is an assembly comparing of fingers, knife guides on wearing plates and shoe. a) Cutter bar b) Knife section c) Pitman d) Shoe

is an assembly comparing of fingers, knife guides on wearing plates and shoe. a) Cutter bar b) Knife section c) Pitman d) Shoe
by

1 Answer

Answer :

Cutter bar
by

Related questions

are the labelling of cutter bar. a) Shoe, ledger plate, wearing plate, knife, knife section, etc. b) Star wheel, engine, cage wheel, etc. c) both A & B d) Conveyor belt, cutter bar, rivers, etc

Description : are the labelling of cutter bar. a) Shoe, ledger plate, wearing plate, knife, knife section, etc. b) Star wheel, engine, cage wheel, etc. c) both A & B d) Conveyor belt, cutter bar, rivers, etc

Last Answer : Shoe, ledger plate, wearing plate, knife, knife section, etc.

type of connecting rod which is pinned to the crankshaft with the help of a pin, which helps to transmit the cut material. a) Pitman b) Cutter bat c) Shoe d) Wearing plate

Description : type of connecting rod which is pinned to the crankshaft with the help of a pin, which helps to transmit the cut material. a) Pitman b) Cutter bat c) Shoe d) Wearing plate

Last Answer : Pitman 

Play in bearings and worn knife head holders caused due to in cutter bar. A) Pitman B) Breaking of knives. C) Knife head. D) Grass board.

Description : Play in bearings and worn knife head holders caused due to in cutter bar. A) Pitman B) Breaking of knives. C) Knife head. D) Grass board.

Last Answer : Breaking of knives.

It is always provided on each end of the cutter bar to regulate the height of cut and to provide easy and smooth sliding of the cutter bar on the land. b. Plate c. pitman d. None of above

Description : It is always provided on each end of the cutter bar to regulate the height of cut and to provide easy and smooth sliding of the cutter bar on the land. b. Plate c. pitman d. None of above

Last Answer : Ans-    b. shoe

Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b

Description : Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b

Last Answer : ans b

Registration of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. a

Description : Registration of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. a

Last Answer : ans a

cutter bar knife a) triangular shape b) square shape c) trapezoidal shape d) curved shape Ans. c

Description : cutter bar knife a) triangular shape b) square shape c) trapezoidal shape d) curved shape Ans. c

Last Answer : ans c

Registration of a cutter bar means a) Centre of knife must stop in the centre of guard on each stroke b) Centre of knife should be ahead of guard c) Centre of knife should be behind the guard d) Centre of knife should be at the end of the guard

Description : Registration of a cutter bar means a) Centre of knife must stop in the centre of guard on each stroke b) Centre of knife should be ahead of guard c) Centre of knife should be behind the guard d) Centre of knife should be at the end of the guard

Last Answer : ans a

is part of the Cutter bar is shaped in Triangular shape with two cutting edges a) Knife head b) Knife back c) Grass board

Description : is part of the Cutter bar is shaped in Triangular shape with two cutting edges a) Knife head b) Knife back c) Grass board d) Knife Section

Last Answer :   <!-- [endif] -->Knife Section

Knife clips are placed with wearing plates spaced from cm apart. A) 10-20cm B) 60-90cm C) 15-25cm D) 20-30cm

Description : Knife clips are placed with wearing plates spaced from cm apart. A) 10-20cm B) 60-90cm C) 15-25cm D) 20-30cm

Last Answer :  20-30cm

Knife clips are placed with wearing plates spaced to apart a) 20 to 30 b) 45 to 60 c) 20 to 35 d) 30 to 40

Description : Knife clips are placed with wearing plates spaced to apart a) 20 to 30 b) 45 to 60 c) 20 to 35 d) 30 to 40

Last Answer : 20 to 30

A mower knife is said to be in proper registration when the knife section stops in the ……………..of its guard ( fingers ) on every stroke a. offset c. inclined d. None of above

Description : A mower knife is said to be in proper registration when the knife section stops in the ……………..of its guard ( fingers ) on every stroke a. offset c. inclined d. None of above

Last Answer : <!-- [if !supportLists] -->a.  <!-- [endif] -->Ans-                     b. centre  

Which of the following is not a part of the Blake jaw crusher? (A) Hanger (B) Check plates (C) Toggles (D) Pitman

Description : Which of the following is not a part of the Blake jaw crusher? (A) Hanger (B) Check plates (C) Toggles (D) Pitman

Last Answer : (A) Hanger

It is a mower with a knife made of several serrated triangular sections that reciprocate against stationary fingers. a. Rotary mower c. Cylinder mower. d. None of above

Description : It is a mower with a knife made of several serrated triangular sections that reciprocate against stationary fingers. a. Rotary mower c. Cylinder mower. d. None of above

Last Answer : Ans-   b. Reciprocating mower  

The cutter bar is set at about to the direction of motion in order to overcome the back-pushing action of the crops. a. 90° with inward lead of 2° c. 92° with inward lead of 2° d. None of above

Description : The cutter bar is set at about to the direction of motion in order to overcome the back-pushing action of the crops. a. 90° with inward lead of 2° c. 92° with inward lead of 2° d. None of above

