Ans- b. shoe
Description : type of connecting rod which is pinned to the crankshaft with the help of a pin, which helps to transmit the cut material. a) Pitman b) Cutter bat c) Shoe d) Wearing plate
Last Answer : Pitman
Description : Play in bearings and worn knife head holders caused due to in cutter bar. A) Pitman B) Breaking of knives. C) Knife head. D) Grass board.
Last Answer : Breaking of knives.
Description : is an assembly comparing of fingers, knife guides on wearing plates and shoe. a) Cutter bar b) Knife section c) Pitman d) Shoe
Last Answer : Cutter bar
Description : are the labelling of cutter bar. a) Shoe, ledger plate, wearing plate, knife, knife section, etc. b) Star wheel, engine, cage wheel, etc. c) both A & B d) Conveyor belt, cutter bar, rivers, etc
Last Answer : Shoe, ledger plate, wearing plate, knife, knife section, etc.
Description : Registration of a cutter bar means a) Centre of knife must stop in the centre of guard on each stroke b) Centre of knife should be ahead of guard c) Centre of knife should be behind the guard d) Centre of knife should be at the end of the guard
Last Answer : ans a
Description : knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height
Last Answer : a)Increase the co-efficient of friction between crop stalk machine
Description : Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b
Last Answer : ans b
Description : Registration of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. a
Description : cutter bar knife a) triangular shape b) square shape c) trapezoidal shape d) curved shape Ans. c
Last Answer : ans c
Description : The cutter bar is set at about to the direction of motion in order to overcome the back-pushing action of the crops. a. 90° with inward lead of 2° c. 92° with inward lead of 2° d. None of above
Last Answer : Ans- b. 88° with inward lead of 2°
Description : Cutter Bar made of a) Copper b) High Grade Steel c) Cast iron d) None of the above
Last Answer : High Grade Steel
Description : is part of the Cutter bar is shaped in Triangular shape with two cutting edges a) Knife head b) Knife back c) Grass board d) Knife Section
Last Answer : <!-- [endif] -->Knife Section
Description : In vertical conveyor reaper, the crop to be harvested are guided by a) Star wheel b) Reel c) Row divider d) Cutter bar
Last Answer : Star wheel
Description : Cutter bar is made up of which material a) High grade steel. b) Low carbon alloy steel. c) Platinum. d) High speed tool steel
Last Answer : High grade steel
Description : is the length of cutter bar which is recommended as per the standard of design of it. a) 4cm b) 6cm c) 2cm d) 3cm
Last Answer : 2cm
Description : At what degree does the cutter bar is set for achieving the object ? a) 96 b) 88 c) 69 and half. d) 105
Last Answer : 88
Description : o over come the rear ward deflection the load given to outer end of the cutter bar is about..... (a)1.57cm/m (b) 2.0cm/m (b)3.0cm/m (d) 3.5cm/m
Last Answer : b) 2.0cm/m
Description : In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right ... , 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)
Last Answer : a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5)
Description : In case the factor of safety against sliding is less than 1.5, a portion of slab is constructed downwards at the end of the heel slab, which is known as (A) A key (B) A cut-off wall (C) A rib (D) All the above
Last Answer : Answer: Option D
Description : A block A is dropped down a smooth inclined plane, while another identical block B is released for free fall from the same height a.block A will have higher velocity than block B while hitting the ... . c.both will hit the ground simultaneously d.block A will hit the ground earlier e.107 dynes
Last Answer : b. block B will hit the ground earlier.
Description : A ball is dropped from a height of 2.25 m on a smooth floor and it rises to a height of 1 m after the first bounce. The coefficient of restitutions between the ball and the floor is a.107 dynes b.0.33 c.0.44 d.0.57 e.0.67
Last Answer : e. 0.67
Description : A boy sitting in a rail road car throws a ball straight up into the air. The ball will fall back into his hands when the rail road car is a.moving at constant velocity b.accelerating ... inclined plane, while another identical block B is released for free fall from the same height e.decelerating
Last Answer : a. moving at constant velocity
Description : The cutter bar of a tractor operated on owner makes strokes/min (a) 400 – 500 (b) 500 – 750 (c) 800 – 1200 (d) 1250 – 1500
Last Answer : (c) 800 – 1200
Description : The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links
Last Answer : D. Between the two lower Links
Description : The cutter bar of a tractor operated mower ordinarily makes: A. 800-1200 strokes/min B. 1600-2000 strokes/min C. 2400-2800 strokes/min D. 3200-3600 strokes/min
Last Answer : A. 800-1200 strokes/min
Description : enght of cutter bar for the tractor operated mower or vertical conveyor reaper is..... (a) 1.5-3.0m (b) 3.0-4.5m (c)4.5-5.5m (d) >5.5m
Last Answer : (a) 1.5-3.0m
Description : Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm
Last Answer : a)400-550 rpm
Description : Pick up reels are very effective in :- a) Cutting of upright crops b) Lifting of lodged (down) crops ahead of cutter bar C) Both (a) and (b) are true d) None of the above
Last Answer : C) Both (a) and (b) are true
Description : Speed of the cutter bar in case of combine (grain) is :- a) 400 – 550 rpm b) 500 – 800 rpm C) 800 - 1000 rpm d) 1000 – 1200 rpm
Last Answer : a) 400 – 550 rpm
Description : Bearings for plate girders are -- a) roller bearing b) sliding bearings c) centralised articulated bearings* d) None of the above
Last Answer : c) centralised articulated bearings*
Description : What is the name given to a region where one plate of the earth's crust is sliding under another?
