Description : If the tendon is placed at an eccentricity e below the centroidal axis of the longitudinal axis of a rectangular beam (sectional modulus Z and stressed load P in tendon) the stress at the extreme top edge (A) Is ... by PZ/e (B) Is increased by Pe/Z (C) Is decreased by Pe/Z (D) Remains unchanged
Last Answer : Answer: Option C
Description : If the width of the foundation for two equal columns is restricted, the shape of the footing generally adopted, is (A) Square (B) Rectangular (C) Trapezoidal (D) Triangular
Last Answer : Answer: Option B
Description : To have pressure wholly compressive under the base of a retaining wall of width b, the resultant of the weight of the wall and the pressure exerted by the retained, earth should have eccentricity not more than (A) b/3 (B) b/4 (C) b/5 (D) b/6
Last Answer : Answer: Option D
Description : A cantilever beam rectangular in cross-section is subjected to an isolated load at its free end. If the width of the beam is doubled, the deflection of the free end will be changed in the ratio of (A) 8 (B) 1/8 (C) 1/2 (D) 3
Last Answer : (C) 1/2
Description : The eccentricity (e) of a hollow circular column, external diameter 25 cm, internal diameter 15 cm for an eccentric load 100 t for non-development of tension, is (A) 2.75 cm (B) 3.00 cm (C) 3.50 cm (D) 4.25 cm
Last Answer : (D) 4.25 cm
Description : The greatest eccentricity which a load W can have without producing tension on the cross-section of a short column of external diameter D and internal diameter d, is (A) 4W/ (D² - d²) (B) (D² - d²)/32D (C) (D² + d²)/8D (D) (D² - d²)/8D
Last Answer : (C) (D² + d²)/8D
Description : The range of spread from the wall base to outer edge of a brick work foundation does not exceed (A) 1/2 horizontal to 1 vertical (B) 2/3 horizontal to 1 vertical (C) 1 horizontal to 1 vertical (D) 2 horizontals to 1 vertical
Description : The moment of inertia of a rectangular section of width and depth about an axis passing through C.G. and parallel to its width is (A) BD²/6 (B) BD3 /6 (C) BD3 /12 (D) B²D/6
Last Answer : (C) BD3 /12
Description : A rectangular bar of width b and height h is being used as a cantilever. The loading is in a plane parallel to the side b. The section modulus is (A) bh3 /12 (B) bh²/6 (C) b²h/6 (D) None of these
Last Answer : (C) b²h/6
Description : A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data
Last Answer : b. 5208 Mpa
Description : For a ribbed slab (A) Clear spacing between ribs shall not be greater than 4.5 cm (B) Width of the rib shall not be less than 7.5 cm (C) Overall depth of the slab shall not exceed four times the breadth of the rib (D) All the above
Description : Pick up the incorrect statement from the following: (A) Space between the exterior walls of a warehouse and bag piles should be 30 cm (B) Cement bags should preferably be piled on wooden planks (C) Width and height of the pile should not exceed 3 m and 2.70 m respectively (D) None of these
Description : The width of the hollow space between two walls of a cavity wall should not exceed (A) 5 cm (B) 7.5 cm (C) 10 cm (D) 15 cm
Description : In “Severe exposure” the allowable crack width at the surface of concrete should not exceed [ A ] 0.1 mm [ B ] 0.2 mm [ C ] 0.3 mm [ D ] 0.4 mm
Last Answer : [ A ] 0.1 mm
Description : Pick up the correct statement from the following: (A) If the ratio of depth to width is less than 2, it is shallow foundation (B) If the ratio of depth to width is more than 2, it is deep ... the ratio of the length to width is between 1 and 2, it is spread foundation (D) All the above
Description : A foundation is called shallow if its depth, is (A) One-fourth of its width (B) Half of its width (C) Three-fourth of its width (D) Equal to its width
Description : For a strongest rectangular beam cut from a circular log, the ratio of the width and depth, is (A) 0.303 (B) 0.404 (C) 0.505 (D) 0.707
Last Answer : (D) 0.707
Description : The section modulus of a rectangular section is proportional to (A) Area of the section (B) Square of the area of the section (C) Product of the area and depth (D) Product of the area and width
