The frequency of carrier in the carrier current pilot scheme is :

The frequency of carrier in the carrier current pilot scheme is :

(A) 1 kHz to 10 kHz

(B) 25 kHz to 50 kHz

(C) 10 kHz to 25 kHz

(D) 50 kHz to 500 kHz
by

1 Answer

Answer :

The frequency of carrier in the carrier current pilot scheme is : 50 kHz to 500 kHz

by

Related questions

Mention any two disadvantage of carrier current scheme for transmission line only.

Description : Mention any two disadvantage of carrier current scheme for transmission line only.

Last Answer : The program time (ie, the time taken by the carrier to reach the other end-upto .1% mile); the response time of band pass filter; capacitance phase-shift of the transmission line .

A 4 GHz carrier is amplitude modulated by a low-pass signal of maximum cut off frequency 1 MHz

Description : A 4 GHz carrier is amplitude modulated by a low-pass signal of maximum cut off frequency 1 MHz. lf this signal is to be ideally sampled, the minimum sampling frequency should be nearly

Last Answer : A 4 GHz carrier is amplitude modulated by a low-pass signal of maximum cut off frequency 1 MHz. lf this signal is to be ideally sampled, the minimum sampling frequency should be nearly 4 Ghz

Explain with neat sketch, the Pilot wire protection scheme applied to transmission line.

Description : Explain with neat sketch, the Pilot wire protection scheme applied to transmission line.

Last Answer : Pilot Wire Protection scheme of Transmission Line : Figure shows the single line diagram of Merz price voltage balance system for pilot wire protection of three phase transmission line. ... through the relay, which gives trip signal to the circuit breaker for protection of transmission line.

ECE Board Exam March 1996 The letter-number designation B8E is a form of modulation also known as ___________. A. pilot carrier system B. independent sideband emission C. lincomplex D. vestigial sideband transmission

Description : ECE Board Exam March 1996 The letter-number designation B8E is a form of modulation also known as ___________. A. pilot carrier system B. independent sideband emission C. lincomplex D. vestigial sideband transmission

Last Answer : B. independent sideband emission

The line trap unit employed in carrier current relaying: (A) offers high impedance to 50 Hz power frequency signal (B) offers high impedance to carrier frequency signal (C) offers low impedance to carrier frequency signal (D) Both (A) & (C)

Description : The line trap unit employed in carrier current relaying: (A) offers high impedance to 50 Hz power frequency signal (B) offers high impedance to carrier frequency signal (C) offers low impedance to carrier frequency signal (D) Both (A) & (C)

Last Answer : Ans: B The line trap unit employed in carrier current relaying offers high impedance to carrier frequency signal. Because carrier frequency range is 35 km – 500 kHz XL = 2Π f l Where f increases XL will also increases

In amplitude modulation scheme, the over-modulation

Description : In amplitude modulation scheme, the over-modulation (A) is desired phenomenon (B) helps in signal recovery (C) is undesired phenomenon (D) Envelope of AM maintains the shape of the baseband signal

Last Answer : In amplitude modulation scheme, the over-modulation is desired phenomenon

The total power of an AM transmitter having a carrier power of 50 W and the percentage of modulation at

Description : The total power of an AM transmitter having a carrier power of 50 W and the percentage of modulation at 80% is A) 50 W B) 66 W C) 68 W D) 70 W 

Last Answer : The total power of an AM transmitter having a carrier power of 50 W and the percentage of modulation at 80% is 66 W

If the radiated power of AM transmitter is 10 KW, the power in the carrier for modulation index of 0.6 is...

Description : If the radiated power of AM transmitter is 10 KW, the power in the carrier for modulation index of 0.6 is nearly:  (1) 8.24 KW (2) 9.26 KW (3) 8.47 KW (4) 9.6 KW

Last Answer : If the radiated power of AM transmitter is 10 KW, the power in the carrier for modulation index of 0.6 is nearly: 8.47 KW.

