To maintain altitude, what must be done as Indicated Airspeeed (IAS) is reduced? a. Decrease angle of attack to reduce the drag b. Increase angle of attack to maintain the correct lift force c. Deploy the speed brakes to increase drag d. Reduce thrust

To maintain altitude, what must be done as Indicated Airspeeed (IAS) is reduced?  
a. Decrease angle of attack to reduce the drag  
b. Increase angle of attack to maintain the correct lift force  
c. Deploy the speed brakes to increase drag  
d. Reduce thrust
by

1 Answer

Answer :

b. Increase angle of attack to maintain the correct lift force
by

Related questions

Which statement is true relative to changing angle of attack? a. A decrease in angle of attack will increase pressure below the wing and decrease drag b. An increase in angle of attack will decrease pressure below the wing and decrease drag c. An increase in angle of attack will increase drag d. An increase in angle of attack will decrease the lift coefficient

Description : Which statement is true relative to changing angle of attack? a. A decrease in angle of attack will increase pressure below the wing and decrease drag b. An increase in angle of attack will ... of attack will increase drag d. An increase in angle of attack will decrease the lift coefficient

Last Answer : c. An increase in angle of attack will increase drag

At a constant mass and altitude, a lower airspeed requires: a. More thrust and a lower coefficient of lift b. Less thrust and a lower coefficient of lift c. More thrust and a lower coefficient of drag d. A higher coefficient of lift

Description : At a constant mass and altitude, a lower airspeed requires: a. More thrust and a lower coefficient of lift b. Less thrust and a lower coefficient of lift c. More thrust and a lower coefficient of drag d. A higher coefficient of lift

Last Answer : d. A higher coefficient of lift

Shortly after take-off, the altitude of the aeroplane suffers an abrupt pitch-up and IAS rapidly decreases followed quickly by a decrease in altitude. Engine indications are normal. You should suspect what and what should you do? a. Marked temperature drop; apply full power b. Loss of head wind or an increase in tail wind; apply full power c. Incipient engine failure (ignore instruments); lower the nose to gain airspeed d. Local clear air turbulence; reduce speed to VRA and ride it out

Description : Shortly after take-off, the altitude of the aeroplane suffers an abrupt pitch-up and IAS rapidly decreases followed quickly by a decrease in altitude. Engine indications are normal. You should suspect what ... to gain airspeed d. Local clear air turbulence; reduce speed to VRA and ride it out

Last Answer : b. Loss of head wind or an increase in tail wind; apply full power

What flight condition should be expected when an aircraft leaves ground effect? a. A decrease in parasite drag permitting a lower angle of attack b. An increase induced drag and a requirement for a higher angle of attack c. An increase in dynamic stability d. A decrease in induced drag requiring a smaller angle of attack

Description : What flight condition should be expected when an aircraft leaves ground effect? a. A decrease in parasite drag permitting a lower angle of attack b. An increase induced drag and a requirement ... increase in dynamic stability d. A decrease in induced drag requiring a smaller angle of attack

Last Answer : b. An increase induced drag and a requirement for a higher angle of attack

By changing the angle of attack of a wing, the pilot can control the aeroplane’s: a. Lift and airspeed, but not drag b. Lift, gross weight and drag c. Lift, airspeed and drag d. Lift and drag, but not airspeed

Description : By changing the angle of attack of a wing, the pilot can control the aeroplane’s: a. Lift and airspeed, but not drag b. Lift, gross weight and drag c. Lift, airspeed and drag d. Lift and drag, but not airspeed

Last Answer : c. Lift, airspeed and drag

When does THRUST = DRAG? a. Climbing at a constant IAS b. Descending at a constant IAS c. Flying level at a constant IAS d. All of the above

Description : When does THRUST = DRAG? a. Climbing at a constant IAS b. Descending at a constant IAS c. Flying level at a constant IAS d. All of the above

Last Answer : c. Flying level at a constant IAS

Which statement is true regarding the opposing forces acting on an aeroplane in steady-state level flight? a. Thrust is greater than drag and weight and lift are equal b. These forces are equal c. Thrust is greater than drag and lift is greater than weight d. Thrust is slightly greater than lift, but the drag and weight are equal

