Which of the following defects is usually associated with the MAG GMAW) welding process when using Dip Transfer? a) Centerline cracking b) Lack of side wall Fusion c) Undercut d) Tungsten inclusions

Which of the following defects is usually associated with the MAG GMAW) welding process when using Dip  Transfer?  
a) Centerline cracking b) Lack of side wall Fusion c) Undercut d) Tungsten inclusions
by

1 Answer

Answer :

b) Lack of side wall Fusion
by

Related questions

Which of the following uses a flat characteristic? a) MAG (GMAW) b) Oxy-fuel gas welding c) Resistance spot welding d) SAW using greater than 1000 amps

Description : Which of the following uses a flat characteristic? a) MAG (GMAW) b) Oxy-fuel gas welding c) Resistance spot welding d) SAW using greater than 1000 amps

Last Answer : a) MAG (GMAW)

Which of the following defects are unlikely to be detected by normal radiographic technique? a) Intergranular corrosion cracking b) Porosity c) Slag d) Lack of penetration

Description : Which of the following defects are unlikely to be detected by normal radiographic technique? a) Intergranular corrosion cracking b) Porosity c) Slag d) Lack of penetration

Last Answer : a) Intergranular corrosion cracking

What is the mode of metal transfer for the TIG (GTAW) welding process? a) Spray Transfer b) Globular Transfer c) Dip Transfer d) None of the above

Description : What is the mode of metal transfer for the TIG (GTAW) welding process? a) Spray Transfer b) Globular Transfer c) Dip Transfer d) None of the above

Last Answer : d) None of the above

Why it is sometimes necessary to preheat the base material before welding? a) To remove oil and grease b) To remove moisture from inside the material c) To prevent the possible risk of cracking d) Not required if using cellulosic electrodes as these will provide enough heat

Description : Why it is sometimes necessary to preheat the base material before welding? a) To remove oil and grease b) To remove moisture from inside the material c) To prevent the possible risk of cracking d) Not required if using cellulosic electrodes as these will provide enough heat

Last Answer : c) To prevent the possible risk of cracking

Who should select the specific welds for NDT, to cover the 10% contractual percentage required by the specification/Code? a) Anyone can select the welds as its just a random choice b) The welder as he knows which welds are likely to produce the least defects c) This will be referenced in the inspection and test plan d) Nobody, as welding is always carried out to a high standard the use of percentage NDT is of no real value

Description : Who should select the specific welds for NDT, to cover the 10% contractual percentage required by the specification/Code? a) Anyone can select the welds as its just a random choice b) The welder ... welding is always carried out to a high standard the use of percentage NDT is of no real value

Last Answer : c) This will be referenced in the inspection and test plan

Why is it essential to clean the excess weld metal on completion of the production weld? a) So it can be ready for painting b) To remove any rust c) To ensure it is suitably clean for visual inspection and NDT d) To remove slag from the undercut

Description : Why is it essential to clean the excess weld metal on completion of the production weld? a) So it can be ready for painting b) To remove any rust c) To ensure it is suitably clean for visual inspection and NDT d) To remove slag from the undercut

Last Answer : c) To ensure it is suitably clean for visual inspection and NDT

In welder qualification testing of 45mm plates, why are side bends used instead of root and face bends? a) They are easier to produce b) The testing equipment cannot handle thick root/face bends c) Root defects are not important for welder qualification d) They give more accurate indications

Description : In welder qualification testing of 45mm plates, why are side bends used instead of root and face bends? a) They are easier to produce b) The testing equipment cannot handle thick root/face bends c) Root defects are not important for welder qualification d) They give more accurate indications

Last Answer : d) They give more accurate indications

In a fusion welding process, (a) only heat is used (b) only pressure is used (c) combination of heat and pressure is used (d) none of these

Description : In a fusion welding process, (a) only heat is used (b) only pressure is used (c) combination of heat and pressure is used (d) none of these

Last Answer : (a) only heat is used

X-rays can be used (1) for cutting and welding of metals. (2) to detect heart diseases. (3) to detect defects in precious stones and diamonds. (4) to detect gold under the earth.

