Description : For minimum work input in a two stage compression process the intermediated pressure is the A. Arithmetic process of suction and discharge pressure B. Logarithmic mean of suction and discharge pressure C. Geometric mean of suction and discharge pressure D. Hyperbolic mean of suction and discharge
Last Answer : ANSWER : C
Description : Which portion of a sine-wave input is retained in the output of a series-negative limiter?
Last Answer : Positive.
Description : Which portion of a sine-wave input is retained in the output of a series-positive limiter?
Last Answer : Negative.
Description : What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?
Last Answer : -5 volts.
Description : In the basic transistor amplifier discussed earlier, what is the relationship between the polarity of the input and output signals?
Last Answer : The signals are opposite in polarity or 180 degrees out of phase with each other.
Description : Which transistor configuration provides a phase reversal between the input and output signals?
Last Answer : Common emitter.
Description : A two-input X-OR gate will produce a HIGH output when the inputs are at what logic levels?
Last Answer : . One or the other of the inputs must be HIGH, but not both at the same time.
Description : The input and output signals of a JFET amplifier have what phase relationship?
Last Answer : They are 180 degrees out of phase.
Description : In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?
Last Answer : 60 millivolts.
Description : In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?
Last Answer : 50 millivolts.
Description : select the correct response from the choices given in the parentheses. Q-20. In a closed-loop configuration the output signal is determined by (the input signal, the feedback signal, both).
Last Answer : Both the input signal and the feedback signal.
Description : If If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?
Last Answer : 200 millivolts.
Description : If the input signals are 180 degrees out of phase with each other, what will be the peak-to-peak amplitude of the output signals?
Last Answer : Each output signal will be 100 millivolts.
Description : If the input signals are in phase, what will be the peak-to peak amplitude of the output signals?
Last Answer : 0 volts (the input signals will "cancel out").
Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?
Last Answer : 200 millivolts. A-18. a. Differential amplifier
Description : If the differential amplifier is configured with a single input and differential outputs, what will the output signals be?
Last Answer : Each output will be a sine wave with a peak-to-peak amplitude of 100 millivolts. The output signals will be 180 degrees out of phase with each other.
Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?
Last Answer : . A different shape than the input signals but larger in amplitude.
Description : If only one input signal is used with a difference amplifier, what will the output signal be?
Last Answer : Equal in shape and frequency to the input signal; larger in amplitude than the input signal; half as large in amplitude as when two input signals were used that were 180 degrees out of phase.
Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?
Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than
Description : . If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?
Last Answer : No output (the signals will "cancel out").
Description : What two transistor amplifier configurations are combined in the single-transistor, two-input, single-output difference amplifier?
Last Answer : Common emitter (CE) and common base (CB)
Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.
Last Answer : An increase.
Description : When the input and output wipers of a balanced potentiometer are in the same angular position, what is the value of the error voltage?
Last Answer : Zero.
Description : What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?
Last Answer : Pulse width
Last Answer : Pulse width.
Description : If the inductance of a choke-input filter is increased, will the output ripple voltage amplitude (Er) increase or decrease?
Last Answer : Decrease.
Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease in the resistance of the regulating device.
Last Answer : Increase.
Description : Which type of optical splitter (Y-coupler or T-coupler) splits only a small amount of power from the input fiber to one of the output fibers?
Last Answer : T-coupler
Description : How are the input and output directional couplers in a twt connected to the helix?
Last Answer : The directional couplers are not physically connected to the helix.
Description : How does dc bias added to the input signal correct the distortion in the output signal?
Last Answer : The dc bias moves the input signal away from the step in the magnetism curve. This prevents the input signal from crossing the zero-point of the magnetism curve.
Description : The waveforms shown below are the input and output of an overdrive
Last Answer : a. Cutoff. b. Saturation.
Description : If the rf amplifier discussed has an 80 milliwatt input, what would be the maximum output?
Last Answer : 800 watts.
Description : What is the output Boolean expression for an AND gate with A and B as inputs when the B input is inverted?
Last Answer : AB
Description : In a properly functioning circuit, can both the input and output of an inverter be HIGH at the same time?
Last Answer : No.
Description : The input to an inverter is X + (YZ). What is the output
Last Answer : X + (YZ).
Description : What impedance relationship between the output of one circuit and the input of another circuit will provide the maximum power transfer?
Last Answer : Equal impedance.
Description : If the output of a circuit needs to be a complete representation of one-half of the input signal, what class of operation is indicated?
Last Answer : Class B operation.
Description : Power is __________. A. actual amount of power reference to 1mW B. logarithmic ratio of two powers C. definite amount of energy per time period D. current flow per time period
Last Answer : C. definite amount of energy per time period
Description : Which of the following statements are TRUE for damped vibrations? (P) . For a system having critical damping, the value of the damping ratio is unity and system does not undergo a vibratory motion. (Q) . Logarithmic decrement method ... Q only (B) P and S only (C) P, Q and R only (D) Q and S only
Last Answer : (C) P, Q and R only
Description : The ratio of the maximum displacement of the forced vibration to the deflection due to the static force, is known as A Damping factor B Damping coefficient C Logarithmic decrement D Magnification factor
Last Answer : D Magnification factor
Description : The ratio of the maximum displacement of the forced vibration to the deflection due to the static force is known as A Logarithmic decrement B Magnification factor C Damping factor D None of the mentioned
Last Answer : B Magnification factor
Description : The ratio of actual damping coefficient to the critical damping coefficient is known as A Magnification Factor B Damping Factor C Logarithmic decrementD None of the mentioned
Last Answer : B Damping Factor
Description : The ratio of maximum displacement of the forced vibration to the deflection due to the static force, is known as A. Damping FactorB. Damping Coefficient C. Logarithmic Decrement D. Magnification Factor
Last Answer : D. Magnification Factor
Description : The ratio of the maximum displacement of the forced vibration to the deflection due to the static force, is known as a) Damping factor b) Damping coefficient c) Logarithmic decrement d) Magnification factor
Last Answer : d) Magnification factor
Description : The ratio of the maximum displacement of the forced vibration to the deflection due to the static force is known as (A) damping factor (B) damping coefficient (C) logarithmic decrement (D) magnification factor
Last Answer : (D) magnification factor
Description : The ratio of the maximum displacement of the forced vibration to the deflection due to the static force, is known as a) damping factor b) damping coefficient c) logarithmic decrement d) magnification factor
Last Answer : d) magnification factor
Description : Why does adding dc vice ac bias voltage to the input signal result in a poor signal-to-noise ratio (SNR)?
Last Answer : With dc bias, the SNR is poor because only a small portion of the magnetism curve is straight enough to use, thus the output signal is weak compared with the natural tape hiss.
Description : The input impedance of your test equipment should exceed the impedance of the circuit under test by what ratio?
Last Answer : 10 to 1
Description : In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC
Last Answer : Answer: D
Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source
Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals