. Thermal efficiency of an internal combustion engine is around __________ percent. (A) 8 (B) 35 (C) 65 (D) 80

. Thermal efficiency of an internal combustion engine is around
__________ percent.
(A) 8
(B) 35
(C) 65
(D) 80
by

1 Answer

Answer :

Option B
by

Related questions

Thermal efficiency of an internal combustion engine is around __________ percent. (A) 8 (B) 35 (C) 65

Description : Thermal efficiency of an internal combustion engine is around __________ percent. (A) 8 (B) 35 (C) 65

Last Answer : Option B

Thermal efficiency of a limestone calcination rotary kiln may be around __________ percent. (A) 20 (B) 40 (C) 65 (D) 80

Description : Thermal efficiency of a limestone calcination rotary kiln may be around __________ percent. (A) 20 (B) 40 (C) 65 (D) 80

Last Answer : (B) 40

Carbon content in plain carbon steel is __________ percent. (A) 0.1 to 0.15 (B) 0.35 to 0.45 (C) 0.65 to 0.80 (D) 0.85 to 1.2

Description : Carbon content in plain carbon steel is __________ percent. (A) 0.1 to 0.15 (B) 0.35 to 0.45 (C) 0.65 to 0.80 (D) 0.85 to 1.2

Last Answer : (B) 0.35 to 0.45

Equipment installation cost in a chemical process plant ranges from __________ percent of the purchased equipment cost. (A) 10 to 20 (B) 35 to 45 (C) 55 to 65 (D) 70 to 80

Description : Equipment installation cost in a chemical process plant ranges from __________ percent of the purchased equipment cost. (A) 10 to 20 (B) 35 to 45 (C) 55 to 65 (D) 70 to 80

Last Answer : (B) 35 to 45

Thermal efficiency of an internal combustion engine on weak mixture is a. higher b. lower c. unaffected d. unpredictable

Description : Thermal efficiency of an internal combustion engine on weak mixture is a. higher b. lower c. unaffected d. unpredictable

Last Answer : ANSWER a. higher

The heat exhaust of an automobile with an internal combustion engine represents approximately what percent of the energy of the original fuel? w) 10 % x) 50 % y) 35 % z) 5 %

Description : The heat exhaust of an automobile with an internal combustion engine represents approximately what percent of the energy of the original fuel? w) 10 % x) 50 % y) 35 % z) 5 % 

Last Answer : ANSWER: Y -- 35 % 

Maximum thermal efficiency of boiler may be about __________ percent. (A) 10 (B) 25 (C) 65 (D) 90

Description : Maximum thermal efficiency of boiler may be about __________ percent. (A) 10 (B) 25 (C) 65 (D) 90

Last Answer : (D) 90

Overall thermal efficiency of a lumpy coal fired suitably designed heating furnace, if operated & maintained properly may be about __________ percent. (A) 10-15 (B) 25-30 (C) 45-50 (D) 65-70

Description : Overall thermal efficiency of a lumpy coal fired suitably designed heating furnace, if operated & maintained properly may be about __________ percent. (A) 10-15 (B) 25-30 (C) 45-50 (D) 65-70

Last Answer : (B) 25-30

The thermal efficiency of an air/fuel gas preheating recuperator may be as high as __________ percent. (A) 50 (B) 65 (C) 85 (D) 99

Description : The thermal efficiency of an air/fuel gas preheating recuperator may be as high as __________ percent. (A) 50 (B) 65 (C) 85 (D) 99

Last Answer : (C) 85

Thermal efficiency of blast furnace stoves used for heating blast (air) may be about __________ percent. (A) 20 (B) 40 (C) 60 (D) 80

Description : Thermal efficiency of blast furnace stoves used for heating blast (air) may be about __________ percent. (A) 20 (B) 40 (C) 60 (D) 80

Last Answer : (D) 80

Thermal efficiency of an open hearth furnace may be about __________ percent. (A) 5 (B) 20 (C) 50 (D) 80

Description : Thermal efficiency of an open hearth furnace may be about __________ percent. (A) 5 (B) 20 (C) 50 (D) 80

Last Answer : (B) 20

Abrasion index of blast furnace coke should be around __________ percent. (A) 20 (B) 35 (C) 55 (D) 80

Description : Abrasion index of blast furnace coke should be around __________ percent. (A) 20 (B) 35 (C) 55 (D) 80