A good example of a pilot tone system used in commercial frequency modulation stations. A. FDM B. Time division C. Stereo multiplexing D. Frequency modulation

Description : A good example of a pilot tone system used in commercial frequency modulation stations. A. FDM B. Time division C. Stereo multiplexing D. Frequency modulation

Last Answer : C. Stereo multiplexing

In the event of an act of unlawful interference, which of the following is the correct procedure to be taken by the pilot in command? a. Squawk 7700 if the situation requires and continue the flight as per the ATC clearance received if possible b. Squawk 7500 and broadcast a warning to ATC other traffic on 121.500MHz or the frequency in use whilst maintaining the flight as cleared c. Squawk 7500 (or 7700 if required) and broadcast a warning if the situation forces deviation from the cleared flight plan d. If forced to deviate from the flight plan, climb or descend to altitudes that differ from the normal cruising altitudes by 1000ft

Description : In the event of an act of unlawful interference, which of the following is the correct procedure to be taken by the pilot in command? a. Squawk 7700 if the situation requires and continue ... the flight plan, climb or descend to altitudes that differ from the normal cruising altitudes by 1000ft

Last Answer : c. Squawk 7500 (or 7700 if required) and broadcast a warning if the situation forces deviation from the cleared flight plan

Which of the following is oldest multiplexing scheme? A. Frequency Division Multiplexing (FDM) B. Time Division Multiplexing (TDM) C. Code Division Multiplexing (CDM) D. Space Division Multiplexing (SDM)

Description : Which of the following is oldest multiplexing scheme? A. Frequency Division Multiplexing (FDM) B. Time Division Multiplexing (TDM) C. Code Division Multiplexing (CDM) D. Space Division Multiplexing (SDM)

Last Answer : D. Space Division Multiplexing (SDM)

Which of the following scheme is used by Bluetooth? a) Frequency hopping TDD scheme b) Frequency hopping FDD scheme c) DSSS TDD scheme d) DSSS FDD scheme

Description : Which of the following scheme is used by Bluetooth? a) Frequency hopping TDD scheme b) Frequency hopping FDD scheme c) DSSS TDD scheme d) DSSS FDD scheme

Last Answer : a) Frequency hopping TDD scheme

What is the effect of carrier frequency variation on AM signal?

Description : What is the effect of carrier frequency variation on AM signal?

Last Answer : Need answer

The carrier waves used for the radio transmission have frequency upto A. 15 KHz B. 30 KHz C. 90 KHz D. 150 KHz

Description : The carrier waves used for the radio transmission have frequency upto A. 15 KHz B. 30 KHz C. 90 KHz D. 150 KHz

Last Answer : ANSWER: B

What is meant by high frequency carrier gating?

Description : What is meant by high frequency carrier gating?

Last Answer : Thyristor is turned on by using a train of pulses from αto π. This type of signal is called as high frequency carrier gating.

How far is the visual carrier from the lowest frequency in the spectrum of a monochrome TV broadcast channel following the NTSC standard? A. 1.5 MHz B. 1.25 MHz C. 4.5 MHz D. 0.25 MHz

Description : How far is the visual carrier from the lowest frequency in the spectrum of a monochrome TV broadcast channel following the NTSC standard? A. 1.5 MHz B. 1.25 MHz C. 4.5 MHz D. 0.25 MHz

Last Answer : B. 1.25 MHz

What is the channel number of an FM station with a carrier frequency of 99.5 MHz? A. 256 B. 258 C. 257 D. 259

Description : What is the channel number of an FM station with a carrier frequency of 99.5 MHz? A. 256 B. 258 C. 257 D. 259

Last Answer : B. 258

____ system transmits frequency-division-multiplexed voice band signals over a coaxial cable for distances up to 4000 miles. A. T carrier B. X carrier C. L carrier D. F carrier

Description : ____ system transmits frequency-division-multiplexed voice band signals over a coaxial cable for distances up to 4000 miles. A. T carrier B. X carrier C. L carrier D. F carrier

Last Answer : C. L carrier

What is the carrier frequency of supergroup 10? A. 2724 kHz B. 2356 kHz C. 2108 kHz D. 3100 kHz

