What is the preferred method for stripping wire?

What is the preferred method for stripping wire?
by

1 Answer

Answer :

By use of a wire-stripping tool
by

Related questions

What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Description : What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Last Answer : Adequate ventilation.

Why is flat tape preferred instead of round cord when wire bundles are laced?

Description : Why is flat tape preferred instead of round cord when wire bundles are laced?

Last Answer : Round cord has a tendency to cut into the wire insulation.

What stripping tool would NOT be used to strip glass braid insulation?

Description : What stripping tool would NOT be used to strip glass braid insulation?

Last Answer : Hot-blade stripper.

What is the preferred method of repairing cracked runs on boards?

Description : What is the preferred method of repairing cracked runs on boards?

Last Answer : Clinched staple.

What is the most preferred method of troubleshooting?

Description : What is the most preferred method of troubleshooting?

Last Answer : Testing components by comparison

In McCabe-Thiele method of theoretical plate calculation for a distillation column, the operating lines of stripping and rectifying sections coincide with the diagonal at __________ reflux. (A) Total (B) Minimum (C) Operating (D) Maximum permissible

Description : In McCabe-Thiele method of theoretical plate calculation for a distillation column, the operating lines of stripping and rectifying sections coincide with the diagonal at __________ reflux. (A) Total (B) Minimum (C) Operating (D) Maximum permissible

Last Answer : (A) Total

Pick out the correct statement. (A) The slope of the stripping line is always less than unity (B) For a given separation in a binary distillation column, with increase in reflux ratio (above the minimum reflux ratio), the fixed cost of the distillation column first increases and then decreases (C) In Ponchon-Savarit method of no. of theoretical plate determination, the stripping and rectifying operating lines are vertical at total reflux (D) Kremser-Brown-Souder's equation is used to calculate the efficiency of a plate tower

Description : Pick out the correct statement. (A) The slope of the stripping line is always less than unity (B) For a given separation in a binary distillation column, with increase in reflux ratio ( ... (D) Kremser-Brown-Souder's equation is used to calculate the efficiency of a plate tower

Last Answer : C) In Ponchon-Savarit method of no. of theoretical plate determination, the stripping and rectifying operating lines are vertical at total reflux

The best method of milking is— (A) Knuckling method (B) Fisting method (C) Stripping method (D) None of these

Description : The best method of milking is— (A) Knuckling method (B) Fisting method (C) Stripping method (D) None of these

Last Answer : (D) None of these

What type of deflection is preferred for a crt electron beam?

Description : What type of deflection is preferred for a crt electron beam?

Last Answer : . Electromagnetic.

Which types of LEDs are the preferred optical sources for short-distance, low-data-rate fiber optic systems?

Description : Which types of LEDs are the preferred optical sources for short-distance, low-data-rate fiber optic systems?

Last Answer : SLEDs and ELEDs.

Why are LEDs preferred over laser diodes for low- and moderate-frequency analog applications?

Description : Why are LEDs preferred over laser diodes for low- and moderate-frequency analog applications?

Last Answer : LEDs require less complex circuitry than lasers.

Extrinsic (OH) absorption peaks define three regions or windows of preferred operation. List the three windows of operation.

Description : Extrinsic (OH) absorption peaks define three regions or windows of preferred operation. List the three windows of operation.

Last Answer : The first, second, and third windows of operation are 850 nm, 1300 nm, and 1550 nm, respectively.

Why are drum-type armatures preferred over the Gramme ring armature in modern dc generators?

Description : Why are drum-type armatures preferred over the Gramme ring armature in modern dc generators?

Last Answer : Drum-type armatures are more efficient, because flux lines are cut by both sides of each coil.

Why is a multimeter preferred over separate meters?

Description : Why is a multimeter preferred over separate meters?

Last Answer : It is much more convenient to have one meter with several functions than several meters each with a single function.

To restore SOME color, can you dye your hair without stripping/bleaching it first?

Description : To restore SOME color, can you dye your hair without stripping/bleaching it first?

Last Answer : I don’t know your skill in doing it yourself, but some color could be streaked, no need to bleach.

Is the internet stripping us of humanity?

Description : Is the internet stripping us of humanity?

Last Answer : Finding joy in the suffering of others has been a near universal human core trait since the dawn of time.

why are crows stripping maytenus green showers tree

Description : why are crows stripping maytenus green showers tree

Last Answer : Need Answer

can I freeze corn on the cob without stripping the kernels?

Description : can I freeze corn on the cob without stripping the kernels?

Last Answer : How do I? ...Freeze Freezing Corn Preparation - Select only tender, freshly-gathered corn in the milk stage. Husk and trim the ears, remove silks and wash. Corn-on-the-cob - Water ... 11 minutes. Cool promptly and completely to prevent a "cobby" taste. Drain and package. Seal and freeze.

Bark is Stripping on Gardenia What could it be?

Description : Bark is Stripping on Gardenia What could it be?

Last Answer : Need Answer

design parking lot stripping

Description : design parking lot stripping

Last Answer : Depends on the state/town ordinance. Check with city/town hall.

What episode of Alfred Hitchcock presents features a stripping women at the monologue?

