Normalising does not __________ of a metal. (A) Improve machinability & tensile strength (B) Remove internal stresses (C) Refine the structure (D) Remove strains caused by cold working

Normalising does not __________ of a metal.
(A) Improve machinability & tensile strength
(B) Remove internal stresses
(C) Refine the structure
(D) Remove strains caused by cold working
by

1 Answer

Answer :

Option B
by

Related questions

Normalising of a casting does not (A) Induce stresses in it (B) Refine its grain structure (C) Reduce segregation (D) Improve its mechanical properties

Description : Normalising of a casting does not (A) Induce stresses in it (B) Refine its grain structure (C) Reduce segregation (D) Improve its mechanical properties

Last Answer : (A) Induce stresses in it

Normalising of an object does not (A) Refine coarse grain structure obtained during hot working (B) Improve ductility (C) Improve yield strength (D) Improve mechanical properties

Description : Normalising of an object does not (A) Refine coarse grain structure obtained during hot working (B) Improve ductility (C) Improve yield strength (D) Improve mechanical properties

Last Answer : (B) Improve ductility

Pick out the correct statement. (A) Hot worked materials are subjected to annealing to remove internal stresses (B) Annealing of steel hardens it slightly (C) Normalising of a material induces stresses (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness

Description : Pick out the correct statement. (A) Hot worked materials are subjected to annealing to remove internal stresses (B) Annealing of steel hardens it slightly (C) Normalising of a material induces stresses (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness

Last Answer : (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness Share

. To improve the machinability of steel, it is generally subjected to (A) Spheroidising (B) Tempering (C) Normalising (D) Annealing

Description : . To improve the machinability of steel, it is generally subjected to (A) Spheroidising (B) Tempering (C) Normalising (D) Annealing

Last Answer : (A) Spheroidising

o improve the machinability of steel, it is generally subjected to (A) Spheroidising (B) Tempering (C) Normalising (D) Annealing

Description : o improve the machinability of steel, it is generally subjected to (A) Spheroidising (B) Tempering (C) Normalising (D) Annealing

Last Answer : Option A

When the steel is subjected to normalising, its __________ decreases. (A) Yield point (B) Ductility (C) Ultimate tensile strength (UTS)

Description : When the steel is subjected to normalising, its __________ decreases. (A) Yield point (B) Ductility (C) Ultimate tensile strength (UTS)

Last Answer : (B) Ductility

To improve the machinability of steel by its softening, it is subjected to (A) Cold working (B) Annealing (C) Shot blasting (D) Heating

Description : To improve the machinability of steel by its softening, it is subjected to (A) Cold working (B) Annealing (C) Shot blasting (D) Heating

Last Answer : (B) Annealing

Machinability of hard alloys and tool steels is improved by (A) Spheroidising (B) Annealing (C) Tempering (D) Normalising

Description : Machinability of hard alloys and tool steels is improved by (A) Spheroidising (B) Annealing (C) Tempering (D) Normalising

Last Answer : Option B

Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength

Description : Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength

Last Answer : (C) Machinability

__________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength. (A) Lancing (B) Shot peening (C) Slugging (D) Spinning

Description : __________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength. (A) Lancing (B) Shot peening (C) Slugging (D) Spinning

Last Answer : (B) Shot peening

Which of the following is (are) true? (A) Cast iron has poor tensile strength compared to steel (B) Failure of cast iron flywheel is sudden and total (C) Machinability of cast iron flywheel is poor compared to steel flywheel (D) All of the above

Description : Which of the following is (are) true? (A) Cast iron has poor tensile strength compared to steel (B) Failure of cast iron flywheel is sudden and total (C) Machinability of cast iron flywheel is poor compared to steel flywheel (D) All of the above

Last Answer : (D) All of the above

Define: i)Tensile strength ii) Machinability

Description : Define: i)Tensile strength ii) Machinability

Last Answer : i) Tensile strength: It is the ability or capacity of a metal to carry the load without breaking. Or A tensile strength of a metal is its ability to resist pull without breaking.  ii) Machinability: ... can be easily cut by cutting tools to produce a desired shape & surface finish on its surface. 

