Traditionally, waste heat of low temperature range ________ has not been used for electricitygeneration despite efforts by ORC companies, mainly because the Carnot efficiency is rather low. a) 0-250 °C b) 0-150 °C c) 0-200 °C d) 0-120 °C

Traditionally, waste heat of low temperature range ________ has not been used for electricitygeneration
despite efforts by ORC companies, mainly because the Carnot efficiency is rather low.
a) 0-250 °C
b) 0-150 °C
c) 0-200 °C
d) 0-120 °C
by

1 Answer

Answer :

0-120 °C
by

Related questions

A high temperature waste heat recovery unit consists of recovering waste heat at temperaturesgreater than _______. a) 200 °C b) 500 °C c) 300 °C d) 400 °C

Description : A high temperature waste heat recovery unit consists of recovering waste heat at temperaturesgreater than _______. a) 200 °C b) 500 °C c) 300 °C d) 400 °C

Last Answer : 400 °C

Mercury electrolytic cell produces 50-70% NaOH solution. Its operating temperature is __________ °C. (A) 25 (B) 60-70 (C) 150-200 (D) 250-300

Description : Mercury electrolytic cell produces 50-70% NaOH solution. Its operating temperature is __________ °C. (A) 25 (B) 60-70 (C) 150-200 (D) 250-300

Last Answer : (B) 60-70

The pressure (kg/cm2 ) and temperature (°C) maintained in electrical desalters for crude oil are respectively (A) 10 and 120 (B) 1 and 200 (C) 50 and 250 (D) 10 and 300

Description : The pressure (kg/cm2 ) and temperature (°C) maintained in electrical desalters for crude oil are respectively (A) 10 and 120 (B) 1 and 200 (C) 50 and 250 (D) 10 and 300

Last Answer : (B) 1 and 200

Light oil whose major component is Benzol, is obtained by the distillation of crude tar in the temperature range of __________ °C. (A) 80-170 (B) 200-300 (C) 250-270

Description : Light oil whose major component is Benzol, is obtained by the distillation of crude tar in the temperature range of __________ °C. (A) 80-170 (B) 200-300 (C) 250-270

Last Answer : (A) 80-170

Carnot cycle efficiency depends upon  (a) properties of the medium/substance used  (b) condition of engine  (c) working condition  (d) temperature range of operation  (e) effectiveness of insulating material around the engine.

Description : Carnot cycle efficiency depends upon  (a) properties of the medium/substance used  (b) condition of engine  (c) working condition  (d) temperature range of operation  (e) effectiveness of insulating material around the engine.

Last Answer : Answer : d

A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Last Answer : (B) 100

The following heat engine produces power of 100,000 kW. The heat engine operates between 800 K and 300 K. It has a thermal efficiency equal to 50% of that of the Carnot engine for the same temperature. The rate at which heat is absorbed from the hot reservoir is (A) 100,000 kW (B) 160,000 kW (C) 200,000 kW (D) 320,000 kW

Description : The following heat engine produces power of 100,000 kW. The heat engine operates between 800 K and 300 K. It has a thermal efficiency equal to 50% of that of the Carnot engine for the same temperature. The rate at which heat is ... is (A) 100,000 kW (B) 160,000 kW (C) 200,000 kW (D) 320,000 kW

Last Answer : (D) 320,000 kW

What is the highest efficiency of heat engine operating between the two thermal energy reservoirs at temperature limits?  A. Ericson efficiency  B. Otto efficiency  C. Carnot efficiency  D. Stirling efficiency

Description : What is the highest efficiency of heat engine operating between the two thermal energy reservoirs at temperature limits?  A. Ericson efficiency  B. Otto efficiency  C. Carnot efficiency  D. Stirling efficiency

Last Answer : Carnot efficiency

212 °F = _____ °C  a. 200  b. 150  c. 100  d. None of the above

Description : 212 °F = _____ °C  a. 200  b. 150  c. 100  d. None of the above

Last Answer : 100

Condensation polymerisation of caprolactam is carried out in the reactor maintained at a temperature of __________ °C for producing nylon- 6. (A) -20 to 25 (B) 50 to 75 (C) 100 to 150 (D) 250-280

