The range of spread from the wall base to outer edge of a brick work foundation does not exceed (A) 1/2 horizontal to 1 vertical (B) 2/3 horizontal to 1 vertical (C) 1 horizontal to 1 vertical (D) 2 horizontals to 1 vertical

The range of spread from the wall base to outer edge of a brick work foundation does not exceed
(A) 1/2 horizontal to 1 vertical
(B) 2/3 horizontal to 1 vertical
(C) 1 horizontal to 1 vertical
(D) 2 horizontals to 1 vertical
by

1 Answer

Answer :

Answer: Option C
by

Related questions

A retaining wall 6m high supports a backfill with a surcharge angle of 10°. The back of the wall is inclined to the vertical at a positive batter angle of 5°. If the angle of wall friction is 7°, then the resultant active earth pressure will act at a distance of 2 m above the base and inclined to the horizontal at an angle of (A) 7° (B) 10° (C) 12° (D) 17

Description : A retaining wall 6m high supports a backfill with a surcharge angle of 10°. The back of the wall is inclined to the vertical at a positive batter angle of 5°. If the angle of wall friction is 7°, then the resultant ... inclined to the horizontal at an angle of (A) 7° (B) 10° (C) 12° (D) 17

Last Answer : (C) 12°

Before providing super-elevation on roads, the portion of the carriageway between the crown and the outer edge is made (A) To have a reduced fall (B) Horizontal (C) To have slope of the camber on the other half of the carriageway (D) None of these

Description : Before providing super-elevation on roads, the portion of the carriageway between the crown and the outer edge is made (A) To have a reduced fall (B) Horizontal (C) To have slope of the camber on the other half of the carriageway (D) None of these

Last Answer : Answer: Option C

The term string is used for (A) The underside of a stair (B) Outer projecting edge of a tread (C) A sloping member which supports the steps in a stair (D) A vertical member between two treads

Description : The term string is used for (A) The underside of a stair (B) Outer projecting edge of a tread (C) A sloping member which supports the steps in a stair (D) A vertical member between two treads

Last Answer : Answer: Option C

The method of moving each brick through a small horizontal distance before it is finally laid in any brick wall and pressing it by means of brick hammer, is known as (A) Trowelling (B) Laying (C) Grouting (D) Placing

Description : The method of moving each brick through a small horizontal distance before it is finally laid in any brick wall and pressing it by means of brick hammer, is known as (A) Trowelling (B) Laying (C) Grouting (D) Placing

Last Answer : Answer: Option B

The angle of repose of a soil is the maximum angle which the outer face of the soil mass makes (A) With the horizontal (B) With the vertical (C) With the perpendicular to the inclined plane of the soil (D) None of these

Description : The angle of repose of a soil is the maximum angle which the outer face of the soil mass makes (A) With the horizontal (B) With the vertical (C) With the perpendicular to the inclined plane of the soil (D) None of these

Last Answer : Answer: Option A

The position of a brick when laid on its side 9 cm × 9 cm with its frog in the vertical plane, is called (A) Brick on edge (B) Brick on end (C) Brick on bed (D) Brick held vertically

Description : The position of a brick when laid on its side 9 cm × 9 cm with its frog in the vertical plane, is called (A) Brick on edge (B) Brick on end (C) Brick on bed (D) Brick held vertically

Last Answer : Option B

To stagger vertical joints in successive courses of a wall, a piece of brick is generally used at the end of the course, which is known as (A) Bat (B) Header (C) Stretcher (D) Closer

Description : To stagger vertical joints in successive courses of a wall, a piece of brick is generally used at the end of the course, which is known as (A) Bat (B) Header (C) Stretcher (D) Closer

Last Answer : Answer: Option D

Draw a neat labeled sectional view showing different components of building from foundation to parapet, for a load bearing brick masonry wall.

Description : Draw a neat labeled sectional view showing different components of building from foundation to parapet, for a load bearing brick masonry wall.

Last Answer : Draw a neat labeled sectional view showing different components of building from foundation to parapet, for a load bearing brick masonry wall.