Last Answer : (D) 80

Furnace oil consumption in a furnace for a given duty employing preheated combination air (at 300°) may be reduced by about __________ percent as compared to the use of atmospheric combustion air. (A) 5 (B) 10 (C) 20 (D) 35

Description : Furnace oil consumption in a furnace for a given duty employing preheated combination air (at 300°) may be reduced by about __________ percent as compared to the use of atmospheric combustion air. (A) 5 (B) 10 (C) 20 (D) 35

Last Answer : (C) 20

P2O5 content in superphosphate is about __________ percent. (A) 30-35 (B) 15-20 (C) 65-70 (D) 85-90

Description : P2O5 content in superphosphate is about __________ percent. (A) 30-35 (B) 15-20 (C) 65-70 (D) 85-90

Last Answer : (B) 15-20

For heavier fuels the cooling system of an internal combustion engine, the temperature is maintained at a) 78 to 80°C b) 80 to 84 °C c) 85 to 88°C d) 88 to 90°C

Description : For heavier fuels the cooling system of an internal combustion engine, the temperature is maintained at a) 78 to 80°C b) 80 to 84 °C c) 85 to 88°C d) 88 to 90°C

Last Answer : d) 88 to 90°C

If the temperature of intake air in internal combustion engine is lowered, the efficiency will a. increase b. decrease c. remains same d. increases upto certain limit and then decrease

Description : If the temperature of intake air in internal combustion engine is lowered, the efficiency will a. increase b. decrease c. remains same d. increases upto certain limit and then decrease

Last Answer : ANSWER a. increase

The efficiency of a internal combustion engine normally is of the order of a. 15-20 % b. 20-25% c. 25-30% d. 30-35%

Description : The efficiency of a internal combustion engine normally is of the order of a. 15-20 % b. 20-25% c. 25-30% d. 30-35%

Last Answer : ANSWER d. 30-35%

If the intake air temperature of Internal combustion engine increases, its efficiency will a. increase b. decrease c.remains same d unpredictable

Description : If the intake air temperature of Internal combustion engine increases, its efficiency will a. increase b. decrease c.remains same d unpredictable

Last Answer : ANSWER b. decrease

Iron content in Indian iron ore is about __________ percent. (A) 80-85 (B) 60-65 (C) 40-45 (D) 20-25

Description : Iron content in Indian iron ore is about __________ percent. (A) 80-85 (B) 60-65 (C) 40-45 (D) 20-25

Last Answer : (B) 60-65

Which statement of the second law of thermodynamics states that no heat engine can have a thermal efficiency of 100 percent?  A. Kelvin-Planck statement  B. Clausius statement  C. Kevin statement  D. Rankine statement

Description : Which statement of the second law of thermodynamics states that no heat engine can have a thermal efficiency of 100 percent?  A. Kelvin-Planck statement  B. Clausius statement  C. Kevin statement  D. Rankine statement

Last Answer : Kelvin-Planck statement

Grinding efficiency of a ball mill is of the order of __________ percent. (A) 1-5 (B) 40-50 (C) 75-80 (D) 90-95

Description : Grinding efficiency of a ball mill is of the order of __________ percent. (A) 1-5 (B) 40-50 (C) 75-80 (D) 90-95

Last Answer : (A) 1-5

The thermal efficiency of a steel slab reheating furnace (walking beam type) may be about __________ percent. (A) 15 (B) 40 (C) 70 (D) 85

Description : The thermal efficiency of a steel slab reheating furnace (walking beam type) may be about __________ percent. (A) 15 (B) 40 (C) 70 (D) 85

Last Answer : (B) 40

Oxygen content in a flue gas was found to be 4%. It implies that excess air used for combustion was around __________ percent. (A) 4 (B) 96 (C) 20 (D) 40

Description : Oxygen content in a flue gas was found to be 4%. It implies that excess air used for combustion was around __________ percent. (A) 4 (B) 96 (C) 20 (D) 40

Last Answer : (C) 20

Yield of pitch from distillation of high temperature tar is around __________ percent. (A) 10 (B) 25 (C) 65 (D) 90

Description : Yield of pitch from distillation of high temperature tar is around __________ percent. (A) 10 (B) 25 (C) 65 (D) 90

Last Answer : (C) 65

150. Nitrogen content in ammonium sulphate (a fertiliser) is around __________ percent. (A) 5 (B) 20 (C) 50 (D) 65

Description : 150. Nitrogen content in ammonium sulphate (a fertiliser) is around __________ percent. (A) 5 (B) 20 (C) 50 (D) 65

