What effect does aspect ratio have on induced drag? a. Increased aspect ratio increases induced drag b. Increased aspect ratio reduces induced drag c. Changing aspect ratio has no effect on induced drag d. Induced drag will equal 1:3 x aspect ratio/chord ratio

What effect does aspect ratio have on induced drag?  
a. Increased aspect ratio increases induced drag  
b. Increased aspect ratio reduces induced drag  
c. Changing aspect ratio has no effect on induced drag  
d. Induced drag will equal 1:3 x aspect ratio/chord ratio
by

1 Answer

Answer :

b. Increased aspect ratio reduces induced drag
by

Related questions

Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to remain unchanged b. The propeller control regulates the engine RPM and in turn the propeller RPM c. A high blade angle, or increased pitch, reduces the propeller drag and allows more engine power for take-offs d. As the propeller control setting is changed by the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Description : Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to ... the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Last Answer : b. The propeller control regulates the engine RPM and in turn the propeller RPM

What phenomenon causes induced drag? a. Wing tip vortices b. Wing tanks c. The increased pressure at the leading edge

Description : What phenomenon causes induced drag? a. Wing tip vortices b. Wing tanks c. The increased pressure at the leading edge

Last Answer : a. Wing tip vortices

What flight condition should be expected when an aircraft leaves ground effect? a. A decrease in parasite drag permitting a lower angle of attack b. An increase induced drag and a requirement for a higher angle of attack c. An increase in dynamic stability d. A decrease in induced drag requiring a smaller angle of attack

Description : What flight condition should be expected when an aircraft leaves ground effect? a. A decrease in parasite drag permitting a lower angle of attack b. An increase induced drag and a requirement ... increase in dynamic stability d. A decrease in induced drag requiring a smaller angle of attack

Last Answer : b. An increase induced drag and a requirement for a higher angle of attack

The maximum induced drag occurs at a speed of: a. VMD b. VMP c. VSO d. VATO

Description : The maximum induced drag occurs at a speed of: a. VMD b. VMP c. VSO d. VATO

Last Answer : c. VSO

By changing the angle of attack of a wing, the pilot can control the aeroplane’s: a. Lift and airspeed, but not drag b. Lift, gross weight and drag c. Lift, airspeed and drag d. Lift and drag, but not airspeed

Description : By changing the angle of attack of a wing, the pilot can control the aeroplane’s: a. Lift and airspeed, but not drag b. Lift, gross weight and drag c. Lift, airspeed and drag d. Lift and drag, but not airspeed

Last Answer : c. Lift, airspeed and drag

Which statement is true relative to changing angle of attack? a. A decrease in angle of attack will increase pressure below the wing and decrease drag b. An increase in angle of attack will decrease pressure below the wing and decrease drag c. An increase in angle of attack will increase drag d. An increase in angle of attack will decrease the lift coefficient

Description : Which statement is true relative to changing angle of attack? a. A decrease in angle of attack will increase pressure below the wing and decrease drag b. An increase in angle of attack will ... of attack will increase drag d. An increase in angle of attack will decrease the lift coefficient

Last Answer : c. An increase in angle of attack will increase drag

The best EAS/Drag ratio is approximately: a. 1.3 VMD b. 1.32 VMD c. 1.6 VMD d. 1.8 VMD

Description : The best EAS/Drag ratio is approximately: a. 1.3 VMD b. 1.32 VMD c. 1.6 VMD d. 1.8 VMD

Last Answer : b. 1.32 VMD

Which statement is true regarding the opposing forces acting on an aeroplane in steady-state level flight? a. Thrust is greater than drag and weight and lift are equal b. These forces are equal c. Thrust is greater than drag and lift is greater than weight d. Thrust is slightly greater than lift, but the drag and weight are equal

Description : Which statement is true regarding the opposing forces acting on an aeroplane in steady-state level flight? a. Thrust is greater than drag and weight and lift are equal b. These forces are equal ... greater than weight d. Thrust is slightly greater than lift, but the drag and weight are equal

Last Answer : b. These forces are equal

During a slow decompression, passengers will occur: a. The cabin temperature will fall as pressure reduces b. Body cavities (sinuses, ears, etc.) will become pressurised and may require assistance in venting c. As soon as the pressure falls, the oxygen drop-out system will operate d. No contra effects, as slow decompression has no effect on the human body

Description : During a slow decompression, passengers will occur: a. The cabin temperature will fall as pressure reduces b. Body cavities (sinuses, ears, etc.) will become pressurised and may require assistance in ... will operate d. No contra effects, as slow decompression has no effect on the human body