The expected out turn of brick work in cement mortar in foundation and plinth per mason per day, is (A) 1.00 m3 (B) 1.25 m3 (C) 1.50 m3 (D) 1.75 m3

Description : The expected out turn of brick work in cement mortar in foundation and plinth per mason per day, is (A) 1.00 m3 (B) 1.25 m3 (C) 1.50 m3 (D) 1.75 m3

Last Answer : (B) 1.25 m3

The toe projection of foundation slabs is taken (A) As one third of the base (B) As one sixth of overall height of the wall (C) Equal to heel slab (D) Below ground surface

Description : The toe projection of foundation slabs is taken (A) As one third of the base (B) As one sixth of overall height of the wall (C) Equal to heel slab (D) Below ground surface

Last Answer : Answer: Option A

The weight of a good quality brick when immersed in water for a period of 16 hours should not exceed the weight of dry brick (A) 20 % (B) 15 % (C) 10 % (D) None of these

Description : The weight of a good quality brick when immersed in water for a period of 16 hours should not exceed the weight of dry brick (A) 20 % (B) 15 % (C) 10 % (D) None of these

Last Answer : Answer: Option A

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

A failure wedge develops if a retaining wall (A) Moves away from the backfill (B) Moves towards the backfill (C) Sinks downwards (D) Stresses equally by vertical and horizontal forces

Description : A failure wedge develops if a retaining wall (A) Moves away from the backfill (B) Moves towards the backfill (C) Sinks downwards (D) Stresses equally by vertical and horizontal forces

Last Answer : Answer: Option A

Rankine's theory of active earth pressure assumes (A) Soil mass is homogeneous, dry and cohesionless (B) Ground surface is a plane which may be horizontal or inclined (C) Back of the wall is vertical and smooth (D) All the above

Description : Rankine's theory of active earth pressure assumes (A) Soil mass is homogeneous, dry and cohesionless (B) Ground surface is a plane which may be horizontal or inclined (C) Back of the wall is vertical and smooth (D) All the above

Last Answer : Answer: Option D

A projectile is fired at an angle to the vertical. Its horizontal range will be maximum when is (A) 0° (B) 30° (C) 45° (D) 60°

Description : A projectile is fired at an angle to the vertical. Its horizontal range will be maximum when is (A) 0° (B) 30° (C) 45° (D) 60°

Last Answer : (C) 45°

For a rectangular foundation of width b, eccentricity of load should not exceed (A) b/2 (B) b/3 (C) b/4 (D) b/6

Description : For a rectangular foundation of width b, eccentricity of load should not exceed (A) b/2 (B) b/3 (C) b/4 (D) b/6

Last Answer : For a rectangular foundation of width b, eccentricity of load should not exceed (A) b/2 (B) b/3 (C) b/4 (D) b/6

To ensure uniform pressure distribution, the thickness of the foundation, isA) Kept uniform throughout (B) Increased gradually towards the edge (C) Decreased gradually towards the edge (D) Kept zero at the edge

Description : To ensure uniform pressure distribution, the thickness of the foundation, is A) Kept uniform throughout (B) Increased gradually towards the edge (C) Decreased gradually towards the edge (D) Kept zero at the edge

Last Answer : Answer: Option C

The term frog means (A) An apparatus to lift the stone (B) A depression on a face of brick (C) Vertical joint in a brick work (D) Soaking brick in water

Description : The term frog means (A) An apparatus to lift the stone (B) A depression on a face of brick (C) Vertical joint in a brick work (D) Soaking brick in water

Last Answer : Answer: Option B

Total pressure on the vertical face of a retaining wall of height h acts parallel to free surface and from the base at a distance of (A) h/4 (B) h/3 (C) h/2 (D) 2h/3

Description : Total pressure on the vertical face of a retaining wall of height h acts parallel to free surface and from the base at a distance of (A) h/4 (B) h/3 (C) h/2 (D) 2h/3

Last Answer : Answer: Option B

Pick up the incorrect statement from the following: (A) The width of the wall is constructed thicker at the base in a stepped fashion (B) A long vertical load transferring concrete structure is called a concrete pile (C) In pile which transfers the load to the soil by the friction between the pile and the surrounding soil is called friction pile (D) The pile which transfers the load to a hard rock bed at certain depth is called load bearing

Description : Pick up the incorrect statement from the following: (A) The width of the wall is constructed thicker at the base in a stepped fashion (B) A long vertical load transferring concrete structure is ... ) The pile which transfers the load to a hard rock bed at certain depth is called load bearing

