Description : Nellore to medium temperature waste heat recovery system the most suitable device is ------ a) Economizer b) Heat wheels c) Air preheater d) Recuperate d) Carbonate
Last Answer : Heat wheels
Description : Which of the following is not a continuous waste heat recovery equipment from the flue gases going out of furnace? (A) Economiser (B) Regenerator (C) Ceramic recuperator (D) Waste heat boiler
Last Answer : (B) Regenerator
Description : Waste heat from the outgoing flue gases in a thermal power plant is recovered by a/an (A) Economiser (B) Steam superheater (C) Air preheater (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Air preheater is not used as a waste heat recovery system in a____. a) Boiler b) billet Reheating Furnace c) Heat treatment furnace d) compressor
Last Answer : compressor
Description : Pick up the odd one out: b) Regenerator c) Recuperator d) Metallic recuperator e) Economiser
Last Answer : Economiser
Description : In which of the waste heat recovery equipment, the flow of flue gas and air is alternately reversed after a fixed interval of time? (A) Recuperator (B) Regenerator (C) Waste heat boiler (D) None of these
Description : Sensible heat of hot industrial flue gases cannot be recovered by a/an (A) Economiser (B) Regenerator (C) Ceramic recuperator (D) None of these
Last Answer : (D) None of these
Description : A waste heat recovery unit is an energy recovery heat exchanger that transfers heat from process outputs at ........ a) High temperature b) Medium temperature c) Low temperature d) Both a & b
Last Answer : High temperature
Description : The system is suitable to recover heat from ........ temperature exhaust gases . a) Medium-low b) Medium-high c) High-low d) High
Last Answer : Medium-high
Description : Recovery of heat from dryer exhaust air is a typical application of: a) Waste heat recovery boiler b) Heat pump c) Heat wheel d) Economizer
Last Answer : Heat wheel
Description : In industrial operations fluids with temperature less than __________ are set as the limit for waste heat recovery because of the risk of condensation of corrosive liquids a. 80C b. 100C c. 120C d. 200C
Last Answer : 100C
Description : Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat ... (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000
Last Answer : 21600
Description : A high temperature waste heat recovery unit consists of recovering waste heat at temperaturesgreater than _______. a) 200 °C b) 500 °C c) 300 °C d) 400 °C
Last Answer : 400 °C
Description : A waste heat recovery unit (WHRU) is an_________ that transfers heat from process outputs at high temperature to another part of the process for some purpose, usually increased efficiency. a) Energy recovery heat exchanger b) Energy recovery heat diffuser c) Both ‘a’ and ‘b’ d) None of the above
Last Answer : Energy recovery heat exchanger
Description : Which of the following is the most suitable for preheating combustion air above 650°C? (A) Regenerator (B) Metallic recuperator (C) Ceramic recuperator (D) None of these
Last Answer : (C) Ceramic recuperator
Description : A waste heat recovery system in industrial process has been key to reduce ....... Consumption. a) Coal b) Fuel c) Biogas d) Oil
Last Answer : Fuel
Description : Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above
Last Answer : Billet Reheating Furnace
Description : What are the benefits or the advantages of waste heat recovery units (WHRU)? a) Reduced Pollution b) Reduced equipment sizes c) Reduced auxiliary energy consumption. d) All of the above
Last Answer : All of the above
Description : The waste heat recovery unit (WHRU) is a tool involved in _______. a) Regeneration b) Cogeneration c) Both ‘a’ and ‘b’ d) None of the above
Last Answer : Cogeneration
Description : One of the key areas for ....... energy saving in existing systems is waste heat recovery. a) Potential b) Kinetic c) Thermal d) Electrical
Last Answer : Potential
Description : Techniques of waste heat recovery ....... a) Direct contact condensation b) Indirect contact condensation c) Transport membrane condensation d) All of the above
Description : A major advantage of waste heat recovery in industry is a) Reduction in pollution c) Increase efficiency d) None of the above
Last Answer : Reduction in pollution
Description : Recovery of waste heat from hot fluid to fluid is called: a) thermo compressor b) waste heat recovery boiler c) heat Pump d) economizer
Last Answer : heat Pump
Description : Major advantage of waste heat recovery in industry is: a) Reduction in pollution b) increase in efficiency c) Both a & b d) none of the above
Last Answer : Both a & b
Description : In regenerative air preheater (as practised in heating of coke ovens), the heat is transferred (A) Through a metallic wall (B) By direct contact of hot flue gas with air (C) By ... material (like chequor bricks) and then heating the air from this hot material (D) None of these
Last Answer : (C) By heating an intermediate material (like chequor bricks) and then heating the air from this hot material
Description : The economiser is used in boilers to........ A]Increase thermal efficiency of boiler B]Economise on fuel C]Extract heat from the exhaust the gases D]Increase flue gas temperature
Last Answer : A]Increase thermal efficiency of boiler
Description : Use of economiser in a boiler plant reduces the fuel consumption for steam generation by about __________ percent. (A) 1 (B) 10 (C) 30 (D) 50
Last Answer : (B) 10
Description : Traditionally, waste heat of low temperature range ________ has not been used for electricitygeneration despite efforts by ORC companies, mainly because the Carnot efficiency is rather low. a) 0-250 °C b) 0-150 °C c) 0-200 °C d) 0-120 °C
Last Answer : 0-120 °C
Description : Using an organic fluid that boils at a low temperature means that energy could be regeneratedfrom waste fluids is known as ________. a) Heat exchanger b) Heat remover c) Heat pumps d) Heat absorber
Last Answer : Heat pumps
Description : To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)
Description : Metallic recuperators are not used for waste heat recovery, if the hot flue gas temperature is above __________ °C, because corrosion prevails at higher temperatures. (A) 350 (B) 750 (C) 1050 (D) 1250
Last Answer : (B) 750
Description : Design of waste heat boiler for recovery of waste heat from furnace gases depends upon the (A) Quantity & temperature of waste gas (B) Dust concentration & nature of dust in waste gas (C) Corrosive nature of the waste gas (D) All (A), (B) and (C)
Last Answer : (B) Dust concentration & nature of dust in waste gas
Description : A seed drill with mechanical seed metering device mainly consists of: Frame, Seed box, Seed metering mechanism, drive transmission system, Furrow openers, Covering device, ……, hitch frame and Transport wheels. b. Differential c. U.V joints d. None of the above.
