Shoe, ledger plate, wearing plate, knife, knife section, etc.
Description : is an assembly comparing of fingers, knife guides on wearing plates and shoe. a) Cutter bar b) Knife section c) Pitman d) Shoe
Last Answer : Cutter bar
Description : In vertical conveyor reaper, the crop to be harvested are guided by a) Star wheel b) Reel c) Row divider d) Cutter bar
Last Answer : Star wheel
Description : type of connecting rod which is pinned to the crankshaft with the help of a pin, which helps to transmit the cut material. a) Pitman b) Cutter bat c) Shoe d) Wearing plate
Last Answer : Pitman
Description : Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b
Last Answer : ans b
Description : Registration of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. a
Last Answer : ans a
Description : cutter bar knife a) triangular shape b) square shape c) trapezoidal shape d) curved shape Ans. c
Last Answer : ans c
Description : Registration of a cutter bar means a) Centre of knife must stop in the centre of guard on each stroke b) Centre of knife should be ahead of guard c) Centre of knife should be behind the guard d) Centre of knife should be at the end of the guard
Description : is part of the Cutter bar is shaped in Triangular shape with two cutting edges a) Knife head b) Knife back c) Grass board d) Knife Section
Last Answer : <!-- [endif] -->Knife Section
Description : Play in bearings and worn knife head holders caused due to in cutter bar. A) Pitman B) Breaking of knives. C) Knife head. D) Grass board.
Last Answer : Breaking of knives.
Description : enght of cutter bar for the tractor operated mower or vertical conveyor reaper is..... (a) 1.5-3.0m (b) 3.0-4.5m (c)4.5-5.5m (d) >5.5m
Last Answer : (a) 1.5-3.0m
Description : It is always provided on each end of the cutter bar to regulate the height of cut and to provide easy and smooth sliding of the cutter bar on the land. b. Plate c. pitman d. None of above
Last Answer : Ans- b. shoe
Description : is not well register, there is unbalance load, uneven harvesting and exclusive clogging of crops on the knife A) Vertical conveyor reaper B) MOVER C) Reaper binder D) Potato digger elevator.
Last Answer : MOVER
Description : __________ conveyor is the most suitable for short distance transportation of non-abrasive loose materials like garbage, grain, food wastes etc. (A) Flight (B) Screw (C) Drag (D) Belt
Last Answer : (A) Flight
Description : The capacity of a belt conveyor depends upon two factors. If one is the cross-section of the load, the other is the __________ of the belt. (A) Speed (B) Thickness (C) Length (D) None of these
Last Answer : (A) Speed
Description : Width and speed of a conveyor belt depends upon the __________ of the material. (A) Lump size (B) Bulk density (C) Both (A) & (B) (D) Neither (A) nor (B
Last Answer : (C) Both (A) & (B)
Description : Hot, lumpy & abrasive materials are best transported by using a/an __________ conveyor. (A) Apron (B) Belt
Last Answer : (A) Apron
Description : Pick out the correct statement. (A) Noise from ball mills can be dealt with by fibre glass lined enclosures (B) Noise from vibrating chutes can be reduced by lining the metallic chute with rubber (C) Noise ... cloth conveyor belts and rubber/plastic covered metallic rollers (D) All (A), (B) & (C)
Last Answer : (D) All (A), (B) & (C)
Description : Develop a ladder diagram for to control conveyor belt motor equipped with the: (i) Counter of item. (ii) Start & Stop functions. (iii) Change of direction function.
Last Answer : Forward: Reverse:
Description : State whether the Diesel Engine Driven Monoset Pumps for agricultural purposes have been notified under the voluntary labelling. A. True. B. False.
Last Answer : true
Description : has a long handled tool and a 120 mm diameter star wheel a) Engine operated weeder b) Cono weeder for paddy c) Dry land weeder d) Sweep
Last Answer : Dry land weeder
Description : Depth of working of a tillage implement is controlled by a) Furrow Wheel b) Gauge Wheel c) Cage Wheel d) Star Wheel
Last Answer : d) Star Wheel
Description : The cutter bar is set at about to the direction of motion in order to overcome the back-pushing action of the crops. a. 90° with inward lead of 2° c. 92° with inward lead of 2° d. None of above
Last Answer : Ans- b. 88° with inward lead of 2°
Description : Cutter Bar made of a) Copper b) High Grade Steel c) Cast iron d) None of the above
Last Answer : High Grade Steel
Description : Cutter bar is made up of which material a) High grade steel. b) Low carbon alloy steel. c) Platinum. d) High speed tool steel
Last Answer : High grade steel
Description : is the length of cutter bar which is recommended as per the standard of design of it. a) 4cm b) 6cm c) 2cm d) 3cm
Last Answer : 2cm
Description : At what degree does the cutter bar is set for achieving the object ? a) 96 b) 88 c) 69 and half. d) 105
Last Answer : 88
Description : Knife clips are placed with wearing plates spaced from cm apart. A) 10-20cm B) 60-90cm C) 15-25cm D) 20-30cm
Last Answer : 20-30cm
Description : Knife clips are placed with wearing plates spaced to apart a) 20 to 30 b) 45 to 60 c) 20 to 35 d) 30 to 40
Last Answer : 20 to 30
Description : It is the link between the knife and crank wheel of the mower. a. connecting rod c. rod d. None of above
Last Answer : Ans- b. Pitman
Description : From the following which material handling equipment is used in ladder layout of FMS a.Conveyor systems b.AGVS c.Both A & B d.None of the above
Last Answer : c.Both A & B
Description : Where can I buy a belt conveyor system?