Last Answer : Answer: Option D

Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of the column (C) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column

Description : Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of ... ) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column

Last Answer : Answer: Option C

Top bars are extended to the projecting parts of the combined footing of two columns Ldistance apart for a distance of (A) 0.1 L from the outer edge of column (B) 0.1 L from the centre edge of column (C) Half the distance of projection (D) One-fourth the distance of projection

Description : Top bars are extended to the projecting parts of the combined footing of two columns Ldistance apart for a distance of (A) 0.1 L from the outer edge of column (B) 0.1 L from the centre edge of column (C) Half the distance of projection (D) One-fourth the distance of projection

Last Answer : Answer: Option B

The increase in pressure at the outer edge of a drum of radius (r) completely filled up with liquid (A) 2 r2 (B) 2 2 r2 (C) 2 r2 /2 (D) 2 r2 /4

Description : The increase in pressure at the outer edge of a drum of radius (r) completely filled up with liquid (A) 2 r2 (B) 2 2 r2 (C) 2 r2 /2 (D) 2 r2 /4

Last Answer : Answer: Option C

no super elevation is provided on a road along curves, pot holes may develop at (A) Inner edge of the road (B) Outer edge of the road (C) Centre of the road (D) Nowhere on the road

Description : no super elevation is provided on a road along curves, pot holes may develop at (A) Inner edge of the road (B) Outer edge of the road (C) Centre of the road (D) Nowhere on the road

Last Answer : Answer: Option B

Raising of outer edge of a road with respect to inner edge, is known (A) Super elevation (B) Cant (C) Banking (D) All the above

Description : Raising of outer edge of a road with respect to inner edge, is known (A) Super elevation (B) Cant (C) Banking (D) All the above

Last Answer : Answer: Option D

If the width of carriage way is 12.5 metres, outer edge 50 cm higher than the inner edge, the required super elevation is (A) 50 cm (B) 1 in 25 (C) 1 in 400 (D) 1 in 40

Description : If the width of carriage way is 12.5 metres, outer edge 50 cm higher than the inner edge, the required super elevation is (A) 50 cm (B) 1 in 25 (C) 1 in 400 (D) 1 in 40

Last Answer : Answer: Option B

The most commonly adopted method to provide super-elevation on roads, is by pivoting the road surface about (A) Outer edge so that the inner edge is lowered (B) Crown so that outer edge is raised and inner edge is lowered (C) Inner edge so that outer edge is raised (D) None of these

Description : The most commonly adopted method to provide super-elevation on roads, is by pivoting the road surface about (A) Outer edge so that the inner edge is lowered (B) Crown so that outer edge is raised and inner edge is lowered (C) Inner edge so that outer edge is raised (D) None of these

Last Answer : Answer: Option C

Pick up the correct statement from the following: (A) If the ratio of depth to width is less than 2, it is shallow foundation (B) If the ratio of depth to width is more than 2, it is deep foundation (C) If the ratio of the length to width is between 1 and 2, it is spread foundation (D) All the above

Description : Pick up the correct statement from the following: (A) If the ratio of depth to width is less than 2, it is shallow foundation (B) If the ratio of depth to width is more than 2, it is deep ... the ratio of the length to width is between 1 and 2, it is spread foundation (D) All the above

Last Answer : Answer: Option D

A grillage foundation (A) Is provided for heavily loaded isolated columns (B) Is treated as spread foundation (C) Consists of two sets of perpendicularly placed steel beams (D) All the above

Description : A grillage foundation (A) Is provided for heavily loaded isolated columns (B) Is treated as spread foundation (C) Consists of two sets of perpendicularly placed steel beams (D) All the above

Last Answer : Answer: Option D

In slabs the Maximum horizontal distance between parallel main reinforcement should not exceed i.Three times effective depth ii Five times effective depth iii 300mm iv 450 mm [ A ] i and iii [ B ] i and iv [ C ] ii and iii [ D ] ii and iv

Description : In slabs the Maximum horizontal distance between parallel main reinforcement should not exceed i.Three times effective depth ii Five times effective depth iii 300mm iv 450 mm [ A ] i and iii [ B ] i and iv [ C ] ii and iii [ D ] ii and iv

Last Answer : [ A ] i and iii

The brick work is not measured in cu m in case of (A) One or more than one brick wall (B) Brick work in arches (C) Reinforced brick work (D) Half brick wall

