Elimination of brittleness resulting from welding of saw blades is done by __________ of the welded portion. (A) Annealing (B) Toughening (C) Work hardening (D) Tempering

Elimination of brittleness resulting from welding of saw blades is done by __________ of the welded portion.
(A) Annealing
(B) Toughening
(C) Work hardening
(D) Tempering
by

1 Answer

Answer :

(A) Annealing
by

Related questions

Pick out the correct statement. (A) Hot worked materials are subjected to annealing to remove internal stresses (B) Annealing of steel hardens it slightly (C) Normalising of a material induces stresses (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness

Description : Pick out the correct statement. (A) Hot worked materials are subjected to annealing to remove internal stresses (B) Annealing of steel hardens it slightly (C) Normalising of a material induces stresses (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness

Last Answer : (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness Share

Spheroidising of a material is a/an __________ process. (A) Normalising (B) Annealing (C) Tempering (D) Hardening

Description : Spheroidising of a material is a/an __________ process. (A) Normalising (B) Annealing (C) Tempering (D) Hardening

Last Answer : (B) Annealing

Heating the Hypo-eutectoid steels to 30°C above the upper critical temperature line, soaking at that temperature and then cooling slowly to the room temperature to form a pearlite & ferrite structure is called (A) Tempering (B) Hardening (C) Annealing (D) Normalising

Description : Heating the Hypo-eutectoid steels to 30°C above the upper critical temperature line, soaking at that temperature and then cooling slowly to the room temperature to form a pearlite & ferrite structure is called (A) Tempering (B) Hardening (C) Annealing (D) Normalising

Last Answer : Option C

__________ of hard alloy and tool steel is done to make it easily machinable. (A) Case carburising (B) Tempering (C) Normalising (D) Annealing

Description : __________ of hard alloy and tool steel is done to make it easily machinable. (A) Case carburising (B) Tempering (C) Normalising (D) Annealing

Last Answer : (B) Tempering

Softening of hardened steel is done by its (A) Normalising (B) Tempering (C) Annealing (D) Carburising

Description : Softening of hardened steel is done by its (A) Normalising (B) Tempering (C) Annealing (D) Carburising

Last Answer : (B) Tempering

Post weld heat treatment is done by (A) Normalising (B) Stress relieving (C) Tempering (D) Solution annealing

Description : Post weld heat treatment is done by (A) Normalising (B) Stress relieving (C) Tempering (D) Solution annealing

Last Answer : (B) Stress relieving

Softening of hardened steel is done by its (A) Normalising (B) Tempering (C) Annealing (D) Carburising

Description : Softening of hardened steel is done by its (A) Normalising (B) Tempering (C) Annealing (D) Carburising

Last Answer : (A) Normalising

Sub zero treatment of steel is done to (A) Suppress martensite transformation (B) Enhance its working performance in sub zero atmosphere (C) Reduce the retained austenite in hardened steel (D) Induce temper brittleness after its hardening

Description : Sub zero treatment of steel is done to (A) Suppress martensite transformation (B) Enhance its working performance in sub zero atmosphere (C) Reduce the retained austenite in hardened steel (D) Induce temper brittleness after its hardening

Last Answer : Option C

Case hardening of a material is (A) Followed by tempering or carburising (B) Preceded by its tempering (C) Done to get a soft ductile interior with a very hard surface (D) Carried out to get extreme hardness in its core

Description : Case hardening of a material is (A) Followed by tempering or carburising (B) Preceded by its tempering (C) Done to get a soft ductile interior with a very hard surface (D) Carried out to get extreme hardness in its core

Last Answer : (D) Carried out to get extreme hardness in its core

Which of the following mainly decides the current to be employed is arc welding? (A) Electrode size (B) Plate thickness (C) Voltage across the arc (D) Welded portion length

Description : Which of the following mainly decides the current to be employed is arc welding? (A) Electrode size (B) Plate thickness (C) Voltage across the arc (D) Welded portion length

Last Answer : (A) Electrode size

__________ is not a case hardening process.(A) Carburising (B) Nitriding (C) Cyaniding (D) Annealing

Description : __________ is not a case hardening process. (A) Carburising (B) Nitriding (C) Cyaniding (D) Annealing