Lead is added to 60:40 brass primarily to improve (A) Machinability (B) Corrosion resistance (C) Fluidity (D) Strength

Description : Lead is added to 60:40 brass primarily to improve (A) Machinability (B) Corrosion resistance (C) Fluidity (D) Strength

Last Answer : (A) Machinability

Tempering of a material does not improve its (A) Machinability (B) Toughness (C) Internal stress level (D) Softness

Description : Tempering of a material does not improve its (A) Machinability (B) Toughness (C) Internal stress level (D) Softness

Last Answer : A) Machinability

Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance

Description : Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance

Last Answer : (A) Impact strength

Stresses encountered in the metal forming processes are less than the __________ of the material. (A) Fracture strength (B) Yield strength(C) Elastic limit (D) Limit of proportionality

Description : Stresses encountered in the metal forming processes are less than the __________ of the material. (A) Fracture strength (B) Yield strength (C) Elastic limit (D) Limit of proportionality

Last Answer : Option A

Plasticisers are added to polymers to improve their (A) Tensile strength (B) Softness & flexibility (C) Acid resistance (D) Alkali resistance

Description : Plasticisers are added to polymers to improve their (A) Tensile strength (B) Softness & flexibility (C) Acid resistance (D) Alkali resistance

Last Answer : (B) Softness & flexibility

Pick out the wrong statement about the machinability of metals. Machinability of a metal (A) Decreases with increase in strain hardening tendencies (B) Decreases with increase in hardness, in general (C) Depend on the composition, microstructure and physical & mechanical

Description : Pick out the wrong statement about the machinability of metals. Machinability of a metal (A) Decreases with increase in strain hardening tendencies (B) Decreases with increase in hardness, in general (C) Depend on the composition, microstructure and physical & mechanical

Last Answer : Option C

Heating the Hypo-eutectoid steels to 30°C above the upper critical temperature line, soaking at that temperature and then cooling slowly to the room temperature to form a pearlite & ferrite structure is called (A) Tempering (B) Hardening (C) Annealing (D) Normalising

Description : Heating the Hypo-eutectoid steels to 30°C above the upper critical temperature line, soaking at that temperature and then cooling slowly to the room temperature to form a pearlite & ferrite structure is called (A) Tempering (B) Hardening (C) Annealing (D) Normalising

Last Answer : Option C

The compatibility conditions in terms of strains in a two-dimensional problem are associated with (a) Stresses (b) Forces (c) Properties of materials (d) Deformations

Description : The compatibility conditions in terms of strains in a two-dimensional problem are associated with (a) Stresses (b) Forces (c) Properties of materials (d) Deformations

Last Answer : Deformations

The period of adolescence is known as a period of stresses and strains. It is the most difficult and the awkward period, and marks the reawakening of the repressed sex-impulse. Which type of behavior is unwanted? (a) Attitude of independence (b) Sympathetic understanding (c) Silence and hush-hush policy (d) None of the above.

Description : The period of adolescence is known as a period of stresses and strains. It is the most difficult and the awkward period, and marks the reawakening of the repressed sex-impulse. Which type of behavior is ... (b) Sympathetic understanding (c) Silence and hush-hush policy (d) None of the above.

