Cross linked polymers formed from bi-and trifunctional groups in which cross-linkage in three dimensions via few chemical bonding across linear chains occur imparts to the polymer __________ properties. (A) Thermoplastic (B) Thermosetting (C) Elastometric (D) Brittleness

Cross linked polymers formed from bi-and trifunctional groups in which
cross-linkage in three dimensions via few chemical bonding across linear
chains occur imparts to the polymer __________ properties.
(A) Thermoplastic
(B) Thermosetting
(C) Elastometric
(D) Brittleness
by

1 Answer

Answer :

(C) Elastometric
by

Related questions

Pick out the wrong statement. (A) Linear polymers are formed from bifunctional groups only and are normally thermoplastic (B) Cross-linked branched chain polymers are either elastometric or thermosetting (C) Branching in case of cross-linked polymers caused by small amount of impurities in bifunctional monomer formulation reduces its solubility and increases the softening point (D) Dibasic acids reacts with dihydric alcohols to give polyesters using addition polymerisation reaction

Description : Pick out the wrong statement. (A) Linear polymers are formed from bifunctional groups only and are normally thermoplastic (B) Cross-linked branched chain polymers are either elastometric or ... (D) Dibasic acids reacts with dihydric alcohols to give polyesters using addition polymerisation reaction

Last Answer : D) Dibasic acids reacts with dihydric alcohols to give polyesters using addition polymerisation reaction

. In a linear polymer, the monomeric units are linked together to form long straight chains. The cross linked or branched chain polymers compared to linear polymers have higher (A) Densities (B) Melting point (C) Tensile strength (D) Hardness, rigidity & brittleness

Description : . In a linear polymer, the monomeric units are linked together to form long straight chains. The cross linked or branched chain polymers compared to linear polymers have higher (A) Densities (B) Melting point (C) Tensile strength (D) Hardness, rigidity & brittleness

Last Answer : (D) Hardness, rigidity & brittleness

Linear polymers are normally (A) Thermosetting (B) Thermoplastic (C) Elastometric (D) Having extremely high softening poin

Description : Linear polymers are normally (A) Thermosetting (B) Thermoplastic (C) Elastometric (D) Having extremely high softening poin

Last Answer : (B) Thermoplastic

Cross linked polymers are (A) Thermoplastic (B) Thermosetting (C) Either (A) or (B) (D) Fibres only

Description : Cross linked polymers are (A) Thermoplastic (B) Thermosetting (C) Either (A) or (B) (D) Fibres only

Last Answer : (B) Thermosetting

Thermosetting polymers as compared to thermoplastic polymers (A) Are formed by addition polymerisation (B) Have three dimensional structure (C) Have linear structure (D) None of these

Description : Thermosetting polymers as compared to thermoplastic polymers (A) Are formed by addition polymerisation (B) Have three dimensional structure (C) Have linear structure (D) None of these

Last Answer : (B) Have three dimensional structure

Polymethyl methacrylate (PMMA) which is also known as Perspex and is produced by bulk polymerisation of methyl methacrylate is not a __________ polymer. (A) Thermoplastic (B) Thermosetting (C) Linear (D) Glass like transparent

Description : Polymethyl methacrylate (PMMA) which is also known as Perspex and is produced by bulk polymerisation of methyl methacrylate is not a __________ polymer. (A) Thermoplastic (B) Thermosetting (C) Linear (D) Glass like transparent

Last Answer : (B) Thermosetting

Thermosetting resins/polymers as compared to thermoplastic ones are (A) Soluble in all organic solvents (B) More brittle (C) Formed by addition polymerisation only (D) Easily reshaped & reused

Description : Thermosetting resins/polymers as compared to thermoplastic ones are (A) Soluble in all organic solvents (B) More brittle (C) Formed by addition polymerisation only (D) Easily reshaped & reused

Last Answer : (B) More brittle

Polymers are classified into four categories namely thermosetting, thermoplastic, elastomer and fibre depending upon their (A) Molecular sizes (B) Magnitude of intermolecular forces (C) Resistance to heat (D) Polymerisation mechanism

