To recover from a spin, the elevators should be: a. Moved up to increase the angle of attack b. Moved down to reduce the angle of attack c. Set to neutral d. Allowed to float

To recover from a spin, the elevators should be:  
a. Moved up to increase the angle of attack  
b. Moved down to reduce the angle of attack  
c. Set to neutral  
d. Allowed to float
by

1 Answer

Answer :

b. Moved down to reduce the angle of attack
by

Related questions

To maintain altitude, what must be done as Indicated Airspeeed (IAS) is reduced? a. Decrease angle of attack to reduce the drag b. Increase angle of attack to maintain the correct lift force c. Deploy the speed brakes to increase drag d. Reduce thrust

Description : To maintain altitude, what must be done as Indicated Airspeeed (IAS) is reduced? a. Decrease angle of attack to reduce the drag b. Increase angle of attack to maintain the correct lift force c. Deploy the speed brakes to increase drag d. Reduce thrust

Last Answer : b. Increase angle of attack to maintain the correct lift force

In recovery from a spin: a. Ailerons should be kept neutral b. Airspeed increases c. Ailerons used to stop the spin d. Rudder and ailerons used against the direction of spin direction

Description : In recovery from a spin: a. Ailerons should be kept neutral b. Airspeed increases c. Ailerons used to stop the spin d. Rudder and ailerons used against the direction of spin direction

Last Answer : a. Ailerons should be kept neutral

What flight condition should be expected when an aircraft leaves ground effect? a. A decrease in parasite drag permitting a lower angle of attack b. An increase induced drag and a requirement for a higher angle of attack c. An increase in dynamic stability d. A decrease in induced drag requiring a smaller angle of attack

Description : What flight condition should be expected when an aircraft leaves ground effect? a. A decrease in parasite drag permitting a lower angle of attack b. An increase induced drag and a requirement ... increase in dynamic stability d. A decrease in induced drag requiring a smaller angle of attack

Last Answer : b. An increase induced drag and a requirement for a higher angle of attack

Which statement is true relative to changing angle of attack? a. A decrease in angle of attack will increase pressure below the wing and decrease drag b. An increase in angle of attack will decrease pressure below the wing and decrease drag c. An increase in angle of attack will increase drag d. An increase in angle of attack will decrease the lift coefficient

Description : Which statement is true relative to changing angle of attack? a. A decrease in angle of attack will increase pressure below the wing and decrease drag b. An increase in angle of attack will ... of attack will increase drag d. An increase in angle of attack will decrease the lift coefficient

Last Answer : c. An increase in angle of attack will increase drag

The control surface which gives longitudinal control is: a. The rudder b. The ailerons c. The elevators d. The flaps

Description : The control surface which gives longitudinal control is: a. The rudder b. The ailerons c. The elevators d. The flaps

Last Answer : c. The elevators

What true airspeed and angle of attack should be used to generate the same amount of lift as altitude is increased? a. A higher true airspeed for any given angle of attack b. The same true airspeed and angle of attack c. A lower true airspeed and higher angle of attack d. A constant angle of attack and true airspeed

Description : What true airspeed and angle of attack should be used to generate the same amount of lift as altitude is increased? a. A higher true airspeed for any given angle of attack b. The same true ... c. A lower true airspeed and higher angle of attack d. A constant angle of attack and true airspeed

Last Answer : a. A higher true airspeed for any given angle of attack

By changing the angle of attack of a wing, the pilot can control the aeroplane’s: a. Lift and airspeed, but not drag b. Lift, gross weight and drag c. Lift, airspeed and drag d. Lift and drag, but not airspeed

Description : By changing the angle of attack of a wing, the pilot can control the aeroplane’s: a. Lift and airspeed, but not drag b. Lift, gross weight and drag c. Lift, airspeed and drag d. Lift and drag, but not airspeed

Last Answer : c. Lift, airspeed and drag

Which stall has the greatest angle of attack? a. Low speed stall b. High speed stall (shock stall) c. Deep stall d. Accelerated stall