Description : Which statement is true regarding the opposing forces acting on an aeroplane in steady-state level flight? a. Thrust is greater than drag and weight and lift are equal b. These forces are equal ... greater than weight d. Thrust is slightly greater than lift, but the drag and weight are equal

Last Answer : b. These forces are equal

What true airspeed and angle of attack should be used to generate the same amount of lift as altitude is increased? a. A higher true airspeed for any given angle of attack b. The same true airspeed and angle of attack c. A lower true airspeed and higher angle of attack d. A constant angle of attack and true airspeed

Description : What true airspeed and angle of attack should be used to generate the same amount of lift as altitude is increased? a. A higher true airspeed for any given angle of attack b. The same true ... c. A lower true airspeed and higher angle of attack d. A constant angle of attack and true airspeed

Last Answer : a. A higher true airspeed for any given angle of attack

What is the recommended technique to counter the loss of airspeed and resultant lift from wind shear? a. Maintain, or increase, pitch attitude and accept the lower-than-normal airspeed indications b. Lower the pitch attitude and regain lost airspeed c. Avoid overstressing aircraft, pitch to stick shaker, and apply maximum power d. Accelerate the aircraft to prevent a stall by sacrificing altitude

Description : What is the recommended technique to counter the loss of airspeed and resultant lift from wind shear? a. Maintain, or increase, pitch attitude and accept the lower-than-normal airspeed ... shaker, and apply maximum power d. Accelerate the aircraft to prevent a stall by sacrificing altitude

Last Answer : c. Avoid overstressing aircraft, pitch to stick shaker, and apply maximum power

If the angle of attack is increased beyond the critical angle of attack, the wing will no longer produce sufficient lift to support the weight of the aircraft: a. Unless the airspeed is greater than the normal stall speed b. Regardless of airspeed or pitch attitude c. Unless the pitch attitude is on or below the natural horizon d. In which case, the control column should be pulled-back immediately

Description : If the angle of attack is increased beyond the critical angle of attack, the wing will no longer produce sufficient lift to support the weight of the aircraft: a. Unless the airspeed is greater ... below the natural horizon d. In which case, the control column should be pulled-back immediately

Last Answer : b. Regardless of airspeed or pitch attitude

At a constant mass and altitude, a lower airspeed requires: a. More thrust and a lower coefficient of lift b. Less thrust and a lower coefficient of lift c. More thrust and a lower coefficient of drag d. A higher coefficient of lift

Description : At a constant mass and altitude, a lower airspeed requires: a. More thrust and a lower coefficient of lift b. Less thrust and a lower coefficient of lift c. More thrust and a lower coefficient of drag d. A higher coefficient of lift

Last Answer : d. A higher coefficient of lift

What factors affect descent angle in a glide? a. Configuration and altitude b. Configuration and angle of attack c. Mass and altitude d. Mass and configuration

Description : What factors affect descent angle in a glide? a. Configuration and altitude b. Configuration and angle of attack c. Mass and altitude d. Mass and configuration

Last Answer : b. Configuration and angle of attack

To recover from a spin, the elevators should be: a. Moved up to increase the angle of attack b. Moved down to reduce the angle of attack c. Set to neutral d. Allowed to float

Description : To recover from a spin, the elevators should be: a. Moved up to increase the angle of attack b. Moved down to reduce the angle of attack c. Set to neutral d. Allowed to float

Last Answer : b. Moved down to reduce the angle of attack

An aircraft is flying at constant indicated altitude over a warm airmass. The altimeter reading will be: a. Correct b. Greater than the real altitude c. Less than the real altitude d. Oscillating around the correct altitude

Description : An aircraft is flying at constant indicated altitude over a warm airmass. The altimeter reading will be: a. Correct b. Greater than the real altitude c. Less than the real altitude d. Oscillating around the correct altitude