Last Answer : Ans-         b. 88° with inward lead of 2°  

Cutter Bar made of a) Copper b) High Grade Steel c) Cast iron d) None of the above

Description : Cutter Bar made of a) Copper b) High Grade Steel c) Cast iron d) None of the above

Last Answer : High Grade Steel

In vertical conveyor reaper, the crop to be harvested are guided by a) Star wheel b) Reel c) Row divider d) Cutter bar

Description : In vertical conveyor reaper, the crop to be harvested are guided by a) Star wheel b) Reel c) Row divider d) Cutter bar

Last Answer : Star wheel

Cutter bar is made up of which material a) High grade steel. b) Low carbon alloy steel. c) Platinum. d) High speed tool steel

Description : Cutter bar is made up of which material a) High grade steel. b) Low carbon alloy steel. c) Platinum. d) High speed tool steel

Last Answer : High grade steel

is the length of cutter bar which is recommended as per the standard of design of it. a) 4cm b) 6cm c) 2cm d) 3cm

Description : is the length of cutter bar which is recommended as per the standard of design of it. a) 4cm b) 6cm c) 2cm d) 3cm

Last Answer : 2cm

At what degree does the cutter bar is set for achieving the object ? a) 96 b) 88 c) 69 and half. d) 105

Description : At what degree does the cutter bar is set for achieving the object ? a) 96 b) 88 c) 69 and half. d) 105

Last Answer : 88

Do I really need a bagel cutter or can I just use a knife?

Description : Do I really need a bagel cutter or can I just use a knife?

Last Answer : A bagel cutter isn't necessary to cut a bagel, but it can be slightly safer than simply using a knife. This may be important for someone who has poor motor skills, such as an elderly person or ... to spend the money, find space to store it, and would actually use it before deciding to purchase.

What are the advantages of using a pastry cutter instead of a knife?

Description : What are the advantages of using a pastry cutter instead of a knife?

Last Answer : The advantages of using a pastry cutter instead of a knife are that the crust is more likely to self rise and it makes the crust flakier. It is a very useful tool!

In power saving guides "more stars more savings". A) True B) false

Description : In power saving guides "more stars more savings". A) True B) false

Last Answer : true

The cutter bar of a tractor operated on owner makes strokes/min (a) 400 – 500 (b) 500 – 750 (c) 800 – 1200 (d) 1250 – 1500

Description : The cutter bar of a tractor operated on owner makes strokes/min (a) 400 – 500 (b) 500 – 750 (c) 800 – 1200 (d) 1250 – 1500

Last Answer : (c) 800 – 1200

The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Description : The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Last Answer : D. Between the two lower Links

The cutter bar of a tractor operated mower ordinarily makes: A. 800-1200 strokes/min B. 1600-2000 strokes/min C. 2400-2800 strokes/min D. 3200-3600 strokes/min

Description : The cutter bar of a tractor operated mower ordinarily makes: A. 800-1200 strokes/min B. 1600-2000 strokes/min C. 2400-2800 strokes/min D. 3200-3600 strokes/min

Last Answer : A. 800-1200 strokes/min

knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Description : knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height

Last Answer : a)Increase the co-efficient of friction between crop stalk machine

o over come the rear ward deflection the load given to outer end of the cutter bar is about..... (a)1.57cm/m (b) 2.0cm/m (b)3.0cm/m (d) 3.5cm/m

Description : o over come the rear ward deflection the load given to outer end of the cutter bar is about..... (a)1.57cm/m (b) 2.0cm/m (b)3.0cm/m (d) 3.5cm/m

Last Answer : b) 2.0cm/m

enght of cutter bar for the tractor operated mower or vertical conveyor reaper is..... (a) 1.5-3.0m (b) 3.0-4.5m (c)4.5-5.5m (d) >5.5m

Description : enght of cutter bar for the tractor operated mower or vertical conveyor reaper is..... (a) 1.5-3.0m (b) 3.0-4.5m (c)4.5-5.5m (d) >5.5m

Last Answer : (a) 1.5-3.0m

Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm

Description : Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm

Last Answer : a)400-550 rpm

Pick up reels are very effective in :- a) Cutting of upright crops b) Lifting of lodged (down) crops ahead of cutter bar C) Both (a) and (b) are true d) None of the above

Description : Pick up reels are very effective in :- a) Cutting of upright crops b) Lifting of lodged (down) crops ahead of cutter bar C) Both (a) and (b) are true d) None of the above

Last Answer : C) Both (a) and (b) are true

Speed of the cutter bar in case of combine (grain) is :- a) 400 – 550 rpm b) 500 – 800 rpm C) 800 - 1000 rpm d) 1000 – 1200 rpm

Description : Speed of the cutter bar in case of combine (grain) is :- a) 400 – 550 rpm b) 500 – 800 rpm C) 800 - 1000 rpm d) 1000 – 1200 rpm

Last Answer : a) 400 – 550 rpm

In your opinion, which is better, Pitman or Gregg shorthand?

Description : In your opinion, which is better, Pitman or Gregg shorthand?

Last Answer : I personally prefer Gregg, but this purely for aesthetic purposes.