Description : Polymers are classified into four categories namely thermosetting, thermoplastic, elastomer and fibre depending upon their (A) Molecular sizes (B) Magnitude of intermolecular forces (C) Resistance to heat (D) Polymerisation mechanism

Last Answer : (B) Magnitude of intermolecular forces

While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Description : While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Last Answer : A) Low impact strength

. Polymers which soften on heating and harden when cooled are (a) Cross-linked polymers (b) Copolymers (c) Thermosetting polymers (d) Thermoplastics

Description : Polymers which soften on heating and harden when cooled are (a) Cross-linked polymers (b) Copolymers (c) Thermosetting polymers (d) Thermoplastics

Last Answer : Thermoplastics

Differentiate between Thermoplastic and Thermosetting polymers.

Description : Differentiate between Thermoplastic and Thermosetting polymers.

Last Answer : Differentiate between Thermosetting and Thermoplastic polymers: Thermosetting Thermoplastic Polymers which once mould /shaped do not soften when heated and thus cannot be reshaped  Polymers whose ... tri, tetra or poly functional. Monomer used in this polymer bi functional.

Polycondensation reaction of polymerisation (A) Does not produce linear polymers (B) Produces only thermoplastic material (C) Produces epoxy polymers (D) Does not need any catalyst

Description : Polycondensation reaction of polymerisation (A) Does not produce linear polymers (B) Produces only thermoplastic material (C) Produces epoxy polymers (D) Does not need any catalyst

Last Answer : (C) Produces epoxy polymers

What is elasticity in polymers generally related to amount of hydrogen bonding between different subunits number of subunits in the polymer chain its greater tensile strength the synthetic composure?

Description : What is elasticity in polymers generally related to amount of hydrogen bonding between different subunits number of subunits in the polymer chain its greater tensile strength the synthetic composure?

Last Answer : amount of hydrogen bonding between different subunitsnumber of subunits in the polymer chainits greater tensile strengththe synthetic composure

Thermosetting resins are those polymers, which (A) Do not increase in plasticity with rise in temperature (B) Allow slip to occur between molecules (C) Do not take on a permanent set (D) None of theseThermosetting resins are those polymers, which(A) Do not increase in plasticity with rise in temperature(B) Allow slip to occur between molecules(C) Do not take on a permanent set(D) None of these

Description : Thermosetting resins are those polymers, which (A) Do not increase in plasticity with rise in temperature (B) Allow slip to occur between molecules (C) Do not take on a permanent set (D) None of these

Last Answer : (A) Do not increase in plasticity with rise in temperature

Poly Vinyl chloride (PVC) is a __________ material. (A) Thermoplastic (B) Thermosetting (C) Fibrous (D) Chemically active

Description : Poly Vinyl chloride (PVC) is a __________ material. (A) Thermoplastic (B) Thermosetting (C) Fibrous (D) Chemically active

Last Answer : (A) Thermoplastic

Poly Vinyl Chloride (P.V.C.) is a __________ material. (A) Thermosetting (B) Thermoplastic (C) Fibrous (D) Chemically active

Description : Poly Vinyl Chloride (P.V.C.) is a __________ material. (A) Thermosetting (B) Thermoplastic (C) Fibrous (D) Chemically active

Last Answer : (B) Thermoplastic

List any four properties of thermosetting polymers.

Description : List any four properties of thermosetting polymers.

Last Answer : Properties of thermosetting polymers:  1.Very poor elasticity 2.sronger attractive forces between chains 3. not soluble in organic compounds 4.can not be remoulded 5. these polymers produces by condensation polymerization

Thermosetting materials (A) Are cross-linked molecules (B) Soften on application of heat (C) Are solvent soluble (D) None of these

Description : Thermosetting materials (A) Are cross-linked molecules (B) Soften on application of heat (C) Are solvent soluble (D) None of these

Last Answer : (A) Are cross-linked molecules

Thermosetting materials (A) Are cross-linked molecules (B) Soften on application of heat (C) Are solvent soluble (D) None of these

Description : Thermosetting materials (A) Are cross-linked molecules (B) Soften on application of heat (C) Are solvent soluble (D) None of these

