If airbrakes are extended during a glide, and speed maintained, the rate of descent will: a. Increase and glide angle will be steeper b. Increase but glide angle will remain the same c. Decrease d. Remain the same

If airbrakes are extended during a glide, and speed maintained, the rate of descent will:  
a. Increase and glide angle will be steeper  
b. Increase but glide angle will remain the same  
c. Decrease  
d. Remain the same
by

1 Answer

Answer :

a. Increase and glide angle will be steeper
by

Related questions

What factors affect descent angle in a glide? a. Configuration and altitude b. Configuration and angle of attack c. Mass and altitude d. Mass and configuration

Description : What factors affect descent angle in a glide? a. Configuration and altitude b. Configuration and angle of attack c. Mass and altitude d. Mass and configuration

Last Answer : b. Configuration and angle of attack

How can the pilot increase the rate of turn and decrease the radius at the same time? a. Shallow the bank and increase airspeed b. Steeper bank and increase airspeed c. Steeper bank and decrease airspeed

Description : How can the pilot increase the rate of turn and decrease the radius at the same time? a. Shallow the bank and increase airspeed b. Steeper bank and increase airspeed c. Steeper bank and decrease airspeed

Last Answer : c. Steeper bank and decrease airspeed

On an ILS approach, you are told that the weather has dropped below company minima. When must you abort the approach? a. Start of the glide-slope descent b. FAF c. Inner marker d. Outer marker

Description : On an ILS approach, you are told that the weather has dropped below company minima. When must you abort the approach? a. Start of the glide-slope descent b. FAF c. Inner marker d. Outer marker

Last Answer : d. Outer marker

What is the effect of deploying leading edge flaps? a. Increased minimum glide angle b. Decreased minimum glide angle c. Increased glide range d. Decreased sink rate

Description : What is the effect of deploying leading edge flaps? a. Increased minimum glide angle b. Decreased minimum glide angle c. Increased glide range d. Decreased sink rate

Last Answer : d. Decreased sink rate

If a landing is to be made without flaps, the landing speed must be: a. reduced b. increased c. the same as for landing with flaps d. the same as for landing with flaps but with a steeper approach

Description : If a landing is to be made without flaps, the landing speed must be: a. reduced b. increased c. the same as for landing with flaps d. the same as for landing with flaps but with a steeper approach

Last Answer : b. increased

To give the best obstacle clearance on take-off, take-off should be made with: a. Flaps partially extended and at best rate of climb speed (Vy) b. Flaps partially extended and at best angle of climb speed (Vx) c. Flaps retracted and at best rate of climb speed (Vy) d. Flaps retracted and at best angle of climb speed (Vx)

Description : To give the best obstacle clearance on take-off, take-off should be made with: a. Flaps partially extended and at best rate of climb speed (Vy) b. Flaps partially extended and at best angle of climb ... at best rate of climb speed (Vy) d. Flaps retracted and at best angle of climb speed (Vx)

Last Answer : d. Flaps retracted and at best angle of climb speed (Vx)

Lowering the flaps during a landing approach: a. Increases the angle of descent without increasing the airspeed b. Decreases the angle of descent without increasing power c. Eliminates floating d. Permits approaches at a higher indicated airspeed

Description : Lowering the flaps during a landing approach: a. Increases the angle of descent without increasing the airspeed b. Decreases the angle of descent without increasing power c. Eliminates floating d. Permits approaches at a higher indicated airspeed

Last Answer : a. Increases the angle of descent without increasing the airspeed

An aircraft is travelling at 100kts forward speed on a 3° glidescope. What is its rate of descent? a. 500 ft/min b. 300 ft/min c. 250 ft/min d. 600 ft/min

Description : An aircraft is travelling at 100kts forward speed on a 3° glidescope. What is its rate of descent? a. 500 ft/min b. 300 ft/min c. 250 ft/min d. 600 ft/min

Last Answer : a. 500 ft/min

If the weight of an aircraft is increased the maximum gliding range: a. Decreases b. Increases c. Remains the same, and rate of descent is unchanged d. Remains the same, but rate of descent increases

