Specific yield of well is a) Discharge per unit time b) Yield of well per metre of drawdown* c) Velocity of water per unit time d)None of the above

Specific yield of well is  
a) Discharge per unit time  
b) Yield of well per metre of drawdown*
c) Velocity of water per unit time  
d)None of the above
by

1 Answer

Answer :

b) Yield of well per metre of drawdown*
by

Related questions

The difference between static water level and pumping water level is known as: a drawdown b well yield c specific capacity d all are correct

Description : The difference between static water level and pumping water level is known as: a drawdown b well yield c specific capacity d all are correct

Last Answer : a drawdown

The main drawback of centrifugal pump is a)necessity of priming b) discharge from pump varies with the load of water c) For high heads efficiency is low up to 50% d) the suction lift is limited to 6 metre e) all of the above*

Description : The main drawback of centrifugal pump is a)necessity of priming b) discharge from pump varies with the load of water c) For high heads efficiency is low up to 50% d) the suction lift is limited to 6 metre e) all of the above*

Last Answer : e) all of the above*

While taking sample of water from well, sample is collected a)About 2 metre above the bottom of wel b) About 1 metre above the bottom of well * c)About 1 metres below the bottom of well d) none of the above

Description : While taking sample of water from well, sample is collected a)About 2 metre above the bottom of wel b) About 1 metre above the bottom of well * c)About 1 metres below the bottom of well d) none of the above

Last Answer : b) About 1 metre above the bottom of well *

In new Rail as well as second hand rails how much end bends of the rails in lateral direction are permitted when checked with one metre straight edge before welding? (i) ± 0.2 mm in lateral direction (ii) ± 0.3 mm in lateral direction (iii) ± 0.5 mm in latera

Description : In new Rail as well as second hand rails how much end bends of the rails in lateral direction are permitted when checked with one metre straight edge before welding? (i) ± 0.2 mm in lateral direction (ii) ± 0.3 mm in lateral direction (iii) ± 0.5 mm in latera

Last Answer : (iii) ± 0.5 mm in latera

Requirement of water for apron washing a. 5 litre per square metre per day b. 10 litre per square metre per day * c. 15 litre per square metre per day d. 20 litre per square metre per day

Description : Requirement of water for apron washing a. 5 litre per square metre per day b. 10 litre per square metre per day * c. 15 litre per square metre per day d. 20 litre per square metre per day

Last Answer : b. 10 litre per square metre per day *

Requirement of water for platform washing is a)5 litre per square metre per day * b)10 litre per square meter per day c) 15 litre per square metre per day d)20 litre per square metre per day

Description : Requirement of water for platform washing is a)5 litre per square metre per day * b)10 litre per square meter per day c) 15 litre per square metre per day d)20 litre per square metre per day

Last Answer : a)5 litre per square metre per day *

Specific yield of a well is (A) Quantity of water than can be drawn from the well (B) Flow of water per unit time (C) Total quantity of water available in the well (D) Quantity of water per unit time per unit draw-down

Description : Specific yield of a well is (A) Quantity of water than can be drawn from the well (B) Flow of water per unit time (C) Total quantity of water available in the well (D) Quantity of water per unit time per unit draw-down

Last Answer : (C) Total quantity of water available in the well

Consider the following statements: Mitra’s hyperbolic transition design is based on the principle that : 1. Flow depth in the canal, as well as the discharge, is constant 2. width of the canal varies along with the discharge 3. Rate of change of velocity per unit length of transition is constant throughout the length of the transition. Which of these statements are correct ? a) 1, 2 and 3 b) 1 and 2 only c) 2 and 3 only d) 1 and 3 only

Description : Consider the following statements: Mitra's hyperbolic transition design is based on the principle that : 1. Flow depth in the canal, as well as the discharge, is constant 2. width of the canal varies along with the discharge 3. Rate ... a) 1, 2 and 3 b) 1 and 2 only c) 2 and 3 only d) 1 and 3 only

Last Answer : d) 1 and 3 only

While doing final location survey, the centre line is fully marked with pegs at --- metre distance (a) 10m (b) 20m* (c) 30m (d) 50m

