Description : ROM d) 8 bit, on chip 128 byte RAM. 3. After reset, SP register is initialized to address________. a) 8H b) 9H c) 7H d) 6H
Last Answer : c) 7H
Description : In 8051,After reset the SP register is initialized to address________. a. 8H b) 9H c) 7H
Description : SP of 8051 is of ___ wide and it is loaded with the default value of ___ after reset. a) 2 byte, 08H b) 8 bit, 07H c) 1 byte, 09H d) 8 bit, 06H
Last Answer : d) 8 bit, 06H
Description : In an 8085 microprocessor, the instruction CMP B has been executed while the contentsof accumulator is less than that of register B. As a result carry flag and zero flag will berespectively (A) set, reset (B) reset, set (C) reset, reset (D) set, set
Last Answer : (A) set, reset
Description : Name of typical dedicated register is: a. PC b. IR c. SP d. All of these
Last Answer : d. All of these
Description : The SP is of ___ wide register. And this may be defined anywhere in the ______. a) 8 byte, on-chip 128 byte RAM. b) 8 bit, on chip 256 byte RAM. c) 16 bit,
Last Answer : a) 8 byte, on-chip 128 byte RAM.
Description : What is the size of SP register in 8085 microprocessor? A) 16 bits B) 8 bits C) 64 bits D) 48 bits
Last Answer : What is the size of SP register in 8085 microprocessor? A) 16 bits B) 8 bits C) 64 bits D) 48 bits
Description : Which of the following is of type memory initialized Directive? i) DS ii) SET iii) DW iv) DBIT a) i, iii b) ii c) iii d) iv, ii
Last Answer : b) ii
Description : Which is not the control bus signal: a. READ b. WRITE c. RESET
Last Answer : c. RESET
Description : Serial port vector address is of _______. And causes an interrupt when ________. a) 0013H, either TI or RI flag is set b) 0023H, either TI or RI flag is reset c) 0013H, either TI or RI flag is reset d) 0023H, either TI or RI flag is set
Last Answer : a) 0013H, either TI or RI flag is set
Description : SP stand for: a. Stack pointer b. Stack pop c. Stack push d. None of these
Last Answer : a. Stack pointer
Description : SP stands for: a. Status pointer b. Stack pointer c. a and b d. None of these
Last Answer : b. Stack pointer
Description : Which of the following is of bit operations? i) SP ii) P2 iii) TMOD iv) SBUF v) IP a) ii, v only b) ii, iv, v only c) i, v only d) iii, ii only
Last Answer : c) i, v only
Description : What is the output of the following code PUSH AL a) Decrement SP by 2 & push a word to stack b) Increment SP by 2 & push a word to stack c) Decrement SP by 2 & push a AL to stack d) Illegal
Last Answer : b) Increment SP by 2 & push a word to stack
Last Answer : a) ii, v only
Description : In immediate addressing the operand is placed a. in the CPU register b. after OP code in the instruction c. in memory d. in stack
Last Answer : b. after OP code in the instruction
Description : List the allowed register pairs of 8085.
Last Answer : • B-C register pair • D-E register pair • H-L register pair
Description : Which is an integral part of any microcomputer system and its primary purpose is to hold program and data: a. Memory unit b. Register unit c. A and B d. None of these
Last Answer : a. Memory unit
Description : Which is the components of microprocessor: a. Register unit b. Arithmetic and logical unit c. Timing and control unit d. All of these
Description : The most common addressing techiniques employed by a CPU is a. immediate b. direct c. indirect d. register e. all of the above
Last Answer : e. all of the above
Description : A stack pointer is a. a 16-bit register in the microprocessor that indicate the beginning of the stack memory. b. a register that decodes and executes 16-bit arithmetic expression. c. The first memory location where a subroutine address is stored. d. a register in which flag bits are stored
Last Answer : a. a 16-bit register in the microprocessor that indicate the beginning of the stack memory.