Last Answer : b. Body cavities (sinuses, ears, etc.) will become pressurised and may require assistance in venting

To maintain altitude, what must be done as Indicated Airspeeed (IAS) is reduced? a. Decrease angle of attack to reduce the drag b. Increase angle of attack to maintain the correct lift force c. Deploy the speed brakes to increase drag d. Reduce thrust

Description : To maintain altitude, what must be done as Indicated Airspeeed (IAS) is reduced? a. Decrease angle of attack to reduce the drag b. Increase angle of attack to maintain the correct lift force c. Deploy the speed brakes to increase drag d. Reduce thrust

Last Answer : b. Increase angle of attack to maintain the correct lift force

At a constant mass and altitude, a lower airspeed requires: a. More thrust and a lower coefficient of lift b. Less thrust and a lower coefficient of lift c. More thrust and a lower coefficient of drag d. A higher coefficient of lift

Description : At a constant mass and altitude, a lower airspeed requires: a. More thrust and a lower coefficient of lift b. Less thrust and a lower coefficient of lift c. More thrust and a lower coefficient of drag d. A higher coefficient of lift

Last Answer : d. A higher coefficient of lift

When does THRUST = DRAG? a. Climbing at a constant IAS b. Descending at a constant IAS c. Flying level at a constant IAS d. All of the above

Description : When does THRUST = DRAG? a. Climbing at a constant IAS b. Descending at a constant IAS c. Flying level at a constant IAS d. All of the above

Last Answer : c. Flying level at a constant IAS

If the weight of an aircraft is increased the maximum gliding range: a. Decreases b. Increases c. Remains the same, and rate of descent is unchanged d. Remains the same, but rate of descent increases

Description : If the weight of an aircraft is increased the maximum gliding range: a. Decreases b. Increases c. Remains the same, and rate of descent is unchanged d. Remains the same, but rate of descent increases

Last Answer : d. Remains the same, but rate of descent increases

What is the effect of deploying leading edge flaps? a. Increased minimum glide angle b. Decreased minimum glide angle c. Increased glide range d. Decreased sink rate

Description : What is the effect of deploying leading edge flaps? a. Increased minimum glide angle b. Decreased minimum glide angle c. Increased glide range d. Decreased sink rate

Last Answer : d. Decreased sink rate

The minimum content of a readback of the message from ATC “X-CD CHANGE FREQUENCY TO STEPHENVILLE TOWER 118.7” is: a. 118.7 b. CHANGING FREQUENCY X-CD c. TO STEPHENVILLE X-CD d. 118.7 X-CD

Description : The minimum content of a readback of the message from ATC “X-CD CHANGE FREQUENCY TO STEPHENVILLE TOWER 118.7” is: a. 118.7 b. CHANGING FREQUENCY X-CD c. TO STEPHENVILLE X-CD d. 118.7 X-CD

Last Answer : d. 118.7 X-CD

A pressure head is subject to the following errors: a. Position, manoeuvre induced, temperature b. Position, manoeuvre induced c. Position, manoeuvre induced, density d. Position, manoeuvre induced, instrument

Description : A pressure head is subject to the following errors: a. Position, manoeuvre induced, temperature b. Position, manoeuvre induced c. Position, manoeuvre induced, density d. Position, manoeuvre induced, instrument

Last Answer : d. Position, manoeuvre induced, instrument

Disorientation is more likely when the pilot is: 1. flying in VMC 2. frequently changing between inside and outside references 3. flying from IMC to VMC 4. approaching over still water at night a. 1, 2 & 3 only are correct b. 1, 2 & 4 only are correct c. 1, 2, 3 & 4 are correct d. 1 only is correct

Description : Disorientation is more likely when the pilot is: 1. flying in VMC 2. frequently changing between inside and outside references 3. flying from IMC to VMC 4. approaching over still water at night a. 1, 2 & ... 1, 2 & 4 only are correct c. 1, 2, 3 & 4 are correct d. 1 only is correct

Last Answer : b. 1, 2 & 4 only are correct

When would the negative differential limits be reached/exceeded? a. Rapid descent when AC descends below cabin altitude b. During ground pressure testing c. Rapid ascent when aircraft climbs d. When changing to manual operation

Description : When would the negative differential limits be reached/exceeded? a. Rapid descent when AC descends below cabin altitude b. During ground pressure testing c. Rapid ascent when aircraft climbs d. When changing to manual operation