Last Answer : (D) Annealing

Globular form of cementite is formed during the __________ process. (A) Spheroidising (B) Hardening (C) Annealing (D) Normalising

Description : Globular form of cementite is formed during the __________ process. (A) Spheroidising (B) Hardening (C) Annealing (D) Normalising

Last Answer : (B) Hardening

The heat treatment process applied to cold formed steel parts is (A) Normalising (B) Tempering (C) Artificial ageing (D) Solution annealing

Description : The heat treatment process applied to cold formed steel parts is (A) Normalising (B) Tempering (C) Artificial ageing (D) Solution annealing

Last Answer : (D) Solution annealing

Which of the following heat treatment processes is used for softening the hardened material? (A) Normalising (B) Tempering (C) Annealing (D) None of these

Description : Which of the following heat treatment processes is used for softening the hardened material? (A) Normalising (B) Tempering (C) Annealing (D) None of these

Last Answer : (B) Tempering

The heat treatment process to which castings and the steel balls produced by cold heading are subjected is (A) Tempering (B) Normalising (C) Annealing (D) None of these

Description : The heat treatment process to which castings and the steel balls produced by cold heading are subjected is (A) Tempering (B) Normalising (C) Annealing (D) None of these

Last Answer : (B) Normalising

. To improve the machinability of steel, it is generally subjected to (A) Spheroidising (B) Tempering (C) Normalising (D) Annealing

Description : . To improve the machinability of steel, it is generally subjected to (A) Spheroidising (B) Tempering (C) Normalising (D) Annealing

Last Answer : (A) Spheroidising

Hardened steel is softened by (A) Normalising (B) Tempering (C) Annealing (D) Carburising

Description : Hardened steel is softened by (A) Normalising (B) Tempering (C) Annealing (D) Carburising

Last Answer : (B) Tempering

Which of the following heat treatment processes is usually applied to castings? (A) Tempering (B) Annealing (C) Normalising (D) Carburising

Description : Which of the following heat treatment processes is usually applied to castings? (A) Tempering (B) Annealing (C) Normalising (D) Carburising

Last Answer : (D) Carburising

Machinability of hard alloys and tool steels is improved by (A) Spheroidising (B) Annealing (C) Tempering (D) Normalising

Description : Machinability of hard alloys and tool steels is improved by (A) Spheroidising (B) Annealing (C) Tempering (D) Normalising

Last Answer : Option B

o improve the machinability of steel, it is generally subjected to (A) Spheroidising (B) Tempering (C) Normalising (D) Annealing

Description : o improve the machinability of steel, it is generally subjected to (A) Spheroidising (B) Tempering (C) Normalising (D) Annealing

Last Answer : Option A

Between 230 and 370°C, blue brittleness is caused in mild steel because of the (A) Immobility of dislocation (B) Strain-ageing (C) Increase in Young's modulus (D) Strain hardening

Description : Between 230 and 370°C, blue brittleness is caused in mild steel because of the (A) Immobility of dislocation (B) Strain-ageing (C) Increase in Young's modulus (D) Strain hardening

Last Answer : Option B

Which of the following processes follows the hardening process for reducing the hardening strains & increasing the toughness of the steel part? (A) Anodising (B) Tempering (C) Carburising

Description : Which of the following processes follows the hardening process for reducing the hardening strains & increasing the toughness of the steel part? (A) Anodising (B) Tempering (C) Carburising

Last Answer : (B) Tempering

Differentiate Hardening and Tempering of Automobile Parts.

Description : Differentiate Hardening and Tempering of Automobile Parts.

Last Answer : Differentiate Hardening and Tempering: Parameter Hardening Tempering Definition Hardening or quenching is the process of increasing the hardness of a material. Tempering is the process of ... a metal tempering is done to reduce the brittleness of quenched metal or alloy.

