Description : Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30
Last Answer : (B) 25
Description : Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the ... joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded
Last Answer : (D) Mild steel sheet cannot be spot welded
Description : Which of the following mainly decides the current to be employed is arc welding? (A) Electrode size (B) Plate thickness (C) Voltage across the arc (D) Welded portion length
Last Answer : (A) Electrode size
Description : The frame consists of a steel beam welded rigidly to two vertical channels. An eccentric exciter weighing 250 N is attached to the beam, which weighs 10 KN and is used to excite the frame. The unbalance weight of ... ends, magnification factor at resonance is A. 307.5 B. 3.075 C. 30.75 D. 0.3075
Last Answer : C. 30.75
Description : Chromium molybdenum steel cannot be welded using __________ welding. (A) Thermit (B) Electrical resistance (C) Oxy-acetylene (D) Any of these
Last Answer : Option B
Description : Which of the following are considered applications of ultrasonic testing? (A) Determination of elastic constant (B) Detection of defects in metal (C) Measurement of material thickness (D) None of the above
Last Answer : (B) Detection of defects in metal
Description : Pick up the incorrect statement (A) The cross-sectional area of the welded member is effective (B) A welded joint develops strength of its parent metal (C) Welded joints provide rigidity (D) Welding takes more time than riveting
Last Answer : (D) Welding takes more time than riveting
Description : Elimination of brittleness resulting from welding of saw blades is done by __________ of the welded portion. (A) Annealing (B) Toughening (C) Work hardening (D) Tempering
Last Answer : (A) Annealing
Description : Stainless steel is welded using (A) Oxy-acetylene flame (B) Oxy-hydrogen flame (C) Arc welding (D) Inert gas arc welding
Last Answer : (D) Inert gas arc welding
Description : The maximum thickness of expansion joint in rigid pavements is (A) 0 (B) 25 mm (C) 50 mm (D) 100 mm
Last Answer : Answer: Option B
Description : Rails in the field are generally welded by using a) Thermit welding b) Gas welding c) Electric arc welding d) Forge welding
Last Answer : a) Thermit welding
Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the ... , is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm
Last Answer : (C) 20 mm
Description : Ratings for welding neck flanges under ASME B16.5 are based upon which of the following? a) The flange thickness and 40,000 psi yield strength. b) The hub thickness at the welding end and ... psi yield strength. c) The weld metal yield strength. d) The piping wall thickness and yield strength.
Last Answer : b) The hub thickness at the welding end and 40,000 psi yield strength
Description : Oxygen cylinders used for autogenous (cutting/welding) purposes are (A) Seamless & made of steel (B) Heat treated before use (C) Made by sand casting (D) Welded steel cylinders
Last Answer : Option A
Description : What is the minimum thickness of hub at the welding end per ASME B16.5? a) The numeral pipe thickness. b) 87 ½% of the pipe thickness. c) 112 ½% of the pipe thickness. d) .25".
Last Answer : b) 87 ½% of the pipe thickness.
Description : Pick out the wrong statement. (A) For a pressure vessel to be classified as 'thin vessel', the ratio of wall thickness to mean radius is less than 0.1 (B) For calculating forces and ... Maximum diameter of the opening provided in a pressure vessel, which does not require any compensation is 200 mm
Description : For determining the ultimate bearing capacity of soil, the recommended size of a square bearing plate to be used in load plate test should be 30 to 75 cm square with a minimum thickness of (A) 5 mm (B) 10 mm (C) 15 mm (D) 25 mm
Last Answer : Answer: Option D
Description : The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm
Description : Rails used for A T Welding shall not normally be welded? (i) 20 years old . (ii) 30 years old (iii) 40 years old (iv) 50 years old*
Last Answer : iv) 50 years old*
Description : Double full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 3/8” iii. 5/8” iv. None
Last Answer : iii. 5/8”
Description : How do ultrasonic thickness gauges work?
Last Answer : I found a few sites on the web that can help you this and finding out about this. Here are the sites you can look at www.olympus-ims.com/...ultrasonics/introduction-thickness-g
Description : Which type of ultrasonic thickness gauge would be best suited for our project?
Last Answer : An ultrasonic thickness gauge is required for measuring the thickness of different types of materials. The best ultrasonic thickness gauge you can buy is the Defelsko Corporation Ultrasonic Thickness gauge.