Description : If the weight of an aircraft is increased the maximum gliding range: a. Decreases b. Increases c. Remains the same, and rate of descent is unchanged d. Remains the same, but rate of descent increases

Last Answer : d. Remains the same, but rate of descent increases

When refuelling is being conducted with passengers embarking or disembarking: a. Refuelling is strictly prohibited whilst passengers are embarking or disembarking b. All flight crew must be on board c. Communications shall be maintained by ground crew and qualified crew on board d. The stairs shall be fully extended

Description : When refuelling is being conducted with passengers embarking or disembarking: a. Refuelling is strictly prohibited whilst passengers are embarking or disembarking b. All flight crew must be on board c. ... by ground crew and qualified crew on board d. The stairs shall be fully extended

Last Answer : c. Communications shall be maintained by ground crew and qualified crew on board

To maintain altitude, what must be done as Indicated Airspeeed (IAS) is reduced? a. Decrease angle of attack to reduce the drag b. Increase angle of attack to maintain the correct lift force c. Deploy the speed brakes to increase drag d. Reduce thrust

Description : To maintain altitude, what must be done as Indicated Airspeeed (IAS) is reduced? a. Decrease angle of attack to reduce the drag b. Increase angle of attack to maintain the correct lift force c. Deploy the speed brakes to increase drag d. Reduce thrust

Last Answer : b. Increase angle of attack to maintain the correct lift force

What factors affect descent angle in a glide? a. Configuration and altitude b. Configuration and angle of attack c. Mass and altitude d. Mass and configuration

Description : What factors affect descent angle in a glide? a. Configuration and altitude b. Configuration and angle of attack c. Mass and altitude d. Mass and configuration

Last Answer : b. Configuration and angle of attack

You are flying at a constant FL 290 and a constant mach number. The total temperature increases by 5°. The CAS will: a. Remain approximately constant b. Increase by 10 kts c. Decrease by 10 kts d. Will increase or decrease depending on whether you are above or below ISA

Description : You are flying at a constant FL 290 and a constant mach number. The total temperature increases by 5°. The CAS will: a. Remain approximately constant b. Increase by 10 kts c. Decrease by 10 kts d. Will increase or decrease depending on whether you are above or below ISA

Last Answer : a. Remain approximately constant

In the event of cabin depressurization, the actions of the pilot will be to: a. Immediately commence a diversion to a suitable alternate b. Increase engine power to provide additional airflow to the pressurization systems c. Maintain the aeroplane altitude to prevent further damage to the airframe by over loading of the structure d. Commence a descent to an altitude where the supplemental oxygen supply is sufficient for all crew and passengers

Description : In the event of cabin depressurization, the actions of the pilot will be to: a. Immediately commence a diversion to a suitable alternate b. Increase engine power to provide additional ... a descent to an altitude where the supplemental oxygen supply is sufficient for all crew and passengers

Last Answer : d. Commence a descent to an altitude where the supplemental oxygen supply is sufficient for all crew and passengers

Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to remain unchanged b. The propeller control regulates the engine RPM and in turn the propeller RPM c. A high blade angle, or increased pitch, reduces the propeller drag and allows more engine power for take-offs d. As the propeller control setting is changed by the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Description : Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to ... the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Last Answer : b. The propeller control regulates the engine RPM and in turn the propeller RPM

A precision Approach Procedure is defined as: a. An approach using bearing, elevation and distance information b. An approach with a crew of at least 2 pilots trained for such operations c. An instrument approach procedure utilizing azimuth and glide path information provided by an ILS or a PAR

Description : A precision Approach Procedure is defined as: a. An approach using bearing, elevation and distance information b. An approach with a crew of at least 2 pilots trained for such ... An instrument approach procedure utilizing azimuth and glide path information provided by an ILS or a PAR

Last Answer : c. An instrument approach procedure utilizing azimuth and glide path information provided by an ILS or a PAR

When would the negative differential limits be reached/exceeded? a. Rapid descent when AC descends below cabin altitude b. During ground pressure testing c. Rapid ascent when aircraft climbs d. When changing to manual operation

Description : When would the negative differential limits be reached/exceeded? a. Rapid descent when AC descends below cabin altitude b. During ground pressure testing c. Rapid ascent when aircraft climbs d. When changing to manual operation

Last Answer : a. Rapid descent when AC descends below cabin altitude

What flight condition should be expected when an aircraft leaves ground effect? a. A decrease in parasite drag permitting a lower angle of attack b. An increase induced drag and a requirement for a higher angle of attack c. An increase in dynamic stability d. A decrease in induced drag requiring a smaller angle of attack

Description : What flight condition should be expected when an aircraft leaves ground effect? a. A decrease in parasite drag permitting a lower angle of attack b. An increase induced drag and a requirement ... increase in dynamic stability d. A decrease in induced drag requiring a smaller angle of attack

Last Answer : b. An increase induced drag and a requirement for a higher angle of attack

Which statement is true relative to changing angle of attack? a. A decrease in angle of attack will increase pressure below the wing and decrease drag b. An increase in angle of attack will decrease pressure below the wing and decrease drag c. An increase in angle of attack will increase drag d. An increase in angle of attack will decrease the lift coefficient

Description : Which statement is true relative to changing angle of attack? a. A decrease in angle of attack will increase pressure below the wing and decrease drag b. An increase in angle of attack will ... of attack will increase drag d. An increase in angle of attack will decrease the lift coefficient

Last Answer : c. An increase in angle of attack will increase drag

The transition of altitude to flight level and vice versa is made: a. On the transition level in the climb and transition altitude in the descent b. At the transition altitude in the climb and transition level in the descent c. At the transition level only d. At the transition altitude only

Description : The transition of altitude to flight level and vice versa is made: a. On the transition level in the climb and transition altitude in the descent b. At the transition altitude in the climb and transition level in the descent c. At the transition level only d. At the transition altitude only

Last Answer : b. At the transition altitude in the climb and transition level in the descent

If cabin pressure is decreasing, the cabin VSI will indicate: a. Zero b. Climb c. Descent d. Reducing pressure

Description : If cabin pressure is decreasing, the cabin VSI will indicate: a. Zero b. Climb c. Descent d. Reducing pressure

Last Answer : b. Climb

When entering a steep turn, an IVSI is likely to show: a. No change in altitude b. A slight climb c. A slight descent d. A slight descent at high airspeed only

Description : When entering a steep turn, an IVSI is likely to show: a. No change in altitude b. A slight climb c. A slight descent d. A slight descent at high airspeed only

Last Answer : b. A slight climb

When is spark plug fouling most likely to occur? a. In the climb if you have not adjusted the mixture b. Cruise power c. In the descent if you have not adjusted the mixture d. Max take-off power

Description : When is spark plug fouling most likely to occur? a. In the climb if you have not adjusted the mixture b. Cruise power c. In the descent if you have not adjusted the mixture d. Max take-off power

Last Answer : a. In the climb if you have not adjusted the mixture

Shortly after take-off, the altitude of the aeroplane suffers an abrupt pitch-up and IAS rapidly decreases followed quickly by a decrease in altitude. Engine indications are normal. You should suspect what and what should you do? a. Marked temperature drop; apply full power b. Loss of head wind or an increase in tail wind; apply full power c. Incipient engine failure (ignore instruments); lower the nose to gain airspeed d. Local clear air turbulence; reduce speed to VRA and ride it out

Description : Shortly after take-off, the altitude of the aeroplane suffers an abrupt pitch-up and IAS rapidly decreases followed quickly by a decrease in altitude. Engine indications are normal. You should suspect what ... to gain airspeed d. Local clear air turbulence; reduce speed to VRA and ride it out

Last Answer : b. Loss of head wind or an increase in tail wind; apply full power

What is normally the most effective measure to reduce or avoid CAT effects? a. Change of flight level b. Change of course c. Increase of speed d. Decrease of speed

