Thermal efficiency of an open hearth furnace may be about __________ percent. (A) 5 (B) 20 (C) 50 (D) 80

Thermal efficiency of an open hearth furnace may be about __________
percent.
(A) 5
(B) 20
(C) 50
(D) 80
by

1 Answer

Answer :

(B) 20
by

Related questions

Thermal efficiency of blast furnace stoves used for heating blast (air) may be about __________ percent. (A) 20 (B) 40 (C) 60 (D) 80

Description : Thermal efficiency of blast furnace stoves used for heating blast (air) may be about __________ percent. (A) 20 (B) 40 (C) 60 (D) 80

Last Answer : (D) 80

Overall thermal efficiency of a lumpy coal fired suitably designed heating furnace, if operated & maintained properly may be about __________ percent. (A) 10-15 (B) 25-30 (C) 45-50 (D) 65-70

Description : Overall thermal efficiency of a lumpy coal fired suitably designed heating furnace, if operated & maintained properly may be about __________ percent. (A) 10-15 (B) 25-30 (C) 45-50 (D) 65-70

Last Answer : (B) 25-30

Thermal efficiency of a limestone calcination rotary kiln may be around __________ percent. (A) 20 (B) 40 (C) 65 (D) 80

Description : Thermal efficiency of a limestone calcination rotary kiln may be around __________ percent. (A) 20 (B) 40 (C) 65 (D) 80

Last Answer : (B) 40

The thermal efficiency of a steel slab reheating furnace (walking beam type) may be about __________ percent. (A) 15 (B) 40 (C) 70 (D) 85

Description : The thermal efficiency of a steel slab reheating furnace (walking beam type) may be about __________ percent. (A) 15 (B) 40 (C) 70 (D) 85

Last Answer : (B) 40

Neutral atmosphere is maintained in a/an __________ furnace. (A) Cold rolled steel coil annealing (B) Open hearth (C) Soaking pit (D) Walking beam reheating

Description : Neutral atmosphere is maintained in a/an __________ furnace. (A) Cold rolled steel coil annealing (B) Open hearth (C) Soaking pit (D) Walking beam reheating

Last Answer : (A) Cold rolled steel coil annealing

__________ is an indirectly heated furnace. (A) Open hearth furnace (B) Muffle furnace (C) Soaking pit (D) Reheating furnace

Description : __________ is an indirectly heated furnace. (A) Open hearth furnace (B) Muffle furnace (C) Soaking pit (D) Reheating furnace

Last Answer : (B) Muffle furnace

The thermal efficiency of an air/fuel gas preheating recuperator may be as high as __________ percent. (A) 50 (B) 65 (C) 85 (D) 99

Description : The thermal efficiency of an air/fuel gas preheating recuperator may be as high as __________ percent. (A) 50 (B) 65 (C) 85 (D) 99

Last Answer : (C) 85

. Thermal efficiency of an internal combustion engine is around __________ percent. (A) 8 (B) 35 (C) 65 (D) 80

Description : . Thermal efficiency of an internal combustion engine is around __________ percent. (A) 8 (B) 35 (C) 65 (D) 80

Last Answer : Option B

Abrasion index of blast furnace coke should be around __________ percent. (A) 20 (B) 35 (C) 55 (D) 80

Description : Abrasion index of blast furnace coke should be around __________ percent. (A) 20 (B) 35 (C) 55 (D) 80

Last Answer : (D) 80

Grinding efficiency of a ball mill is of the order of __________ percent. (A) 1-5 (B) 40-50 (C) 75-80 (D) 90-95

Description : Grinding efficiency of a ball mill is of the order of __________ percent. (A) 1-5 (B) 40-50 (C) 75-80 (D) 90-95

Last Answer : (A) 1-5

Which furnace employs preheating, heating and soaking zones? (A) Soaking pit (B) Reheating furnace (C) Open hearth furnace (D) Cupola

Description : Which furnace employs preheating, heating and soaking zones? (A) Soaking pit (B) Reheating furnace (C) Open hearth furnace (D) Cupola

Last Answer : (B) Reheating furnace

Regenerators are normally provided in the (A) Glass melting furnace (B) Open hearth furnace (C) By product coke ovens (D) All (A), (B) and (C)