Description : The brick work is not measured in cu m in case of (A) One or more than one brick wall (B) Brick work in arches (C) Reinforced brick work (D) Half brick wall

Last Answer : (D) Half brick wall

Consider the following activities in a building construction: 1. Concreting of roof slabs 2. Brick-jelly lime concrete terracing 3. Erection of form work for slab 4. Construction of parapet wall in terrace The correct sequence of these activities is (A) 1, 3, 2, 4 (B) 3, 1, 4, 2 (C) 3, 1, 2, 4 (D) 1, 3, 4, 2

Description : Consider the following activities in a building construction: 1. Concreting of roof slabs 2. Brick-jelly lime concrete terracing 3. Erection of form work for slab 4. Construction of parapet wall in terrace The correct sequence of these ... (B) 3, 1, 4, 2 (C) 3, 1, 2, 4 (D) 1, 3, 4, 2

Last Answer : (C) 3, 1, 2, 4

Brick nogging type of partition wall, is constructed by (A) Laying bricks as stretchers in cement mortar (B) Laying bricks as headers in cement mortar (C) Reinforcing brick wall with iron straps (D) Constructing brick work within a wooden framework

Description : Brick nogging type of partition wall, is constructed by (A) Laying bricks as stretchers in cement mortar (B) Laying bricks as headers in cement mortar (C) Reinforcing brick wall with iron straps (D) Constructing brick work within a wooden framework

Last Answer : Answer: Option D

To obtain good bonding in brick masonry (A) First class bricks are used (B) Vertical joints in alternate courses are kept in plumb line (C) Bats are used where necessary (D) All the above

Description : To obtain good bonding in brick masonry (A) First class bricks are used (B) Vertical joints in alternate courses are kept in plumb line (C) Bats are used where necessary (D) All the above

Last Answer : Option D

If vertical angles of inclined sights do not exceed 10° and non-verticality of the staff remains within 1°, stadia system of tacheometric observations are made on (A) Staff normal (B) Staff vertical (C) Staff normal as well as vertical (D) None of these

Description : If vertical angles of inclined sights do not exceed 10° and non-verticality of the staff remains within 1°, stadia system of tacheometric observations are made on (A) Staff normal (B) Staff vertical (C) Staff normal as well as vertical (D) None of these

Last Answer : (A) Staff normal

Seepage through foundation in an earthen dam is controlled by providing (A) Rock toe (B) Horizontal blanket (C) Impervious cut off (D) Chimney drain

Description : Seepage through foundation in an earthen dam is controlled by providing (A) Rock toe (B) Horizontal blanket (C) Impervious cut off (D) Chimney drain

Last Answer : Answer: Option C

The direction of projection for the range of a projectile to be maximum on an inclined plane having angle of inclination 30? to the horizontal, whould be a.45? with horizontal b.30? with vertical c.30? with horizontal d.60? with inclined plane e.45? with inclined plane

Description : The direction of projection for the range of a projectile to be maximum on an inclined plane having angle of inclination 30? to the horizontal, whould be a.45? with horizontal b.30? with vertical c.30? with horizontal d.60? with inclined plane e.45? with inclined plane

Last Answer : b. 30? with vertical

If the plane table is not horizontal in a direction at right angles to the alidade, the line of sight is parallel to the fiducial edge only for (A) Horizontal sights (B) Inclined sights upward (C) Inclined sight downward (D) None of these

Description : If the plane table is not horizontal in a direction at right angles to the alidade, the line of sight is parallel to the fiducial edge only for (A) Horizontal sights (B) Inclined sights upward (C) Inclined sight downward (D) None of these

Last Answer : (A) Horizontal sights

What are the pros and cons of a brick foundation in a house?

Description : What are the pros and cons of a brick foundation in a house?

Last Answer : answer:I am not a structural engineer, but I would expect there is a way to make them earthquake safe. It may not be economical, depending on where you live, but it is very likely ... codes. A structural engineer would be able to make recommendations on the best solution for your specific project.