Description : What is the carrier frequency of supergroup 10? A. 2724 kHz B. 2356 kHz C. 2108 kHz D. 3100 kHz

Last Answer : D. 3100 kHz

What term is used to describe a spread spectrum communications system in which a very fast binary bit stream is used to shift the phase of an RF carrier? A. Frequency hopping B. Direct sequence C. Binary phase-shift keying D. Phase compandored spread spectrum

Description : What term is used to describe a spread spectrum communications system in which a very fast binary bit stream is used to shift the phase of an RF carrier? A. Frequency hopping B. Direct sequence C. Binary phase-shift keying D. Phase compandored spread spectrum

Last Answer : B. Direct sequence

What is the term used to describe a spread spectrum communications system where the center frequency if a conventional carrier is altered many time per second in accordance with a pseudo-random list of channels? A. Frequency hopping B. Direct sequence C. Time-domain frequency modulation D. Frequency compandored spread spectrum

Description : What is the term used to describe a spread spectrum communications system where the center frequency if a conventional carrier is altered many time per second in accordance with a pseudo ... hopping B. Direct sequence C. Time-domain frequency modulation D. Frequency compandored spread spectrum

Last Answer : A. Frequency hopping

What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Description : What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Last Answer : B. The ratio between the deviation of a frequency modulated signal and the modulating frequency.

What is meant by the term deviation ratio? A. The ratio of the audio modulating frequency to the center carrier frequency. B. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency. C. The ratio of the carrier center frequency to the audio modulating frequency. D. The ratio of the highest audio modulating frequency to the average audio modulating frequency.

Description : What is meant by the term deviation ratio? A. The ratio of the audio modulating frequency to the center carrier frequency. B. The ratio of the maximum carrier frequency deviation to the highest ... . D. The ratio of the highest audio modulating frequency to the average audio modulating frequency.

Last Answer : B. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

What is meant by the term deviation ratio? A. The ratio of the carrier center frequency to the audio modulating frequency B. The ratio of the highest audio modulating frequency to the average audio modulating frequency C. The ratio of the maximum carrier frequency deviation to the highest audio modulation frequency D. The ratio of the audio modulating frequency to the center carrier frequency

Description : What is meant by the term deviation ratio? A. The ratio of the carrier center frequency to the audio modulating frequency B. The ratio of the highest audio modulating frequency to the ... audio modulation frequency D. The ratio of the audio modulating frequency to the center carrier frequency

Last Answer : C. The ratio of the maximum carrier frequency deviation to the highest audio modulation frequency

This is referred to a product of simultaneous frequency and amplitude modulation or a carrier frequency variation which produces unwanted distortion. A. Absorption modulation B. Simultaneous modulation C. Dynamic instability D. Series modulation

Description : This is referred to a product of simultaneous frequency and amplitude modulation or a carrier frequency variation which produces unwanted distortion. A. Absorption modulation B. Simultaneous modulation C. Dynamic instability D. Series modulation

Last Answer : C. Dynamic instability

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Last Answer : A. Carrier power

Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Last Answer : C. Carrier power

A carrier signal has ______. A. Constant peak amplitude B. The information C. Frequency range 20-20000 Hz D. A varying amplitude

Description : A carrier signal has ______. A. Constant peak amplitude B. The information C. Frequency range 20-20000 Hz D. A varying amplitude

Last Answer : A. Constant peak amplitude

Which determines the number of sideband components of FM? A. Modulation frequency B. Modulation index C. Carrier frequency D. All of these

Description : Which determines the number of sideband components of FM? A. Modulation frequency B. Modulation index C. Carrier frequency D. All of these

Last Answer : B. Modulation index

What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz

Variation in amplitude or frequency of carrier wave is called A. amplitude modulation B. frequency modulation C. modulation D. bandwidth

Description : Variation in amplitude or frequency of carrier wave is called A. amplitude modulation B. frequency modulation C. modulation D. bandwidth

Last Answer : modulation

If frequency of modulated wave is less than frequency of carrier wave, then input signal is A. negative B. positive C. zero D. infinite