Description : While doing final location survey, the centre line is fully marked with pegs at --- metre distance (a) 10m (b) 20m* (c) 30m (d) 50m

Last Answer : (b) 20m*

RBG loading caters for maaaaximum axle load of…….tones for locomotive with trailing loadof…… tonnes/metre of track with maximum axle load of…….tonnes for wagons a)22.9,7.67,25 b)22.5,7.67,22.9* c)25,7.67,22.9, d)None of above

Description : RBG loading caters for maaaaximum axle load of…….tones for locomotive with trailing loadof…… tonnes/metre of track with maximum axle load of…….tonnes for wagons a)22.9,7.67,25 b)22.5,7.67,22.9* c)25,7.67,22.9, d)None of above

Last Answer : b)22.5,7.67,22.9*

GML loading caters for maaaaximum axle load of…….tonnes for locomotive with trailing load of………tonnes/metre. a)22.9,7.67* b)22.5,7.67 c)25,7.67 d)None of above

Description : GML loading caters for maaaaximum axle load of…….tonnes for locomotive with trailing load of………tonnes/metre. a)22.9,7.67* b)22.5,7.67 c)25,7.67 d)None of above

Last Answer : a)22.9,7.67*

The spacing of tube wells should generally be more than ----------from the circle of influence a)10 metre b)50 metre c)100 metre* d) 500 metre

Description : The spacing of tube wells should generally be more than ----------from the circle of influence a)10 metre b)50 metre c)100 metre* d) 500 metre

Last Answer : c)100 metre*

If w is the weight of water per cubic metre, Q is the discharge in cubic metres per sec and H is the total head, the required water horse power of the pump, is (A) wQH/15 (B) wQH/360 (C) wQH/220 (D) wQH/550

Description : If w is the weight of water per cubic metre, Q is the discharge in cubic metres per sec and H is the total head, the required water horse power of the pump, is (A) wQH/15 (B) wQH/360 (C) wQH/220 (D) wQH/550

Last Answer : (A) wQH/15

For a homogeneous earth dam 50 m high having 2 m free broad, a flow net was constructed and the results were : Number of potential drops = 2.4 Number of flow channels = 0.4. If co-efficiency of permeability of the dam material is 3 × 10-3 cm3 /sec, the discharge per metre length of dam, is (A) 12 × 10-5 m3 /sec (B) 24 × 10-3 m3 /sec (C) 6 × 10-5 m3 /sec (D) 24 × 10-5 m3 /sec

Description : For a homogeneous earth dam 50 m high having 2 m free broad, a flow net was constructed and the results were : Number of potential drops = 2.4 Number of flow channels = 0.4. If co-efficiency of permeability of the dam material is ... 24 10-3 m3 /sec (C) 6 10-5 m3 /sec (D) 24 10-5 m3 /sec

Last Answer : (D) 24 × 10-5 m3 /sec

For design of sewers for sullage, minimum velocity of ---- metres per second is taken. (a) 1.0 m sec* (b) 1.5 m/sec (c) 2.0 m/sec (d) 2.5 m/sec

Description : eFor design of sewers for sullage, minimum velocity of ---- metres per second is taken. (a) 1.0 m sec* (b) 1.5 m/sec (c) 2.0 m/sec (d) 2.5 m/sec

Last Answer : (a) 1.0 m sec*

Maximum vertical clearance (VC) for a slab/ girder bridges with discharge above 3000 cumecs is a) 300 mm b) 1500 mm c) 1800 mm* d) 600 mm

Description : Maximum vertical clearance (VC) for a slab/ girder bridges with discharge above 3000 cumecs is a) 300 mm b) 1500 mm c) 1800 mm* d) 600 mm

Last Answer : c) 1800 mm*

Minimum vertical clearance (VC) for a slab/ girder bridges with discharge of 0-30 cumecs is a) 300 mm b) 1500 mm c) 1800 mm d) 600 mm*

Description : Minimum vertical clearance (VC) for a slab/ girder bridges with discharge of 0-30 cumecs is a) 300 mm b) 1500 mm c) 1800 mm d) 600 mm*