Last Answer : c. Less than the real altitude

In the event of cabin depressurization, the actions of the pilot will be to: a. Immediately commence a diversion to a suitable alternate b. Increase engine power to provide additional airflow to the pressurization systems c. Maintain the aeroplane altitude to prevent further damage to the airframe by over loading of the structure d. Commence a descent to an altitude where the supplemental oxygen supply is sufficient for all crew and passengers

Description : In the event of cabin depressurization, the actions of the pilot will be to: a. Immediately commence a diversion to a suitable alternate b. Increase engine power to provide additional ... a descent to an altitude where the supplemental oxygen supply is sufficient for all crew and passengers

Last Answer : d. Commence a descent to an altitude where the supplemental oxygen supply is sufficient for all crew and passengers

Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to remain unchanged b. The propeller control regulates the engine RPM and in turn the propeller RPM c. A high blade angle, or increased pitch, reduces the propeller drag and allows more engine power for take-offs d. As the propeller control setting is changed by the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Description : Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to ... the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Last Answer : b. The propeller control regulates the engine RPM and in turn the propeller RPM

What is normally the most effective measure to reduce or avoid CAT effects? a. Change of flight level b. Change of course c. Increase of speed d. Decrease of speed

Description : What is normally the most effective measure to reduce or avoid CAT effects? a. Change of flight level b. Change of course c. Increase of speed d. Decrease of speed

Last Answer : a. Change of flight level

It is the unbalanced force developed in a turbo jet engine that is caused by the difference in the momentum of the low-velocity air entering the engine and the high velocity exhaust gases leaving the engine.  a. Fall  b. Lift  c. Drag  d. Thrust

Description : It is the unbalanced force developed in a turbo jet engine that is caused by the difference in the momentum of the low-velocity air entering the engine and the high velocity exhaust gases leaving the engine.  a. Fall  b. Lift  c. Drag  d. Thrust

Last Answer : Thrust

If flaps are lowered during the take-off run: a. The lift would not change until the aircraft is airborne b. The lift would increase when the flaps are lowered c. The lift would decrease d. The acceleration would increase

Description : If flaps are lowered during the take-off run: a. The lift would not change until the aircraft is airborne b. The lift would increase when the flaps are lowered c. The lift would decrease d. The acceleration would increase

Last Answer : b. The lift would increase when the flaps are lowered

If airbrakes are extended during a glide, and speed maintained, the rate of descent will: a. Increase and glide angle will be steeper b. Increase but glide angle will remain the same c. Decrease d. Remain the same

Description : If airbrakes are extended during a glide, and speed maintained, the rate of descent will: a. Increase and glide angle will be steeper b. Increase but glide angle will remain the same c. Decrease d. Remain the same

Last Answer : a. Increase and glide angle will be steeper

What action should be taken when, during an IFR flight in VMC, you suffer a radio failure? a. Return to the aerodrome from which you departed b. Continue flying in VMC and land as soon as possible c. Maintain your assigned altitude and land at the nearest aerodrome at which there are VMC conditions d. Continue flying at your assigned altitude and start your approach at your ETA

Description : What action should be taken when, during an IFR flight in VMC, you suffer a radio failure? a. Return to the aerodrome from which you departed b. Continue flying in VMC and land as ... there are VMC conditions d. Continue flying at your assigned altitude and start your approach at your ETA

Last Answer : b. Continue flying in VMC and land as soon as possible

If a CSD overheat warning is shown: a. The CSD can be disconnected and the pilot must control the alternator himself b. The pilot must throttle back to reduce the load on the alternator c. The CSD can be disconnected then reconnected later when the temperature has reduced d. The CSD can be disconnected but not used for the rest of the flight

Description : If a CSD overheat warning is shown: a. The CSD can be disconnected and the pilot must control the alternator himself b. The pilot must throttle back to reduce the load on the alternator c. The ... temperature has reduced d. The CSD can be disconnected but not used for the rest of the flight

Last Answer : d. The CSD can be disconnected but not used for the rest of the flight

The isobars drawn on a surface weather chart represent lines of equal pressure: a. At flight level b. At height of observatory c. At a determined density altitude d. Reduced to sea level

Description : The isobars drawn on a surface weather chart represent lines of equal pressure: a. At flight level b. At height of observatory c. At a determined density altitude d. Reduced to sea level