Description : Condensation polymerisation of caprolactam is carried out in the reactor maintained at a temperature of __________ °C for producing nylon- 6. (A) -20 to 25 (B) 50 to 75 (C) 100 to 150 (D) 250-280

Last Answer : (D) 250-280

Using an organic fluid that boils at a low temperature means that energy could be regeneratedfrom waste fluids is known as ________. a) Heat exchanger b) Heat remover c) Heat pumps d) Heat absorber`

Description : Using an organic fluid that boils at a low temperature means that energy could be regeneratedfrom waste fluids is known as ________. a) Heat exchanger b) Heat remover c) Heat pumps d) Heat absorber

Last Answer : Heat pumps

Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat of the substance): 0.20 kCal/kg oC DT (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Description : Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat ... (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Last Answer : 21600

A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2 MN/mm2 , the tensile force developed at a temperature of 50°C, is (A) 80 N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option

Description : A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the  ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2  MN/mm2 , the ... N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option 

Last Answer : (C) 120 N/mm

The weight of the puddler is —— A. 150-200 kg. C. 100-150 kg B. 30-40 kg D. 200-250 kg

Description : The weight of the puddler is —— A. 150-200 kg. C. 100-150 kg B. 30-40 kg D. 200-250 kg

Last Answer : 30-40 kg

Metallic recuperators are not used for waste heat recovery, if the hot flue gas temperature is above __________ °C, because corrosion prevails at higher temperatures. (A) 350 (B) 750 (C) 1050 (D) 1250

Description : Metallic recuperators are not used for waste heat recovery, if the hot flue gas temperature is above __________ °C, because corrosion prevails at higher temperatures. (A) 350 (B) 750 (C) 1050 (D) 1250

Last Answer : (B) 750

Hot extrusion of aluminium is done in the temperature range of __________ °C. (A) 550-600 (B) 450-500 (C) 350-400 (D) 250-300

Description : Hot extrusion of aluminium is done in the temperature range of __________ °C. (A) 550-600 (B) 450-500 (C) 350-400 (D) 250-300

Last Answer : (C) 350-400

Brinell Hardness Number (BHN) for talc is approximately in the range of (A) 1-5 (B) 20-30 (C) 100 -150 (D) 200 - 250

Description : Brinell Hardness Number (BHN) for talc is approximately in the range of (A) 1-5 (B) 20-30 (C) 100 -150 (D) 200 - 250

Last Answer : (B) 20-30

Regeneration of molecular sieve requires it to be heated to a temperature of about __________ °C. (A) 80-120 (B) 200-300 (C) 600-800 (D) 1000-1100

Description : Regeneration of molecular sieve requires it to be heated to a temperature of about __________ °C. (A) 80-120 (B) 200-300 (C) 600-800 (D) 1000-1100

Last Answer : (D) 1000-1100

Fermentation of molasses to produce ethyl alcohol is done at __________ °C. (A) 20 - 30 (B) < - 5 (C) 100 - 150 (D) 250 - 300

Description : Fermentation of molasses to produce ethyl alcohol is done at __________ °C. (A) 20 - 30 (B) < - 5 (C) 100 - 150 (D) 250 - 300

Last Answer : (A) 20 - 30

If both Stirling and Carnot cycles operate within the same temperature limits, then efficiency of Stirling cycle as compared to Carnot cycle  (a) more  (b) less  (c) equal  (d) depends on other factors  (e) none of the above.

Description : If both Stirling and Carnot cycles operate within the same temperature limits, then efficiency of Stirling cycle as compared to Carnot cycle  (a) more  (b) less  (c) equal  (d) depends on other factors  (e) none of the above.

Last Answer : Answer : c

Carnot cycle efficiency is maximum when  (a) initial temperature is 0°K  (b) final temperature is 0°K  (c) difference between initial and final temperature is 0°K  (d) final temperature is 0°C  (e) initial temperature is minimum possible.