Last Answer : d) 600 mm*

Recuperation test is carried out to determine (A) Turbidity of water (B) pH value of water (C) Yield of well (D) Discharge from a well

Description : Recuperation test is carried out to determine  (A) Turbidity of water  (B) pH value of water  (C) Yield of well  (D) Discharge from a well 

Last Answer : (A) Turbidity of water 

The discharge per unit plan area of a sedimentation tank, is generally called A. Over flow rate B. Surface loading C. Over flow velocity D. All the above

Description : The discharge per unit plan area of a sedimentation tank, is generally called A. Over flow rate B. Surface loading C. Over flow velocity D. All the above

Last Answer : ANS: D

In open channels, the specific energy is the (A) Total energy per unit discharge (B) Total energy measured with respect to the datum passing through the bottom of the channel (C) Total energy measured above the horizontal datum (D) Kinetic energy plotted above the free surface of water

Description : In open channels, the specific energy is the (A) Total energy per unit discharge (B) Total energy measured with respect to the datum passing through the bottom of the channel (C) Total energy measured above the horizontal datum (D) Kinetic energy plotted above the free surface of water

Last Answer : Answer: Option B

The dry density of soil is a) Always greater than the saturated density b) Weight of soil solids per unit of total volume prior to drying* c) Total weight of soil solids per unit of its total volume d) Total weight of soil mass per unit of its total volume

Description : The dry density of soil is a) Always greater than the saturated density b) Weight of soil solids per unit of total volume prior to drying* c) Total weight of soil solids per unit of its total volume d) Total weight of soil mass per unit of its total volume

Last Answer : b) Weight of soil solids per unit of total volume prior to drying*

For painting, the unit of rate is per a) Sqm b) cum c) 10sqm * d) 10cum

Description : For painting, the unit of rate is per a) Sqm b) cum c) 10sqm * d) 10cum

Last Answer : c) 10sqm *

Question No. 216 If the specific capacity of a well is 0.3183 × 10-3 per sec, the discharge from a well of 4 m diameter under a depression head of 4 m, is (A) 8 litres/sec (B) 10 litres/sec (C) 12 litres/sec (D) 16 litres/sec

Description : Question No. 216 If the specific capacity of a well is 0.3183 × 10-3 per sec, the discharge from a well of 4 m diameter under a depression head of 4 m, is (A) 8 litres/sec (B) 10 litres/sec (C) 12 litres/sec (D) 16 litres/sec

Last Answer : (D) 16 litres/sec

For the upstream face of an earthen dam, the most adverse condition for stability of slope is (A) Sudden drawdown (B) Steady seepage (C) During construction (D) Sloughing of slope

Description : For the upstream face of an earthen dam, the most adverse condition for stability of slope is (A) Sudden drawdown (B) Steady seepage (C) During construction (D) Sloughing of slope

Last Answer : Answer: Option A

Amount of water vapour in a unit volume (Cubic metre) of air is called: (1) Mixed ratio (2) relative humidity (3) absolute humidity (4) specific humidity

Description : Amount of water vapour in a unit volume (Cubic metre) of air is called: (1) Mixed ratio (2) relative humidity (3) absolute humidity (4) specific humidity

Last Answer : (3) absolute humidity Explanation: Absolute humidity is the measure of water vapor (moisture) in the air, regardless of temperature. It is expressed as grams of moisture per cubic meter of air (g/m3).

The water pressure per metre length on a vertical masonry wall of dam is (where w = Specific weight of the liquid, and H = Height of the liquid) (A) wH/2(B) wH (C) wH2 /2 (D) wH2 /4

Description : The water pressure per metre length on a vertical masonry wall of dam is (where w = Specific weight of the liquid, and H = Height of the liquid) (A) wH/2 (B) wH (C) wH2 /2 (D) wH2 /4

Last Answer : Answer: Option C

Velocity of water can be measured by a) Anemo meter b) Elco meter c) Current meter* d) Thermo meter

Description : Velocity of water can be measured by a) Anemo meter b) Elco meter c) Current meter* d) Thermo meter