Description : Which stall has the greatest angle of attack? a. Low speed stall b. High speed stall (shock stall) c. Deep stall d. Accelerated stall

Last Answer : c. Deep stall

If the angle of attack is increased beyond the critical angle of attack, the wing will no longer produce sufficient lift to support the weight of the aircraft: a. Unless the airspeed is greater than the normal stall speed b. Regardless of airspeed or pitch attitude c. Unless the pitch attitude is on or below the natural horizon d. In which case, the control column should be pulled-back immediately

Description : If the angle of attack is increased beyond the critical angle of attack, the wing will no longer produce sufficient lift to support the weight of the aircraft: a. Unless the airspeed is greater ... below the natural horizon d. In which case, the control column should be pulled-back immediately

Last Answer : b. Regardless of airspeed or pitch attitude

The angle of attack of a fixed pitch propeller: a. Depends on forward speed only b. Depends on forward speed and engine rotational speed c. Depends on engine rotational speed only d. Is constant for a fixed pitch propeller

Description : The angle of attack of a fixed pitch propeller: a. Depends on forward speed only b. Depends on forward speed and engine rotational speed c. Depends on engine rotational speed only d. Is constant for a fixed pitch propeller

Last Answer : b. Depends on forward speed and engine rotational speed

What factors affect descent angle in a glide? a. Configuration and altitude b. Configuration and angle of attack c. Mass and altitude d. Mass and configuration

Description : What factors affect descent angle in a glide? a. Configuration and altitude b. Configuration and angle of attack c. Mass and altitude d. Mass and configuration

Last Answer : b. Configuration and angle of attack

The method of alighting the aeroplane on water during a ditching is to: a. Carry out a normal approach with flaps and gear selected as normal but to calculate all speeds plus 10kts b. Reduce the approach angle to 1.5deg (150ft/mile), add 15kts to all speeds, keep the aeroplane clean (no flaps or gear) and fly it into the surface c. Fly a normal approach but keep the gear up and land at lowest possible speed with the nose raised for the tail to strike first d. Fly a normal approach to stalling speed and then drop the aeroplane vertically onto the water

Description : The method of alighting the aeroplane on water during a ditching is to: a. Carry out a normal approach with flaps and gear selected as normal but to calculate all speeds plus 10kts b. Reduce ... d. Fly a normal approach to stalling speed and then drop the aeroplane vertically onto the water

Last Answer : c. Fly a normal approach but keep the gear up and land at lowest possible speed with the nose raised for the tail to strike first

Shortly after take-off, the altitude of the aeroplane suffers an abrupt pitch-up and IAS rapidly decreases followed quickly by a decrease in altitude. Engine indications are normal. You should suspect what and what should you do? a. Marked temperature drop; apply full power b. Loss of head wind or an increase in tail wind; apply full power c. Incipient engine failure (ignore instruments); lower the nose to gain airspeed d. Local clear air turbulence; reduce speed to VRA and ride it out

Description : Shortly after take-off, the altitude of the aeroplane suffers an abrupt pitch-up and IAS rapidly decreases followed quickly by a decrease in altitude. Engine indications are normal. You should suspect what ... to gain airspeed d. Local clear air turbulence; reduce speed to VRA and ride it out

Last Answer : b. Loss of head wind or an increase in tail wind; apply full power

A shuttle valve will: a. Allow the accumulator to be emptied after engine shut down b. Reduce pump loading when normal system pressure is reached c. Automatically switched to a more appropriate source of hydraulic supply d. Operate on a rising pressure, higher than the Full Flow relief valve

Description : A shuttle valve will: a. Allow the accumulator to be emptied after engine shut down b. Reduce pump loading when normal system pressure is reached c. Automatically switched to a more appropriate source of hydraulic supply d. Operate on a rising pressure, higher than the Full Flow relief valve

Last Answer : c. Automatically switched to a more appropriate source of hydraulic supply

What should the pilot rely on if disoriented in IMC? a. Vision b. Turning head to recover from disorientation c. Sense of balance d. Instruments