Description : Regenerators are normally provided in the (A) Glass melting furnace (B) Open hearth furnace (C) By product coke ovens (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Regenerators are normally provided in the (A) Glass melting furnace (B) Open hearth furnace (C) By product coke ovens (D) All (A), (B) and (C)

Description : Regenerators are normally provided in the (A) Glass melting furnace (B) Open hearth furnace (C) By product coke ovens (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Regenerators are installed in (A) Coke ovens (B) Open hearth furnace (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Regenerators are installed in (A) Coke ovens (B) Open hearth furnace (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Which of the following is not a directly fired furnace? (A) By-product coke oven (B) Calcination kiln (C) Sintering furnace (D) Open hearth furnace

Description : Which of the following is not a directly fired furnace? (A) By-product coke oven (B) Calcination kiln (C) Sintering furnace (D) Open hearth furnace

Last Answer : (A) By-product coke oven

An example of recuperative furnace is the (A) Soaking pit (B) Open hearth furnace (C) Coke ovens (D) None of these

Description : An example of recuperative furnace is the (A) Soaking pit (B) Open hearth furnace (C) Coke ovens (D) None of these

Last Answer : (A) Soaking pit

Which is a regenerative furnace? (A) Coke oven heating chamber (B) Open hearth furnace (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Which is a regenerative furnace? (A) Coke oven heating chamber (B) Open hearth furnace (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Which is not a hearth furnace? (A) Glass tank furnace (B) Open hearth furnace (C) Cupola

Description : Which is not a hearth furnace? (A) Glass tank furnace (B) Open hearth furnace (C) Cupola

Last Answer : (C) Cupola

If the flame is produced under the hearth and then sweeps up into the heating chamber, this is called a/an __________ furnace. (A) Sidefired (B) Underfired (C) Covered (D) Recirculating

Description : If the flame is produced under the hearth and then sweeps up into the heating chamber, this is called a/an __________ furnace. (A) Sidefired (B) Underfired (C) Covered (D) Recirculating

Last Answer : (B) Underfired

An improved and fuel efficient version of the pusher type reheating furnace is the __________ furnace. (A) Walking beam (B) Shaft (C) Tunnel (D) Rotary hearth

Description : An improved and fuel efficient version of the pusher type reheating furnace is the __________ furnace. (A) Walking beam (B) Shaft (C) Tunnel (D) Rotary hearth

Last Answer : (A) Walking beam

Maximum thermal efficiency of boiler may be about __________ percent. (A) 10 (B) 25 (C) 65 (D) 90

Description : Maximum thermal efficiency of boiler may be about __________ percent. (A) 10 (B) 25 (C) 65 (D) 90

Last Answer : (D) 90

Pick up the correct statement from the following: (A) In basic Bessemer process, the steel heats the converter (B) In open-hearth process, the furnace heats the steel (C) In Siemens process, the impurities of pig iron are oxidised by the oxygen of the ore (D) All the above

Description : Pick up the correct statement from the following: (A) In basic Bessemer process, the steel heats the converter (B) In open-hearth process, the furnace heats the steel (C) In Siemens process, the impurities of pig iron are oxidised by the oxygen of the ore (D) All the above

Last Answer : Answer: Option D

Furnace oil consumption in a furnace for a given duty employing preheated combination air (at 300°) may be reduced by about __________ percent as compared to the use of atmospheric combustion air. (A) 5 (B) 10 (C) 20 (D) 35

Description : Furnace oil consumption in a furnace for a given duty employing preheated combination air (at 300°) may be reduced by about __________ percent as compared to the use of atmospheric combustion air. (A) 5 (B) 10 (C) 20 (D) 35

Last Answer : (C) 20

285. Sucrose content in the raw juice extracted from sugar cane is about __________ percent(A) 1 - 2 (B) 15 - 20 (C) 50 - 60 (D) 80 - 85

Description : . Sucrose content in the raw juice extracted from sugar cane is about __________ percent (B) 15 - 20 (A) 1 - 2285 (C) 50 - 60 (D) 80 - 85

Last Answer : (B) 15 - 20

Carbon Content by weight in air dried wood may be about __________ percent. (A) 10 (B) 25 (C) 50 (D) 80

Description : Carbon Content by weight in air dried wood may be about __________ percent. (A) 10 (B) 25 (C) 50 (D) 80