Last Answer : (c) Silence and hush-hush policy

Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen. (A) Creep (B) Fatigue (C) Endurance (D) Tensile

Description : Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen. (A) Creep (B) Fatigue (C) Endurance (D) Tensile

Last Answer : (B) Fatigue

Addition of nickel to copper improves its (A) Machinability (B) Ductility (C) Strength (D) Hardness

Description : Addition of nickel to copper improves its (A) Machinability (B) Ductility (C) Strength (D) Hardness

Last Answer : (D) Hardness

Plastics as a material of construction suffer from the drawback of low (A) Machinability (B) Density (C) Strength (D) Plastic deformatio

Description : Plastics as a material of construction suffer from the drawback of low (A) Machinability (B) Density (C) Strength (D) Plastic deformatio

Last Answer : Option C

__________ of a material results, when its strength is increased & ductility is decreased by heating at a relatively lower temperature after cold working. (A) Solid solution hardening (B) Screw dislocation (C) Strain ageing (D) Twinning

Description : __________ of a material results, when its strength is increased & ductility is decreased by heating at a relatively lower temperature after cold working. (A) Solid solution hardening (B) Screw dislocation (C) Strain ageing (D) Twinning

Last Answer : (C) Strain ageing

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (C) Creep resistance

With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Description : With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Last Answer : (A) Impact strength

In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases. (A) Percentage elongation (B) Brinell hardness (C) Tensile strength (D) All 'a', 'b' & 'c'

Description : In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases. (A) Percentage elongation (B) Brinell hardness (C) Tensile strength (D) All 'a', 'b' & 'c'

Last Answer : (A) Percentage elongation

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

A metal contains, metal oxide as impurity. The method used to refine this metal is

Description : A metal contains, metal oxide as impurity. The method used to refine this metal is

Last Answer : A metal contains, metal oxide as impurity. The method used to refine this metal is A. Poling B. Liqation C. Cupellation D. Distallation

The heat treatment process applied to cold formed steel parts is (A) Normalising (B) Tempering (C) Artificial ageing (D) Solution annealing

Description : The heat treatment process applied to cold formed steel parts is (A) Normalising (B) Tempering (C) Artificial ageing (D) Solution annealing

Last Answer : (D) Solution annealing

The heat treatment process to which castings and the steel balls produced by cold heading are subjected is (A) Tempering (B) Normalising (C) Annealing (D) None of these

Description : The heat treatment process to which castings and the steel balls produced by cold heading are subjected is (A) Tempering (B) Normalising (C) Annealing (D) None of these

Last Answer : (B) Normalising

Cold worked steel parts are normally subjected to (A) Normalising (B) Hardening (C) Annealing (D) Shot peening

Description : Cold worked steel parts are normally subjected to (A) Normalising (B) Hardening (C) Annealing (D) Shot peening

Last Answer : (C) Annealing

In cold working of metal as compared to its hot working (A) Cracks and blow holes are eliminated (B) Ductility and impact strength improves (C) Appreciable strain hardening is produced (D) Yield stress, hardness and fatigue strength is not at all affected

Description : In cold working of metal as compared to its hot working (A) Cracks and blow holes are eliminated (B) Ductility and impact strength improves (C) Appreciable strain hardening is produced (D) Yield stress, hardness and fatigue strength is not at all affected

Last Answer : (C) Appreciable strain hardening is produced

Pick out the wrong statement. (A) The toughness of a material decreases, when it is heated (B) Crane hooks are normally made of wrought iron (C) Cold working of a metal decreases its fatigue strength (D) The temperature at which new grains are formed in a metal is known as the recrystallisation temperature

Description : Pick out the wrong statement. (A) The toughness of a material decreases, when it is heated (B) Crane hooks are normally made of wrought iron (C) Cold working of a metal decreases its ... (D) The temperature at which new grains are formed in a metal is known as the recrystallisation temperature

Last Answer : (C) Cold working of a metal decreases its fatigue strength

Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Description : Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Last Answer : (A) Modulus of elasticity (young's modulus)

To remove dirt from the flowing fluid, we use a (A) Coagulant (B) Gravity settler (C) Strains (D) Clarifier

Description : To remove dirt from the flowing fluid, we use a (A) Coagulant (B) Gravity settler (C) Strains (D) Clarifier

