Description : The coefficient of performance (COP) is the ratio between the: A. Power consumption in watts and heat absorbed per hour B. Heat absorbed per hour and the power consumption in watts C. Work required and the absorbed heat D. Absorbed heat and work required
Last Answer : Absorbed heat and work required
Description : Which one is the correct relation between energy efficiency ratio (EER) and coefficient of performance (COP)? A. EER = 2.34 COP B. EER = 3.24 COP C. EER = 3.42 COP D. EER = 4.23 COP
Last Answer : EER = 3.42 COP
Description : The relative coefficient of performance is (a) actual COP/theoretical COP (b) theoretical COP/actual COP (c) actual COP x theoretical COP (d) 1-actual COP x theoretical COP
Last Answer : Ans: a
Description : The thermal efficiency of a reversible heat engine operating between two given thermal reservoirs is 0.4. The device is used either as a refrigerator or as a heat pump between the same reservoirs. Then the coefficient of performance as a ... )R = 1.5; (COP)HP = 2.5 (D) (COP)R = (COP)HP = 2.5
Last Answer : (C) (COP)R = 1.5; (COP)HP = 2.5
Description : For obtaining high COP, the pressure range of compressor should be q. a) High. c) Optimum b) Low. d) Any value
Last Answer : LOW
Description : What refers to the amount of heat removed from the cooled space in BTS’s for 1 watt-hour of electricity consumed? A. Cost efficiency rating B. Energy efficiency rating C. Coefficient of performance D. Cost of performance
Last Answer : Energy efficiency rating
Description : Co-efficient of Performance (COP) of a refrigerator is the ratio of the (A) Work required to refrigeration obtained (B) Refrigeration obtained to the work required (C) Lower to higher temperature (D) Higher to lower temperature
Last Answer : (B) Refrigeration obtained to the work required
Description : Out of the following refrigeration cycles, which one has the minimum COP (Co-efficient of performance)? (A) Air cycle (B) Carnot cycle (C) Ordinary vapour compression cycle (D) Vapour compression with a reversible expansion engine
Last Answer : A) Air cycle
Description : The co-efficient of performance (COP) of a refrigerating system, which is its index of performance, is defined as the ratio of useful refrigeration to the net work. The units of __________ and COP are the same. (A) Kinematic viscosity (B) Work (C) Temperature (D) None of these
Last Answer : (D) None of these
Description : The Carnot co-efficient of performance (COP) of a domestic air conditioner compared to a household refrigerator is (A) Less (B) More (C) Same (D) Dependent on climatic conditions
Last Answer : (A) Less
Description : What is the use of flash chamber in a vapour compression refrigeration cycle to improve the COP of refrigeration cycle ?
Last Answer : When liquid refrigerant as obtained from condenser is throttled, there are some vapours. These vapours if carried through the evaporator will not contribute to refrigerating effect. Using a flash ... out in stages. Similarly compression process is also done in two separate compressor stages.
Description : What is the relationship between COP of heating and cooling ?
Last Answer : COP of heating is one(unity) more than COP of cooling.
Description : Wind load analysis can be performed following methods. a) experiments wind pressure coefficient b) shape factors c) wind-induced vibration coefficient d) all of above
Last Answer : all of above
Description : What is defined as the ratio of the change in temperature to the change in pressure when a real gas is throttled? A. Rankine coefficient B. Kelvin coefficient C. Maxwell-Boltzmann coefficient D. Joule-Thomson coefficient
Last Answer : Joule-Thomson coefficient
Description : For obtaining high COP, the pressure range of compressor should be (a) high (b) low (c) optimum (d) any value
Last Answer : Ans: b
Description : For better COP of refrigerator, the pressure range corresponding to temperature in evaporator and condenser must be (a) small (b) high (c) equal (d) anything
Description : patient with rhumatic heart disease and had mitral valve stenosis Mitral vave diameter less than 1 mm In order to maintain COP what will happen : Left atrial hypertrophy and decrease ... dilatation with decrease pressure of contraction d- ventricle dilatation with decrease pressure of contraction .
