisture content and type of crop d) All are correct
Last Answer : All are correct
Description : A stone is dropped into a deep shaft without any initial velocity. The sound of the stone hitting the bottom is heard after 4 seconds. If the velocity of sound is 330 m/sec the depth of the shaft will be a.33.1 m b.660 m c.165 m d.66.2 m e.330 m
Last Answer : d. 66.2 m
Description : The mechanical cleaning of sugar cane is done due to A. The different in the peripheral velocity of rollers B. Rough surface provided Or the outer surface of rollers C. Blow of air which forces the extraneous material out of the machine D. All of the above
Last Answer : D. All of the above
Description : The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index
Last Answer : (c)reel speed index
Description : A thick cylinder is subjected to an internal pressure of 60 MPa. If the hoop stress on the outer surface is 150 MPa, then the hoop stress on the internal surface is a) 105 MPa b) 180 MPa c) 210 MPa d) 135 MPa.
Last Answer : c) 210 MPa
Description : Reaper is used for a.) Plowing b.) Harvesting and threshing. c.) Cutting crops. d.) Cutting and windrow.
Last Answer : d.) Cutting and windrow.
Description : A reaper used for : a. Cutting crop b. Cutting and windrewing c. Cutting and threshing d. None of these
Last Answer : b. Cutting and windrewing
Description : Differential lock offers advantage of E. Threshing efficiency of thresher (power operated) F. Capacity of chaff cutters G. Cleaning capacity of straw walkers H. None of the above
Last Answer : F. Capacity of chaff cutters
Description : eripheral velocity of impact cutter is about: A.50m/sec B.20m/sec C.10m/sec D.5m/sec
Last Answer : A.50m/sec
Description : Theoretical capacity of crushing rolls in tons/hr is given by (where, V = peripheral velocity, m/sec. W = width of rolls, m Dr = distance between rolls ρ = density of material to be crushed, kg/m3 here, V =πND where, N = speed of the rolls ... V.W.Dr.ρ (B) 3.6 V.W. ρ (C) 3.6 W.Dr.ρ (D) 3.6 V.W.Dr/ρ
Last Answer : (A) 3.6 V.W.Dr.ρ
Description : The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance ... up units (cells) on the metering unit c) Both (a) and (b) d) None of the above
Last Answer : c) Both (a) and (b)
Description : _______ designates the shape of gross peripheral and cross-sectional boundaries of the soil working tool a) Micro shape c) Edge shape b) Macro shape d) Gross shape
Last Answer : c) Edge shape
Description : Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above
Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm
Last Answer : c) 600-800rpm
Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above
Last Answer : B. L-head
Description : An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above
Last Answer : d) None of the above
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill
Last Answer : a) Raspbar type cylinder
Description : Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more
Last Answer : a) Higher cylinder speed.
Description : The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails
Last Answer : c) Spike tooth and hammer mill
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill
Description : Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder
Last Answer : (b) Spike tooth cylinder
Description : Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above
Last Answer : (a) Cylinder losses
Description : iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above
Last Answer : ∙ Torque is a function of thermal efficiency
Description : Compression pressure in petrol engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) 35-40 kg/cm2
Last Answer : a) 6-10 kg/cm2
Description : Compression pressure in diesel engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) None of the above
Last Answer : c) 20-35 kg/cm2
Description : Firing order of a six cylinder engine in which no two adjacent cylinder have power stroke is (a) 1 5 3 6 2 4 (b) 1 2 3 4 5 6 (c) 1 5 4 6 3 2 (d) 1 4 2 5 6 3
Last Answer : (a) 1 5 3 6 2 4
Description : hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder
Last Answer : (b) number of power stroke per minute for all cylinders
Description : 349- Pods, heads or ears & freeseeds, lost during the cutting & conveying operation are called as..... (a) Cylinder loss (b) Walker losses ( rack loss) (c) Shoe losses (d) Gathering loss
Last Answer : (d) Gathering loss
Description : Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above
Last Answer : a) Cylinder losses
Description : Free (threshed) seed carried over the straw discharged from the rear shoe is called as (a) Cylinder loss (b)walker loss (rack Loss) (b) Shoe loss (d) gathering loss
Last Answer : (b) Shoe loss
Description : Free (threshed) seed carried over the walker or rack in straw and discharge from the rear of machine is called as (a) Cylinder loss (b) walker loss(rack loss) (c) Shoe loss (d) gathering loss
Last Answer : (b) walker loss(rack loss)
Description : Unthreshed seed discharged from the rear of the machine either in straw or in the material from the cleaning shoe is called (a)cylinder loss (b)walker loss (rack loss) (c)shoe loss (d) gathering loss
Last Answer : (a)cylinder loss
Description : Work done by a body of mass 100 kg moving along a circular path of radius 2 m with a uniform velocity of 10 m/sec is a.5000 J b.2500 J c.509.68 J d.None of the above e.Tapered bearing
Last Answer : d. None of the above
Description : For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these
Last Answer : D)all of these
Description : For batching 1:3:6 concrete mix by volume, the ingredients required per bag of 50 kg cement, are: (A) 70 litres of sand and 120 litres of aggregates (B) 70 kg of sand and 140 litres of ... C) 105 litres of sand and 140 litres of aggregates (D) 105 litres of sand and 210 litres of aggregates
Last Answer : Answer: Option D
Description : The missing number in the series 40, 120, 60, 180, 90, ?, 135 is (A) 110 (B) 270 (C) 105 (D) 210
Last Answer : Answer: B
Description : A convex mirror and a concave mirror of radius 10cm each are placed 15cm apart facing each other. An object is placed midway between them. If the refl
Last Answer : A convex mirror and a concave mirror of radius 10cm each are placed 15cm apart facing each other ... convex mirror, the position of the final image is
Description : A cylindrical drum of 15cm radius and 70cm height is full of water. The water is emptied into a rectangular tank 225cm long and 70cm wide. Find the height of water level in the tank. a) 3.5cm b) 2.25cm c) 3.142cm d) 1.57cm
Last Answer : c) 3.142cm
Description : In a thresher, by increasing the speed of threshing cylinder a) Threshing efficiency can be increased b) Broken grain loss can be minimized c) Un-threshed grains can be increased d) Straw breakup can be increased Ans. a
Last Answer : ans a
Description : Different parts of Thresher are A) Feeding device B) Threshing cylinder C) Concave D) All of the above.
Last Answer : All of the above.