A mower knife is said to be in proper registration when the knife section stops in the ……………..of its guard ( fingers ) on every stroke a. offset c. inclined d. None of above

A mower knife is said to be in proper registration when the knife section stops in the ……………..of its guard ( fingers ) on every stroke a. offset c. inclined d. None of above
by

1 Answer

Answer :

<!-- [if !supportLists] -->a.  <!-- [endif] -->Ans-                     b. centre

 


by

Related questions

Registration of a cutter bar means a) Centre of knife must stop in the centre of guard on each stroke b) Centre of knife should be ahead of guard c) Centre of knife should be behind the guard d) Centre of knife should be at the end of the guard

Description : Registration of a cutter bar means a) Centre of knife must stop in the centre of guard on each stroke b) Centre of knife should be ahead of guard c) Centre of knife should be behind the guard d) Centre of knife should be at the end of the guard

Last Answer : ans a

It is a mower with a knife made of several serrated triangular sections that reciprocate against stationary fingers. a. Rotary mower c. Cylinder mower. d. None of above

Description : It is a mower with a knife made of several serrated triangular sections that reciprocate against stationary fingers. a. Rotary mower c. Cylinder mower. d. None of above

Last Answer : Ans-   b. Reciprocating mower  

Registration of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. a

Description : Registration of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. a

Last Answer : ans a

is an assembly comparing of fingers, knife guides on wearing plates and shoe. a) Cutter bar b) Knife section c) Pitman d) Shoe

Description : is an assembly comparing of fingers, knife guides on wearing plates and shoe. a) Cutter bar b) Knife section c) Pitman d) Shoe

Last Answer : Cutter bar

Cylinder mower has rotating blades arranged in cylindrical form. a. Straight c. inclined. d. None of above

Description : Cylinder mower has rotating blades arranged in cylindrical form. a. Straight c. inclined. d. None of above

Last Answer : Ans-                     b. helical  

It is the link between the knife and crank wheel of the mower. a. connecting rod c. rod d. None of above

Description : It is the link between the knife and crank wheel of the mower. a. connecting rod c. rod d. None of above

Last Answer : Ans-                                     b. Pitman

Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b

Description : Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b

Last Answer : ans b

The implement which can work in offset position a)offset disc harrow b) mower c) both (a) and (b) d) none of the above

Description : The implement which can work in offset position a)offset disc harrow b) mower c) both (a) and (b) d) none of the above

Last Answer : c) both (a) and (b)

………………… documents are not accepted as per general guideline of company registration. A. without proper filling and loosing C. folded or improper B. Both A and B D. None of above

Description : ………………… documents are not accepted as per general guideline of company registration. A. without proper filling and loosing C. folded or improper B. Both A and B D. None of above

Last Answer : without proper filling and loosing

267 .Double knives movers offers advantage over conventional mower are a)Double knife are dynamically balanced b) They can be operated at higher forward speeds then conventional mower c)They produce more uniform stubble height d)All of the above

Description : 267 .Double knives movers offers advantage over conventional mower are a)Double knife are dynamically balanced b) They can be operated at higher forward speeds then conventional mower c)They produce more uniform stubble height d)All of the above

Last Answer : d)All of the above

are the labelling of cutter bar. a) Shoe, ledger plate, wearing plate, knife, knife section, etc. b) Star wheel, engine, cage wheel, etc. c) both A & B d) Conveyor belt, cutter bar, rivers, etc

Description : are the labelling of cutter bar. a) Shoe, ledger plate, wearing plate, knife, knife section, etc. b) Star wheel, engine, cage wheel, etc. c) both A & B d) Conveyor belt, cutter bar, rivers, etc

Last Answer : Shoe, ledger plate, wearing plate, knife, knife section, etc.

The purpose of registration in a mower is (A) to get uniform length of cut of grass (B)to run the mower at minimum power (C)to run the mower at uniform torque (D)to reduce the occurrence of overload

Description : The purpose of registration in a mower is (A) to get uniform length of cut of grass (B)to run the mower at minimum power (C)to run the mower at uniform torque (D)to reduce the occurrence of overload

Last Answer : (B)to run the mower at minimum power

My fingers feel prickly (uncomfortable) when I lightly stroke things (people, animals); could this be static?