Last Answer : c) Current meter*

Indicate which of the statement is incorrect (a) The detritus tank is type of a grit chamber (b) In detritus tank, velocity of flow is further reduced (c) Grit chambers are provided in the sewage treatment process to remove the heavier inorganic matter as grit, sand etc. from the sewage (d) None of them*

Description : Indicate which of the statement is incorrect (a) The detritus tank is type of a grit chamber (b) In detritus tank, velocity of flow is further reduced (c) Grit chambers are provided in the sewage ... to remove the heavier inorganic matter as grit, sand etc. from the sewage (d) None of them*

Last Answer : (d) None of them*

For achieving self-cleaning velocity, a minimum velocity of ---- mps. Is desirable for design peak flow (a) 0.6 mps (b) 0.8 mps* (c) 1.0 mps (d) 2.0 mps

Description : For achieving self-cleaning velocity, a minimum velocity of ---- mps. Is desirable for design peak flow (a) 0.6 mps (b) 0.8 mps* (c) 1.0 mps (d) 2.0 mps

Last Answer : b) 0.8 mps*

Self cleaning velocity of a sewer line depends upon (a) Diameter of sewer (b) Gradient of ewer line (c) Type of sewerage (d) All of them*

Description : Self cleaning velocity of a sewer line depends upon (a) Diameter of sewer (b) Gradient of ewer line (c) Type of sewerage (d) All of them*

Last Answer : d) All of them*

The wind velocity is measured using___

Description : The wind velocity is measured using___

Last Answer : Anemometer

Ultrasonic Pulse Velocity test is meant for a) Identifying the integrity of concrete* b) Finding the strength of concrete c) To know the crack in steel structure d) To know the flaw in rail

Description : Ultrasonic Pulse Velocity test is meant for a) Identifying the integrity of concrete* b) Finding the strength of concrete c) To know the crack in steel structure d) To know the flaw in rail

Last Answer : a) Identifying the integrity of concrete*

Permitted wind velocity for running of trains on the bridge a) 72 km/h* b) 58 km/h c) 64 km/h d) No limits

Description : Permitted wind velocity for running of trains on the bridge a) 72 km/h* b) 58 km/h c) 64 km/h d) No limits

Last Answer : a) 72 km/h*

For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Description : For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Last Answer : Answer: Option D

Tesla metre per ampere (T. m/A) is the unit for the measurement of (A) Magnetic susceptibility (B) Magnetic moment (C) Permeability of free space (D) Flux density

Description : Tesla metre per ampere (T. m/A) is the unit for the measurement of (A) Magnetic susceptibility (B) Magnetic moment (C) Permeability of free space (D) Flux density

Last Answer : Option C

The unit of viscosity is (A) Metres² per sec (B) kg-sec/metre (C) Newton-sec per metre² (D) Newton-sec per meter

Description : The unit of viscosity is (A) Metres² per sec (B) kg-sec/metre (C) Newton-sec per metre² (D) Newton-sec per meter

Last Answer : Answer: Option B

While determining the yield of open wells by the pumping test (A) Velocity of recharging water, increases with depression head (B) Depression head resulting at critical velocity, is called critical depression head (C) Working head is generally limited to (D) Maximum safe yield of an open well, is expected at critical depression head

Description : While determining the yield of open wells by the pumping test  (A) Velocity of recharging water, increases with depression head  (B) Depression head resulting at critical velocity, is called critical ... (D) Maximum safe yield of an open well, is expected at critical depression head 

Last Answer : (D) Maximum safe yield of an open well, is expected at critical depression head 

What is the life of portion? (i) 2 years (ii) No specific life.* (ii) 6 months (iv) 1 year

Description : What is the life of portion? (i) 2 years (ii) No specific life.* (ii) 6 months (iv) 1 year

Last Answer : (ii) No specific life.*

Piping in a soil mass is a) Erosion of subsoil by the high velocities of flow of water through it when such velocities exceed a certain limit* b) Caused due to very low exit gradient c) Due to continuous passage of water through a series of well connected pores d) Due to loss of the strength of cohesion less soil because of upward flow of of water

Description : Piping in a soil mass is a) Erosion of subsoil by the high velocities of flow of water through it when such velocities exceed a certain limit* b) Caused due to very low exit gradient c) ... connected pores d) Due to loss of the strength of cohesion less soil because of upward flow of of water

