Description : is an assembly comparing of fingers, knife guides on wearing plates and shoe. a) Cutter bar b) Knife section c) Pitman d) Shoe
Last Answer : Cutter bar
Description : It is always provided on each end of the cutter bar to regulate the height of cut and to provide easy and smooth sliding of the cutter bar on the land. b. Plate c. pitman d. None of above
Last Answer : Ans- b. shoe
Description : are the labelling of cutter bar. a) Shoe, ledger plate, wearing plate, knife, knife section, etc. b) Star wheel, engine, cage wheel, etc. c) both A & B d) Conveyor belt, cutter bar, rivers, etc
Last Answer : Shoe, ledger plate, wearing plate, knife, knife section, etc.
Description : Play in bearings and worn knife head holders caused due to in cutter bar. A) Pitman B) Breaking of knives. C) Knife head. D) Grass board.
Last Answer : Breaking of knives.
Description : The energy of expanding gas is transferred by piston to connecting rod through a. Crank pin b. Gudgeon pin c. Bearing d. Crankcase (Ans:b)
Last Answer : Which of the following is not used in four stroke compression-ignition (CI) engines? a. Fuel pump b. Spark plug c. Fuel injector d. Inlet and outlet Valves (Ans:b)
Description : which of the following components helps to limit the front-to-back movement of the crankshaft? -General Knowledge
Last Answer : The flywheel helps to limit the front-to-back movement of the crankshaft.
Description : In a slider crank mechanism, the crank is rotating at 200 rpm. If length of connecting rod is 8 mts and crank shaft is 2 mts, velocity of crosshead at 30? rotation of crank shaft equals. a.30.2 m/s b.33.2 m/s c.35.8 mts/s d.107 dynes e.25.5 m/s
Last Answer : e. 25.5 m/s
Description : It is the link between the knife and crank wheel of the mower. a. connecting rod c. rod d. None of above
Last Answer : Ans- b. Pitman
Description : The conventional type of Mower consists of which of the following a) Wearing Plate b) Nozzle c) Air Chamber d) None of the above
Last Answer : Wearing Plate
Description : Choke in a I.C. engine is used to control a) Camshaft speed b) Specific fuel consumption c) Air fuel mixture d) Crankshaft speed Ans. c
Last Answer : ans c
Description : Identify the properties of material used for connecting rod with justification
Last Answer : Answer: 1. There are some materials that are commonly used in connecting rods such as alloys of steel, aluminum and titanium. Mostly connecting rods are made by forged steel. It is widely use ... times lighter than carbon steel. It is because density of Al360 is very less compared to carbon steel
Description : Cutter bar is made up of which material a) High grade steel. b) Low carbon alloy steel. c) Platinum. d) High speed tool steel
Last Answer : High grade steel
Description : 2. In Activity 13.7, how do we think the displacement of rod AB will be affected if (i) current in rod AB is increased; (ii) a stronger horse-shoe magnet is used; and (iii) length of the rod AB is increased? -Physics-10
Last Answer : A current carrying conductor when placed in a magnetic field experiences force. The magnitude of this force will increase with the increase in the amount of current, length of conductor and the strength ... AB is increased Stronger horse shoe magnet is used When the length of the rod AB increases
Description : In your opinion, which is better, Pitman or Gregg shorthand?
Last Answer : I personally prefer Gregg, but this purely for aesthetic purposes.
Description : Which of the following is not a part of the Blake jaw crusher? (A) Hanger (B) Check plates (C) Toggles (D) Pitman
Last Answer : (A) Hanger
Description : What kind of shoe is Selena Gomez wearing in Another Cinderella Story?
Last Answer : short boots
Description : Can anyone give me some guidance with a statics 3-pinned arch problem? (see details)
Last Answer : answer:Sounds like homework for Engineering Statics. Are you in an Engineering class?
Description : What is that red and green thing pinned on BBC presenters occasionally?
Last Answer : That looks like a poppy that people wear around Remembrance Day.
Description : You are stuck in a room. On the door is a keypad with all the letters of the alphabet and the enter button. The word is 7 letters long. To your left, is a table with a note. The note reads: ... the note upon the table, remove a letter and you will be free. What is the code to escape? -Riddles
Last Answer : The code is science After solving for the first note, you will get sciesnce. If you don't understand why, go to the Periodic Table of the Elements and find these elements there. From the ... with this my self when I was looking at the periodic table. Thank you for reading my Escape Room.
Description : I can't loosen the wheel bolts. Is it possible to repair a pinned wheel without taking it off?
Last Answer : Yes, it is possible. A wick is used to seal the hole. Personally, I don't consider this a tire repair. http://www.ferdus.cz/sekce/353-opravne-knoty
Description : Who pinned the third star on General Patton's uniform?
Last Answer : Early in the war, General Eisenhower pinned the third star onGeneral Patton's uniform. This was a promotion for Patton, who wasthen a lieutenant general.