Description : My fingers feel prickly (uncomfortable) when I lightly stroke things (people, animals); could this be static?

Last Answer : Probably static, especially this time of year. My cats are little electrified balls of fur right now.

in four stroke engine there is one power stroke for every revolutions' of the cranks shaft a. 1 b. 2 c. 3 d.4

Description : in four stroke engine there is one power stroke for every revolutions' of the cranks shaft a. 1 b. 2 c. 3 d.4

Last Answer : ans b

The distance of a given tool tip from the surface of workpiece is known as….. a.Tool length b.Tool length offset H c.Cutter radius d.Compensation

Description : The distance of a given tool tip from the surface of workpiece is known as….. a.Tool length b.Tool length offset H c.Cutter radius d.Compensation

Last Answer : b.Tool length offset H

Identify the following figure- a. Offset disc harrow. c. Single action disc harrow b. Double action disc harrow d. Tandem disc harrow

Description : Identify the following figure- a. Offset disc harrow. c. Single action disc harrow b. Double action disc harrow d. Tandem disc harrow

Last Answer : Single action disc harrow

It is a machine to separate grains from the harvested crop and provide clean grain without much loss and damage. a. Weeder c. mower d. None of above

Description : It is a machine to separate grains from the harvested crop and provide clean grain without much loss and damage. a. Weeder c. mower d. None of above

Last Answer : Ans-                              b. thresher  

Flail mower is a mower with high speed swinging knives, operating in a. horizontal plane c. Vertical plane d. None of above

Description : Flail mower is a mower with high speed swinging knives, operating in a. horizontal plane c. Vertical plane d. None of above

Last Answer : Ans-   b. either in the horizontal plane or in the vertical plane  

The conventional type of Mower consists of which of the following a) Wearing Plate b) Nozzle c) Air Chamber d) None of the above

Description : The conventional type of Mower consists of which of the following a) Wearing Plate b) Nozzle c) Air Chamber d) None of the above

Last Answer : Wearing Plate

is a common troubles in the operation of Mower. a) Knives get twisted. b) Knives get melted. c) Knives gets rusted. d) Knives gets break

Description : is a common troubles in the operation of Mower. a) Knives get twisted. b) Knives get melted. c) Knives gets rusted. d) Knives gets break

Last Answer : Knives gets break

is a machine to cut herbage crops and leave the them in swath. a) Wind rower b) Sickle mower c) Fail mower d) Gang mower

Description : is a machine to cut herbage crops and leave the them in swath. a) Wind rower b) Sickle mower c) Fail mower d) Gang mower

Last Answer : Sickle mower

What are the proper steps to take after being threatened at your place of employment with a pocket knife “jokingly” by a fellow employee?

Description : What are the proper steps to take after being threatened at your place of employment with a pocket knife “jokingly” by a fellow employee?

Last Answer : Talk to HR. Don't wait. Get it on file.

In second pass, assembler creates _ in binary format for every instruction in program and then refers to the symbol table to giving every symbol an_ _ relating the segment. a. Code and program b. Program and instruction c. Code and offset d. All of these

Description : In second pass, assembler creates _ in binary format for every instruction in program and then refers to the symbol table to giving every symbol an_ _ relating the segment. a. Code and program b. Program and instruction c. Code and offset d. All of these

Last Answer : c. Code and offset

An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is (A) Safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined members (D) Needs revision of the section

Description : An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is ( ... shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined members (D) Needs revision of the section

Last Answer : Answer: Option A

A particle moves along a rough plane inclined at 30? to the horizontal. The co-efficient of friction between the particle and the plane is 0.1. Its initial velocity is 15 m/sec. The ratio of the velocity of the particle when it move down the plane to that when it move up the plane would be in the regions a.8 ? 10 b.5 ? 7 c.2 ? 3 d.4 ? 6 e.10 ? 13

Description : A particle moves along a rough plane inclined at 30? to the horizontal. The co-efficient of friction between the particle and the plane is 0.1. Its initial velocity is 15 m/sec. The ratio of the velocity of the particle when it move ... be in the regions a.8 ? 10 b.5 ? 7 c.2 ? 3 d.4 ? 6 e.10 ? 13

Last Answer : b. 5 ? 7

Am I responsible for the dentist bill if my son accidentally causes an injury to his friend's tooth while playing with an air soft gun? The other boy had permission to play and did not have a the proper mouth guard.