Last Answer : d. Reduced to sea level

Which stall has the greatest angle of attack? a. Low speed stall b. High speed stall (shock stall) c. Deep stall d. Accelerated stall

Description : Which stall has the greatest angle of attack? a. Low speed stall b. High speed stall (shock stall) c. Deep stall d. Accelerated stall

Last Answer : c. Deep stall

The angle of attack of a fixed pitch propeller: a. Depends on forward speed only b. Depends on forward speed and engine rotational speed c. Depends on engine rotational speed only d. Is constant for a fixed pitch propeller

Description : The angle of attack of a fixed pitch propeller: a. Depends on forward speed only b. Depends on forward speed and engine rotational speed c. Depends on engine rotational speed only d. Is constant for a fixed pitch propeller

Last Answer : b. Depends on forward speed and engine rotational speed

When does THRUST = DRAG? a. Climbing at a constant IAS b. Descending at a constant IAS c. Flying level at a constant IAS d. All of the above

Description : When does THRUST = DRAG? a. Climbing at a constant IAS b. Descending at a constant IAS c. Flying level at a constant IAS d. All of the above

Last Answer : c. Flying level at a constant IAS

A pilot suffering from decompression sickness should: a. Descend to a lower level where the symptoms will disappear and continue the flight at this or a lower level b. Decrease the cabin pressure to relieve the symptoms c. Continue the flight at a lower altitude and carry out exercises to relieve the pain in the affected site d. Land as soon as possible and seek medical assistance

Description : A pilot suffering from decompression sickness should: a. Descend to a lower level where the symptoms will disappear and continue the flight at this or a lower level b. Decrease the cabin pressure ... the pain in the affected site d. Land as soon as possible and seek medical assistance

Last Answer : d. Land as soon as possible and seek medical assistance

If a landing is to be made without flaps, the landing speed must be: a. reduced b. increased c. the same as for landing with flaps d. the same as for landing with flaps but with a steeper approach

Description : If a landing is to be made without flaps, the landing speed must be: a. reduced b. increased c. the same as for landing with flaps d. the same as for landing with flaps but with a steeper approach

Last Answer : b. increased

The method of alighting the aeroplane on water during a ditching is to: a. Carry out a normal approach with flaps and gear selected as normal but to calculate all speeds plus 10kts b. Reduce the approach angle to 1.5deg (150ft/mile), add 15kts to all speeds, keep the aeroplane clean (no flaps or gear) and fly it into the surface c. Fly a normal approach but keep the gear up and land at lowest possible speed with the nose raised for the tail to strike first d. Fly a normal approach to stalling speed and then drop the aeroplane vertically onto the water

Description : The method of alighting the aeroplane on water during a ditching is to: a. Carry out a normal approach with flaps and gear selected as normal but to calculate all speeds plus 10kts b. Reduce ... d. Fly a normal approach to stalling speed and then drop the aeroplane vertically onto the water

Last Answer : c. Fly a normal approach but keep the gear up and land at lowest possible speed with the nose raised for the tail to strike first

The advantage of a constant speed propeller over a fixed pitch propeller is: a. Higher maximum thrust available b. Higher maximum efficiency c. More blade surface area available d. Nearly maximum efficiency over wide speed range

Description : The advantage of a constant speed propeller over a fixed pitch propeller is: a. Higher maximum thrust available b. Higher maximum efficiency c. More blade surface area available d. Nearly maximum efficiency over wide speed range

Last Answer : d. Nearly maximum efficiency over wide speed range

The maximum induced drag occurs at a speed of: a. VMD b. VMP c. VSO d. VATO

Description : The maximum induced drag occurs at a speed of: a. VMD b. VMP c. VSO d. VATO

Last Answer : c. VSO

Lowering the flaps during a landing approach: a. Increases the angle of descent without increasing the airspeed b. Decreases the angle of descent without increasing power c. Eliminates floating d. Permits approaches at a higher indicated airspeed

Description : Lowering the flaps during a landing approach: a. Increases the angle of descent without increasing the airspeed b. Decreases the angle of descent without increasing power c. Eliminates floating d. Permits approaches at a higher indicated airspeed

Last Answer : a. Increases the angle of descent without increasing the airspeed

At an aircraft taxiing speed of 10mph, the anti-skid braking system is: a. Inoperative b. Operative c. Operative only on the nosewheel brakes d. Operative only on the main wheel brakes

Description : At an aircraft taxiing speed of 10mph, the anti-skid braking system is: a. Inoperative b. Operative c. Operative only on the nosewheel brakes d. Operative only on the main wheel brakes

Last Answer : a. Inoperative

An aircraft has a stalling speed in level flight of 70kt IAS. In a 60° balanced turn, the stalling speed would be: a. 76kt b. 84kt c. 99kt d. 140kt

Description : An aircraft has a stalling speed in level flight of 70kt IAS. In a 60° balanced turn, the stalling speed would be: a. 76kt b. 84kt c. 99kt d. 140kt

Last Answer : c. 99kt

The excess cabin altitude alerting system must operate to warn the crew at: a. 8,000ft b. 10,000ft c. 13,000ft d. 14,000ft

Description : The excess cabin altitude alerting system must operate to warn the crew at: a. 8,000ft b. 10,000ft c. 13,000ft d. 14,000ft

Last Answer : b. 10,000ft

Generally, as altitude increases: a. Temperature decreases and density increases b. Temperature, pressure and density decreases c. Temperature and pressure increase and density decreases d. Temperature decreases and pressure and density increase

Description : Generally, as altitude increases: a. Temperature decreases and density increases b. Temperature, pressure and density decreases c. Temperature and pressure increase and density decreases d. Temperature decreases and pressure and density increase

Last Answer : b. Temperature, pressure and density decreases

The effects of carbon monoxide: a. Increases with altitude b. Decreases with altitude c. Increases with increase of density d. Decreases with pressure loss

Description : The effects of carbon monoxide: a. Increases with altitude b. Decreases with altitude c. Increases with increase of density d. Decreases with pressure loss

Last Answer : a. Increases with altitude

The stalling speed of an aeroplane is most affected by: a. Changes in air density b. Variations in aeroplane loading c. Variations in flight altitude d. Changes in pitch attitude

Description : The stalling speed of an aeroplane is most affected by: a. Changes in air density b. Variations in aeroplane loading c. Variations in flight altitude d. Changes in pitch attitude

Last Answer : b. Variations in aeroplane loading

t higher elevation airports the pilot should know that indicated airspeed: a. will be unchanged but ground speed will be faster b. will be higher but ground speed will be unchanged c. should be increased to compensate for the thinner air d. should be higher to obtain a higher landing speed

Description : t higher elevation airports the pilot should know that indicated airspeed: a. will be unchanged but ground speed will be faster b. will be higher but ground speed will be unchanged c. should be increased to compensate for the thinner air d. should be higher to obtain a higher landing speed

Last Answer : a. will be unchanged but ground speed will be faster

What criteria determine which engine is the “critical” engine of a twin-engine aeroplane? a. The one with the center of thrust farthest from the centreline of the fuselage b. The one with the center of thrust closest to the centreline of the fuselage c. The one designated by the manufacturer which develops most usable thrust d. The failure of which causes the least yawing moment

Description : What criteria determine which engine is the critical engine of a twin-engine aeroplane? a. The one with the center of thrust farthest from the centreline of the fuselage b. The one ... the manufacturer which develops most usable thrust d. The failure of which causes the least yawing moment

Last Answer : b. The one with the center of thrust closest to the centreline of the fuselage

What phenomenon causes induced drag? a. Wing tip vortices b. Wing tanks c. The increased pressure at the leading edge

Description : What phenomenon causes induced drag? a. Wing tip vortices b. Wing tanks c. The increased pressure at the leading edge

Last Answer : a. Wing tip vortices

What effect does aspect ratio have on induced drag? a. Increased aspect ratio increases induced drag b. Increased aspect ratio reduces induced drag c. Changing aspect ratio has no effect on induced drag d. Induced drag will equal 1:3 x aspect ratio/chord ratio