Description : A stack is a. an 8-bit register in the microprocessor b. a 16-bit register in the microprocessor c. a set of memory locations in R/WM reserved for storing information temporarily during the execution of computer
Last Answer : c. a set of memory locations in R/WM reserved for storing information temporarily during the execution of computer
Description : Which of the following registers is used to keep track of address of the memory location where the next instruction is located? a. Memory Address Register b. Memory Data Register c. Instruction Register d. Program Register
Last Answer : d. Program Register
Description : A structure that stores a number of bits taken "together as a unit" is a a. gate b. mux c. decoder d. register
Last Answer : d. register
Description : Registers, which are partially visible to users and used to hold conditional, are known as a. PC b. Memory address registers c. General purpose register d. Flags
Last Answer : c. General purpose register
Description : Which of the following registers is used to keep track of address of the memory location where the next instruction is located? a. Memory address register b. Memory data register c. Instruction register d. Program counter
Last Answer : d. Program counter
Description : Which of the following registers is loaded with the contents of the memory location pointed by the PC? a. Memory address register b. Memory data register c. Instruction registers d. Program counter
Last Answer : c. Instruction registers
Description : CD-ROM a. Is a `semiconductor memory b. Memory register c. Magnetic memory d. None of the above
Last Answer : d. None of the above
Description : Interface electronic circuit is used to interconnect I/O devices to a computer’s CPU or a. ALU b. Memory c. Buffer d. Register
Last Answer : b. Memory
Description : A type of core store that has a lower access time than the devices used for working store in the same processor is known as a. Core memory b. Buffer c. Fast core d. Address register
Last Answer : d. Address register
Description : A set of information that defines the status of resources allocated to a process is a. Process control b. ALU c. Register Unit d. Process description
Last Answer : d. Process description
Description : The terminal device that functions as a cash register, computer terminal, and OCR reader is the: a. Data collection terminal b. OCR register terminal c. Video Display terminal d. POS terminal
Last Answer : d. POS terminal
Description : Which of the following registers is loaded with the contents of the memory location pointed by the PC? a. Memory address registers b. Memory data registers c. Instruction register d. Program counter
Last Answer : c. Instruction register
Description : CD-ROM is a a. Semiconductor memory b. Memory register c. Magnetic memory d. None of above
Last Answer : d. None of above
Description : The ____ place the data from a register onto the data bus: a. CPU b. ALU c. Both A and B d. None of these
Last Answer : a. CPU
Description : The information is transferred from the_____ and ____ specified register: a. MDR b. CPU c. Both A and B
Last Answer : c. Both A and B
Description : How many bit of MAR register: a. 8-bit b. 16-bit c. 32-bit d. 64-bit
Last Answer : b. 16-bit
Description : Which register is connected to the memory by way of the address bus: a. MAR b. MDR c. SAM d. None of these
Last Answer : a. MAR
Description : MDR stands for: a. Memory data register b. Memory data recode c. Micro data register d. None of these
Last Answer : a. Memory data register
Description : MAR stands for: a. Memory address register b. Memory address recode c. Micro address register d. None of these
Last Answer : a. Memory address register
Description : Which register is used to communicate with memory: a. MAR b. MDR c. Both A and B d. None of these
Description : Which latch is mostly used creating memory register: a. SR-Latch b. JK-Latch c. D-Latch d. T-Latch
Last Answer : c. D-Latch
Description : _____ a subsystem that transfer data between computer components inside a computer or between computer: a. Chip b. Register c. Processor d. Bus
Last Answer : d. Bus
Description : The 16 bit register is separated into groups of 4 bit where each groups is called: a. BCD b. Nibble c. Half byte d. None of these
Last Answer : b. Nibble
Description : Which is the important part of a combinational logic block: a. Index register b. Barrel shifter c. Both a & b d. None of these
Last Answer : b. Barrel shifter
Description : How many bit stored by status register: a. 1 bit b. 4 bit c. 6 bit d. 8 bit
Last Answer : a. 1 bit
Description : The processor uses the stack to keep track of where the items are stored on it this by using the: a. Stack pointer register b. Queue pointer register c. Both a & b d. None of these
Last Answer : a. Stack pointer register
Description : Which is used to store critical pieces of data during subroutines and interrupts: a. Stack b. Queue c. Accumulator d. Data register
Last Answer : a. Stack
Description : The status register is also called the____: a. Condition code register b. Flag register c. A and B d. None of these
Last Answer : c. A and B