Description : A beam of length L is pinned at both ends and is subjected to a concentrated bending couple of moment M at its centre. The maximum bending moment in the beam is (A) M (B) M/2 (C) M/3 (D) ML/2
Last Answer : (A) M
Description : What way do the rod bearing caps go onto the connecting rod on a Chevy 350 motor?
Last Answer : The notches for the bearings to lock from spinning are both onthe same side.
Description : What are John deere 2010 connecting rod torque specs?
Last Answer : Need answer
Description : Addition of 2% nickel in steel makes it suitable for making (A) Electronic valves (B) Boiler plates, rivets etc. (C) Turbine blades (D) Connecting rod
Last Answer : (B) Boiler plates, rivets etc.
Description : Maximum rod connecting limit by using knuckle joint is . A. 2 B. 3 C. 4 D. 5
Last Answer : B. 3
Description : The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)
Last Answer : (A) Approaches yield point
Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three
Last Answer : (D) All the three
Description : Connecting rod of two stroke engine is subjected to A. Compressive load B. Tensile load C. Both compressive and tensile load D. None of the above
Last Answer : A. Compressive load
Description : Connecting rod of four stroke engine is subjected to A. Compressive load B. Tensile load C. Both compressive and tensile load D. None of the above
Last Answer : C. Both compressive and tensile load
Description : Connecting rod generally have A)t-shape b)angle shape C)i-shape d)flst-shape
Last Answer : C)i-shape
Description : State the functions and materials of following engine components: (i) Piston (ii) Connecting rod (iii)Crank shaft (iv)Exhaust manifold
Last Answer : Engine components Material Functions Piston Cat aluminum alloy To transmit the force of explosion to the crankshaft. To form seal so that the high pressure gases in ... atmosphere through the exhaust pipe after combustion stroke is completed. To keep back pressure minimum.
Description : Show the following components in an engine with neat sketch: piston, connecting rod, valves, spark plug
Last Answer : OR
Description : Apply proper heat treatment process for manufacturing connecting rod of an engine.
Last Answer : Answer: The connecting rod may either be cast or forged when created and may also include allowable secondary alloy elements. The normalizing step includes heating a rough connecting rod to ... , not throughout the entire rod, but instead only where high hardness is required functionally.
Description : State functions and name suitable materials for connecting rod. Select suitable crosssection for connecting rod with justification
Last Answer : Functions of connecting rod: A connecting rod, also called a con rod, is the part of a piston engine which connects the piston to the crankshaft. Together with the crank, the connecting rod ... a connecting rod may have rectangular section. For slow speed engines, circular sections may be used.
Description : List basic design requirement of connecting rod.
Last Answer : In designing a connecting rod for I.C. engine, the following points should be taken into consideration : Strength to withstand the high inertia forces. Minimum mass to minimise ... undue wear. High speed reciprocation without noise. Rigid construction to withstand mechanical distortion.
Description : In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right ... , 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)
Last Answer : a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5)
Description : The distance of a given tool tip from the surface of workpiece is known as….. a.Tool length b.Tool length offset H c.Cutter radius d.Compensation
Last Answer : b.Tool length offset H
Description : Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b
Last Answer : ans b
Description : Registration of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. a
Last Answer : ans a
Description : cutter bar knife a) triangular shape b) square shape c) trapezoidal shape d) curved shape Ans. c
Description : Registration of a cutter bar means a) Centre of knife must stop in the centre of guard on each stroke b) Centre of knife should be ahead of guard c) Centre of knife should be behind the guard d) Centre of knife should be at the end of the guard
Description : The cutter bar is set at about to the direction of motion in order to overcome the back-pushing action of the crops. a. 90° with inward lead of 2° c. 92° with inward lead of 2° d. None of above
Last Answer : Ans- b. 88° with inward lead of 2°
Description : Cutter Bar made of a) Copper b) High Grade Steel c) Cast iron d) None of the above
Last Answer : High Grade Steel
Description : is part of the Cutter bar is shaped in Triangular shape with two cutting edges a) Knife head b) Knife back c) Grass board d) Knife Section
Last Answer : <!-- [endif] -->Knife Section
Description : In vertical conveyor reaper, the crop to be harvested are guided by a) Star wheel b) Reel c) Row divider d) Cutter bar
Last Answer : Star wheel
Description : How much of lead degree is given if the cutter is set at 88 degree? a) 2-degree b) 4 degree c) 3-degree d) 5 degree
Last Answer : 2-degree
Description : is the length of cutter bar which is recommended as per the standard of design of it. a) 4cm b) 6cm c) 2cm d) 3cm
Last Answer : 2cm
Description : At what degree does the cutter bar is set for achieving the object ? a) 96 b) 88 c) 69 and half. d) 105
Last Answer : 88
Description : Which type of earthing is also called as 'fire earthing'? A. Plate earthing B. Rod earthing C. Strip earthing
Last Answer : Option B is right (ROD EARTHING )