Description : What is normally the most effective measure to reduce or avoid CAT effects? a. Change of flight level b. Change of course c. Increase of speed d. Decrease of speed

Last Answer : a. Change of flight level

The method of alighting the aeroplane on water during a ditching is to: a. Carry out a normal approach with flaps and gear selected as normal but to calculate all speeds plus 10kts b. Reduce the approach angle to 1.5deg (150ft/mile), add 15kts to all speeds, keep the aeroplane clean (no flaps or gear) and fly it into the surface c. Fly a normal approach but keep the gear up and land at lowest possible speed with the nose raised for the tail to strike first d. Fly a normal approach to stalling speed and then drop the aeroplane vertically onto the water

Description : The method of alighting the aeroplane on water during a ditching is to: a. Carry out a normal approach with flaps and gear selected as normal but to calculate all speeds plus 10kts b. Reduce ... d. Fly a normal approach to stalling speed and then drop the aeroplane vertically onto the water

Last Answer : c. Fly a normal approach but keep the gear up and land at lowest possible speed with the nose raised for the tail to strike first

If flaps are lowered during the take-off run: a. The lift would not change until the aircraft is airborne b. The lift would increase when the flaps are lowered c. The lift would decrease d. The acceleration would increase

Description : If flaps are lowered during the take-off run: a. The lift would not change until the aircraft is airborne b. The lift would increase when the flaps are lowered c. The lift would decrease d. The acceleration would increase

Last Answer : b. The lift would increase when the flaps are lowered

An inversion is: a. A decrease of pressure with height b. A decrease of temperature with height c. An increase of temperature with height d. An increase of pressure with height

Description : An inversion is: a. A decrease of pressure with height b. A decrease of temperature with height c. An increase of temperature with height d. An increase of pressure with height

Last Answer : c. An increase of temperature with height

To recover from a spin, the elevators should be: a. Moved up to increase the angle of attack b. Moved down to reduce the angle of attack c. Set to neutral d. Allowed to float

Description : To recover from a spin, the elevators should be: a. Moved up to increase the angle of attack b. Moved down to reduce the angle of attack c. Set to neutral d. Allowed to float

Last Answer : b. Moved down to reduce the angle of attack

Which stall has the greatest angle of attack? a. Low speed stall b. High speed stall (shock stall) c. Deep stall d. Accelerated stall

Description : Which stall has the greatest angle of attack? a. Low speed stall b. High speed stall (shock stall) c. Deep stall d. Accelerated stall

Last Answer : c. Deep stall

If the angle of attack is increased beyond the critical angle of attack, the wing will no longer produce sufficient lift to support the weight of the aircraft: a. Unless the airspeed is greater than the normal stall speed b. Regardless of airspeed or pitch attitude c. Unless the pitch attitude is on or below the natural horizon d. In which case, the control column should be pulled-back immediately

Description : If the angle of attack is increased beyond the critical angle of attack, the wing will no longer produce sufficient lift to support the weight of the aircraft: a. Unless the airspeed is greater ... below the natural horizon d. In which case, the control column should be pulled-back immediately

Last Answer : b. Regardless of airspeed or pitch attitude

The angle of attack of a fixed pitch propeller: a. Depends on forward speed only b. Depends on forward speed and engine rotational speed c. Depends on engine rotational speed only d. Is constant for a fixed pitch propeller

Description : The angle of attack of a fixed pitch propeller: a. Depends on forward speed only b. Depends on forward speed and engine rotational speed c. Depends on engine rotational speed only d. Is constant for a fixed pitch propeller

Last Answer : b. Depends on forward speed and engine rotational speed

If the ailerons are deflected to 10°, compared to 5°, this will cause: a. An increased angle of bank b. An increased rate of roll c. No change to either bank angle or roll rate d. A reduction in the adverse yawing moment