Description : Am I responsible for the dentist bill if my son accidentally causes an injury to his friend's tooth while playing with an air soft gun? The other boy had permission to play and did not have a the proper mouth guard.

Last Answer : I think it might depend on 1. whose supervision they were under 2. if the boy was told to wear a mouth guard 3. the parent/guardian of that child new that their child was not equipped with the proper protection and still allowed it.

A grinding wheel rotates at 3000 rpm. When power supply is cut off the wheel stops in 5 sec. The number of revolutions made by the wheel before coming to rest would be a.500 b.107 dynes c.250 d.3000 e.1000

Description : A grinding wheel rotates at 3000 rpm. When power supply is cut off the wheel stops in 5 sec. The number of revolutions made by the wheel before coming to rest would be a.500 b.107 dynes c.250 d.3000 e.1000

Last Answer : c. 250

A grinding wheel rotates at 3000 rpm. When power supply is cut-off the wheel stops in 10 seconds. The number of revolutions made by the wheel before coming to rest would be a.1500 b.3000 c.1000 d.250 e.500

Description : A grinding wheel rotates at 3000 rpm. When power supply is cut-off the wheel stops in 10 seconds. The number of revolutions made by the wheel before coming to rest would be a.1500 b.3000 c.1000 d.250 e.500

Last Answer : d. 250

An automobile is travelling at 25 m/s. It takes 0.3 second to apply the brakes after which the deceleration is 6 m/s2. How far, in meters, does the automobile travel before it stops? a.45 b.107 dynes c.40 d.50 e.60

Description : An automobile is travelling at 25 m/s. It takes 0.3 second to apply the brakes after which the deceleration is 6 m/s2. How far, in meters, does the automobile travel before it stops? a.45 b.107 dynes c.40 d.50 e.60

Last Answer : e. 60

A grinding wheel is rotating at 3000 rpm. When the switch is turned off the wheel stops in 10 seconds. The uniform deceleration of the wheel was a.1 rad/s2 b.31.4 rad/s2 c.4 rad/s2 d.62.8 rad/s2 e.10.4 rad/s2

Description : A grinding wheel is rotating at 3000 rpm. When the switch is turned off the wheel stops in 10 seconds. The uniform deceleration of the wheel was a.1 rad/s2 b.31.4 rad/s2 c.4 rad/s2 d.62.8 rad/s2 e.10.4 rad/s2

Last Answer : b. 31.4 rad/s2

The limiting force of fiction is a.The friction force acting on a body when it is in motion b.The value of friction force which stops the movement of the body c.The value of friction force which cannot exceed under a situation d.The friction force acting when the body is just about to move e.Double of the normal friction

Description : The limiting force of fiction is a.The friction force acting on a body when it is in motion b.The value of friction force which stops the movement of the body c.The value of friction force which ... d.The friction force acting when the body is just about to move e.Double of the normal friction

Last Answer : d. The friction force acting when the body is just about to move

________ will provide indications of effectiveness of your operations. a) Benchmarking b) Stops c) Production d) machines

Description : ________ will provide indications of effectiveness of your operations. a) Benchmarking b) Stops c) Production d) machines

Last Answer : Benchmarking

A temperature scale whose zero point is absolute zero, the temperature of “0” entropy at which all molecular motion stops.  a. Celsius  b. Fahrenheit  c. Kelvin  d. Rankine

Description : A temperature scale whose zero point is absolute zero, the temperature of “0” entropy at which all molecular motion stops.  a. Celsius  b. Fahrenheit  c. Kelvin  d. Rankine

Last Answer : Kelvin

An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Description : An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Last Answer : Answer: Option D