Last Answer : Dilatation in the atrium with chamber hypertrophy
Description : The full form of MEPS A) Minimum energy protection standards C) minimum energy policies standard B) Minimum energy performance standards D) minimum efficiency performance standards
Last Answer : Minimum energy performance standards
Last Answer : Combined Opposition Party.
Description : Define the performance coefficient of a refrigerator. ?
Last Answer : : The ratio of heat removed from low temperature heat to work performed by an outside company is called the performance coefficient of the refrigerator.
Description : The coefficient of performance is the ratio of the refrigerant effect to the (a) heat of compression (b) work done by compressor (c) enthalpy increase in compressor (d) all of the above
Last Answer : Ans: d
Description : A refrigeration cycle operates between condenser temperature of + 27°C and evaporator temperature of- 23°C. TheCarnot coefficient of performance of cycle will be (a) 0.2 (b) 1.2 (c) 5 (d) 6
Last Answer : Ans: c
Description : When V-belt drive is used a safety device, its performance is affected by a) Variation in belt tention b) Increase in coefficient of friction as belt slippage increase c) Both (a) and (b) d) None of the above
Last Answer : c) Both (a) and (b)
Description : Define coefficient of performance.
Last Answer : Coefficient of Performance.: Working performance of any machine is usually expressed by output/input ratio known as efficiency. In refrigeration it is denoted by C.O.P. ( β ) . COP= refrigeration effect/ work input to produced R.E. β=RE/W
Description : A particle inside a hollow sphere of internal radius r with coefficient of friction 1/?3 can rest upto height of a.0.18 r b.0.435 r c.0.25 r d.0.134 r e.0.125 r
Last Answer : d. 0.134 r
Description : In the impact problems the following conditions must always be satisfied a.The total kinetic energy remains unchanged b.The total linear momentum remains unchanged c.The magnitude of the total linear ... is reduced by a factor proportional to the coefficient of restitution e.None of the above
Last Answer : b. The total linear momentum remains unchanged
Description : For perfectly elastic bodies, the value of the coefficient of restitution is a.1 b.0.372 c.0.5 d.Zero e.Any value between 0 and 1
Last Answer : a. 1
Description : A ball is dropped from a height of 2.25 m on a smooth floor and it rises to a height of 1 m after the first bounce. The coefficient of restitutions between the ball and the floor is a.107 dynes b.0.33 c.0.44 d.0.57 e.0.67
Last Answer : e. 0.67
Description : A uniform cylinder of weight W is rolling while slipping on a rough horizontal surface under the influence of a horizontal force. The force of friction between the cylinder and the surface is a. ... c.Indeterminate d.Determinate but depends on the acceleration of the cylinder e.None of the above
Last Answer : c. Indeterminate
Description : For perfectly elastic bodies the value of the coefficient of restitution is a.0.707 b.0.5 c.1 d.0.25 e.Zero
Last Answer : a. 0.707
Description : A car is travelling at 90 km/hour on a rough road where the coefficient of friction between the road and the tyre is 0.5. The distance the car will skid before stopping when the brakes are jammed suddenly would be a.127.4 m b.95.55 m c.63.7 m d.31.85 m e.90 m
Last Answer : c. 63.7 m
Description : The ideal angle of banking provided on roads a.Depends on (velocity)2 of vehicle b.Depends on the nature of road surface c.Depend on coefficient of friction between the road and the vehicle cantact point d.Depends on weight of the vehicle e.All above
Last Answer : a. Depends on (velocity)2 of vehicle
Description : A 5 m ladder of mass 25 kg is placed in a position where its inclination to a vertical wall is at 30?. A 100 kg man is to climb the ladder. If the coefficient of static friction is 0.25 the height along ladder at which the slipping will be induced would be a.2.4 m b.1.6 m c.0.8 m d.1.2 m e.0.5 m
Last Answer : c. 0.8 m
Description : A uniform cylinder of weight W is rolling while slipping on a rough horizontal surface under the influence of a horizontal force. The force of friction between the cylinder and the surface is a. ... on the acceleration of the cylinder d.107 dynes e.Proportional to the coefficient of static friction