Description : If the ailerons are deflected to 10°, compared to 5°, this will cause: a. An increased angle of bank b. An increased rate of roll c. No change to either bank angle or roll rate d. A reduction in the adverse yawing moment

Last Answer : b. An increased rate of roll

An aircraft is travelling at 120 kts, what angle of bank would be required for a rate 1(one) turn? a. 30° b. 12° c. 18° d. 35°

Description : An aircraft is travelling at 120 kts, what angle of bank would be required for a rate 1(one) turn? a. 30° b. 12° c. 18° d. 35°

Last Answer : c. 18°

An aircraft flying over the sea between 4500ft and 9000ft AMSL and outside CAS. To continue under VFR the meteorological conditions must remain: a. 2000ft horizontally and 1000ft vertically from cloud with visibility of 8km b. 1500m horizontally and 1000ft vertically from cloud with visibility of 5km c. 1500m horizontally and 1000m vertically from cloud with visibility of 5km d. Clear of cloud and in sight of the surface with visibility of 5km

Description : An aircraft flying over the sea between 4500ft and 9000ft AMSL and outside CAS. To continue under VFR the meteorological conditions must remain: a. 2000ft horizontally and 1000ft vertically from cloud with ... visibility of 5km d. Clear of cloud and in sight of the surface with visibility of 5km

Last Answer : b. 1500m horizontally and 1000ft vertically from cloud with visibility of 5km

How much fuel can be jettisoned? a. A specific amount b. The captain decides c. All d. A specified amount must remain

Description : How much fuel can be jettisoned? a. A specific amount b. The captain decides c. All d. A specified amount must remain

Last Answer : d. A specified amount must remain

What true airspeed and angle of attack should be used to generate the same amount of lift as altitude is increased? a. A higher true airspeed for any given angle of attack b. The same true airspeed and angle of attack c. A lower true airspeed and higher angle of attack d. A constant angle of attack and true airspeed

Description : What true airspeed and angle of attack should be used to generate the same amount of lift as altitude is increased? a. A higher true airspeed for any given angle of attack b. The same true ... c. A lower true airspeed and higher angle of attack d. A constant angle of attack and true airspeed

Last Answer : a. A higher true airspeed for any given angle of attack

The purpose of a trim tab is: a. To assist the pilot in initiating movement of the controls b. To zero the load on the pilot controls in the flight attitude required c. To provide feel to the controls at high speed d. To increase the effectiveness of the controls

Description : The purpose of a trim tab is: a. To assist the pilot in initiating movement of the controls b. To zero the load on the pilot controls in the flight attitude required c. To provide feel to the controls at high speed d. To increase the effectiveness of the controls

Last Answer : b. To zero the load on the pilot controls in the flight attitude required

A constant rate of climb in an aeroplane is determined by: a. Wind speed b. The aircraft weight c. Excess engine power d. Excess airspeed

Description : A constant rate of climb in an aeroplane is determined by: a. Wind speed b. The aircraft weight c. Excess engine power d. Excess airspeed

Last Answer : c. Excess engine power

Maximum endurance: a. Can be achieved in level unaccelerated flight with minimum fuel consumption b. Can be achieved by flying at the best rate of climb speed in straight and level flight c. Can be achieved in a steady climb d. Can be achieved by flying at the absolute ceiling

Description : Maximum endurance: a. Can be achieved in level unaccelerated flight with minimum fuel consumption b. Can be achieved by flying at the best rate of climb speed in straight and level flight c. Can be achieved in a steady climb d. Can be achieved by flying at the absolute ceiling

Last Answer : a. Can be achieved in level unaccelerated flight with minimum fuel consumption

By changing the angle of attack of a wing, the pilot can control the aeroplane’s: a. Lift and airspeed, but not drag b. Lift, gross weight and drag c. Lift, airspeed and drag d. Lift and drag, but not airspeed

Description : By changing the angle of attack of a wing, the pilot can control the aeroplane’s: a. Lift and airspeed, but not drag b. Lift, gross weight and drag c. Lift, airspeed and drag d. Lift and drag, but not airspeed