A beam is said to be of uniform strength, if (A) B.M. is same throughout the beam (B) Shear stress is same throughout the beam (C) Deflection is same throughout the beam (D) Bending stress is same at every section along its longitudinal axis

Description : A beam is said to be of uniform strength, if (A) B.M. is same throughout the beam (B) Shear stress is same throughout the beam (C) Deflection is same throughout the beam (D) Bending stress is same at every section along its longitudinal axis

Last Answer : (D) Bending stress is same at every section along its longitudinal axis

The truss element can deform only in the a.vertical direction b.horizontal direction c.inclined direction d.axial direction

Description : The truss element can deform only in the a.vertical direction b.horizontal direction c.inclined direction d.axial direction

Last Answer : d.axial direction

An electric motor drives a windless which hauls up a crate A of weight W = 500 kg up an inclined plane through a height of 10 m in 2 minutes. The torque acting on the windless is 25 kgm and the drum of the windless makes 30 rpm. The efficiency of the inclined plane would be a.0.41 b.0.61 c.0.265 d.0.5305 e.0.66

Description : An electric motor drives a windless which hauls up a crate A of weight W = 500 kg up an inclined plane through a height of 10 m in 2 minutes. The torque acting on the windless is 25 kgm and the drum of the ... The efficiency of the inclined plane would be a.0.41 b.0.61 c.0.265 d.0.5305 e.0.66

Last Answer : d. 0.5305

A block A is dropped down a smooth inclined plane, while another identical block B is released for free fall from the same height a.block A will have higher velocity than block B while hitting the ground b.block B will hit the ground earlier. c.both will hit the ground simultaneously d.block A will hit the ground earlier e.107 dynes

Description : A block A is dropped down a smooth inclined plane, while another identical block B is released for free fall from the same height a.block A will have higher velocity than block B while hitting the ... . c.both will hit the ground simultaneously d.block A will hit the ground earlier e.107 dynes

Last Answer : b. block B will hit the ground earlier.

The angle of friction is a.The angle which frictional force makes with the normal b.The anle at which the force applied from external souce will cause movement c.The angle at which fictional force is inclined to external force d.The angle between the normal reaction and the resultant of normal reaction and the limiting friction e.None of the above

Description : The angle of friction is a.The angle which frictional force makes with the normal b.The anle at which the force applied from external souce will cause movement c.The angle at which fictional ... the normal reaction and the resultant of normal reaction and the limiting friction e.None of the above

Last Answer : d. The angle between the normal reaction and the resultant of normal reaction and the limiting friction

The work done in sliding a block of weight of 50 kg up a plane inclined at an angle of 30? to the horizontal so that the block is lifted through 1 m ( a.More than 50 kgm b.50 kgm c.Less than 5 kgm d.15 kgm only e.None of the above

Description : The work done in sliding a block of weight of 50 kg up a plane inclined at an angle of 30? to the horizontal so that the block is lifted through 1 m ( a.More than 50 kgm b.50 kgm c.Less than 5 kgm d.15 kgm only e.None of the above

Last Answer : a. More than 50 kgm

A block of weight 20 kg slides with an initial velocity of 2 m sec down an inclined plane on to a spring of stiffness 10 kg/cm. If the co--efficient of friction is 0.2, angle ? = 30 the ratio of maximum compession of spring, neglecting friction to that while considering friction would be a.More than one b.One c.Less than one d.Depends on the stiffness of spring e.None of the above

Description : A block of weight 20 kg slides with an initial velocity of 2 m sec down an inclined plane on to a spring of stiffness 10 kg/cm. If the co--efficient of friction is 0.2, angle ? = 30 the ratio of ... be a.More than one b.One c.Less than one d.Depends on the stiffness of spring e.None of the above

Last Answer : a. More than one

The principle of conservation of energy cannot be applied in case of a.Flow of heat through a metal b.Ideal flow of water in a pipe c.Simple pendulum d.Sliding of a particle along inclined plane with friction e.A particle moving in gravitational field

Description : The principle of conservation of energy cannot be applied in case of a.Flow of heat through a metal b.Ideal flow of water in a pipe c.Simple pendulum d.Sliding of a particle along inclined plane with friction e.A particle moving in gravitational field