A square surface 3 m × 3 m lies in a vertical line in water pipe its upper edge at water surface. The hydrostatic force on square surface is (A) 9,000 kg (B) 13,500 kg (C) 18,000 kg (D) 27,000 kg

Description : A square surface 3 m × 3 m lies in a vertical line in water pipe its upper edge at water surface. The hydrostatic force on square surface is (A) 9,000 kg (B) 13,500 kg (C) 18,000 kg (D) 27,000 kg

Last Answer : Answer: Option B

An R.C.C. lintel is spanning an opening of 2 m span in a brick wall. The height of the roof is 2.9 m above the floor level and that of the opening is 2.1 m above the floor level. The lintel is to be designed for self weight plus (A) Triangular load of the wall (B) UDL of wall (C) UDL of wall + load from the roof (D) Triangular load + load from the roof

Description : An R.C.C. lintel is spanning an opening of 2 m span in a brick wall. The height of the roof is 2.9 m above the floor level and that of the opening is 2.1 m above the floor level. The lintel is to be ... (B) UDL of wall (C) UDL of wall + load from the roof (D) Triangular load + load from the roof

Last Answer : Answer: Option C

The expected out turn of half brick partition wall per mason per day is (A) 1.5 m3 (B) 2.0 m3 (C) 4.0 m2 (D) 5.0 m2

Description : The expected out turn of half brick partition wall per mason per day is (A) 1.5 m3 (B) 2.0 m3 (C) 4.0 m2 (D) 5.0 m2

Last Answer : (B) 2.0 m3

Brick walls are measured in sq. m if the thickness of the wall is (A) 10 cm (B) 15 cm (C) 20 cm (D) None of these

Description : Brick walls are measured in sq. m if the thickness of the wall is (A) 10 cm (B) 15 cm (C) 20 cm (D) None of these

Last Answer : (A) 10 cm

Pick up the correct statement from the following: (A) The breakwater which can be used as a platform for loading and unloading of cargo is called a mole (B) The brick masonry retaining wall which is used for loading and unloading of cargo is called quay wall (C) Three types of break waters are generally provided in harbours (D) All of the above

Description : Pick up the correct statement from the following: (A) The breakwater which can be used as a platform for loading and unloading of cargo is called a mole (B) The brick masonry retaining wall which is ... wall (C) Three types of break waters are generally provided in harbours (D) All of the above

Last Answer : (D) All of the above

Minimum thickness of wall where single Flemish bond can be used is (A) Half brick thick (B) One brick thick (C) One and a half bricks thick (D) Two bricks thick

Description : Minimum thickness of wall where single Flemish bond can be used is (A) Half brick thick (B) One brick thick (C) One and a half bricks thick (D) Two bricks thick

Last Answer : Answer: Option C

A queen closer is a (A) Brick laid with its length parallel to the face or direction of wall (B) Brick laid with its breadth parallel to the face or direction of wall (C) Brick having the same length and depth as the other bricks but half the breadth (D) Brick with half the width at one end and full width at the other

Description : A queen closer is a (A) Brick laid with its length parallel to the face or direction of wall (B) Brick laid with its breadth parallel to the face or direction of wall (C) Brick having the same ... bricks but half the breadth (D) Brick with half the width at one end and full width at the other

Last Answer : Answer: Option C

The stretcher bond in brick masonry can be used only when the thickness of wall is (A) 90 mm (B) 180 mm (C) 190 mm (D) 280 mm

Description : The stretcher bond in brick masonry can be used only when the thickness of wall is (A) 90 mm (B) 180 mm (C) 190 mm (D) 280 mm

Last Answer : Answer: Option A

The brick laid with its length parallel to the face of a wall, is a known as (A) Header (B) Stretcher (C) Closer (D) None of the

Description : The brick laid with its length parallel to the face of a wall, is a known as (A) Header (B) Stretcher (C) Closer (D) None of the

Last Answer : Answer: Option B

The brick laid with its breadth parallel to the face of a wall, is known as (A) Header (B) Stretcher (C) Closer (D) None of these

Description : The brick laid with its breadth parallel to the face of a wall, is known as (A) Header (B) Stretcher (C) Closer (D) None of these

Last Answer : Answer: Option A

The 9 cm × 9 cm side of a brick as seen in the wall face, is generally known as (A) Stretcher (B) Face (C) Front (D) Heade

Description : The 9 cm × 9 cm side of a brick as seen in the wall face, is generally known as (A) Stretcher (B) Face (C) Front (D) Heade

Last Answer : Answer: Option D