Last Answer : c. Lift, airspeed and drag

A pilot suffering from decompression sickness should: a. Descend to a lower level where the symptoms will disappear and continue the flight at this or a lower level b. Decrease the cabin pressure to relieve the symptoms c. Continue the flight at a lower altitude and carry out exercises to relieve the pain in the affected site d. Land as soon as possible and seek medical assistance

Description : A pilot suffering from decompression sickness should: a. Descend to a lower level where the symptoms will disappear and continue the flight at this or a lower level b. Decrease the cabin pressure ... the pain in the affected site d. Land as soon as possible and seek medical assistance

Last Answer : d. Land as soon as possible and seek medical assistance

At the alternate aerodrome, the commander of a turbojet engine aeroplane should have a fuel quantity (final reserve) sufficient for flying during: a. 30 minutes at holding flight speed at 1,500 ft b. 45 minutes at holding flight speed at 1,500 ft c. 30 minutes at cruising speed d. 45 minutes at cruising speed

Description : At the alternate aerodrome, the commander of a turbojet engine aeroplane should have a fuel quantity (final reserve) sufficient for flying during: a. 30 minutes at holding flight speed at 1,500 ft b. 45 ... speed at 1,500 ft c. 30 minutes at cruising speed d. 45 minutes at cruising speed

Last Answer : a. 30 minutes at holding flight speed at 1,500 ft

If a jet engine fails during take-off before V1: a. The take-off can be continued or aborted b. The take-off should be aborted c. The take-off should be continued d. The take-off may be continued if the aircraft speed is above VMCG and lies between VGO and VSTOP

Description : If a jet engine fails during take-off before V1: a. The take-off can be continued or aborted b. The take-off should be aborted c. The take-off should be continued d. The take-off may be continued if the aircraft speed is above VMCG and lies between VGO and VSTOP

Last Answer : b. The take-off should be aborted

Which of the following increases the stall angle? a. Slats b. Flaps c. Spoilers d. Ailerons

Description : Which of the following increases the stall angle? a. Slats b. Flaps c. Spoilers d. Ailerons

Last Answer : a. Slats

A pilot suffering from hyperventilation during final approach in poor weather can combat the effects by: a. Go on 100% oxygen and go around b. Land regardless of the weather c. Regulate depth and rate of breathing d. Declare a mayday

Description : A pilot suffering from hyperventilation during final approach in poor weather can combat the effects by: a. Go on 100% oxygen and go around b. Land regardless of the weather c. Regulate depth and rate of breathing d. Declare a mayday

Last Answer : c. Regulate depth and rate of breathing

. If a single tube pass heat exchanger is converted to two pass, then for the same flow rate, the pressure drop per unit length in tube side will (A) Increase by 1.8 times (B) Decrease by 2 2 (C) Increase by 2 16 (D) Remain unchanged

Description : . If a single tube pass heat exchanger is converted to two pass, then for the same flow rate, the pressure drop per unit length in tube side will (A) Increase by 1.8 times (B) Decrease by 2 2 (C) Increase by 2 16 (D) Remain unchanged

Last Answer : (C) Increase by 2 16

With increase in the shear rate, the apparent viscosity of pseudo-plastic fluids (A) Increases (B) Decreases (C) Remain same (D) May increase or decrease; depends on the magnitude of shear rate

Description : With increase in the shear rate, the apparent viscosity of pseudo-plastic fluids (A) Increases (B) Decreases (C) Remain same (D) May increase or decrease; depends on the magnitude of shear rate

Last Answer : (B) Decreases

A centrifugal pump used to pump water is used to pump an oil withspecific gravity of 0.8 at the same rate. The power consumption will now (A) Increase (B) Decrease (C) Remain same (D) Data insufficient to predict

Description : A centrifugal pump used to pump water is used to pump an oil withspecific gravity of 0.8 at the same rate. The power consumption will now (A) Increase (B) Decrease (C) Remain same (D) Data insufficient to predict

Last Answer : (B) Decrease