Description : What episode of Alfred Hitchcock presents features a stripping women at the monologue?

Last Answer : What is the answer ?

Varicose vein stripping?

Description : Varicose vein stripping?

Last Answer : DefinitionVein stripping is surgery to remove varicose veins in the legs.Alternative NamesVein stripping with ligation, avulsion, or ablation; Saphenous vein ligationDescriptionVaricose veins are swollen, ... either:General anesthesia and will be unconscious and unable to feel pain.Spinal anesthes

How do I keep my cordless screwdriver from stripping screw heads?

Description : How do I keep my cordless screwdriver from stripping screw heads?

Last Answer : The best thing to do is to not drill the screw heads to far down, since it will have a tendency to strip the screw heads, you should also consider making sure you item is prefectly mounted due to the problems of the screw.

What are the best and where do I find more info on weather stripping?

Description : What are the best and where do I find more info on weather stripping?

Last Answer : A garage door is important for so many reasons. First of all, it protects your garage, and anything in it, from the elements. This allows you to park your valuable vehicles in your garage without having to worry that they will be affected by the weather.

In a 4 S diesel engine, the term ‘squish’ refers to the (a) Injection of fuel in the precombustion chamber (b) Discharge of gases from the precombustion chamber (c) Entry of air into the combustion chamber (d) Stripping of fuel from the core

Description : In a 4 S diesel engine, the term ‘squish’ refers to the (a) Injection of fuel in the precombustion chamber (b) Discharge of gases from the precombustion chamber (c) Entry of air into the combustion chamber (d) Stripping of fuel from the core

Last Answer : Ans :c

Natural gasoline is produced (A) From oil wells (B) In oil refineries (C) By natural gas stripping (D) None of these

Description : Natural gasoline is produced (A) From oil wells (B) In oil refineries (C) By natural gas stripping (D) None of these

Last Answer : (C) By natural gas stripping

As the reflux ratio in a distillation column is increased from the minimum, the (A) Slope of the operating line in stripping section decreases (B) Number of plates decreases very slowly first and then more and more rapidly (C) Total cost first decreases and then increases (D) Liquid flow increases while the vapor flow decreases for a system

Description : As the reflux ratio in a distillation column is increased from the minimum, the (A) Slope of the operating line in stripping section decreases (B) Number of plates decreases very slowly first ... decreases and then increases (D) Liquid flow increases while the vapor flow decreases for a system

Last Answer : (C) Total cost first decreases and then increases

The reciprocal of stripping factor is termed as (A) Selectivity index (B) Relative volatility (C) Absorption factor (D) Murphree efficiency

Description : The reciprocal of stripping factor is termed as (A) Selectivity index (B) Relative volatility (C) Absorption factor (D) Murphree efficiency

Last Answer : (C) Absorption factor

In stripping section of continuous distillation column, the (A) Liquid is stripped of high boiler (B) Liquid is enriched with high boiler (C) Vapour is stripped of low boiler (D) None of these

Description : In stripping section of continuous distillation column, the (A) Liquid is stripped of high boiler (B) Liquid is enriched with high boiler (C) Vapour is stripped of low boiler (D) None of these

Last Answer : (B) Liquid is enriched with high boiler

In case of absorption & stripping, the interface of the liquid & gas phases are present in equilibrium, when the diffusional resistance of __________ is zero. (A) Interface (B) Gas phase (C) Liquid phase (D) All 'a', 'b' & 'c'

Description : In case of absorption & stripping, the interface of the liquid & gas phases are present in equilibrium, when the diffusional resistance of __________ is zero. (A) Interface (B) Gas phase (C) Liquid phase (D) All 'a', 'b' & 'c'

Last Answer : (A) Interface

Pick out the wrong statement (A) Co-current absorbers are usually used, when the gas to be dissolved in the liquid is a pure substance (B) In case of gas absorption, HETP is equal to HTU, when both the operating line & the equilibrium lines are parallel (C) Hatta number is important in case of gas absorption with chemical reaction (D) In actual practice, absorption is an endothermic process, while stripping is an exothermic process

Description : Pick out the wrong statement (A) Co-current absorbers are usually used, when the gas to be dissolved in the liquid is a pure substance (B) In case of gas absorption, HETP is ... reaction (D) In actual practice, absorption is an endothermic process, while stripping is an exothermic process

Last Answer : (D) In actual practice, absorption is an endothermic process, while stripping is an exothermic process

In gas-liquid contact operation, the number of ideal stages, N = (xa - xb )/(xb - x *b ). This is true when the stripping factor 'S' is (A) S > 1 (B) S < 1 (C) S = 1 (D) S = ∞

Description : In gas-liquid contact operation, the number of ideal stages, N = (xa - xb )/(xb - x *b ). This is true when the stripping factor 'S' is (A) S > 1 (B) S < 1 (C) S = 1 (D) S = ∞

Last Answer : (A) S > 1

For stripping of a gas in a counter current stripper, the operating line (A) Lies above the equilibrium curve (B) Lies below the equilibrium curve (C) Can lie above or below the equilibrium curve (D) Is always parallel to the equilibrium curve