Last Answer : (C) Strains

Addition of __________ to steel does not help in improving its machinability. (A) Sulphur (B) Silicon (C) Lead (D) Phosphorous

Description : Addition of __________ to steel does not help in improving its machinability. (A) Sulphur (B) Silicon (C) Lead (D) Phosphorous

Last Answer : (B) Silicon

Addition of __________ to steel does not help in improving its machinability. (A) Sulphur (B) Silicon (C) Lead (D) Phosphorous

Description : Addition of __________ to steel does not help in improving its machinability. (A) Sulphur (B) Silicon (C) Lead (D) Phosphorous

Last Answer : Option B

Vulcanisation of rubber decreases its (A) Tensile strength (B) Resistance to organic solvents (C) Tackiness (D) Working temperature range

Description : Vulcanisation of rubber decreases its (A) Tensile strength (B) Resistance to organic solvents (C) Tackiness (D) Working temperature range

Last Answer : (C) Tackiness

Hollow shafts can be made as strong as solid shafts by making the twisting moments of both the shafts same. Shafts made by __________ have residual stresses. (A) Forging (B) Cold rolling (C) Hot rolling (D) Casting

Description : Hollow shafts can be made as strong as solid shafts by making the twisting moments of both the shafts same. Shafts made by __________ have residual stresses. (A) Forging (B) Cold rolling (C) Hot rolling (D) Casting

Last Answer : (B) Cold rolling

Globular form of cementite is formed during the __________ process. (A) Spheroidising (B) Hardening (C) Annealing (D) Normalising

Description : Globular form of cementite is formed during the __________ process. (A) Spheroidising (B) Hardening (C) Annealing (D) Normalising

Last Answer : (B) Hardening

Spheroidising of a material is a/an __________ process. (A) Normalising (B) Annealing (C) Tempering (D) Hardening

Description : Spheroidising of a material is a/an __________ process. (A) Normalising (B) Annealing (C) Tempering (D) Hardening

Last Answer : (B) Annealing

__________ of hard alloy and tool steel is done to make it easily machinable. (A) Case carburising (B) Tempering (C) Normalising (D) Annealing

Description : __________ of hard alloy and tool steel is done to make it easily machinable. (A) Case carburising (B) Tempering (C) Normalising (D) Annealing

Last Answer : (B) Tempering

Which of the following has high tensile strength? (A) Plain hot rolled wires (B) Cold drawn wires (C) Heat treated rolled wires (D) All have same tensile strength

Description : Which of the following has high tensile strength? (A) Plain hot rolled wires (B) Cold drawn wires (C) Heat treated rolled wires (D) All have same tensile strength

Last Answer : Answer: Option B

Aerodynamic noise resulting from turbulent gas flow is the most prevalent source of valve noise in fluid flow control. It is caused due to (A) Reynold stresses (B) Shear forces (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Aerodynamic noise resulting from turbulent gas flow is the most prevalent source of valve noise in fluid flow control. It is caused due to (A) Reynold stresses (B) Shear forces (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

The property due to which a metal can be hammered into thin sheets without breaking is _______. a) malleability b)ductility c)tensile strength d)conductivity

Description : The property due to which a metal can be hammered into thin sheets without breaking is _______. a) malleability b)ductility c)tensile strength d)conductivity

Last Answer : a) malleability

What property of a metal describes the onset of plastic deformation in a tensile test? w) tensile strength x) elongation y) yield strength z) reduction in area

Description : What property of a metal describes the onset of plastic deformation in a tensile test? w) tensile strength x) elongation y) yield strength z) reduction in area

Last Answer : ANSWER: Y -- YIELD STRENGTH

__________ is used for determining the tensile strength of steels. (A) Hydraulic press (B) Universal testing machine (C) Mechanical press (D) None of these

Description : __________ is used for determining the tensile strength of steels. (A) Hydraulic press (B) Universal testing machine (C) Mechanical press (D) None of these

Last Answer : (B) Universal testing machine