Last Answer : ANSWER: SUBDUCTION ZONE
Description : In your opinion, which is better, Pitman or Gregg shorthand?
Last Answer : I personally prefer Gregg, but this purely for aesthetic purposes.
Description : Which of the following is not a part of the Blake jaw crusher? (A) Hanger (B) Check plates (C) Toggles (D) Pitman
Last Answer : (A) Hanger
Description : A ball is allowed to fall freely from a height of 3 metres on to a fixed plate. If the successive rebound heights are h1, h2, h3 a.5 metres b.4.25 metre c.0.5 metre d.1 metre e.Zero
Last Answer : a. 5 metres
Description : The distance of a given tool tip from the surface of workpiece is known as….. a.Tool length b.Tool length offset H c.Cutter radius d.Compensation
Last Answer : b.Tool length offset H
Description : How much of lead degree is given if the cutter is set at 88 degree? a) 2-degree b) 4 degree c) 3-degree d) 5 degree
Last Answer : 2-degree
Description : Prismatic compass is considered more accurate than a surveyor's compass, because (A) It is provided with a better magnetic needle (B) It is provided with a sliding glass in the object vane ( ... whole circle bearings (D) It is provided with a prism to facilitate reading of its graduated circle
Last Answer : (D) It is provided with a prism to facilitate reading of its graduated circle
Description : Parapet walls along hill roads, are provided (A) To retain the back filling (B) To prevent the hill from sliding (C) To prevent the wheels of the vehicle from coming on the retaining wall (D) None of these
Last Answer : Answer: Option C
Description : Pick up the incorrect statement from the following: (A) The retaining wall should be structurally capable to resist the applied earth pressure (B) The section of the retaining wall should be so ... off water from the earth retained, weep holes are provided near the top of the retaining wall
Description : Pick up the correct statement from the following: (A) Louvered door is generally provided in bath rooms (B) Flush door is generally provided in dining room (C) Revolving door is generally provided in cinema halls (D) Sliding door is generally provided in show rooms
Description : Mostly long span rail-cum road bridges are provided with a) rocker & roller bearings b) segmental roller with oil bath* c) Sliding bearings d) centralised bearings
Last Answer : b) segmental roller with oil bath
Description : A metering mechanism that does not required cut-off device is: A. Inclined plate B. Vertical plate C. Horizontal plate D. All are correct
Last Answer : All are correct
Description : is not the component of sprayers. a) Swirl plate b) Filter c) Cut-off value d) Pump
Last Answer : Pump
Description : How do you make a great cut in glass easily without a glass cutter?
Last Answer : Why don’t you want to use a glass cutter? That is the only thing I can think of to cut glass with.
Description : Is there a special cutter used to cut foam?
Last Answer : If you have ever cut foam you know that it is very hard to cut. The most commonly used tool is an electric knife to cut foam with ease. Yes, there is a special cutter called a hot-wire ... to cut foam-based materials. This special cutter uses heat emanating the metal wire to cut the foam material.
Description : What is the hardest things a bolt cutter can cut?
Last Answer : It will depend on the quality of the bolt cutter. It should be able to cut anything similar to a bolt of chain it was designed for. Some really good ones might be able to cut rebar.
Description : Automatic voltage regulators provided on switchboards function to _____________. A. regulate the AC load on the generator B. protect the switchboard from high voltage C. govern prime mover speed to control voltage D. vary the field excitation to the generators
Last Answer : Answer: D
Description : Blow off cock is provided in steam boiler to (A) Guard the boiler in case of abnormal rise in steam pressure (B) Drain out water and sludge during its repair (C) Regulate the supply of water in boiler (D) Put out the fire in the furnace when the water level in the boiler falls to unsafe limit
Last Answer : (B) Drain out water and sludge during its repair
Description : The work done in sliding a block of weight of 50 kg up a plane inclined at an angle of 30? to the horizontal so that the block is lifted through 1 m ( a.More than 50 kgm b.50 kgm c.Less than 5 kgm d.15 kgm only e.None of the above
Last Answer : a. More than 50 kgm
Description : The principle of conservation of energy cannot be applied in case of a.Flow of heat through a metal b.Ideal flow of water in a pipe c.Simple pendulum d.Sliding of a particle along inclined plane with friction e.A particle moving in gravitational field
Last Answer : e. A particle moving in gravitational field