Description : Carnot cycle efficiency is maximum when  (a) initial temperature is 0°K  (b) final temperature is 0°K  (c) difference between initial and final temperature is 0°K  (d) final temperature is 0°C  (e) initial temperature is minimum possible.

Last Answer : Answer : b

The more effective way of increasing efficiency of Carnot engine is to  (a) increase higher temperature  (b) decrease higher temperature  (c) increase lower temperature  (d) decrease lower temperature  (e) keep lower temperature constant.

Description : The more effective way of increasing efficiency of Carnot engine is to  (a) increase higher temperature  (b) decrease higher temperature  (c) increase lower temperature  (d) decrease lower temperature  (e) keep lower temperature constant.

Last Answer : Answer : d

Motorized knapsack sprayer blade rotation at about ……. To rev/min. a. 200 to 300. c. 100 to 120 b. 120 to 400. d. 150 to 300

Description : Motorized knapsack sprayer blade rotation at about ……. To rev/min. a. 200 to 300. c. 100 to 120 b. 120 to 400. d. 150 to 300

Last Answer : 100 to 120

The injection pressure of ic engine used on tractors is in range of kg/cm2 1. 0-6 2. 60-120 3. 120-200 4. 200-300

Description : The injection pressure of ic engine used on tractors is in range of kg/cm2 1. 0-6 2. 60-120 3. 120-200 4. 200-300

Last Answer : ans 3

A waste heat recovery unit (WHRU) is an_________ that transfers heat from process outputs at high temperature to another part of the process for some purpose, usually increased efficiency. a) Energy recovery heat exchanger b) Energy recovery heat diffuser c) Both ‘a’ and ‘b’ d) None of the above

Description : A waste heat recovery unit (WHRU) is an_________ that transfers heat from process outputs at high temperature to another part of the process for some purpose, usually increased efficiency. a) Energy recovery heat exchanger b) Energy recovery heat diffuser c) Both ‘a’ and ‘b’ d) None of the above

Last Answer : Energy recovery heat exchanger

What is the range of tempering temperature (°C) for most of the materials? (A) 75-100 (B) 200-300 (C) 350-450 (D) 500-600

Description : What is the range of tempering temperature (°C) for most of the materials? (A) 75-100 (B) 200-300 (C) 350-450 (D) 500-600

Last Answer : (B) 200-300

Efficiency of a heat engine working on Carnot cycle between two temperature levels depends upon the (A) Two temperatures only (B) Pressure of working fluid (C) Mass of the working fluid (D) Mass and pressure both of the working fluid

Description : Efficiency of a heat engine working on Carnot cycle between two temperature levels depends upon the (A) Two temperatures only (B) Pressure of working fluid (C) Mass of the working fluid (D) Mass and pressure both of the working fluid

Last Answer : (A) Two temperatures only

In a counter flow heat exchanger, hot fluid enters at 170°C & leaves at 150°C, while the cold fluid enters at 50°C & leaves at 70°C. The arithmetic mean temperature difference in this case is __________ °C. (A) 20 (B) 60 (C) 120 (D) ∞

Description : In a counter flow heat exchanger, hot fluid enters at 170°C & leaves at 150°C, while the cold fluid enters at 50°C & leaves at 70°C. The arithmetic mean temperature difference in this case is __________ °C. (A) 20 (B) 60 (C) 120 (D) ∞

Last Answer : (D) ∞

Molecular sieves are regenerated by heating to __________ °C. (A) < 150 (B) 200-330 (C) > 500 (D) > 1000

Description : Molecular sieves are regenerated by heating to __________ °C. (A) < 150 (B) 200-330 (C) > 500 (D) > 1000

Last Answer : (B) 200-330

The efficiency of Joule cycle is  A. greater than Carnot cycle  B. less than Carnot cycle  C. equal to Carnot cycle  D. none of these

Description : The efficiency of Joule cycle is  A. greater than Carnot cycle  B. less than Carnot cycle  C. equal to Carnot cycle  D. none of these

Last Answer : Answer: B

The efficiency of Stirling cycle is __________ Carnot cycle.  A. greater than  B. less than  C. equal to

Description : The efficiency of Stirling cycle is __________ Carnot cycle.  A. greater than  B. less than  C. equal to

Last Answer : Answer: C

Which of the following cycles has maximum efficiency  (a) Rankine  (b) Stirling  (c) Carnot  (d) Brayton  (e) Joule.