Last Answer : a. Rapid descent when AC descends below cabin altitude

If the ailerons are deflected to 10°, compared to 5°, this will cause: a. An increased angle of bank b. An increased rate of roll c. No change to either bank angle or roll rate d. A reduction in the adverse yawing moment

Description : If the ailerons are deflected to 10°, compared to 5°, this will cause: a. An increased angle of bank b. An increased rate of roll c. No change to either bank angle or roll rate d. A reduction in the adverse yawing moment

Last Answer : b. An increased rate of roll

If the angle of attack is increased beyond the critical angle of attack, the wing will no longer produce sufficient lift to support the weight of the aircraft: a. Unless the airspeed is greater than the normal stall speed b. Regardless of airspeed or pitch attitude c. Unless the pitch attitude is on or below the natural horizon d. In which case, the control column should be pulled-back immediately

Description : If the angle of attack is increased beyond the critical angle of attack, the wing will no longer produce sufficient lift to support the weight of the aircraft: a. Unless the airspeed is greater ... below the natural horizon d. In which case, the control column should be pulled-back immediately

Last Answer : b. Regardless of airspeed or pitch attitude

What true airspeed and angle of attack should be used to generate the same amount of lift as altitude is increased? a. A higher true airspeed for any given angle of attack b. The same true airspeed and angle of attack c. A lower true airspeed and higher angle of attack d. A constant angle of attack and true airspeed

Description : What true airspeed and angle of attack should be used to generate the same amount of lift as altitude is increased? a. A higher true airspeed for any given angle of attack b. The same true ... c. A lower true airspeed and higher angle of attack d. A constant angle of attack and true airspeed

Last Answer : a. A higher true airspeed for any given angle of attack

If a landing is to be made without flaps, the landing speed must be: a. reduced b. increased c. the same as for landing with flaps d. the same as for landing with flaps but with a steeper approach

Description : If a landing is to be made without flaps, the landing speed must be: a. reduced b. increased c. the same as for landing with flaps d. the same as for landing with flaps but with a steeper approach

Last Answer : b. increased

t higher elevation airports the pilot should know that indicated airspeed: a. will be unchanged but ground speed will be faster b. will be higher but ground speed will be unchanged c. should be increased to compensate for the thinner air d. should be higher to obtain a higher landing speed

Description : t higher elevation airports the pilot should know that indicated airspeed: a. will be unchanged but ground speed will be faster b. will be higher but ground speed will be unchanged c. should be increased to compensate for the thinner air d. should be higher to obtain a higher landing speed

Last Answer : a. will be unchanged but ground speed will be faster

Ingress of cold air in the furnaces through cracks, charging doors, openings etc(A) Reduces the flue gas temperature and makes the furnace atmosphereoxidising(B) Increases the load on the induced draft fan(C) Reduces the furnace draught(D) All (A), (B) and (C)

Description : Ingress of cold air in the furnaces through cracks, charging doors, openings etc (A) Reduces the flue gas temperature and makes the furnace atmosphere oxidising (B) Increases the load on the induced draft fan (C) Reduces the furnace draught (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A yaw damper: a. Increases rudder effectiveness b. Must be disengaged before making a turn c. Augments stability d. Increases the rate of yaw

Description : A yaw damper: a. Increases rudder effectiveness b. Must be disengaged before making a turn c. Augments stability d. Increases the rate of yaw

Last Answer : c. Augments stability

Which of the following increases the stall angle? a. Slats b. Flaps c. Spoilers d. Ailerons

Description : Which of the following increases the stall angle? a. Slats b. Flaps c. Spoilers d. Ailerons

Last Answer : a. Slats

In recovery from a spin: a. Ailerons should be kept neutral b. Airspeed increases c. Ailerons used to stop the spin d. Rudder and ailerons used against the direction of spin direction

Description : In recovery from a spin: a. Ailerons should be kept neutral b. Airspeed increases c. Ailerons used to stop the spin d. Rudder and ailerons used against the direction of spin direction

Last Answer : a. Ailerons should be kept neutral

Lowering the flaps during a landing approach: a. Increases the angle of descent without increasing the airspeed b. Decreases the angle of descent without increasing power c. Eliminates floating d. Permits approaches at a higher indicated airspeed

Description : Lowering the flaps during a landing approach: a. Increases the angle of descent without increasing the airspeed b. Decreases the angle of descent without increasing power c. Eliminates floating d. Permits approaches at a higher indicated airspeed