Cold worked steel parts are normally subjected to (A) Normalising (B) Hardening (C) Annealing (D) Shot peening

Description : Cold worked steel parts are normally subjected to (A) Normalising (B) Hardening (C) Annealing (D) Shot peening

Last Answer : (C) Annealing

Nitriding of steel is a process for (A) Case hardening (B) Spheroidising (C) Normalising (D) Annealing

Description : Nitriding of steel is a process for (A) Case hardening (B) Spheroidising (C) Normalising (D) Annealing

Last Answer : (A) Case hardening

The maximum thickness of the metal which can be welded using ultrasonic welding is __________ mm. (A) 0.5 (B) 3 (C) 10 (D) 25

Description : The maximum thickness of the metal which can be welded using ultrasonic welding is __________ mm. (A) 0.5 (B) 3 (C) 10 (D) 25

Last Answer : (B) 3

Chromium molybdenum steel cannot be welded using __________ welding. (A) Thermit (B) Electrical resistance (C) Oxy-acetylene (D) Any of these

Description : Chromium molybdenum steel cannot be welded using __________ welding. (A) Thermit (B) Electrical resistance (C) Oxy-acetylene (D) Any of these

Last Answer : Option B

Welded joint strength increases due to annealing by i. 6% ii. 10% iii. 14% iv. None

Description : Welded joint strength increases due to annealing by i. 6% ii. 10% iii. 14% iv. None

Last Answer : i. 6%

Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation (B) Cavitation may be caused due to boiling of liquid by decreasing the pressure resulting in formation & collapse of vapor cavities (C) Cavitation begins at higher static pressure and lower velocity in larger diameter pipelines resulting in audible noise(D) Large scale cavitation cannot damage pipeline, restrict fluid flow anddamage steam turbine blades

Description : Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation ... (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Last Answer : (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the tip diameter should be equal to t (where, t = plate thickness to be welded) (C) In spot welding, two pieces to be joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded

Description : Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the ... joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded

Last Answer : (D) Mild steel sheet cannot be spot welded

Stainless steel is welded using (A) Oxy-acetylene flame (B) Oxy-hydrogen flame (C) Arc welding (D) Inert gas arc welding

Description : Stainless steel is welded using (A) Oxy-acetylene flame (B) Oxy-hydrogen flame (C) Arc welding (D) Inert gas arc welding

Last Answer : (D) Inert gas arc welding

Oxygen cylinders used for autogenous (cutting/welding) purposes are (A) Seamless & made of steel (B) Heat treated before use (C) Made by sand casting (D) Welded steel cylinders

Description : Oxygen cylinders used for autogenous (cutting/welding) purposes are (A) Seamless & made of steel (B) Heat treated before use (C) Made by sand casting (D) Welded steel cylinders

Last Answer : Option A

Image P shows a portion of a larger photograph. Some operations have been done on that photograph using an image manipulation software. Image Q shows a portion of the resulting photograph. Identify the option(s) that specifies/specify the correct operations.

Description : Image P shows a portion of a larger photograph. Some operations have been done on that photograph using an image manipulation software. Image Q shows a portion of the resulting photograph. Identify ... D. Rotate clockwise by 90 degrees, flip horizontally, then rotate clockwise by 45 degrees 

Last Answer : A C

Rails in the field are generally welded by using a) Thermit welding b) Gas welding c) Electric arc welding d) Forge welding

Description : Rails in the field are generally welded by using a) Thermit welding b) Gas welding c) Electric arc welding d) Forge welding

Last Answer : a) Thermit welding

Pick up the incorrect statement (A) The cross-sectional area of the welded member is effective (B) A welded joint develops strength of its parent metal (C) Welded joints provide rigidity (D) Welding takes more time than riveting

Description : Pick up the incorrect statement (A) The cross-sectional area of the welded member is effective (B) A welded joint develops strength of its parent metal (C) Welded joints provide rigidity (D) Welding takes more time than riveting

Last Answer : (D) Welding takes more time than riveting

Rails used for A T Welding shall not normally be welded? (i) 20 years old . (ii) 30 years old (iii) 40 years old (iv) 50 years old*

Description : Rails used for A T Welding shall not normally be welded? (i) 20 years old . (ii) 30 years old (iii) 40 years old (iv) 50 years old*

Last Answer : iv) 50 years old*

How often should circular saw blades be changed?

Description : How often should circular saw blades be changed?