Last Answer : There are several different sites online where you can purchase a conveyor belt system. One such site is conveyorbelts.com. A wide selection is offered.
Description : __________ conveyor is the most suitable for long distance transportation of cold, non-abrasive granular/irregular shape/fine materials. (A) Bucket (B) Belt (C) Screw (D) Apron
Last Answer : (B) Belt
Description : Which of the following conveyors cannot be recommended for transportation of abrasive materials? (A) Belt conveyor (B) Apron conveyor (C) Flight conveyor (D) Chain conveyor
Last Answer : (C) Flight conveyor
Description : Handling of ashes and similar materials can be done best by a __________ conveyor. (A) Flight (B) Drag or slat (C) Belt (D) Ribbon
Last Answer : (B) Drag or slat
Description : A belt conveyor used for the transportation of materials can (A) Run upto 1 km (B) Travel at a speed upto 300 metres/minute (C) Handle materials upto 5000 tons/hr (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : The maximum slope of a belt conveyor can be (A) 15° (B) 30° (C) 45° (D) 60
Last Answer : (B) 30°
Description : The most suitable equipment for the transportation of 200 mesh size particles is a (A) Bucket elevator (B) Pneumatic conveyor (C) Screw conveyor (D) Belt conveyor
Last Answer : (B) Pneumatic conveyor
Description : For the transportation of ultrafine particles, the equipment used is a __________ conveyor. (A) Belt (B) Pneumatic (C) Screw (D) None of these
Last Answer : (B) Pneumatic
Description : Dry powdery solid materials are transported by a __________ conveyor. (A) Belt (B) Bucket (C) Screw (D) None of these
Last Answer : (C) Screw
Description : Which is the most suitable conveyor for transportation of sticky material? (A) Apron conveyor (B) Belt conveyor (C) Screw conveyor (D) Pneumatic conveyo
Last Answer : (C) Screw conveyor
Description : For transporting pasty material, one will use a/an (A) Apron conveyor (B) Belt conveyor (C) Screw conveyor (D) Bucket elevator
Description : Which of the following mechanical conveyors does not come under the division ‘carriers’? (A) Belt conveyor (B) Bucket elevator (C) Screw conveyor
Description : What type of bearing will you recommend for use in the conveyor belt roller? (a) Ball-bearing (b) Roller bearing (c) Magnetic bearing (d) None of the mentioned
Last Answer : (b) Roller bearing
Description : Which of the following material handling equipments is not suitable for moving materials in varying paths? (A) Hand trolley (B) Belt conveyor (C) Crane (D) Truck
Last Answer : (B) Belt conveyor
Description : The S & L activity has been identified as a key activity for energy efficiency improvement which stands for A. Standards & Listening. B. Standards & Labelling. C. Standards & Logistics. D. Standards & Lateral.
Last Answer : Standards & Labelling.
Description : The Bureau of Energy Efficiency initiated the standard and labelling programme for equipments & appliances in A. 2001. B. 2004. C. 2006. D. 2008.
Last Answer : 2006
Description : Do I really need a bagel cutter or can I just use a knife?
Last Answer : A bagel cutter isn't necessary to cut a bagel, but it can be slightly safer than simply using a knife. This may be important for someone who has poor motor skills, such as an elderly person or ... to spend the money, find space to store it, and would actually use it before deciding to purchase.
Description : What are the advantages of using a pastry cutter instead of a knife?
Last Answer : The advantages of using a pastry cutter instead of a knife are that the crust is more likely to self rise and it makes the crust flakier. It is a very useful tool!
Description : Gummy & sticky materials like molasses, sugar etc. are besttransported/handled by using a __________ conveyor. (A) Drag (B) Ribbon (C) Screw (D) Slat
Last Answer : (B) Ribbon
Description : The two types of cylinders used on power wheat threshers are 1. Serrated disc and rasp bar 2.gears and belt pulleys 3. belt pulleys and chains 4 none of the above
Last Answer : ans 2