Description : X-rays can be used (1) for cutting and welding of metals. (2) to detect heart diseases. (3) to detect defects in precious stones and diamonds. (4) to detect gold under the earth.

Last Answer : (3) to detect defects in precious stones and diamonds. Explanation: X-rays are used to detect and photograph defects of internal structure of a body such as metals, machine parts, cracks in wood ... , etc. They can reveal inhomogeneities- such as inclusions, lattice defects, etc in gems and stones.

X-rays can be used (1) for cutting and welding of metals. (2) to detect heart diseases. (3) to detect defects in precious stones and diamonds. (4) to detect gold under the earth.

Description : X-rays can be used (1) for cutting and welding of metals. (2) to detect heart diseases. (3) to detect defects in precious stones and diamonds. (4) to detect gold under the earth.

Last Answer : to detect defects in precious stones and diamonds.

Welding Defects

Description : Welding Defects 

Last Answer : Welding Defects  Welding defects Explanation and causes 1. Cracks Cracks occur when localized stresses exceed the ultimate tensile strength of material. These stresses are developed due to shrinkage ... Too fast a travel, Bad welding technique, Too great a heat build-up.

TIG welding, thoriated tungsten electrodes are used, because it (A) Has higher current carrying capacity (B) Has better electron emissivity (C) Is stronger than ordinary tungsten (D) Is easy to prepare

Description : TIG welding, thoriated tungsten electrodes are used, because it (A) Has higher current carrying capacity (B) Has better electron emissivity (C) Is stronger than ordinary tungsten (D) Is easy to prepare

Last Answer : Option B

The commonly used gases in tungsten arc welding are

Description : The commonly used gases in tungsten arc welding are 1.Hydrogen and oxygen 2.Hydrogen and organ 3.Hydrogen and helium 4.Helium and argon

Last Answer : The commonly used gases in tungsten arc welding are Helium and argon

Cold cracking in the heat affected zone of a high strength steel weld can take place because of the (A) Retained austenite (B) Martensite formation (C) Relatively high sulphur content in the base metal (D) Sufficient hydrogen present in the welding arc

Description : Cold cracking in the heat affected zone of a high strength steel weld can take place because of the (A) Retained austenite (B) Martensite formation (C) Relatively high sulphur content in the base metal (D) Sufficient hydrogen present in the welding arc

Last Answer : (B) Martensite formation

Lack of Glucocorticoids and mineral corticoids might be consequence of which of the following defects in the adrenal cortex? (A) Androstenadione deficiency (B) Estrone deficiency (C) 17 α-OH progesterone deficiency (D) C- α-Hydroxylase deficiency

Description : Lack of Glucocorticoids and mineral corticoids might be consequence of which of the following defects in the adrenal cortex? (A) Androstenadione deficiency (B) Estrone deficiency (C) 17 α-OH progesterone deficiency (D) C- α-Hydroxylase deficiency

Last Answer : Answer : D

First and the heaviest flower drop in fruit plants occurs due to : a. Structural defects in the flowers b. Lack of pollination c. Non fertilization d. All of the abov

Description : First and the heaviest flower drop in fruit plants occurs due to : a. Structural defects in the flowers b. Lack of pollination c. Non fertilization d. All of the abov

Last Answer : All of the abov

Exit Criteria may consist of :- i. Thoroughness measures , such as coverage of code, functionality or risk ii. Estimates of Defect density or reliability measures. iii. Residual risk such as defects not fixed or lack of test coverage in certain areas iv. Verifying the Test Environment. a) iv is correct and i,ii,iii are incorrect. b) i,ii,iii is correct and iv is incorrect c) ii is correct and i,ii,iii are incorrect d) iii and iv are correct and i,ii are incorrect