Description : What effect does aspect ratio have on induced drag? a. Increased aspect ratio increases induced drag b. Increased aspect ratio reduces induced drag c. Changing aspect ratio has no effect on induced drag d. Induced drag will equal 1:3 x aspect ratio/chord ratio

Last Answer : b. Increased aspect ratio reduces induced drag

The best EAS/Drag ratio is approximately: a. 1.3 VMD b. 1.32 VMD c. 1.6 VMD d. 1.8 VMD

Description : The best EAS/Drag ratio is approximately: a. 1.3 VMD b. 1.32 VMD c. 1.6 VMD d. 1.8 VMD

Last Answer : b. 1.32 VMD

When approaching a wet runway, with the risk of hydroplaning, what technique should the pilot adapt? a. Positive touchdown, full reverse and brakes as soon as possible b. Smoothest possible touchdown, full reverse and only brakes below VP c. Positive touchdown, full reverse and only brakes below VP d. Normal landing, full reverse brakes at VP

Description : When approaching a wet runway, with the risk of hydroplaning, what technique should the pilot adapt? a. Positive touchdown, full reverse and brakes as soon as possible b. Smoothest possible ... touchdown, full reverse and only brakes below VP d. Normal landing, full reverse brakes at VP

Last Answer : c. Positive touchdown, full reverse and only brakes below VP

A marshaller crosses his/her hands in front of the face, palms outward and then moves the arms outwards. What does the signal indicate? a. Clear to move forward b. Brakes off c. Remove chocks d. Clear to close all engines

Description : A marshaller crosses his/her hands in front of the face, palms outward and then moves the arms outwards. What does the signal indicate? a. Clear to move forward b. Brakes off c. Remove chocks d. Clear to close all engines

Last Answer : c. Remove chocks

CAS is IAS corrected for: a. Position and instrument error b. Instrument, pressure, and density error c. Relative density only d. Compressibility

Description : CAS is IAS corrected for: a. Position and instrument error b. Instrument, pressure, and density error c. Relative density only d. Compressibility

Last Answer : a. Position and instrument error

An aircraft has to communicate with a VHF station at a range of 300nm, if the ground station is situated 2,500ft amsl, which of the following is the lowest altitude at which contact is likely to be made? a. 190ft b. 1,378ft c. 36,100ft d. 84,100ft

Description : An aircraft has to communicate with a VHF station at a range of 300nm, if the ground station is situated 2,500ft amsl, which of the following is the lowest altitude at which contact is likely to be made? a. 190ft b. 1,378ft c. 36,100ft d. 84,100ft

Last Answer : c. 36,100ft

Which constant pressure altitude chart is standard for a 30,065 ft pressure level (FL 300)? a. 200 hPa b. 700 hPa c. 500 hPa d. 300 hPa

Description : Which constant pressure altitude chart is standard for a 30,065 ft pressure level (FL 300)? a. 200 hPa b. 700 hPa c. 500 hPa d. 300 hPa

Last Answer : d. 300 hPa

You are cruising at FL 200, OAT is -40°C, sea level pressure is 1033 hPa. Calculate the true altitude. a. 20,660 ft b. 21,740 ft c. 18,260 ft d. 19, 340 ft

Description : You are cruising at FL 200, OAT is -40°C, sea level pressure is 1033 hPa. Calculate the true altitude. a. 20,660 ft b. 21,740 ft c. 18,260 ft d. 19, 340 ft

Last Answer : d. 19, 340 ft

How does a pilot react to heavy freezing rain at 2,000ft/AGL, when he is unable to deice nor land? a. He ascends to the cold air layer above b. He continues to fly at the same altitude c. He turns back before the aircraft loses maneuverability d. He descends to the warm air layer below

Description : How does a pilot react to heavy freezing rain at 2,000ft/AGL, when he is unable to deice nor land? a. He ascends to the cold air layer above b. He continues to fly at the same altitude c. He turns back before the aircraft loses maneuverability d. He descends to the warm air layer below

Last Answer : c. He turns back before the aircraft loses maneuverability