Description : What should the pilot rely on if disoriented in IMC? a. Vision b. Turning head to recover from disorientation c. Sense of balance d. Instruments

Last Answer : d. Instruments

What is normally the most effective measure to reduce or avoid CAT effects? a. Change of flight level b. Change of course c. Increase of speed d. Decrease of speed

Description : What is normally the most effective measure to reduce or avoid CAT effects? a. Change of flight level b. Change of course c. Increase of speed d. Decrease of speed

Last Answer : a. Change of flight level

If airbrakes are extended during a glide, and speed maintained, the rate of descent will: a. Increase and glide angle will be steeper b. Increase but glide angle will remain the same c. Decrease d. Remain the same

Description : If airbrakes are extended during a glide, and speed maintained, the rate of descent will: a. Increase and glide angle will be steeper b. Increase but glide angle will remain the same c. Decrease d. Remain the same

Last Answer : a. Increase and glide angle will be steeper

To ensure some degree of longitudinal stability in flight, the position of the CG: a. Must always coincide with the AC b. Must be forward of the Neutral Point c. Must be aft of the Neutral Point d. Must not be forward of the aft CG limi

Description : To ensure some degree of longitudinal stability in flight, the position of the CG: a. Must always coincide with the AC b. Must be forward of the Neutral Point c. Must be aft of the Neutral Point d. Must not be forward of the aft CG limi

Last Answer : b. Must be forward of the Neutral Point

A nose wheel control system a. Prevents the nosewheel from castering at all times b. Allows the nosewheel to caster within preset limits about the neutral position c. Allows the nosewheel to caster freely at all times d. Prevents the nose gear from lowering if the nosewheels are not centralised

Description : A nose wheel control system a. Prevents the nosewheel from castering at all times b. Allows the nosewheel to caster within preset limits about the neutral position c. Allows the nosewheel to ... freely at all times d. Prevents the nose gear from lowering if the nosewheels are not centralised

Last Answer : b. Allows the nosewheel to caster within preset limits about the neutral position

Pilots are not allowed to use the indent function on their SSR, unless: a. They operate outside controlled airspace b. If asked by ATC c. Within controlled airspace d. They operate a transponder with mode C

Description : Pilots are not allowed to use the indent function on their SSR, unless: a. They operate outside controlled airspace b. If asked by ATC c. Within controlled airspace d. They operate a transponder with mode C

Last Answer : b. If asked by ATC

An aircraft is allowed to descend below the MSA if: a. The pilot follows the published approach procedures b. The aircraft receives radar vectors c. The pilot has visual contact with the runway and surrounding terrain and is able to maintain visual contact d. All of the above

Description : An aircraft is allowed to descend below the MSA if: a. The pilot follows the published approach procedures b. The aircraft receives radar vectors c. The pilot has visual contact with the runway and surrounding terrain and is able to maintain visual contact d. All of the above

Last Answer : d. All of the above

From a pre-flight briefing you know a jet stream is at 31,000ft whilst you are at FL270. You experience moderate CAT. What would be the best course of action? a. Stay level b. Descend c. Climb d. Reduce speed

Description : From a pre-flight briefing you know a jet stream is at 31,000ft whilst you are at FL270. You experience moderate CAT. What would be the best course of action? a. Stay level b. Descend c. Climb d. Reduce speed

Last Answer : b. Descend

What is the purpose of inboard ailerons? a. To reduce wing bending at high speed b. To reduce wing twisting at low speed c. To reduce wing bending at low speed d. To reduce wing twist at high speed

Description : What is the purpose of inboard ailerons? a. To reduce wing bending at high speed b. To reduce wing twisting at low speed c. To reduce wing bending at low speed d. To reduce wing twist at high speed

Last Answer : d. To reduce wing twist at high speed

If a CSD overheat warning is shown: a. The CSD can be disconnected and the pilot must control the alternator himself b. The pilot must throttle back to reduce the load on the alternator c. The CSD can be disconnected then reconnected later when the temperature has reduced d. The CSD can be disconnected but not used for the rest of the flight