Last Answer : (A) Area of the section
Description : For the same height, the bottom width for no tension, (A) For triangular section is more than rectangular section (B) For rectangular section is more than triangular section (C) For triangular section is same as that of a rectangular section (D) None of these
Last Answer : (C) For triangular section is same as that of a rectangular section
Description : The deflection of any rectangular beam simply supported, is (A) Directly proportional to its weight (B) Inversely proportional to its width (C) Inversely proportional to the cube of its depth (D) Directly proportional to the cube of its length
Last Answer : (C) Inversely proportional to the cube of its depth
Description : A T-beam behaves as a rectangular beam of a width equal to its flange if its neutral axis (A) Remains within the flange (B) Remains below the slab (C) Coincides the geometrical centre of the beam (D) None of these
Last Answer : Answer: Option A
Description : The discharge over a rectangular notch is (where b = Width of notch, and H = Height of liquid, above the sill of the notch) (A) (2/3) Cd × b × gH) (B) (2/3) Cd × b × g) × H (C) (2/3) Cd × b × g) × H 3/2 (D) (2/3) Cd × b × g) × H
Description : For hydraulically efficient rectangular channel of bed width 4.0 m, the depth of flow is (a) 4 m (b) 0.5 m (c) 1 m (d) 2 m
Last Answer : (d) 2 m
Description : The maximum permissible eccentricity for no tension at the base of a gravity dam is (A) B/2 (B) B/3 (C) B/4 (D) B/6
Description : If metres is the distance between extreme axles of a vehicle, its gross load should not exceed (A) 1525 (L + 4.3) - 14.7 L2 (B) 1526 (L + 5.3) - 14.7 L2 (C) 1525 (L + 6.3) - 14.7 L2 (D) 1525 (L + 7.3) - 14.7 L2
Description : Consider the following statements: Maximum slenderness ratio of load-bearing masonry walls for a dwelling having more than two storeys shall not exceed. 1. 12, if lime mortar is used 2. 18, if cement-lime mortar 1:2:9 is used 3. 24, ... ? (a) 1 and 2 only b) 2 and 3 only c) 1 and 3 only d)1, 2 and 3
Last Answer : b) 2 and 3 only
Description : What is the distance away from midspan of a plastic hinge if developing in a simply supported beam of rectangular cross-section and span 6 m, subjected to a point load at the centre? (a) Zero (b) 1 m (c) 2 m (d) 3 m
Last Answer : (a) Zero
Description : The dimensions of a rectangular settling tank are: length 24 m, width 6 m and depth 3 m. If 2 hour detention period for tanks is recommended, the rate of flow of sewage per hour, is A. 204 cu.m B. 208 cu.m C. 212 cu.m D. 216 cu.m
Last Answer : ANS: D
Description : Which one of the following statements is correct? (A) When the axes of rotation of the graduated circle and the verniers are not coincident, the instrument possesses eccentricity (B) The mean of the ... Vernier may be used if the readings of two verniers differ by a constant (D) All the above
Last Answer : (D) All the above
Description : To ascertain the maximum permissible eccentricity of loads on circular columns, the rule generally followed, is (A) Middle half rule of columns (B) Middle third rule of columns (C) Middle fourth rule of columns (D) None of these
Last Answer : (C) Middle fourth rule of columns
Description : A column said to be under uniaxial bending, when the eccentricity is [ A ] with respect to one axis only [ B ] with respect to two axes [ C ] zero [ D ] 20 mm
Last Answer : [ A ] with respect to one axis only
Description : According to IS:456-2000, the minimum eccentricity in no case [ A ] Shall be not less than 20mm [ B ] Shall be not greater than 30mm [ C ] Shall be 20mm-30mm [ D ] None of the above
Last Answer : [ A ] Shall be not less than 20mm
Description : A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is: (A) 4.0 mm (B) 4.5 mm (C) 5.0 mm (D) 5.5 mm
Last Answer : (C) 5.0 mm
Description : A short column 20 cm 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on ... should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these