Description : Single full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 2/8” iii. 3/8” iv. None
Last Answer : iii. 3/8”
Description : The minimal labial tooth reduction for satisfactory aesthetics with porcelain fused to metal crown is, A. 1mm B. The full thickness of enamel C. 1.5 mm D. 2.5mm E. One third of the dentine thickness
Last Answer : C. 1.5 mm
Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm
Last Answer : d) 2.0 kJ/mm
Description : The thickness of bituminous carpet varies from (A) 20 to 25 mm (B) 50 to 75 mm (C) 75 to 100 mm (D) 100 to 120 mm
Last Answer : Answer: Option A
Description : Thickness of Lining/Charge is kept? (i) 20 mm. (ii) 25 mm* (iii) 30 mm (iv) As decided by the site supervisor
Last Answer : (ii) 25 mm*
Description : As per IRCA rules, the rejection limits for wheel flange thickness is - (a) 38mm (b) 25.4mm (c) 16mm* (d) 20 mm
Last Answer : (c) 16mm*
Description : A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of ... and thickness __________ metre. (A) 0.01 (B) 0.1 (C) 0.25 (D) 0.5
Last Answer : (B) 0.1
Description : For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate
Last Answer : (a) 1.5 mm less than the plate thickness
Description : Steel is welded using the __________ flame. (A) Carburising (B) Neutral (C) Oxidising (D) All (A), (B) & (C)
Description : The maximum of spacing of side face reinforcement shall not exceed [ A ] 300 mm [ B ] Web thickness [ C ] Lesser of (a) and (b) [ D ] Greater of (a) and (b)
Last Answer : [ C ] Lesser of (a) and (b)
Description : A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm
Last Answer : b) 2.5cm
Description : Titanium metal (A) Exists in three allotropic forms (B) Cannot be welded (C) Is used in oceanographic and space exploration applications (D) None of these
Last Answer : (C) Is used in oceanographic and space exploration applications
Description : After AT Welding First train is to be passed after ? (i) 20 Minutes from pouring of weld metal. (ii) 35 Minutes from pouring of weld metal. (iii) 30 Minutes from pouring of weld metal.* (iv) 25 Minutes from pouring of weld metal.
Last Answer : (iii) 30 Minutes from pouring of weld metal.*
Description : In new Rail as well as second hand rails how much end bends of the rails in lateral direction are permitted when checked with one metre straight edge before welding? (i) ± 0.2 mm in lateral direction (ii) ± 0.3 mm in lateral direction (iii) ± 0.5 mm in latera
Last Answer : (iii) ± 0.5 mm in latera
Description : In new Rail as well as second hand rails how much end bends of the rails in vertical are permitted when checked with one meter straight edge before welding? (i) +0.5mm, -0 mm in vertical * (ii) +0.2mm, -.3 mm in vertical (iii) +0.3mm, -2 mm in vertical (iv) 0 mm, +.5 mm in vertical
Last Answer : (i) +0.5mm, -0 mm in vertical *
Description : In welded wire mesh, the longitudinal wire is placed at (A) 10 cm centres (B) 15 cm centres (C) 20 cm centres (D) 25 cm centres
Description : Raw Kerosene has a smoke point of 15 mm. After it is subjected to dearomatization by liquid SO2 extraction (Edeleanu process), its smoke point may become __________ mm. (A) 5 (B) 10 (C) 25 (D) 100
Last Answer : (C) 25
Description : The maximum thickness of concrete floor of a cement warehouse, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm
Last Answer : (D) 25 cm
Description : Smoke point of a good burning kerosene may be around __________ mm. (A) 0-5 (B) 20-25 (C) 60-75 (D) 100-120
Last Answer : (B) 20-25
Description : Vibrating screens have capacity in the range of __________ tons/ft 2 .mm mesh size. (A) 0.2 to 0.8 (B) 5 to 25 (C) 50 to 100 (D) 100 to 250
Last Answer : (A) 0.2 to 0.8
Description : Thickness of plate is required more in welding than in riveting. a) True b) False
Last Answer : b) False
Description : When welding medium carbon steel plates over 100mm in thickness would the basic electrodes require any pre treatment before use? a) None if they were in a vacuum pack opened 8 hours prior to use b) None if ... ) Heat to 500 °C for 2 hours if used outside d) Baked at 150°C for 4hours prior to use
Last Answer : b) None if they were in a sealed vacuum pack prior to use
Description : If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm
Last Answer : Answer: Option C
Description : The nominal thickness of an expansion joint in brick walls, is kept more than (A) 5 mm (B) 10 mm (C) 15 mm (D) 20 mm
Description : Size of blast furnace grade coke is __________ mm. (A) 25-80 (B) 0-15 (C) 15-25 (D) > 100
Last Answer : (A) 25-80
Description : A loudspeaker cabinet has an internal volume of 5,184 in3 (84,950 cm3 ). It has a port area on the baffle of 50 in2 (322.58cm2 ) and a thickness of 0.70 in (18 mm). What is the Helmholtz resonance, in hertz, of this loudspeaker enclosure? A. 250 Hz B. 245 Hz C. 240 Hz D. 255 Hz
Last Answer : C. 240 Hz
Description : The thickness of metallic shielding on cables is usually (a) 0.04 mm (b) 0.2 to 0.4 mm (e) 3 to 5 mm (d) 40 to 60 mm
Last Answer : (a) 0.04 mm
Description : A practical formula for determining the thickness of insulation between low voltage and high voltage windings is (a) 1 + 0.2 kVmm (6) 2 + 0.5 kVmm (c) 4 + 0.7 kV mm (d) 5 + 0.9 kV mm
Last Answer : (d) 5 + 0.9 kV mm