Last Answer : Turn off all power to the circular saw and remove the power cord from the wall outlet. Twist tie or tie off the cord to keep it out of the way while changing the blade,Slide up the protective blade ... aside. Remove the saw blade and place the new blade in its place. Replace the blade bolt and tigh

Can saw blades be sharpened and how?

Description : Can saw blades be sharpened and how?

Last Answer : They can be sharpened with special files but it's best to get someone to do it for you.

Tempering of steel is done to make it (A) Brittle (B) Hard (C) Rollable (D) Soft

Description : Tempering of steel is done to make it (A) Brittle (B) Hard (C) Rollable (D) Soft

Last Answer : (D) Soft

Tempering of steel is done to make it (A) Brittle (B) Hard (C) Rollable (D) Soft

Description : Tempering of steel is done to make it (A) Brittle (B) Hard (C) Rollable (D) Soft

Last Answer : (D) Soft

Cross linked polymers formed from bi-and trifunctional groups in which cross-linkage in three dimensions via few chemical bonding across linear chains occur imparts to the polymer __________ properties. (A) Thermoplastic (B) Thermosetting (C) Elastometric (D) Brittleness

Description : Cross linked polymers formed from bi-and trifunctional groups in which cross-linkage in three dimensions via few chemical bonding across linear chains occur imparts to the polymer __________ properties. (A) Thermoplastic (B) Thermosetting (C) Elastometric (D) Brittleness

Last Answer : (C) Elastometric

__________ are added in lacquers to remove film brittleness and to improve adhereness. (A) Film forming materials (B) Plasticisers (C) Diluents (D) Solvents

Description : __________ are added in lacquers to remove film brittleness and to improve adhereness. (A) Film forming materials (B) Plasticisers (C) Diluents (D) Solvents

Last Answer : (B) Plasticisers

Temper brittleness of a material can be fairly detected by the __________ test. (A) Fatigue (B) Notched bar impact (C) Tensile (D) Hardness

Description : Temper brittleness of a material can be fairly detected by the __________ test. (A) Fatigue (B) Notched bar impact (C) Tensile (D) Hardness

Last Answer : Option B

__________ of grey cast iron produces white cast iron. (A) Tempering (B) Rapid heating (C) Rapid cooling (D) Slow cooling

Description : __________ of grey cast iron produces white cast iron. (A) Tempering (B) Rapid heating (C) Rapid cooling (D) Slow cooling

Last Answer : Option B

In AT welding process what is the role of asbestos powder & slag ? (i) To separate closing pin from portion* (ii) To hold the portion (iii) Both above are correct (iv) None of the above

Description : In AT welding process what is the role of asbestos powder & slag ? (i) To separate closing pin from portion* (ii) To hold the portion (iii) Both above are correct (iv) None of the above

Last Answer : (i) To separate closing pin from portion*

In AT welding process what is the role of closing pin ? (i) To hold the portion before melt (ii) To hold the asbestos powder & slag (iii) Both above are correct* (iv) None of the above

Description : In AT welding process what is the role of closing pin ? (i) To hold the portion before melt (ii) To hold the asbestos powder & slag (iii) Both above are correct* (iv) None of the above

Last Answer : (iii) Both above are correct*

Where Portion sample tests(test piece) should be conducted? (i) At desire by RDSO (ii) At Zonal CMT’s organisation or the Flash Butt Welding plant. * (iii) In RDSO campus (iv) As decided by in charge of the plant

Description : Where Portion sample tests(test piece) should be conducted? (i) At desire by RDSO (ii) At Zonal CMT’s organisation or the Flash Butt Welding plant. * (iii) In RDSO campus (iv) As decided by in charge of the plant

Last Answer : At Zonal CMT’s organisation or the Flash Butt Welding plant.

How rejected portion are to be disposed-off? (i) By Igniting 5 Portions at a time in pit away from store?* (ii) By throwing them away (iii) By dispose off in a pit (iv) By using it in Branch/Yard lines for welding

Description : How rejected portion are to be disposed-off? (i) By Igniting 5 Portions at a time in pit away from store?* (ii) By throwing them away (iii) By dispose off in a pit (iv) By using it in Branch/Yard lines for welding

Last Answer : (i) By Igniting 5 Portions at a time in pit away from store?*