Description : Exit Criteria may consist of :- i. Thoroughness measures , such as coverage of code, functionality or risk ii. Estimates of Defect density or reliability measures. iii. Residual risk such as defects not fixed or ... correct and i,ii,iii are incorrect d) iii and iv are correct and i,ii are incorrect

Last Answer : b) i,ii,iii is correct and iv is incorrect

With which of the following NDE processes is it possible to detect both surface and slight subsurface defects up to 2mm below the surface a) Visual b) Dye Penetrant c) Magnetic Particle using DC d) Magnetic particle using AC

Description : With which of the following NDE processes is it possible to detect both surface and slight subsurface defects up to 2mm below the surface a) Visual b) Dye Penetrant c) Magnetic Particle using DC d) Magnetic particle using AC

Last Answer : c) Magnetic Particle using DC

what are the types of prokaryotic cell inclusions -Biology

Description : what are the types of prokaryotic cell inclusions -Biology

Last Answer : answer:

what are the types of prokaryotic cell inclusions -Biology

Description : what are the types of prokaryotic cell inclusions -Biology

Last Answer : answer:

What is inclusions?

Description : What is inclusions?

Last Answer : No

The fo l low ing substances are ce l l inclusions except (A) Melanin (B) Glycogen (C) Lipids (D) Centrosome

Description : The fo l low ing substances are ce l l inclusions except (A) Melanin (B) Glycogen (C) Lipids (D) Centrosome

Last Answer : D

What are cytoplasmic inclusions ?

Description : What are cytoplasmic inclusions ?

Last Answer : Cytoplasmic inclusions are cytoplasmic molecular aggregates, such as pigments, organic polymers and crystals. They are not considered cell organelles. Fat drops and glycogen granules are examples of cytoplasmic inclusions. Cell Structure Review - Image Diversity: cytoplasmic inclusions

This major protein component of connective tissue in mammals comprises most of the organic matter of skin, tendons, bones, and teeth, and occurs as fibrous inclusions in most other body structures. Is this material: a) elastin b) collagen c) fatty acids d) keratin

Description : This major protein component of connective tissue in mammals comprises most of the organic matter of skin, tendons, bones, and teeth, and occurs as fibrous inclusions in most other body structures. Is this material: a) elastin b) collagen c) fatty acids d) keratin

Last Answer : ANSWER: B -- collagen 

All welding processes require pressure along with heat. a) Yes b) No, fusion doesn’t require c) Can’t be stated d) None of the listed

Description : All welding processes require pressure along with heat. a) Yes b) No, fusion doesn’t require c) Can’t be stated d) None of the listed

Last Answer : b) No, fusion doesn’t require

The electric arc welding is a type of ............. welding. (a) forge (b) fusion

Description : The electric arc welding is a type of ............. welding. (a) forge (b) fusion

Last Answer : b) fusion

Late tapping will cause defect of? (i) Lack of fusion (Heat losses)* (ii) Piping defect (iii) kidney defect (iv) All above are correct

Description : Late tapping will cause defect of? (i) Lack of fusion (Heat losses)* (ii) Piping defect (iii) kidney defect (iv) All above are correct

Last Answer : (i) Lack of fusion (Heat losses)*

Late tapping will cause defect of? (i) Lack of fusion (Heat losses)* (ii) Piping defect (iii) Half moon defect (iv) None of above

Description : Late tapping will cause defect of? (i) Lack of fusion (Heat losses)* (ii) Piping defect (iii) Half moon defect (iv) None of above

Last Answer : (i) Lack of fusion (Heat losses)*

Defect of lack of fusion is mainly due to? (i) Improper heating.* (ii) Improper Gap (iii) Improper grinding (iv) None of above

Description : Defect of lack of fusion is mainly due to? (i) Improper heating.* (ii) Improper Gap (iii) Improper grinding (iv) None of above