What kind of shoe is Selena Gomez wearing in Another Cinderella Story?

Description : What kind of shoe is Selena Gomez wearing in Another Cinderella Story?

Last Answer : short boots

In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right compensation, the trajectory of the cutter will be a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5) b.(0,-5), (55,-5), (55, 35), (-5, 35), (-5,-5) c.(5, 5), (5, 25), (45, 25), (45, 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)

Description : In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right ... , 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)

Last Answer : a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5)

The distance of a given tool tip from the surface of workpiece is known as….. a.Tool length b.Tool length offset H c.Cutter radius d.Compensation

Description : The distance of a given tool tip from the surface of workpiece is known as….. a.Tool length b.Tool length offset H c.Cutter radius d.Compensation

Last Answer : b.Tool length offset H

How much of lead degree is given if the cutter is set at 88 degree? a) 2-degree b) 4 degree c) 3-degree d) 5 degree

Description : How much of lead degree is given if the cutter is set at 88 degree? a) 2-degree b) 4 degree c) 3-degree d) 5 degree

Last Answer : 2-degree

Is Crest White good for soothing gums that are irritated from wearing partial plates?

Description : Is Crest White good for soothing gums that are irritated from wearing partial plates?

Last Answer : Crest White is good for soothing gums, but only in moderation.

Is the USMC KA-BAR a good knife?

Description : Is the USMC KA-BAR a good knife?

Last Answer : Sure. It's a good knife, tough and durable for doing a lot of different jobs. There are a lot of good knives for that sort of work. Something like this might have more general ... when skinning game, a serrated section that is good for sawing through rope, and a comfortable lightweight handle.

One of the following is not the element of energy monitoring & targeting system a) Recording the energy consumption b) comparing the energy consumption C)Controlling the energy consumption d) Reducing the production

Description : One of the following is not the element of energy monitoring & targeting system a) Recording the energy consumption b) comparing the energy consumption C)Controlling the energy consumption d) Reducing the production

Last Answer :  Reducing the production

68. One of the following is not the element of energy monitoring & targeting system a) Recording the energy consumption b) Comparing the energy consumption c) Controlling the energy consumption d) Reducing the production

Description : 68. One of the following is not the element of energy monitoring & targeting system a) Recording the energy consumption b) Comparing the energy consumption c) Controlling the energy consumption d) Reducing the production

Last Answer : Reducing the production

Comparing energy consumption to the set target on a regular basis is called as _____. a]Reporting c] Determining b] Recording d] monitoring

Description : Comparing energy consumption to the set target on a regular basis is called as _____. a]Reporting c] Determining b] Recording d] monitoring

Last Answer : monitoring

___ energy consumption to an appropriate standard or benchmark. a] Setting target c] Comparing. b] Reporting d] Allocating

Description : ____ energy consumption to an appropriate standard or benchmark. a] Setting target c] Comparing. b] Reporting d] Allocating

Last Answer : comparing

An electrostatic voltmeter in which an assembly of figure-8-shaped metal plates rotates between the plates of a stationary assembly when a voltage is applied betweeen the assemblies.

Description : An electrostatic voltmeter in which an assembly of figure-8-shaped metal plates rotates between the plates of a stationary assembly when a voltage is applied betweeen the assemblies.

Last Answer : Kelvin voltmeter

It is the link between the knife and crank wheel of the mower. a. connecting rod c. rod d. None of above

Description : It is the link between the knife and crank wheel of the mower. a. connecting rod c. rod d. None of above

Last Answer : Ans-                                     b. Pitman

is also called as knife harrow. a. Spring tooth harrow c. Fixed tooth harrow d. None of the above

Description : is also called as knife harrow. a. Spring tooth harrow c. Fixed tooth harrow d. None of the above

Last Answer : Ans - b.Acme tooth harrow

is not well register, there is unbalance load, uneven harvesting and exclusive clogging of crops on the knife A) Vertical conveyor reaper B) MOVER C) Reaper binder D) Potato digger elevator.

Description : is not well register, there is unbalance load, uneven harvesting and exclusive clogging of crops on the knife A) Vertical conveyor reaper B) MOVER C) Reaper binder D) Potato digger elevator.

Last Answer : MOVER

How many plates can you fit on a Cap Barbell Olympic 6 ft Weight Bar?

Description : How many plates can you fit on a Cap Barbell Olympic 6 ft Weight Bar?

Last Answer : They will take 5 full size plates on each size and safely hold it.

In olden days the type of section adopted in trunk and out fall sewers was A. Parabolic shaped B. Horse shoe shaped C. Egg shaped D. Circular shaped

Description : In olden days the type of section adopted in trunk and out fall sewers was A. Parabolic shaped B. Horse shoe shaped C. Egg shaped D. Circular shaped

Last Answer : ANS: B

The suitable cross-section of sewers to carry combined flow, is A. Circular B. Egg shaped C. Rectangular D. Horse shoe shaped

Description : The suitable cross-section of sewers to carry combined flow, is A. Circular B. Egg shaped C. Rectangular D. Horse shoe shaped

Last Answer : ANS: B