Description : If frequency of modulated wave is less than frequency of carrier wave, then input signal is A. negative B. positive C. zero D. infinite

Last Answer : negative

The _______ technique uses M different carrier frequencies that are modulated by the source signal. At one moment, the sign modulates one carrier frequency; at the next moment, thesignal modulates another carrier frequency. A) FDM B) DSSSC)FHSSD)TDM

Description : The _______ technique uses M different carrier frequencies that are modulated by the source signal. At one moment, the sign modulates one carrier frequency; at the next moment, thesignal modulates another carrier frequency. A) FDM B) DSSS C) FHSS D) TDM

Last Answer : FHSS

Which multiplexing technique shifts each signal to a different carrier frequency? A) FDM B) TDM C) Both (a)and (b) D) None of the above

Description : Which multiplexing technique shifts each signal to a different carrier frequency? A) FDM B) TDM C) Both (a)and (b) D) None of the above

Last Answer : FDM

In_______, the peakamplitude of one signal level is 0; the other is thesame as the amplitude of the carrier frequency. A) PSK B) OOK C) FSK D) none of the above

Description : In_______, the peakamplitude of one signal level is 0; the other is thesame as the amplitude of the carrier frequency. A) PSK B) OOK C) FSK D) none of the above

Last Answer : OOK

In_____ transmission, the frequency of the carrier signal is modulated to follow the changing voltage level (amplitude)of the modulating signal. The peak amplitude and phase of the carrier signal remainconstant,but as the amplitudeof the information signal changes, thefrequency of thecarrier changes correspondingly. A) AM B) PM C) FM D) none of the above

Description : In_____ transmission, the frequency of the carrier signal is modulated to follow the changing voltage level (amplitude)of the modulating signal. The peak amplitude and phase of the carrier signal remainconstant,but as ... of thecarrier changes correspondingly. A) AM B) PM C) FM D) none of the above

Last Answer : FM

In________, the amplitude of the carrier signal is varied to create signal elements. Both frequency and phase remainconstant. A) ASK B) PSK C) FSK D) QAM

Description : In________, the amplitude of the carrier signal is varied to create signal elements. Both frequency and phase remainconstant. A) ASK B) PSK C) FSK D) QAM

Last Answer : ASK

Given an AM radio signal with abandwidth of10 KHzand the highest-frequency component at 705 KHz, what is the frequency of the carrier signal? A) 700 KHz B) 705 KHz C) 710 KHz D) Cannot bedetermined from giveninformation

Description : Given an AM radio signal with abandwidth of10 KHzand the highest-frequency component at 705 KHz, what is the frequency of the carrier signal? A) 700 KHz B) 705 KHz C) 710 KHz D) Cannot bedetermined from giveninformation

Last Answer : 700 KHz

Carrier is A. One or more conductors that serve as a common connection for a related group of devices B. a continuous frequency capableof being modulated or impressed witha second signal C. the condition whentwo or more sections attempt to use the same channel at the same time D. a collection of interconnected functional units that provides a data communications service among stations attached tothe network E. None of the above

Description : Carrier is A. One or more conductors that serve as a common connection for a related group of devices B. a continuous frequency capableof being modulated or impressed witha second signal C. ... that provides a data communications service among stations attached tothe network E. None of the above

Last Answer : a continuous frequency capableof being modulated or impressed witha second signa

Geodimeter is based on: (A) Propagation of modulated light waves (B) Propagation of infrared radiation (C) The visible light as carrier with frequency of the order of 5 × 1014 Hz (D) High frequency radio waves

Description : Geodimeter is based on: (A) Propagation of modulated light waves (B) Propagation of infrared radiation (C) The visible light as carrier with frequency of the order of 5 × 1014 Hz (D) High frequency radio waves

Last Answer : Answer: Option A

Analog signals can be ________by combining them with a carrier frequency (A) Carried (B) Transported (C) Multiplexed (D) Mixed

Description : Analog signals can be ________by combining them with a carrier frequency (A) Carried (B) Transported (C) Multiplexed (D) Mixed

Last Answer : (C) Multiplexed

The ideal radar spectrum has what relationship to the carrier frequency?