Last Answer : a) Erosion of subsoil by the high velocities of flow of water through it when such velocities exceed a certain limit*

hat action to be taken if slag is not separated within 20 ± 3 seconds? (i) Tap inside. (ii) Tap outside * (iii) Good reaction (iv) Tap well in time

Description : hat action to be taken if slag is not separated within 20 ± 3 seconds? (i) Tap inside. (ii) Tap outside * (iii) Good reaction (iv) Tap well in time

Last Answer : ii) Tap outside *

Both noting and protest are compulsory in case of A. Foreign Bills B. Inland Bills C. Foreign as well as Inland Bills D. None of them

Description : Both noting and protest are compulsory in case of A. Foreign Bills B. Inland Bills C. Foreign as well as Inland Bills D. None of them

Last Answer : C. Foreign as well as Inland Bills

“B” class station is provided only on (a) Single lines (b) Double line (c) On both single as well as double line* (d) None of them

Description : “B” class station is provided only on (a) Single lines (b) Double line (c) On both single as well as double line* (d) None of them

Last Answer : c) On both single as well as double line*

In new Rail as well as second hand rails how much end bends of the rails in vertical are permitted when checked with one meter straight edge before welding? (i) +0.5mm, -0 mm in vertical * (ii) +0.2mm, -.3 mm in vertical (iii) +0.3mm, -2 mm in vertical (iv) 0 mm, +.5 mm in vertical

Description : In new Rail as well as second hand rails how much end bends of the rails in vertical are permitted when checked with one meter straight edge before welding? (i) +0.5mm, -0 mm in vertical * (ii) +0.2mm, -.3 mm in vertical (iii) +0.3mm, -2 mm in vertical (iv) 0 mm, +.5 mm in vertical

Last Answer : (i) +0.5mm, -0 mm in vertical *

Maximum tilt specified during sinking of well foundation is a) 1 in 10 b) 1 in 50 c) 1 in 100* d) 1 in 150

Description : Maximum tilt specified during sinking of well foundation is a) 1 in 10 b) 1 in 50 c) 1 in 100* d) 1 in 150

Last Answer : c) 1 in 100*

Well foundation may be of the following type a) circular b) D type c) Double D type d) Any of the above*

Description : Well foundation may be of the following type a) circular b) D type c) Double D type d) Any of the above*

Last Answer : d) Any of the above*

One of the following is a shallow foundation a) Pile foundation b) Raft foundation* c) Under reamed pile foundation d) Well foundation

Description : One of the following is a shallow foundation a) Pile foundation b) Raft foundation* c) Under reamed pile foundation d) Well foundation

Last Answer : b) Raft foundation*

he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe at the same flow rate/average velocity, then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Description : he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe ... then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Last Answer : (B) 2Δp

A level crossing qualifies for construction of Road Over Bridge/ Under Bridge on Cost sharing basis with State Government when the Train Vehicle Unit is more than a) 50,000 b) 1, 00,000* c) 3, 00,000 d) 5, 00,000

Description : A level crossing qualifies for construction of Road Over Bridge/ Under Bridge on Cost sharing basis with State Government when the Train Vehicle Unit is more than a) 50,000 b) 1, 00,000* c) 3, 00,000 d) 5, 00,000

Last Answer : b) 1, 00,000*

TVU is abbreviated for a) Track vulnerable unit b) Train vehicle unit * c) Total vehicle unit d) Traffic variation unit

Description : TVU is abbreviated for a) Track vulnerable unit b) Train vehicle unit * c) Total vehicle unit d) Traffic variation unit

Last Answer : b) Train vehicle unit *

As per norms for desirable amenity as given to model station, the water coolers should be provided on stations classified as --- (a) A & B (b) A,B & C (c) A,B,C & D* (d) A, B,C, D & E (e) A

Description : As per norms for desirable amenity as given to model station, the water coolers should be provided on stations classified as --- (a) A & B (b) A,B & C (c) A,B,C & D* (d) A, B,C, D & E (e) A

Last Answer : (c) A,B,C & D*