Description : If a CSD overheat warning is shown: a. The CSD can be disconnected and the pilot must control the alternator himself b. The pilot must throttle back to reduce the load on the alternator c. The ... temperature has reduced d. The CSD can be disconnected but not used for the rest of the flight

Last Answer : d. The CSD can be disconnected but not used for the rest of the flight

If the ailerons are deflected to 10°, compared to 5°, this will cause: a. An increased angle of bank b. An increased rate of roll c. No change to either bank angle or roll rate d. A reduction in the adverse yawing moment

Description : If the ailerons are deflected to 10°, compared to 5°, this will cause: a. An increased angle of bank b. An increased rate of roll c. No change to either bank angle or roll rate d. A reduction in the adverse yawing moment

Last Answer : b. An increased rate of roll

Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to remain unchanged b. The propeller control regulates the engine RPM and in turn the propeller RPM c. A high blade angle, or increased pitch, reduces the propeller drag and allows more engine power for take-offs d. As the propeller control setting is changed by the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Description : Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to ... the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Last Answer : b. The propeller control regulates the engine RPM and in turn the propeller RPM

To give the best obstacle clearance on take-off, take-off should be made with: a. Flaps partially extended and at best rate of climb speed (Vy) b. Flaps partially extended and at best angle of climb speed (Vx) c. Flaps retracted and at best rate of climb speed (Vy) d. Flaps retracted and at best angle of climb speed (Vx)

Description : To give the best obstacle clearance on take-off, take-off should be made with: a. Flaps partially extended and at best rate of climb speed (Vy) b. Flaps partially extended and at best angle of climb ... at best rate of climb speed (Vy) d. Flaps retracted and at best angle of climb speed (Vx)

Last Answer : d. Flaps retracted and at best angle of climb speed (Vx)

Which of the following increases the stall angle? a. Slats b. Flaps c. Spoilers d. Ailerons

Description : Which of the following increases the stall angle? a. Slats b. Flaps c. Spoilers d. Ailerons

Last Answer : a. Slats

What is the effect of deploying leading edge flaps? a. Increased minimum glide angle b. Decreased minimum glide angle c. Increased glide range d. Decreased sink rate

Description : What is the effect of deploying leading edge flaps? a. Increased minimum glide angle b. Decreased minimum glide angle c. Increased glide range d. Decreased sink rate

Last Answer : d. Decreased sink rate

Lowering the flaps during a landing approach: a. Increases the angle of descent without increasing the airspeed b. Decreases the angle of descent without increasing power c. Eliminates floating d. Permits approaches at a higher indicated airspeed

Description : Lowering the flaps during a landing approach: a. Increases the angle of descent without increasing the airspeed b. Decreases the angle of descent without increasing power c. Eliminates floating d. Permits approaches at a higher indicated airspeed

Last Answer : a. Increases the angle of descent without increasing the airspeed

An aircraft is travelling at 120 kts, what angle of bank would be required for a rate 1(one) turn? a. 30° b. 12° c. 18° d. 35°

Description : An aircraft is travelling at 120 kts, what angle of bank would be required for a rate 1(one) turn? a. 30° b. 12° c. 18° d. 35°

Last Answer : c. 18°

To crash a schedule you should: 1. Increase the time allowed on those tasks that have float. 2. Try to increase expenditures of time only those tasks that are behind schedule. 3. Replace those worker that are not performing up to par with the busy. 4. Increase work efforts on those tasks that are on the critical path.

Description : To crash a schedule you should: 1. Increase the time allowed on those tasks that have float.  2. Try to increase expenditures of time only those tasks that are behind schedule.  3. Replace those ... to par with the busy.  4. Increase work efforts on those tasks that are on the critical path.

Last Answer : 4. Increase work efforts on those tasks that are on the critical path.