Last Answer : a. Increases the angle of descent without increasing the airspeed

Generally, as altitude increases: a. Temperature decreases and density increases b. Temperature, pressure and density decreases c. Temperature and pressure increase and density decreases d. Temperature decreases and pressure and density increase

Description : Generally, as altitude increases: a. Temperature decreases and density increases b. Temperature, pressure and density decreases c. Temperature and pressure increase and density decreases d. Temperature decreases and pressure and density increase

Last Answer : b. Temperature, pressure and density decreases

If you switch on the anti-collision light in IMC, what are the likely effects? a. Depth perception increases b. You can suffer from dizziness and disorientation c. You can suffer from Color Illusion d. Binocular vision is affected

Description : If you switch on the anti-collision light in IMC, what are the likely effects? a. Depth perception increases b. You can suffer from dizziness and disorientation c. You can suffer from Color Illusion d. Binocular vision is affected

Last Answer : b. You can suffer from dizziness and disorientation

The effects of carbon monoxide: a. Increases with altitude b. Decreases with altitude c. Increases with increase of density d. Decreases with pressure loss

Description : The effects of carbon monoxide: a. Increases with altitude b. Decreases with altitude c. Increases with increase of density d. Decreases with pressure loss

Last Answer : a. Increases with altitude

How is fuel consumption affect by the C of G position, in terms of ANM/kg? a. Increases with a forward C of G b. Decreases with an aft C of G c. Decreases with a forward C of G d. Fuel consumption is not affected by the C of G position

Description : How is fuel consumption affect by the C of G position, in terms of ANM/kg? a. Increases with a forward C of G b. Decreases with an aft C of G c. Decreases with a forward C of G d. Fuel consumption is not affected by the C of G position

Last Answer : c. Decreases with a forward C of G

You are flying at a constant FL 290 and a constant mach number. The total temperature increases by 5°. The CAS will: a. Remain approximately constant b. Increase by 10 kts c. Decrease by 10 kts d. Will increase or decrease depending on whether you are above or below ISA

Description : You are flying at a constant FL 290 and a constant mach number. The total temperature increases by 5°. The CAS will: a. Remain approximately constant b. Increase by 10 kts c. Decrease by 10 kts d. Will increase or decrease depending on whether you are above or below ISA

Last Answer : a. Remain approximately constant

Which of the following are all errors associated with ADF? a. Selective availability, coastal refraction, night effect b. Night effect, quadrantal error, lane slip c. Mountain effect, station interference, static interference d. Selective availability, coastal refraction, quadrantal error

Description : Which of the following are all errors associated with ADF? a. Selective availability, coastal refraction, night effect b. Night effect, quadrantal error, lane slip c. Mountain effect, station interference, static interference d. Selective availability, coastal refraction, quadrantal error

Last Answer : c. Mountain effect, station interference, static interference

How do misty/foggy conditions affect the pilot’s judgment on the approach? a. Underestimating range due to illusionary effect through the cockpit glass b. Underestimating range due to the lights appearing dim c. Overestimating range due to illusionary effect through the cockpit glass d. Overestimating range due to the lights appearing dim

Description : How do misty/foggy conditions affect the pilot's judgment on the approach? a. Underestimating range due to illusionary effect through the cockpit glass b. Underestimating range due to the ... to illusionary effect through the cockpit glass d. Overestimating range due to the lights appearing dim

Last Answer : d. Overestimating range due to the lights appearing dim

A sensation of tumbling and dizziness when a pilot makes movement of his/her head during a tight turn are symptoms of: a. The Occulogyral Effect b. Flicker-vertigo c. Pilot’s Vertigo d. Nystagmus

Description : A sensation of tumbling and dizziness when a pilot makes movement of his/her head during a tight turn are symptoms of: a. The Occulogyral Effect b. Flicker-vertigo c. Pilot’s Vertigo d. Nystagmus

Last Answer : c. Pilot’s Vertigo

An aircraft has a L/D ratio of 15:1 at 50kts in calm air. What would the L/D ratio be with a direct headwind of 25kts? a. 30:1 b. 15:1 c. 25:1 d. 7.5:1

Description : An aircraft has a L/D ratio of 15:1 at 50kts in calm air. What would the L/D ratio be with a direct headwind of 25kts? a. 30:1 b. 15:1 c. 25:1 d. 7.5:1