Last Answer : Ans - a. clutch
Description : Heat loss can be classified into ....... a) High temperature b) Low temperature c) Medium temperature d) All of the above
Description : An equipment which converts the latent or sensible heat of one fluid into the latent heat of vaporisation of another, is called a (A) Boiler (B) Heat exchanger (C) Recuperator (D) Regenerato
Last Answer : (B) Heat exchanger
Description : What is the function of Air preheater?
Last Answer : Air pre heater is used to transfer heat from the flue gases to the air before it passes into the furnace for combustion thereby increasing the thermal efficiency of the process.
Description : What Is The Use Of Air Preheater?
Last Answer : Air pre heater is used to transfer heat from the flue gases to the air before it passes into the furnace for combustion. It is placed between the economizer and chimney. The overall efficiency of the plant may be increased by 10 per cent by the use of air preheater.
Description : Waste heat Recovery system
Last Answer : Waste heat Recovery system Waste heat is energy that is rejected to the environment. It arises from equipment and operating inefficiencies, as well as from thermodynamic limitations on equipment and ... to minimize these costs, and to reduce environmental impact along with several other benefits.
Description : Heat recovery equipment will be most effective when the temperature of flue gas is: a) 250oC b) 200 oC c)400 oC d) 280 oC
Last Answer : 400 oC
Description : The function of an economiser in a boiler is to preheat the (A) Feedwater (B) Combustion air (C) Pulverised coal (D) Furnace oil
Last Answer : (A) Feedwater
Description : The thermal efficiency of an air/fuel gas preheating recuperator may be as high as __________ percent. (A) 50 (B) 65 (C) 85 (D) 99
Last Answer : (C) 85
Description : Thermal efficiency of furnaces can be improved by (A) Waste heat recovery from flue gas (B) Minimising heat losses from furnace walls (C) Maintaining proper draught (D) All (A), (B) and (C
Last Answer : (D) All (A), (B) and (C
Description : Regenerators are used for waste heat recovery in (A) By-product coke ovens (B) Beehive coke oven (C) Blast furnace stoves (D) Soaking pits
Last Answer : (A) By-product coke ovens
Description : Heat transfer rate to the stock/charge in the furnace does not depend upon the (A) Emissivity of the refractory walls (B) Size of the furnace (C) Use of waste heat recovery equipments (D) Thickness of the stock
Last Answer : (C) Use of waste heat recovery equipments
Description : Pitch creosote mixture (PCM) as compared to furnace oil is a better fuel, because its (A) Emissivity factor is higher (B) Sulphur content is lower (C) Flue gas has lower dew point thereby facilitating more waste heat recovery (D) All (A), (B) and (C)
Description : Define the term waste heat recovery?
Last Answer : Waste heat is the heat which is not at all used and exhausted out as a waste product. Waste heat is normally available from the industry in the form of process steam and water at high ... industries. This heat can be recovered for useful purpose. This process is known-as waste heat recovery.
Description : Define The Term Waste Heat Recovery?
Last Answer : Waste heat is the heat which is not at all used and exhausted out as a waste product. Waste heat is normally available from the industry in the form of process steam and water at high ... industries. This heat can be recovered for useful purpose. This process is known as waste heat recovery.
Description : Benefits of Waste Heat Recovery a. Reduction in pollution b. Reduction in equipment sizes c. Reduction in auxiliary energy consumption d. All of the above
Last Answer : Ans:- d. All of the above
Description : The waste heat energy could be used to produce ....... a) Cool air b) Hot air c) Exhaust gas d) All of the above
Last Answer : Cool air
Description : Which of the following waste types are not suitable for co-combustion in cement kilns? a) Chlorine b) Hydrogen c) Calcium d) Carbonate
Last Answer : Chlorine