What do three green lights represent when the landing gear is selected down? a. The gear is down b. The gear is down and locked c. The gear and doors are down and locked d. The gear is travelling between up and down

Description : What do three green lights represent when the landing gear is selected down? a. The gear is down b. The gear is down and locked c. The gear and doors are down and locked d. The gear is travelling between up and down

Last Answer : b. The gear is down and locked

A stall warning device must be set to operate: a. At the stalling speed b. At a speed just below the stalling speed c. At a speed about 5% to 10% above the stalling speed d. At a speed about 20% above the stalling speed

Description : A stall warning device must be set to operate: a. At the stalling speed b. At a speed just below the stalling speed c. At a speed about 5% to 10% above the stalling speed d. At a speed about 20% above the stalling speed

Last Answer : c. At a speed about 5% to 10% above the stalling speed

An aircraft is required to intercept and home to a VOR along the 064 radial. The OBS should be set to: a. 064 to get the correct needle sense and a TO indication b. 244 to get the correct needle sense and a TO indication c. 064 to get the correct needle sense and a FROM indication d. 244 to get the correct needle sense and a FROM indication

Description : An aircraft is required to intercept and home to a VOR along the 064 radial. The OBS should be set to: a. 064 to get the correct needle sense and a TO indication b. 244 to get the ... the correct needle sense and a FROM indication d. 244 to get the correct needle sense and a FROM indication

Last Answer : b. 244 to get the correct needle sense and a TO indication

An aircraft wishes to track a VOR along the 274 radial. If variation is 10° W, what should be set on the OBS? a. 274 b. 264 c. 094 d. 084

Description : An aircraft wishes to track a VOR along the 274 radial. If variation is 10° W, what should be set on the OBS? a. 274 b. 264 c. 094 d. 084

Last Answer : c. 094

When given instructions to set a mode/code, a pilot shall: a. Only use the word “wilco” b. Only read back the code c. Only use the word “roger” d. Read back mode and code

Description : When given instructions to set a mode/code, a pilot shall: a. Only use the word “wilco” b. Only read back the code c. Only use the word “roger” d. Read back mode and code

Last Answer : d. Read back mode and code

When does the engine High Pressure fuel shut off valve close? a. After a booster pump failure b. When the engine fuel switch is selected ‘ON’ during engine start c. When flight idle is selected d. When the engine fuel switch is selected ‘OFF’ during engine shut-down

Description : When does the engine High Pressure fuel shut off valve close? a. After a booster pump failure b. When the engine fuel switch is selected ‘ON’ during engine start c. When flight idle is selected d. When the engine fuel switch is selected ‘OFF’ during engine shut-down

Last Answer : d. When the engine fuel switch is selected ‘OFF’ during engine shut-down

How can the pilot increase the rate of turn and decrease the radius at the same time? a. Shallow the bank and increase airspeed b. Steeper bank and increase airspeed c. Steeper bank and decrease airspeed

Description : How can the pilot increase the rate of turn and decrease the radius at the same time? a. Shallow the bank and increase airspeed b. Steeper bank and increase airspeed c. Steeper bank and decrease airspeed

Last Answer : c. Steeper bank and decrease airspeed

If flaps are lowered during the take-off run: a. The lift would not change until the aircraft is airborne b. The lift would increase when the flaps are lowered c. The lift would decrease d. The acceleration would increase

Description : If flaps are lowered during the take-off run: a. The lift would not change until the aircraft is airborne b. The lift would increase when the flaps are lowered c. The lift would decrease d. The acceleration would increase

Last Answer : b. The lift would increase when the flaps are lowered

What is the recommended technique to counter the loss of airspeed and resultant lift from wind shear? a. Maintain, or increase, pitch attitude and accept the lower-than-normal airspeed indications b. Lower the pitch attitude and regain lost airspeed c. Avoid overstressing aircraft, pitch to stick shaker, and apply maximum power d. Accelerate the aircraft to prevent a stall by sacrificing altitude