Description : Which of the following cycles has maximum efficiency  (a) Rankine  (b) Stirling  (c) Carnot  (d) Brayton  (e) Joule.

Last Answer : Answer : c

The efficiency of Carnot cycle is maximum for  (a) gas engine  (b) well lubricated engine  (c) petrol engine  (d) steam engine  (e) reversible engine.

Description : The efficiency of Carnot cycle is maximum for  (a) gas engine  (b) well lubricated engine  (c) petrol engine  (d) steam engine  (e) reversible engine.

Last Answer : Answer : e

The efficiency of a Carnot engine depends on  (a) working substance  (b) design of engine  (c) size of engine  (d) type of fuel fired  (e) temperatures of source and sink.

Description : The efficiency of a Carnot engine depends on  (a) working substance  (b) design of engine  (c) size of engine  (d) type of fuel fired  (e) temperatures of source and sink.

Last Answer : Answer : e

An actual engine is to be designed having same efficiency as the Carnot cycle. Such a proposition is  (a) feasible  (b) impossible  (c) possible  (d) possible, but with lot of sophistications  (e) desirable.

Description : An actual engine is to be designed having same efficiency as the Carnot cycle. Such a proposition is  (a) feasible  (b) impossible  (c) possible  (d) possible, but with lot of sophistications  (e) desirable.

Last Answer : Answer : d

Carnot cycle has maximum efficiency for  (a) reversible engine  (b) irreversible engine  (c) new engine  (d) petrol engine  (e) diesel engine.

Description : Carnot cycle has maximum efficiency for  (a) reversible engine  (b) irreversible engine  (c) new engine  (d) petrol engine  (e) diesel engine.

Last Answer : Answer : a

Which is the incorrect statement about Carnot cycle?  A. It is used as the alternate standard of comparison of all heat engines.  B. All the heat engines are based on Carnot cycle.  C. It provides concept of maximising work output between the two temperature limits.  D. all of the above

Description : Which is the incorrect statement about Carnot cycle?  A. It is used as the alternate standard of comparison of all heat engines.  B. All the heat engines are based on Carnot cycle.  C. It provides concept of maximising work output between the two temperature limits.  D. all of the above

Last Answer : Answer: B

The thermodynamic difference between a Rankine cycle working with saturated steam and the Carnot cycle is that  (a) carnot cycle can’t work with saturated steam  (b) heat is supplied to water at temperature below the maximum temperature of the cycle  (c) a rankine cycle receives heat at two places  (d) rankine cycle is hypothetical  (e) none of the above.

Description : The thermodynamic difference between a Rankine cycle working with saturated steam and the Carnot cycle is that  (a) carnot cycle can't work with saturated steam  (b) heat is supplied to water at temperature ... heat at two places  (d) rankine cycle is hypothetical  (e) none of the above.

Last Answer : Answer : b

In a Carnot cycle, heat is transferred at  (a) constant pressure  (b) constant volume  (c) constant temperature  (d) constant enthaply  (e) any one of the above.

Description : In a Carnot cycle, heat is transferred at  (a) constant pressure  (b) constant volume  (c) constant temperature  (d) constant enthaply  (e) any one of the above.

