Description : What is a typical ARC voltage setting when welding with the TIG (GTAW) process? a) 18-20V b) 24-26V c) 10-12V d) 70-90V
Last Answer : c) 10-12V
Description : Explain TIG (GTAW) welding process with neat sketch.
Last Answer : Tungsten Inert Gas Arc Welding (TIG, GTAW): It is a welding process, in which heat is generated by an electric arc struck between a nonconsumable tungsten electrode and the work piece. The weld pool is ... produces a high quality weld of most of metals. Flux is not used in the process.
Description : Which of the following defects is usually associated with the MAG GMAW) welding process when using Dip Transfer? a) Centerline cracking b) Lack of side wall Fusion c) Undercut d) Tungsten inclusions
Last Answer : b) Lack of side wall Fusion
Description : TIG welding, thoriated tungsten electrodes are used, because it (A) Has higher current carrying capacity (B) Has better electron emissivity (C) Is stronger than ordinary tungsten (D) Is easy to prepare
Last Answer : Option B
Description : State the applications of TIG welding.
Last Answer : The applications of TIG welding are as follows: 1. Mostly used to weld aluminum and aluminum alloys. 2. It is used to weld stainless steel, carbon base alloy, copper base alloy, nickel base alloy etc. 3. It is used to welding dissimilar metals. 4. It is mostly used in aerospace industries.
Description : Globular form of cementite is formed during the __________ process. (A) Spheroidising (B) Hardening (C) Annealing (D) Normalising
Last Answer : (B) Hardening
Description : Diarrhoea like dirty water, from fruit or sour krout is seen in Options: 1) Cinchona 2) Croton tig. 3) Petroleum 4) Bryonia alba
Last Answer : Correct Answer: 4) Bryonia alba
Description : Differentiate between TIG and MIG.
Last Answer : Sr. No TIG MIG 1 In Tungsten Inert Gas arc welding, non- consumable tungsten electrode is used In Metal Inert Gas arc welding, consumable metallic electrode is used 2 ... penetration is obtained 8 Requires skilled operator Less skilled operator can do the job
Description : Which of the following work is done by General purpose Robot? A : Part drive B : Welding C : Spray picking D : Part panting
Last Answer : B : Welding
Description : Which of the following work is done by General purpose robot? (A) Part picking (B) Welding (C) Spray painting (D) All of the above
Last Answer : D
Description : Difference between fibrous proteins and globular proteins? -Biology
Last Answer : answer:
Description : Select the total number of false statement from the following (i) The globular head is an active ATPase enzyme and has binding sites for ATP and activ
Last Answer : Select the total number of false statement from the following (i) The globular head is an active ATPase enzyme and has ... arm A. 5 B. 4 C. 2 D. 1
Description : Where in the spiral galaxy you would expect to find globular clusters?
Last Answer : Need answer
Description : Many globular proteins are stable in solution although they lack in (A) Hydrogen bonds (B) Salt bonds (C) Non-polar bonds (D) Disulphide bonds
Last Answer : Answer : D
Description : A coiled structure in which peptide bonds are folded in regular manner by (A) Globular proteins (B) Fibrous proteins (C) Both (A) and (B) (D) None of these
Last Answer : Answer : A
Description : Globular proteins have completely folded, coiled polypeptide chain and the axial ratio (ratio of length to breadth) is (A) Less than 10 and generally not greater than 3–4 (B) Generally 10 (C) Greater than 10 and generally 20 (D) Greater than 10
Description : Many globular proteins are stable in solution inspite they lack in (A) Disulphide bonds (B) Hydrogen bonds (C) Salt bonds (D) Non polar bonds
Description : Collagen is (a) fibrous protein (b) globular protein (c) lipid (d) carbohydrate.
Last Answer : (a) fibrous protein
Description : The primary structure of a protein refers to : (a) whether the protein is fibrous or globular (b) the amino acid sequence in the polypeptide chain (c) the orientation of the amino acid side chains in space (d) the presence or absence of an α-helix
Last Answer : the amino acid sequence in the polypeptide chain
Description : What would be the most likely SAW flux type for welding medium carbon steel which requires impact testing: a) Cellulosic b) Rutile c) Fused d) Agglomerated
Last Answer : d) Agglomerated
Description : When welding medium carbon steel plates over 100mm in thickness would the basic electrodes require any pre treatment before use? a) None if they were in a vacuum pack opened 8 hours prior to use b) None if ... ) Heat to 500 °C for 2 hours if used outside d) Baked at 150°C for 4hours prior to use
Last Answer : b) None if they were in a sealed vacuum pack prior to use
Description : Which of the following uses a flat characteristic? a) MAG (GMAW) b) Oxy-fuel gas welding c) Resistance spot welding d) SAW using greater than 1000 amps
Last Answer : a) MAG (GMAW)
Description : When MMA welding what will be the effect on the weld f the power source was changed from AC to DC-ve? a) None b) Higher deposition rate c) It would slightly increase the depth of penetration d) The arc would become unstable
Last Answer : b) Higher deposition rate
Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm
Last Answer : d) 2.0 kJ/mm
Description : In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2
Last Answer : b) 333N/mm2
Description : Who should select the specific welds for NDT, to cover the 10% contractual percentage required by the specification/Code? a) Anyone can select the welds as its just a random choice b) The welder ... welding is always carried out to a high standard the use of percentage NDT is of no real value
Last Answer : c) This will be referenced in the inspection and test plan
Description : What information should be recorded as a minimum, on a completed production weld? a) Size and type of electrode and b) Welding supervisor’s name c) Welder’s Identification, date and weld number d) Welding inspectors name