Description : What is the recommended technique to counter the loss of airspeed and resultant lift from wind shear? a. Maintain, or increase, pitch attitude and accept the lower-than-normal airspeed ... shaker, and apply maximum power d. Accelerate the aircraft to prevent a stall by sacrificing altitude

Last Answer : c. Avoid overstressing aircraft, pitch to stick shaker, and apply maximum power

The purpose of a trim tab is: a. To assist the pilot in initiating movement of the controls b. To zero the load on the pilot controls in the flight attitude required c. To provide feel to the controls at high speed d. To increase the effectiveness of the controls

Description : The purpose of a trim tab is: a. To assist the pilot in initiating movement of the controls b. To zero the load on the pilot controls in the flight attitude required c. To provide feel to the controls at high speed d. To increase the effectiveness of the controls

Last Answer : b. To zero the load on the pilot controls in the flight attitude required

In the event of cabin depressurization, the actions of the pilot will be to: a. Immediately commence a diversion to a suitable alternate b. Increase engine power to provide additional airflow to the pressurization systems c. Maintain the aeroplane altitude to prevent further damage to the airframe by over loading of the structure d. Commence a descent to an altitude where the supplemental oxygen supply is sufficient for all crew and passengers

Description : In the event of cabin depressurization, the actions of the pilot will be to: a. Immediately commence a diversion to a suitable alternate b. Increase engine power to provide additional ... a descent to an altitude where the supplemental oxygen supply is sufficient for all crew and passengers

Last Answer : d. Commence a descent to an altitude where the supplemental oxygen supply is sufficient for all crew and passengers

An inversion is: a. A decrease of pressure with height b. A decrease of temperature with height c. An increase of temperature with height d. An increase of pressure with height

Description : An inversion is: a. A decrease of pressure with height b. A decrease of temperature with height c. An increase of temperature with height d. An increase of pressure with height

Last Answer : c. An increase of temperature with height

Generally, as altitude increases: a. Temperature decreases and density increases b. Temperature, pressure and density decreases c. Temperature and pressure increase and density decreases d. Temperature decreases and pressure and density increase

Description : Generally, as altitude increases: a. Temperature decreases and density increases b. Temperature, pressure and density decreases c. Temperature and pressure increase and density decreases d. Temperature decreases and pressure and density increase

Last Answer : b. Temperature, pressure and density decreases

The best strategies to increase stress tolerance are: a. Planning, experience and self-control (fewer unexpected situation) b. Learning, experience and anticipation c. Learning, experience and CRM d. Planning, experience and CRM

Description : The best strategies to increase stress tolerance are: a. Planning, experience and self-control (fewer unexpected situation) b. Learning, experience and anticipation c. Learning, experience and CRM d. Planning, experience and CRM

Last Answer : c. Learning, experience and CRM

The effects of carbon monoxide: a. Increases with altitude b. Decreases with altitude c. Increases with increase of density d. Decreases with pressure loss

Description : The effects of carbon monoxide: a. Increases with altitude b. Decreases with altitude c. Increases with increase of density d. Decreases with pressure loss

Last Answer : a. Increases with altitude

You are flying at a constant FL 290 and a constant mach number. The total temperature increases by 5°. The CAS will: a. Remain approximately constant b. Increase by 10 kts c. Decrease by 10 kts d. Will increase or decrease depending on whether you are above or below ISA

Description : You are flying at a constant FL 290 and a constant mach number. The total temperature increases by 5°. The CAS will: a. Remain approximately constant b. Increase by 10 kts c. Decrease by 10 kts d. Will increase or decrease depending on whether you are above or below ISA

Last Answer : a. Remain approximately constant

When does a pilot apply the limitations of the MEL? a. At parking before commencement of taxi b. Prior to take-off c. At any time in flight d. Any time up to coming to a complete stop and applying the parking brake

Description : When does a pilot apply the limitations of the MEL? a. At parking before commencement of taxi b. Prior to take-off c. At any time in flight d. Any time up to coming to a complete stop and applying the parking brake

Last Answer : d. Any time up to coming to a complete stop and applying the parking brake