Last Answer : c. Determinate but depends on the acceleration of the cylinder
Description : A car travelling at a speed of 60 km/hour is braked and comes to rest 6 seconds after the brakes are applied. The minimum coefficient of driction between the wheels and the road would be a.0.107 b.0.3 c.0.283 d.0.417 e.0.5
Last Answer : c. 0.283
Description : Which of the following bearing will have least coefficient of friction a.Single ball bearing b.Cylinderical roller bearing c.Self aligury bearing d.Thrust ball bearing e.Tapered bearing
Last Answer : e. Tapered bearing
Description : The coefficient of friction is a.The tangent of the angle between the normal reaction and direction of limiting friction b.The tangent of the angle between the normal reaction and the resultant ... e.The angle between the normal reaction and the resultant of normal reaction and the limiting friction
Last Answer : a. The tangent of the angle between the normal reaction and direction of limiting friction
Description : The coefficient of static friction will have the highest value in case of a.Mild steel and mild steel b.Mild steel and copper c.Cast iron and steel d.Rope and wood e.Any of the above loctions
Last Answer : d. Rope and wood
Description : A man wished to move a block of size 3 m x 3 m weighing 80 kg. The coefficient of friction between the block and the ground is 0.27. Which of the following methods should be used? a.Slide along the ground by pushing b.Ask for cranes c.Pull it d.Tip it over e.Lift it bodily
Last Answer : d. Tip it over
Description : A crate weighing 40 kg rests on a cart moving with an acceleration W. The coefficient of friction between the cart and the crate is a.2.45 m/sec2 b.4.00 m/sec2 c.0.25 m/sec2 d.4.16 m/sec2 e.1.25 m/sec2
Last Answer : a. 2.45 m/sec2
Description : A weight of 4.9 N rests on a rough horizontal floor that has a coefficient of friction of 0.5. If g = 9.8 m/s2, the smallest horizontal force that gives the weight an acceleration of 4m/s2 is most nearly a.2.5 N b.3 N c.2 N d.4.5 N e.4.9 N
Last Answer : d. 4.5 N
Description : What Is Coefficient Of Contraction?
Last Answer : Coefficient of contraction is the ratio of area of jet at vena contracta to the area of orifice. The typical value may be taken as 0.64 for a sharp orifice (concentric with the flow channel). The smaller the value, the more effect the vena contracta has.
Description : For most solids, the coefficient of volume expansion is _________ the coefficient of linear expansion. a. unrelated to b. proportional to c. twice d. three times
Last Answer : three times
Description : What is a measure of the ability of a material to conduct heat? A. Specific heat capacity B. Coefficient of thermal expansion C. Coefficient of thermal conductivity D. Thermal conductivity
Last Answer : Thermal conductivity
Description : What are the important operational performance parameters in design of fuel firing equipment ?
Last Answer : Fuel flexibility, electrical load following capability, reliability, availability, and maintenance ease.
Description : Differential lock in tractor is used to improve a) Lateral stability b) Braking performance c) Hydraulic lift d) Traction of a wheel
Last Answer : Braking performance
Last Answer : ans d
Description : is the measure of whether a plant is now using more or less energy to manufacture its product than it did in the past. a) Total Dissolved Solids (TDS). c) Plant Energy Performance (PEP) b) Revolutions Per Minute (RPM) d) Option (a) and (b)
Last Answer : Plant Energy Performance (PEP)
Description : is the measure of whether a plant is now using more or less energy to manufacture its product than it did in the past. a) Total Dissolved Solids (TDS) b) Plant Energy Performance (PEP) c) Revolutions Per Minute (RPM) d) Option (a) and (b)
Description : The tool used for performance assessment and logical evaluation of avenues for improvement in Energy management and audit is a) Fuel substitution c) Energy pricing b) Monitoring and verification d) Bench marking
Last Answer : Bench marking