Description : In testing a pile by load test, pile platform is loaded with one and half times the design load and a maximum settlement is noted. The load is gradually removed and the consequent rebound is measured. For a safe pile, the net ... load should not exceed (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm
Description : Maximum slenderness ratio for load-bearing masonry wall in cement mortar, as per IS code, shall not exceed. (a) 13 (b) 20 (c) 27 (d) 30
Last Answer : (c) 27
Description : Which of the following conditions of loading imposes the greatest load on the foundation in case of dry docks? (A) When the dock is empty (B) When the dock is empty with the ship of maximum tonnage (C) When the dock is full of water (D) When the dock is dry and is under construction
Last Answer : (C) When the dock is full of water
Description : Pick up the incorrect statement from the following: (A) The function of foundation is to distribute the load of super structure over a large bearing area (B) No timbering is required for shallow ... can be constructed on made-up soil (D) Black cotton soil is very good for foundation bed
Description : Consider the following statements: 1. The benefit of surcharge and depth of foundation is only marginal in case of footings on purely cohesive soils. 2. The bearing capacity of a footing in pure clay increases with increase in size of the ... , 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only
Last Answer : (d) 1 & 3 only
Description : In case of a simply supported rectangular beam of span L and loaded with a central load W, the length of elasto-plastic zone of the plastic hinge, is (A) L/2 (B) L/3 (C) L/4 (D) L/5
Last Answer : (B) L/3
Description : The ratio of the length and depth of a simply supported rectangular beam which experiences maximum bending stress equal to tensile stress, due to same load at its mid span, is (A) 1/2 (B) 2/3 (C) 1/4 (D) 1/3
Last Answer : (B) 2/3
Description : A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated load W at its mid-span. The same bar experiences an extension e under same tensile load. The ratio of the maximum deflection to the ... (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²
Last Answer : (C) (L/2d)
Description : A rectangular log of wood is floating in water with a load of 100 N at its centre. The maximum shear force in the wooden log is (A) 50 N at each end (B) 50 N at the centre (C) 100 N at the centre (D) None of these
Last Answer : (C) 100 N at the centre
Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive
Last Answer : (C) 26.67 kg/cm2 tensile
Description : The range within which a load can be applied on a rectangular column, to avoid any tensile stress, is (A) One-half of the base (B) One-fifth of the base (C) One-fourth of the base (D) One-fifth of the base
Last Answer : (B) One-fifth of the base
Description : If a rectangular beam measuring 10 × 18 × 400 cm carries a uniformly distributed load such that the bending stress developed is 100 kg/cm2 . The intensity of the load per metre length, is (A) 240 kg (B) 250 kg (C) 260 kg (D) 270 kg
Last Answer : (B) 250 kg
Description : A 8 metre long simply supported rectangular beam which carries a distributed load 45 kg/m. experiences a maximum fibre stress 160 kg/cm2 . If the moment of inertia of the beam is 640 cm4 , the overall depth of the beam is (A) 10 cm (B) 12 cm (C) 15 cm (D) 18 cm
Last Answer : (A) 10 cm
Description : If a rectangular pre-stressed beam of an effective span of 5 meters and carrying a total load 3840 kg/m, is designed by the load balancing method, the central dip of the parabolic tendon should be (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm
Description : The length of a rectangular piece of fabric is twice its width . identify the geometrical representation of this situation when represented as an equation in two variables. Width and length be represented as x and y respectively . -Maths 9th
Last Answer : answer:
Description : what- sam has 15 identical rectangular windows in his home. The length of each window is twice the width, and the area of each window is 8 square feet. Sam wants to ...?
Last Answer : 45