Last Answer : e. A particle moving in gravitational field

The direction of projection for the range of a projectile to be maximum on an inclined plane having angle of inclination 30? to the horizontal, whould be a.45? with horizontal b.30? with vertical c.30? with horizontal d.60? with inclined plane e.45? with inclined plane

Description : The direction of projection for the range of a projectile to be maximum on an inclined plane having angle of inclination 30? to the horizontal, whould be a.45? with horizontal b.30? with vertical c.30? with horizontal d.60? with inclined plane e.45? with inclined plane

Last Answer : b. 30? with vertical

The angle which an inclined surface makes with the horizontal when a body placed on it is on the point moving down is known as a.Angle of friction b.Angle of limiting friction c.Angle of inclination d.Angle of repose e.None of the above

Description : The angle which an inclined surface makes with the horizontal when a body placed on it is on the point moving down is known as a.Angle of friction b.Angle of limiting friction c.Angle of inclination d.Angle of repose e.None of the above

Last Answer : d. Angle of repose

A boy sitting in a rail road car throws a ball straight up into the air. The ball will fall back into his hands when the rail road car is a.moving at constant velocity b.accelerating forward while going around a curve of radius equal to the maximum height attained by the ball c.107 dynes d.accelerating forwardA block A is dropped down a smooth inclined plane, while another identical block B is released for free fall from the same height e.decelerating

Description : A boy sitting in a rail road car throws a ball straight up into the air. The ball will fall back into his hands when the rail road car is a.moving at constant velocity b.accelerating ... inclined plane, while another identical block B is released for free fall from the same height e.decelerating

Last Answer : a. moving at constant velocity

When two forces acting at a point are such that if the direction of one is reversed, the direction of the resultant is turned through a right angle, the forces must be a.inclined at more than 90? b.inclined at less than 90? c.equal in magnitude d.acting at 180? e.107 dynes

Description : When two forces acting at a point are such that if the direction of one is reversed, the direction of the resultant is turned through a right angle, the forces must be a.inclined at more than 90? b.inclined at less than 90? c.equal in magnitude d.acting at 180? e.107 dynes

Last Answer : c. equal in magnitude

A body of weight W is resting at a plane inclined at 30? to the horizontal. It is attached to a string making an angle of 60? with horizontal. If the angle of friction be 30? the tension in the string would be a.Zero b.W c.W/2 d.2W e.None of the above

Description : A body of weight W is resting at a plane inclined at 30? to the horizontal. It is attached to a string making an angle of 60? with horizontal. If the angle of friction be 30? the tension in the string would be a.Zero b.W c.W/2 d.2W e.None of the above

Last Answer : c. W/2

A block slides down a smooth inclined plane when released from the top while another falls freely from the same point. The value of which parameter in the two cases will be identical? a.Time taken to reach the ground b.Kinetic energy at the ground c.Momentum at the ground d.Velocity while touching the ground e.Kinetic energy after one second

Description : A block slides down a smooth inclined plane when released from the top while another falls freely from the same point. The value of which parameter in the two cases will be identical? a.Time ... ground c.Momentum at the ground d.Velocity while touching the ground e.Kinetic energy after one second

Last Answer : d. Velocity while touching the ground

In which case power required would be more a.In lifting up a weight of 100 kg at a velocity of 3 m/sec but accelerating upwards at 0.5 m/sec b.In lowering a weight of 100 kg along an a inclined plane at an angle of 45? with c.In lifting up a weight of 100 kg at a constant speed of 3 m/sec d.In lowering the weight at a constant speed of 3 m/sec e.In lowering the weight at a velocity of 3 m/sec and acceleration of 1 m/sec2

Description : In which case power required would be more a.In lifting up a weight of 100 kg at a velocity of 3 m/sec but accelerating upwards at 0.5 m/sec b.In lowering a weight of 100 kg along an a inclined plane ... speed of 3 m/sec e.In lowering the weight at a velocity of 3 m/sec and acceleration of 1 m/sec2

Last Answer : a. In lifting up a weight of 100 kg at a velocity of 3 m/sec but accelerating upwards at 0.5 m/sec