Last Answer : (C) 50

Sucrose content in cane sugar may be around __________ percent. (A) 50 (B) 70 (C) 95(D) 80

Description : Sucrose content in cane sugar may be around __________ percent. (A) 50 (B) 70 (C) 95 (D) 80

Last Answer : (C) 95

Large tonnage of refractory bricks are dried in a (A) Shaft furnace (B) Rotary hearth furnace (C) Tunnel kiln (D) Muffle furnace

Description : Large tonnage of refractory bricks are dried in a (A) Shaft furnace (B) Rotary hearth furnace (C) Tunnel kiln (D) Muffle furnace

Last Answer : (C) Tunnel kiln

Unit of furnace loading is (A) Ton stock/hr/m2 hearth area (B) Ton stock/hr (C) Ton stock/m2 hearth area (D) Both (B) and (C)

Description : Unit of furnace loading is (A) Ton stock/hr/m2 hearth area (B) Ton stock/hr (C) Ton stock/m2 hearth area (D) Both (B) and (C)

Last Answer : (A) Ton stock/hr/m2 hearth area

The heating capacity of continuous reheating furnace depends upon the (A) Hearth area and furnace temperature (B) Emissivity of the stock (C) Ratio of wall surface to stock surface (D) All (A), (B) and (C)

Description : The heating capacity of continuous reheating furnace depends upon the (A) Hearth area and furnace temperature (B) Emissivity of the stock (C) Ratio of wall surface to stock surface (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Thermal efficiency of an internal combustion engine is around __________ percent. (A) 8 (B) 35 (C) 65

Description : Thermal efficiency of an internal combustion engine is around __________ percent. (A) 8 (B) 35 (C) 65

Last Answer : Option B

Which of the following furnaces will have maximum thermal efficiency? (A) Soaking pits (B) Walking beam reheating furnace (C) Boiler furnace (D) Rotary kilns

Description : Which of the following furnaces will have maximum thermal efficiency? (A) Soaking pits (B) Walking beam reheating furnace (C) Boiler furnace (D) Rotary kilns

Last Answer : (C) Boiler furnace

Thermal efficiency of furnaces can be improved by (A) Waste heat recovery from flue gas (B) Minimising heat losses from furnace walls(C) Maintaining proper draught(D) All (A), (B) and (C

Description : Thermal efficiency of furnaces can be improved by (A) Waste heat recovery from flue gas (B) Minimising heat losses from furnace walls (C) Maintaining proper draught (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

Air filtration in a furnace (A) Reduces its thermal efficiency (B) Is indicated by flame sting out (C) Increases the flue gas temperature (D) None of these

Description : Air filtration in a furnace (A) Reduces its thermal efficiency (B) Is indicated by flame sting out (C) Increases the flue gas temperature (D) None of these

Last Answer : (A) Reduces its thermal efficiency

The heat recoverable from flue gases of furnaces depends on the (A) Thermal efficiency of furnace (B) Quantity of flue gases (C) Flue gas temperature drop through the furnace (D) All (A), (B) and (C)

Description : The heat recoverable from flue gases of furnaces depends on the (A) Thermal efficiency of furnace (B) Quantity of flue gases (C) Flue gas temperature drop through the furnace (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Heat balance of furnace provides means of determining the (A) Thermal efficiency of the process (B) Sources of heat losses (C) Scope of reduction of heat losses(D) All (A), (B) and (C)

Description : Heat balance of furnace provides means of determining the (A) Thermal efficiency of the process (B) Sources of heat losses (C) Scope of reduction of heat losses (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Description : Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

High relative humidity decreases the evaporative process and as the temperature is increased, the relative humidity decreases. The comfort range for human body is the ambient temperature of 22 to 27°C with relative humidity ranging from __________ percent. (A) 5 to 10 (B) 15 to 25 (C) 45 to 50 (D) 75 to 80

Description : High relative humidity decreases the evaporative process and as the temperature is increased, the relative humidity decreases. The comfort range for human body is the ambient temperature of 22 to 27°C with relative humidity ranging from __________ ... to 10 (B) 15 to 25 (C) 45 to 50 (D) 75 to 80