Description : The ideal radar spectrum has what relationship to the carrier frequency?

Last Answer : Symmetrical above and below the carrier frequency.

What characteristic of a carrier wave is varied in frequency modulation?

Description : What characteristic of a carrier wave is varied in frequency modulation?

Last Answer : Instantaneous frequency.

An a.c. tachometer is just a ________with one phase excited from the carrier frequency. (A) two-phase A.C. servomotor (B) two-phase induction motor (C) A.C. operated universal motor (D) hybrid stepper motor.

Description : An a.c. tachometer is just a ________with one phase excited from the carrier frequency. (A) two-phase A.C. servomotor (B) two-phase induction motor (C) A.C. operated universal motor (D) hybrid stepper motor.

Last Answer : Ans: D This is a special purpose machine whose stator coil can be energized by electronically switched current.

What is the WAVELENGTH of the carrier wave, in meters, of a radio station which is broadcasting at a frequency of 100 megahertz?

Description : What is the WAVELENGTH of the carrier wave, in meters, of a radio station which is broadcasting at a frequency of 100 megahertz? 

Last Answer : ANSWER: 3 METERS

Inverse definite minimum time lag relay is also called ___________ (A) pilot relay. (B) differential relay. (C) over current relay. (D) directional overcurrent relay.

Description : Inverse definite minimum time lag relay is also called ___________ (A) pilot relay. (B) differential relay. (C) over current relay. (D) directional overcurrent relay.

Last Answer : Ans: B Inverse definite minimum time lag relay characteristic is inverse but minimum time is fixed. The operating time is inversely proportional to the magnitude of actuating quantity.

Reserve Bank announced the cap under Market Stabilisation Scheme (MSS) which has been fixed at Rs 30,000 crore for the current fiscal. MSS was launched in the year A) 2001 B) 2006 C) 2005 D) 2004 E) None of these

Description : Reserve Bank announced the cap under Market Stabilisation Scheme (MSS) which has been fixed at Rs 30,000 crore for the current fiscal. MSS was launched in the year A) 2001 B) 2006 C) 2005 D) 2004 E) None of these

Last Answer : D) 2004 Explanation: The scheme was launched in 2004.Under this scheme securities are issued with the objective of providing the RBI with a stock of securities with which it can intervene in the market for managing liquidity. These securities are issued not to meet the government‘s expenditure.

Under Liberalised Remittance Scheme, PAN card need not be insisted upon for remittance made towards permissible current account transactions up to __________ A. USD 25,000 B. USD 20,000 C. USD 15,000 D. USD 10,000 E. None of the Above

Description : Under Liberalised Remittance Scheme, PAN card need not be insisted upon for remittance made towards permissible current account transactions up to __________ A. USD 25,000 B. USD 20,000 C. USD 15,000 D. USD 10,000 E. None of the Above

Last Answer : A. USD 25,000 Explanation: PAN card need not be insisted upon for remittance made towards permissible current account transactions up to USD 25,000 per financial year.

A manufacturing industry plans to improve its energy performance under PAT through implementation of an energy conservation scheme. After implementation, calculate the Plant Energy Performance (PEP) with 2015-16 as the reference year. What is your inference? Given that:  The current year (2016-17 ) Annual Production – 28,750 T ,  Current year (2016-17 ) Annual Energy Consumption– 23,834 MWh,  Reference year (2015-16 ) production - 34,000 T,  Reference year (2015-16 ) Energy consumption - 27,200 MWh.

Description : A manufacturing industry plans to improve its energy performance under PAT through  implementation of an energy conservation scheme. After implementation, calculate the  Plant Energy Performance (PEP) with 2015-16 as the ... 34,000 T,   Reference year (2015-16 ) Energy consumption - 27,200 MWh.

Last Answer : Production factor (PF) = 28750/34000 = 0.846 …………………….1 mark Ref year equivalent energy (RYEE) = Ref Year Energy Use (RYEU) x PF   = 27,200 x 0.846= 23011MWh