Last Answer : c) Welder’s Identification, date and weld number
Description : Why is the OCV capped at voltage setting? a) To save electricity b) To prevent exploding of the consumable c) Allow smooth transition into welding voltage range d) To reduce the risk of fatality
Last Answer : c) Allow smooth transition into welding voltage range
Description : What course of action should be taken upon finding a welder using incorrect shielding gas? a) Allow welding to proceed if the workmanship is good b) Report the incident and record all relevant ... the same as the approved one d) Change the electrode for the correct type and continue welding
Last Answer : b) Report the incident and record all relevant information
Description : The welders have increased the voltage on the SAW welding set, what would be the effect on the weld appearance? a) No effect b) The weld width would be narrower c) The penetration will be increased d) The weld width would be wider
Last Answer : d) The weld width would be wider
Description : During root welding, which of the following would be the main cause of excess penetration? a) The root gap is too small in accordance with WPS b) Preheat not used c) The current is too high d) Root face is too large
Last Answer : c) The current is too high
Description : When would you measure the minimum preheat temperature? a) On completion of each pass b) Immediately prior to commencing the first pass and subsequent passes c) When the welding is ... preheat temperature measurement is only required if the heat input is lower than that specified in WPS
Last Answer : b) Immediately prior to commencing the first pass and subsequent passes
Description : Who has the responsibility of ensuring the welder is using the correct polarity during welding? a) The welder and the welding inspector b) Store man and the welder c) Welding Engineer d) The Q/A department
Last Answer : a) The welder and the welding inspector
Description : t is permissible to allow trainee welder to carry out production welding? a) Never b) Yes as long as the supervisor is happy with his workmanship standard c) Yes as long as he has the approved ... cover the intended scope of work d) Yes as long as no NDT is required on the finished weld
Last Answer : a) Never
Description : Who is responsible for site safety? a) Site Quality Engineer b) Welding Supervisor c) An approved safety engineer d) Everyone
Last Answer : d) Everyone
Description : What BSEN standard is used for welding symbols on drawings? a) BS EN 970 b) BS EN 287 c) BS EN 22553 d) BS EN 4515
Last Answer : c) BS EN 22553
Description : What does the term WPQR means? a) Weld productivity quality review b) Weld production quality requirments c) Welding procedure
Last Answer : c) Welding procedure
Description : Which of the following would not be required to be checked before welding? a) The welding consumables b) The welder qualification c) Calibration of the welding equipment d) The workshop humidity
Last Answer : d) The workshop humidity
Description : Why it is sometimes necessary to preheat the base material before welding? a) To remove oil and grease b) To remove moisture from inside the material c) To prevent the possible risk of cracking d) Not required if using cellulosic electrodes as these will provide enough heat
Last Answer : c) To prevent the possible risk of cracking
Description : Who determines what the correct weld preparation (root gap, root face, included angle) should be? a) The welding engineer b) The welding supervisor c) The welder will decide d) The inspector will recommend what is suitable
Last Answer : a) The welding engineer
Description : Who should have access to the WPQR’S? a) NDT operators b) Inspectors only c) Welders only d) Welding Engineer
Last Answer : d) Welding Engineer
Description : __________ column is the most suitable for achieving the best performance for mass transfer operations involving liquid with dispersed solids. (A) Wetted wall (B) Packed (C) Plate (D) Spray
Last Answer : C) Plate
Description : Measurement of the interfacial area of mass transfer is achieved easily & accurately in case of a __________ column. (A) Spray (B) Packed (C) Bubble cap plate (D) Wetted wall
Last Answer : (D) Wetted wall
Description : In arc welding, Argon is used because of its - (1) Low reactivity with metal (2) Ability to lower the melting point of the metal (3) High flammability (4) High calorific value
Last Answer : (1) Low reactivity with metal Explanation: In arc welding, Argon is used as a shielding gas because it is chemically inert and forms no compounds. At the high temperatures that welding requires, the ... to brittle welds and instability in the welding arc. So,argon and other inert gases are sprayed.
Description : In which case, molten metal is used to do welding? (i) Groove type (ii) spot type (iii) Plug type (iv) None
Last Answer : (iii) Plug type
Description : The displacement reaction between iron (III) oxide and a metal X is used for welding the rail tracks. Here X is: (a) Copper granules (b) Magnesium ribbon (c) Sodium pellets (d) Aluminum dust
Last Answer : (d) Aluminum dust
Description : Reaction of calcium carbide with water produces a gas, which is used (A) As an illuminant (B) For metal cutting/welding (C) Both (A) & (B) (D) Neither (A) nor (B)
Last Answer : (C) Both (A) & (B)
Description : Pick up the incorrect statement (A) The cross-sectional area of the welded member is effective (B) A welded joint develops strength of its parent metal (C) Welded joints provide rigidity (D) Welding takes more time than riveting
Last Answer : (D) Welding takes more time than riveting
Description : Cold cracking in the heat affected zone of a high strength steel weld can take place because of the (A) Retained austenite (B) Martensite formation (C) Relatively high sulphur content in the base metal (D) Sufficient hydrogen present in the welding arc
Last Answer : (B) Martensite formation