Last Answer : b. 15:1

To cover the greatest distance when gliding, the gliding speed must be: a. Near to the stalling speed b. As high as possible within VNE limits c. About 30% faster than Vmd d. The one that gives the highest L/D ratio

Description : To cover the greatest distance when gliding, the gliding speed must be: a. Near to the stalling speed b. As high as possible within VNE limits c. About 30% faster than Vmd d. The one that gives the highest L/D ratio

Last Answer : d. The one that gives the highest L/D ratio

Which of the following would give the greatest gliding performance? a. Flight at VMD b. Flight at 1.32VMD c. Flight at the best CL/CD ratio d. Flight close to CL MAX

Description : Which of the following would give the greatest gliding performance? a. Flight at VMD b. Flight at 1.32VMD c. Flight at the best CL/CD ratio d. Flight close to CL MAX

Last Answer : d. Flight close to CL MAX

How do you control power in a jet engine? a. By controlling the mixture ratio b. By controlling the fuel flow c. By controlling the airflow d. By controlling the bleed valves

Description : How do you control power in a jet engine? a. By controlling the mixture ratio b. By controlling the fuel flow c. By controlling the airflow d. By controlling the bleed valves

Last Answer : b. By controlling the fuel flow

The isobars drawn on a surface weather chart represent lines of equal pressure: a. At flight level b. At height of observatory c. At a determined density altitude d. Reduced to sea level

Description : The isobars drawn on a surface weather chart represent lines of equal pressure: a. At flight level b. At height of observatory c. At a determined density altitude d. Reduced to sea level

Last Answer : d. Reduced to sea level

If the track on an instrument departure is published, the pilot is expected to: a. Correct for the correct wind so as to stay within controlled airspace b. Ask ATC for another heading to steer correcting for wind c. Ignore the wind and proceed with a heading equal to the track d. Ask ATC for permission to correct heading for wind

Description : If the track on an instrument departure is published, the pilot is expected to: a. Correct for the correct wind so as to stay within controlled airspace b. Ask ATC for another heading to steer ... proceed with a heading equal to the track d. Ask ATC for permission to correct heading for wind

Last Answer : a. Correct for the correct wind so as to stay within controlled airspace

The maximum induced drag occurs at a speed of :

Description : The maximum induced drag occurs at a speed of :

Last Answer : VSO

The maximum induced drag occurs at a speed of: a. VMD b. VMP c. VSO d. VATO

Description : The maximum induced drag occurs at a speed of: a. VMD b. VMP c. VSO d. VATO

Last Answer : c. VSO

Has there been a steady decrease in the height of Greenland in the 20th Century? (a) Yes. (b) No. (c) The height has increased and decreased due to changing wind patterns. (d) Yes, because of dramatic increases in the calving rate of glacial ice into the surrounding ocean.

Description : Has there been a steady decrease in the height of Greenland in the 20th Century? (a) Yes. (b) No. (c) The height has increased and decreased due to changing wind patterns. (d) Yes, because of dramatic increases in the calving rate of glacial ice into the surrounding ocean.

Last Answer : (b) No

The reaction rate almost gets doubled for 10°C rise in temperature. This is due to the fact that the (A) Increased temperature reduces the activation energy (B) Fraction of molecules having threshold energy increases (C) Collision frequency increases (D) Value of threshold energy decreases

Description : The reaction rate almost gets doubled for 10°C rise in temperature. This is due to the fact that the (A) Increased temperature reduces the activation energy (B) Fraction of molecules having threshold energy increases (C) Collision frequency increases (D) Value of threshold energy decreases

Last Answer : (B) Fraction of molecules having threshold energy increases

When percentage of mica present in sand is large, it (a) Reduces the strength of mortar, or concrete (b) Increases the strength of mortar or concrete (c) Has no effect on mortar, or concrete strength (d) Enhances the strength of mortar, or concrete, but only marginally

Description : When percentage of mica present in sand is large, it (a) Reduces the strength of mortar, or concrete (b) Increases the strength of mortar or concrete (c) Has no effect on mortar, or concrete strength (d) Enhances the strength of mortar, or concrete, but only marginally

Last Answer : (c) Has no effect on mortar, or concrete strength

A tariff------ (a) Increases the volume of trade. (b) Reduces the volume of trade. © Has no effect on the volume of trade. (d) Both (a) and (c).

Description : A tariff------ (a) Increases the volume of trade. (b) Reduces the volume of trade. © Has no effect on the volume of trade. (d) Both (a) and (c).

Last Answer : (b) Reduces the volume of trade.