Last Answer : (B) 20

Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Description : Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Shatter index of metallurgical coke on 2 inches and 0.5 inch screen should be respectively around __________ percent. (A) 80 and 97 (B) 95 and 100 (C) 40 and 70 (D) 25 and 97

Description : Shatter index of metallurgical coke on 2 inches and 0.5 inch screen should be respectively around __________ percent. (A) 80 and 97 (B) 95 and 100 (C) 40 and 70 (D) 25 and 97

Last Answer : (A) 80 and 97

Sucrose content in cane sugar may be around __________ percent. (A) 50 (B) 70 (C) 95(D) 80

Description : Sucrose content in cane sugar may be around __________ percent. (A) 50 (B) 70 (C) 95 (D) 80

Last Answer : (C) 95

Carbon content of pitch (residue of coal tar distillation) is around __________ percent. (A) 70 (B) 55(C) 80 (D) 94

Description : Carbon content of pitch (residue of coal tar distillation) is around __________ percent. (A) 70 (B) 55 (C) 80 (D) 94

Last Answer : (D) 94

What is defined as the ratio of the net electrical power output to the rate of fuel energy input?  A. Combustion efficiency  B. Thermal efficiency  C. Overall efficiency  D. Furnace efficiency

Description : What is defined as the ratio of the net electrical power output to the rate of fuel energy input?  A. Combustion efficiency  B. Thermal efficiency  C. Overall efficiency  D. Furnace efficiency

Last Answer : Overall efficiency

Mode of heat transfer involved in the cooling of air cooled internal combustion engine is (A) Conduction(B) Natural convection(C) Forced convection(D) None of these

Description : Mode of heat transfer involved in the cooling of air cooled internal combustion engine is (A) Conduction (B) Natural convection (C) Forced convection (D) None of these

Last Answer : (B) Natural convection

Efficiency of external combustion/steam engine is low.

Description :  Efficiency of external combustion/steam engine is low.

Last Answer : Efficiency of steam engine is low as there is more loss of heat. Most of the heat is lost in boiling of water to increase the temperature of water to its boiling point.

A typical yield of diesel in straight run distillation of crude oil may be about __________ percent. (A) 8 (B) 18 (C) 28 (D) 35

Description : A typical yield of diesel in straight run distillation of crude oil may be about __________ percent. (A) 8 (B) 18 (C) 28 (D) 35

Last Answer : (A) 8

High speed cutting tool steels contain about __________ percent of tungsten. (A) 6-8 (B) 18-20 (C) 30-35 (D) 50-55

Description : High speed cutting tool steels contain about __________ percent of tungsten. (A) 6-8 (B) 18-20 (C) 30-35 (D) 50-55

Last Answer : (B) 18-20

The thermal efficiency of a reversible heat engine operating between two given thermal reservoirs is 0.4. The device is used either as a refrigerator or as a heat pump between the same reservoirs. Then the coefficient of performance as a refrigerator (COP)R and the co-efficient of performance as a heat pump (COP)HP are (A) (COP)R = (COP)HP = 0.6 (B) (COP)R = 2.5; (COP)HP = 1.5 (C) (COP)R = 1.5; (COP)HP = 2.5 (D) (COP)R = (COP)HP = 2.5

Description : The thermal efficiency of a reversible heat engine operating between two given thermal reservoirs is 0.4. The device is used either as a refrigerator or as a heat pump between the same reservoirs. Then the coefficient of performance as a ... )R = 1.5; (COP)HP = 2.5 (D) (COP)R = (COP)HP = 2.5

Last Answer : (C) (COP)R = 1.5; (COP)HP = 2.5

The following heat engine produces power of 100,000 kW. The heat engine operates between 800 K and 300 K. It has a thermal efficiency equal to 50% of that of the Carnot engine for the same temperature. The rate at which heat is absorbed from the hot reservoir is (A) 100,000 kW (B) 160,000 kW (C) 200,000 kW (D) 320,000 kW

Description : The following heat engine produces power of 100,000 kW. The heat engine operates between 800 K and 300 K. It has a thermal efficiency equal to 50% of that of the Carnot engine for the same temperature. The rate at which heat is ... is (A) 100,000 kW (B) 160,000 kW (C) 200,000 kW (D) 320,000 kW

Last Answer : (D) 320,000 kW

Which of the following has the least thermal efficiency? (A) Steam engine (B) Carnot engine (C) Diesel engine (D) Otto engine