Description : For stripping of a gas in a counter current stripper, the operating line (A) Lies above the equilibrium curve (B) Lies below the equilibrium curve (C) Can lie above or below the equilibrium curve (D) Is always parallel to the equilibrium curve

Last Answer : (C) Can lie above or below the equilibrium curve

In distillation where q is defined as the moles of liquid flow in the stripping section per mole of feed introduced, for saturated liquid feed (A) q > 1 (B) q < 1 (C) q = 1 (D) q = 0

Description : In distillation where q is defined as the moles of liquid flow in the stripping section per mole of feed introduced, for saturated liquid feed (A) q > 1 (B) q < 1 (C) q = 1 (D) q = 0

Last Answer : (C) q = 1

Stripping a thin layer of bark completely around a tree trunk will kill the tree, but a deep gouge along one side will not. Why?

Description : Stripping a thin layer of bark completely around a tree trunk will kill the tree, but a deep gouge along one side will not. Why? 

Last Answer : It must be remembered that the bark contains the phloem in its innermost region. The circumcision of even a thin layer of bark completely disrupts the movement of organic nutrients from the leaves and ... their strength, it does not reduce their ability to transport nutrients, and so they survive. 

The phenomenon occuring during pumping of a liquid solution containing dissolved gases, which may come out of the solution giving rise to gas pockets, is termed as (A) Evaporation (B) Cavitation (C) Sublimation (D) Stripping

Description : The phenomenon occuring during pumping of a liquid solution containing dissolved gases, which may come out of the solution giving rise to gas pockets, is termed as (A) Evaporation (B) Cavitation (C) Sublimation (D) Stripping

Last Answer : (B) Cavitation

Stripping of sugarcane leaves minimizes the attack of — a. Pyrillia b. Early shoot borer c. Top shoot borer d. Mealy bug

Description : Stripping of sugarcane leaves minimizes the attack of — a. Pyrillia b. Early shoot borer c. Top shoot borer d. Mealy bug

Last Answer : d. Mealy bug

Stripping of sugarcane leaves minimizes the attack of — a. Pyrillia b. Early shoot borer c. Top shoot borer d. Mealy bug

Description : Stripping of sugarcane leaves minimizes the attack of — a. Pyrillia b. Early shoot borer c. Top shoot borer d. Mealy bug

Last Answer : d. Mealy bug

State the requirement of good form work and state the stripping time of form work as per IS 456-2000. i) Slab ii) Beam iii) Column with labelling on sketch.

Description : State the requirement of good form work and state the stripping time of form work as per IS 456-2000. i) Slab ii) Beam iii) Column with labelling on sketch.

Last Answer : Requirement of good form work: 1. It should be strong enough to resist the weight of concrete, workers and machinery. 2. It should be economical compared to total cost of construction. 3. It should be possible ... arch of span more than 6m - 21 days iii) Column: Vertical formwork - 16 to 24 hours

What is an advantage of using a resistance soldering iron when soldering wire to a connector?

Description : What is an advantage of using a resistance soldering iron when soldering wire to a connector?

Last Answer : The soldering tips are hot only during the brief period of soldering the connection, thus minimizing the chance of burning the wire insulation or connector inserts.

What is used to tie wire bundles in high-temperature areas?

Description : What is used to tie wire bundles in high-temperature areas?

Last Answer : High-temperature, pressure-sensitive tape.

What size wire bundles require double lace?

Description : What size wire bundles require double lace?

Last Answer : Bundles that are 1 inch or larger in diameter

Why should wire be stripped 1/32 inch longer than the depth of the solder barrel?

Description : Why should wire be stripped 1/32 inch longer than the depth of the solder barrel?

Last Answer : To prevent burning the insulation during the soldering process and to allow the wire to flex easier at a stress point.

Should aluminum wire be cleaned prior to installing an aluminum terminal lug or splice?

Description : Should aluminum wire be cleaned prior to installing an aluminum terminal lug or splice?

Last Answer : No, it is done automatically by the petroleum abrasive compound that comes in the terminal or splices.

Why are the ends of the wire clamped down after a Western Union splice is made?

Description : Why are the ends of the wire clamped down after a Western Union splice is made?

Last Answer : To prevent damage to the tape insulation.

What tool should be used to strip aluminum wire?

Description : What tool should be used to strip aluminum wire?

Last Answer : Knife.

The large surface area of a waveguide greatly reduces what type of loss that is common in two-wire and coaxial lines?

Description : The large surface area of a waveguide greatly reduces what type of loss that is common in two-wire and coaxial lines?

Last Answer : Copper loss.

. Why are coaxial lines more efficient at microwave frequencies than two-wire transmission lines?

Description : . Why are coaxial lines more efficient at microwave frequencies than two-wire transmission lines?

Last Answer : The electromagnetic fields are completely confined

What is the purpose of the spring or wire around the leads of a new MOSFET?

Description : What is the purpose of the spring or wire around the leads of a new MOSFET?

Last Answer : To prevent damage from static electricity.

Conduction in which type of semiconductor material is similar to conduction in a copper wire?

Description : Conduction in which type of semiconductor material is similar to conduction in a copper wire?

Last Answer : N-type material.