Last Answer : (i) Improper heating.*

Which one of the following drugs, when used chronically, is associated with the development of bone pain and mineralization defects such as osteomalacia? (a) Calcitonin (b) Dihydrotachysterol (c) Ergocalciferol (d) Etidronate (e) Norgestrel

Description : Which one of the following drugs, when used chronically, is associated with the development of bone pain and mineralization defects such as osteomalacia? (a) Calcitonin (b) Dihydrotachysterol (c) Ergocalciferol (d) Etidronate (e) Norgestrel

Last Answer : Ans: D

Which of the following enzyme defects is associated with a characteristic body odour? 1) Phenylalanine aminotransferase 2) Galactose0-phosphate-uridyltransferase 3) Ornithine transcarbamylase deficiency 4) Fumaryl acetoacetase 5) Branched chain ketoacid decarboxylase

Description : Which of the following enzyme defects is associated with a characteristic body odour? 1) Phenylalanine aminotransferase 2) Galactose0-phosphate-uridyltransferase 3) Ornithine transcarbamylase deficiency 4) Fumaryl acetoacetase 5) Branched chain ketoacid decarboxylase

Last Answer : Answers-5 The following inborn errors of amino acid metabolism are associated with abnormal odours: Glutaric acidaemia type II (sweaty feet), hawkinsinuria (swimming pool), isovaleric acidaemia (sweaty feet), ... The general rule is that if a child smells peculiar he requires a metabolic work-up.

Megaloblast and Deficiency during preg- nancy is associated with birth defects such as neural tube defects are due to the deficiency of?

Description : Megaloblast and Deficiency during preg- nancy is associated with birth defects such as  neural tube defects are due to the deficiency  of?

Last Answer : Vitamin B9

Coverage based analysis is best described as: A. A metric used to show the logic covered during a test session providing insight to the extent of testing. B. A tool for documenting the unique combinations of conditions and associated results in order to derive unique test cases for validation testing. C. Tools for documenting defects as they are found during testing and for tracking their status through to resolution. D. The most traditional means for analyzing a system or a program

Description : Coverage based analysis is best described as: A. A metric used to show the logic covered during a test session providing insight to the extent of testing. B. A tool for documenting the unique ... their status through to resolution. D. The most traditional means for analyzing a system or a program

Last Answer : A. A metric used to show the logic covered during a test session providing insight to the extent of testing.

Long-term maintenance therapy with digoxin is the best option in the following category of CHF patients: A. Hypertensive patients B. Patients with hypertrophic cardiomyopathy C. Patients with associated atrial fibrillation D. Patients having cardiac valvular defects

Description : Long-term maintenance therapy with digoxin is the best option in the following category of CHF patients: A. Hypertensive patients B. Patients with hypertrophic cardiomyopathy C. Patients with associated atrial fibrillation D. Patients having cardiac valvular defects

Last Answer : C. Patients with associated atrial fibrillation

A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC+ve polarity, and a ROL:of 180mm per min. What would be the arc energy? a) Insufficient information given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Last Answer : d) 2.0 kJ/mm

What course of action should be taken upon finding a welder using incorrect shielding gas? a) Allow welding to proceed if the workmanship is good b) Report the incident and record all relevant information c) None if the tensile strength of the consumables is the same as the approved one d) Change the electrode for the correct type and continue welding

Description : What course of action should be taken upon finding a welder using incorrect shielding gas? a) Allow welding to proceed if the workmanship is good b) Report the incident and record all relevant ... the same as the approved one d) Change the electrode for the correct type and continue welding

Last Answer : b) Report the incident and record all relevant information

Who has the responsibility of ensuring the welder is using the correct polarity during welding? a) The welder and the welding inspector b) Store man and the welder c) Welding Engineer d) The Q/A department

Description : Who has the responsibility of ensuring the welder is using the correct polarity during welding? a) The welder and the welding inspector b) Store man and the welder c) Welding Engineer d) The Q/A department

Last Answer : a) The welder and the welding inspector

What is a typical ARC voltage setting when welding with the TIG (GTAW) process? a) 18-20V b) 24-26V c) 10-12V d) 70-90V

Description : What is a typical ARC voltage setting when welding with the TIG (GTAW) process? a) 18-20V b) 24-26V c) 10-12V d) 70-90V

Last Answer : c) 10-12V

A shorted armature coil in a DC motor can be detected by _____________. A. sparking at the brushes B. shiny armature coil C. worn grooves in the armature D. undercut mica

Description : A shorted armature coil in a DC motor can be detected by _____________. A. sparking at the brushes B. shiny armature coil C. worn grooves in the armature D. undercut mica

Last Answer : Answer: A

A megohmmeter can be used to test for ____________. A. an open field coil B. synchronous speed C. undercut mica D. reversed polarity

Description : A megohmmeter can be used to test for ____________. A. an open field coil B. synchronous speed C. undercut mica D. reversed polarity

Last Answer : Answer: A

A megohmmeter can be used to test for _____________. A. an open field coil B. a shorted field pole C. undercut mica D. reversed polarity

Description : A megohmmeter can be used to test for _____________. A. an open field coil B. a shorted field pole C. undercut mica D. reversed polarity

Last Answer : Answer: A

The Competitive Intelligence Officer a. thinks like the competitor by determining how that competitor measures success, looks to the future as to what the competition will do in the next year to two years, and evaluate how the competition can undercut your company’s performance. b. a competitor’s production position. c. monitors the competition on the production analysis portion of the Courier and evaluates the

Description : The Competitive Intelligence Officer a. thinks like the competitor by determining how that competitor measures success, looks to the future as to what the competition will do in the next year ... . c. monitors the competition on the production analysis portion of the Courier and evaluates the

Last Answer : a. thinks like the competitor by determining how that competitor measures success, looks to the future as to what the competition will do in the next year to two years, and evaluate how the competition can undercut your company’s performance.

Which of the following does not affect the elasticity of retentive clasp? A. Length of the arm B. The cross section shape C. The material used D. The undercut area

Description : Which of the following does not affect the elasticity of retentive clasp? A. Length of the arm B. The cross section shape C. The material used D. The undercut area

Last Answer : D. The undercut area

An occlusal approaching clasp TIP, A. Should occupy a predetermined undercut B. Contact the tooth under the survey line C. Rigid

Description : An occlusal approaching clasp TIP, A. Should occupy a predetermined undercut B. Contact the tooth under the survey line C. Rigid

Last Answer : B. Contact the tooth under the survey line

In the preparation of Premolar class I cavity what is the best way of getting retention, A. Slightly done undercut of the mesial and distal walls B. Slightly done undercut of the buccal and lingual walls C. The convergence of the cavity walls

Description : In the preparation of Premolar class I cavity what is the best way of getting retention, A. Slightly done undercut of the mesial and distal walls B. Slightly done undercut of the buccal and lingual walls C. The convergence of the cavity walls

Last Answer : B. Slightly done undercut of the buccal and lingual wall

How much undercut area should a clasp arm engage:** A. As much undercut as possible B. Anywhere beyond the survey line C. A predetermined amount of undercut

Description : How much undercut area should a clasp arm engage:** A. As much undercut as possible B. Anywhere beyond the survey line C. A predetermined amount of undercut

Last Answer : C. A predetermined amount of undercut

When all other removable partial denture considerations remain unchanged; clasps constructed of which material can engage the deepest undercut: A. Chrome cobalt casts B. Nickel chrome casts C. Wrought stainless steel (0,5mm) D. Wrought gold

Description : When all other removable partial denture considerations remain unchanged; clasps constructed of which material can engage the deepest undercut: A. Chrome cobalt casts B. Nickel chrome casts C. Wrought stainless steel (0,5mm) D. Wrought gold

Last Answer : D. Wrought gold