Last Answer : (C) 45 to 50

Softer variety of steel may be obtained by (A) Cementation process (B) Crucible process (C) Bessemer process (D) Open hearth

Description : Softer variety of steel may be obtained by (A) Cementation process (B) Crucible process (C) Bessemer process (D) Open hearth

Last Answer : Answer: Option C

Nitrogen content of calcium ammonium nitrate (CAN) is __________ percent. (A) 10 (B) 25 (C) 50 (D) 80

Description : Nitrogen content of calcium ammonium nitrate (CAN) is __________ percent. (A) 10 (B) 25 (C) 50 (D) 80

Last Answer : (B) 25

Cellulose content of bamboo and ideal fibrous raw material for the manufacture of paper is __________ percent. (A) 10 (B) 50 (C) 80 (D) 95

Description : Cellulose content of bamboo and ideal fibrous raw material for the manufacture of paper is __________ percent. (A) 10 (B) 50 (C) 80 (D) 95

Last Answer : (B) 50

Efficiency of power transmission (η) through a circular pipe is given by (ht - hf )/ht , which has a maximum value of __________ percent. (A) 33:3 (B) 50 (C) 66.6 (D) 88.8

Description : Efficiency of power transmission (η) through a circular pipe is given by (ht - hf )/ht , which has a maximum value of __________ percent. (A) 33:3 (B) 50 (C) 66.6 (D) 88.8

Last Answer : (C) 66.6

Alcohol content in freshly prepared natural and fortified **** may be respectively around __________ percent. (A) 7-14 and 14-30 (B) 7-14 and 40-50 (C) 14 - 30 and 40-50 (D) 10 - 20 and 40 - 50

Description : Alcohol content in freshly prepared natural and fortified wine may be respectively around __________ percent. (A) 7-14 and 14-30 (B) 7-14 and 40-50 (C) 14 - 30 and 40-50 (D) 10 - 20 and 40 - 50

Last Answer : (A) 7-14 and 14-30

Crushing efficiency of a machine ranges between __________ percent. (A) 0.1 to 2 (B) 5 to 10 (C) 20 to 25

Description : Crushing efficiency of a machine ranges between __________ percent. (A) 0.1 to 2 (B) 5 to 10 (C) 20 to 25

Last Answer : (A) 0.1 to 2

What is defined as the ratio of the net electrical power output to the rate of fuel energy input?  A. Combustion efficiency  B. Thermal efficiency  C. Overall efficiency  D. Furnace efficiency

Description : What is defined as the ratio of the net electrical power output to the rate of fuel energy input?  A. Combustion efficiency  B. Thermal efficiency  C. Overall efficiency  D. Furnace efficiency

Last Answer : Overall efficiency

Ringelmann chart No. 2 corresponds to __________ percent black smoke. (A) 10 (B) 20 (C) 40 (D) 80

Description : Ringelmann chart No. 2 corresponds to __________ percent black smoke. (A) 10 (B) 20 (C) 40 (D) 80

Last Answer : (C) 40

Equipment installation cost in a chemical process plant ranges from __________ percent of the purchased equipment cost. (A) 10 to 20 (B) 35 to 45 (C) 55 to 65 (D) 70 to 80

Description : Equipment installation cost in a chemical process plant ranges from __________ percent of the purchased equipment cost. (A) 10 to 20 (B) 35 to 45 (C) 55 to 65 (D) 70 to 80

Last Answer : (B) 35 to 45

Iron content in Indian iron ore is about __________ percent. (A) 80-85 (B) 60-65 (C) 40-45 (D) 20-25

Description : Iron content in Indian iron ore is about __________ percent. (A) 80-85 (B) 60-65 (C) 40-45 (D) 20-25

Last Answer : (B) 60-65

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

Percentage of nitrogen in blast furnace gas may be around (A) 5 (B) 25 (C) 55 (D) 80

Description : Percentage of nitrogen in blast furnace gas may be around (A) 5 (B) 25 (C) 55 (D) 80

Last Answer : (C) 55

A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of thermal conductivity 0.14 W/m.K and thickness __________ metre. (A) 0.01 (B) 0.1 (C) 0.25 (D) 0.5

Description : A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of ... and thickness __________ metre. (A) 0.01 (B) 0.1 (C) 0.25 (D) 0.5

Last Answer : (B) 0.1