Last Answer : Answer : c

How many laboratories for Agri product testing have been recently set up by Agricultural and Processed Food Products Export Development Authority (APEDA)? a) 200 b) 250 c) 150 d) 186

Description : How many laboratories for Agri product testing have been recently set up by Agricultural and Processed Food Products Export Development Authority (APEDA)? a) 200 b) 250 c) 150 d) 186

Last Answer : d) 186

Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above

Description : Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above

Last Answer : Billet Reheating Furnace

Exothermic condensation reaction of monochlorobenzene with chloral in presence of 20% oleum as catalyst produces DDT. The reaction temperature is maintained at __________ °C. (A) 15-30 (B) 90-100 (C) 250-300 (D) < 0

Description : Exothermic condensation reaction of monochlorobenzene with chloral in presence of 20% oleum as catalyst produces DDT. The reaction temperature is maintained at __________ °C. (A) 15-30 (B) 90-100 (C) 250-300 (D) < 0

Last Answer : (A) 15-30

Weight per unit of drawbar power is generally ranges between a)50-120kg/kw b)120-150kg/kw c)150-250kg/kw d)250-300kg/kw

Description : Weight per unit of drawbar power is generally ranges between a)50-120kg/kw b)120-150kg/kw c)150-250kg/kw d)250-300kg/kw

Last Answer : a)50-120kg/kw

A major advantage of waste heat recovery in industry is a) Reduction in pollution c) Increase efficiency d) None of the above

Description : A major advantage of waste heat recovery in industry is a) Reduction in pollution c) Increase efficiency d) None of the above

Last Answer : Reduction in pollution

Major advantage of waste heat recovery in industry is: a) Reduction in pollution b) increase in efficiency c) Both a & b d) none of the above

Description : Major advantage of waste heat recovery in industry is: a) Reduction in pollution b) increase in efficiency c) Both a & b d) none of the above

Last Answer : Both a & b

Utilizing the answer to the previous problem, estimate the overall or average increase in temperature ( ΔT) of the concrete roof from the energy absorbed from the sun during a12hour day. Assume that all of the radiation absorbed goes into heating the roof. The specific heat of concrete is about 900 J/kg, and the density is about 2,300 kg/m3 .  a. 7.9 °C  b. 8.9°C  c. 9.9°C  d. 10.9°C formula: ΔQ = m c ΔT

Description : Utilizing the answer to the previous problem, estimate the overall or average increase in temperature ( ΔT) of the concrete roof from the energy absorbed from the sun during a12hour day. Assume that all of the radiation absorbed goes into ... °C  b. 8.9°C  c. 9.9°C  d. 10.9°C formula: ΔQ = m c ΔT

Last Answer : 7.9 °C

The amount of heat required to raise the temperature of 1kg of water through 1 °C is called ______.  A. Calorie  B. Joule  C. BTU  D. Kilocalorie

Description : The amount of heat required to raise the temperature of 1kg of water through 1 °C is called ______.  A. Calorie  B. Joule  C. BTU  D. Kilocalorie

Last Answer : Kilocalorie

A waste heat recovery unit is an energy recovery heat exchanger that transfers heat from process outputs at ........ a) High temperature b) Medium temperature c) Low temperature d) Both a & b

Description : A waste heat recovery unit is an energy recovery heat exchanger that transfers heat from process outputs at ........ a) High temperature b) Medium temperature c) Low temperature d) Both a & b

Last Answer : High temperature

In a low to medium temperature waste heat recovery system which of the device is most suitable a) Economiser b) Heat wheels c) air preheater d) Recuperator

Description : In a low to medium temperature waste heat recovery system which of the device is most suitable a) Economiser b) Heat wheels c) air preheater d) Recuperator

Last Answer : Heat wheels

The efficiency of a Carnot heat engine operating between absolute temperatures T1 and T2 (when, T1 > T2) is given by (T1- T2)/T1. The co efficient of performance (C.O.P.) of a Carnot heat pump operating between T1 and T2is given by (A) T1/(T1-T2) (B) T2/(T1-T2) (C) T1/T2 (D) T2/R1

Description : The efficiency of a Carnot heat engine operating between absolute temperatures T1 and T2 (when, T1 > T2) is given by (T1- T2)/T1. The co efficient of performance (C.O.P.) of a Carnot heat pump operating between T1 and T2is given by (A) T1/(T1-T2) (B) T2/(T1-T2) (C) T1/T2 (D) T2/R1

Last Answer : (A) T1/(T1-T2)