Description : Which of the following has the least thermal efficiency? (A) Steam engine (B) Carnot engine (C) Diesel engine (D) Otto engine

Last Answer : A) Steam engine

Thermal efficiency of a Carnot engine can approach 100%, only when the temperature of the (A) Cold reservoir approaches zero (B) Hot reservoir approaches infinity (C) Either (A) or (B) (D) Neither (A) nor (B)

Description : Thermal efficiency of a Carnot engine can approach 100%, only when the temperature of the (A) Cold reservoir approaches zero (B) Hot reservoir approaches infinity (C) Either (A) or (B) (D) Neither (A) nor (B)

Last Answer : C) Either (A) or (B)

Pick out the wrong statement. (A) Trouton's ratio of non-polar liquids is calculated using Kistyakowsky equation (B) Thermal efficiency of a Carnot engine is always less than 1 (C) An equation relating pressure, volume and temperature of a gas is called ideal gas equation (D) None of these

Description : Pick out the wrong statement. (A) Trouton's ratio of non-polar liquids is calculated using Kistyakowsky equation (B) Thermal efficiency of a Carnot engine is always less than 1 (C) An equation relating pressure, volume and temperature of a gas is called ideal gas equation (D) None of these

Last Answer : (C) An equation relating pressure, volume and temperature of a gas is called ideal gas equation

Efficiency of power transmission (η) through a circular pipe is given by (ht - hf )/ht , which has a maximum value of __________ percent. (A) 33:3 (B) 50 (C) 66.6 (D) 88.8

Description : Efficiency of power transmission (η) through a circular pipe is given by (ht - hf )/ht , which has a maximum value of __________ percent. (A) 33:3 (B) 50 (C) 66.6 (D) 88.8

Last Answer : (C) 66.6

Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Description : Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Last Answer : (B) 130

Efficiency of the combustion of a fuel is judged by the __________ the flue gas. (A) % of CO2 in (B) % of O2 in (C) Temperature of (D) Colour of

Description : Efficiency of the combustion of a fuel is judged by the __________ the flue gas. (A) % of CO2 in (B) % of O2 in (C) Temperature of (D) Colour of

Last Answer : (B) % of O2 in

High sulphur content in a fuel __________ of the flue gases. (A) Decreases the dew point (B) Increases the dew point (C) Reduces the combustion efficiency by limiting the permissible temperature reduction (D) Both (B) and (C)

Description : High sulphur content in a fuel __________ of the flue gases. (A) Decreases the dew point (B) Increases the dew point (C) Reduces the combustion efficiency by limiting the permissible temperature reduction (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Was an accelerator an original component of the internal combustion engine?

Description : Was an accelerator an original component of the internal combustion engine?

Last Answer : No and it still isn’t. Look up the definition.

Can you describe the process by which a modern internal combustion automobile engine is designed?

Description : Can you describe the process by which a modern internal combustion automobile engine is designed?

Last Answer : Well, I say it’s designed to function as certain shape to fit a certain area, once that’s all worked out it does this

In the quest for a clean, fuel-efficient engine,why hasn't this technology,EVC,been implemented in today's modern internal combustion engine?

Description : In the quest for a clean, fuel-efficient engine,why hasn't this technology,EVC,been implemented in today's modern internal combustion engine?

Last Answer : answer:Oh this is near and dear to my heart. I had the misfortune of actually doing this analysis for my employer about 10 years ago. Virtually every manufacturer has built and tested units like this. ... is hard for customers to justify the purchase. Believe me if they could sell it, they would.

How would you wish to travel if the internal combustion engine were a figment of our imagination?

Description : How would you wish to travel if the internal combustion engine were a figment of our imagination?

Last Answer : Jaunting! (Like in Alfred Bester’s book “The Stars My Destination.”) Teleportation is cool!

Who patents the internal combustion Engine?

Description : Who patents the internal combustion Engine?

Last Answer : Samuel Morey.

What does cc stand for in a internal combustion engine?

Description : What does cc stand for in a internal combustion engine?

Last Answer : Feel Free to Answer

The most popular firing order in a 4-cylinder inline internal combustion engine is a. 1-2-3-4 b. 1-3-2-4 c. 1-3-4-2 d. 1-2-4-3

Description : The most popular firing order in a 4-cylinder inline internal combustion engine is a. 1-2-3-4 b. 1-3-2-4 c. 1-3-4-2 d. 1-2-4-3

Last Answer : ANSWER b. 1-3-4-2