Last Answer : (A) Are cross-linked molecules

All thermoplastic, thermosetting & elastic materials can be processed in a extrusion machine, however it cannot be used for the production of plastic (A) Filaments (B) Pipes (C) Buckets (D) Tubings

Description : All thermoplastic, thermosetting & elastic materials can be processed in a extrusion machine, however it cannot be used for the production of plastic (A) Filaments (B) Pipes (C) Buckets (D) Tubings

Last Answer : (C) Buckets

Thermoplastic resins usually(A) Remain hard as long as they are hot(B) Cannot be reclaimed from waste(C) Permanent setting resins(D) Less brittle than thermosetting resins

Description : Thermoplastic resins usually (A) Remain hard as long as they are hot (B) Cannot be reclaimed from waste (C) Permanent setting resins (D) Less brittle than thermosetting resins

Last Answer : (D) Less brittle than thermosetting resins

Fibre reinforced plastic (FRP) are (A) Made of glass fibre and thermoplastic resins (B) Anisotropic (C) Made of thermosetting resin and glass fibre (D) Both 'b' & 'c'

Description : Fibre reinforced plastic (FRP) are (A) Made of glass fibre and thermoplastic resins (B) Anisotropic (C) Made of thermosetting resin and glass fibre (D) Both 'b' & 'c'

Last Answer : Option D

Pick out the wrong statement. (A) Copper is the metal having the highest electronic conductivity (B) Hardenability & Weldability of metals are inversely related (C) Covalent bonding formed by sharing of electrons is present in all semiconductor materials (D) Glass transition temperature applies to 'polymers' but not to 'glasses'

Description : Pick out the wrong statement. (A) Copper is the metal having the highest electronic conductivity (B) Hardenability & Weldability of metals are inversely related (C) Covalent bonding formed by ... all semiconductor materials (D) Glass transition temperature applies to 'polymers' but not to 'glasses'

Last Answer : Option A

__________ polymer is used for making unbreakable crockery. (A) Thermoplastic (B) Melamine (C) Addition (D) None of these

Description : __________ polymer is used for making unbreakable crockery. (A) Thermoplastic (B) Melamine (C) Addition (D) None of these

Last Answer : (B) Melamine

In a cross linked polymer, the monomeric units are linked together to constitute a three dimensional network. Which of the following is a cross￾linked polymer? (A) Bakelite (phenol formaldehyde) (B) Polyester (C) Polythene (D) Nylon-6

Description : In a cross linked polymer, the monomeric units are linked together to constitute a three dimensional network. Which of the following is a cross￾linked polymer? (A) Bakelite (phenol formaldehyde) (B) Polyester (C) Polythene (D) Nylon-6

Last Answer : (A) Bakelite (phenol formaldehyde)

Pick out the wrong statement regarding the solubility characteristics of high polymers. (A) Greater the degree of cross-linking in the polymer, lesser is its solubility (B) Polymers having more aliphatic character are more soluble in aliphatic solvents, while those polymers having more aromatic character are more soluble in aromatic solvents (C) Swelling tendency or solubility of polymers in a particular solvent decreases with increase in molecular weight of the solvent (D) High molecular weight polymers on dissolving gives solution of very low viscosity

Description : Pick out the wrong statement regarding the solubility characteristics of high polymers. (A) Greater the degree of cross-linking in the polymer, lesser is its solubility (B) Polymers having more ... of the solvent (D) High molecular weight polymers on dissolving gives solution of very low viscosity

Last Answer : (D) High molecular weight polymers on dissolving gives solution of very low viscosity

__________ is a thermosetting plastic. (A) Polythene (B) Epoxy polymer (C) P.V.C. (D) Polystyrene

Description : __________ is a thermosetting plastic. (A) Polythene (B) Epoxy polymer (C) P.V.C. (D) Polystyrene

Last Answer : (B) Epoxy polymer

The material which can be deformed permanently by heat and pressure is called a (1) thermoset (2) thermoplastic (3) chemical compound (4) polymer

Description : The material which can be deformed permanently by heat and pressure is called a (1) thermoset (2) thermoplastic (3) chemical compound (4) polymer

Last Answer : (1) thermoset Explanation: A thermosetting polymer, resin, or plastic, often called a thermoset, is a polymer that is irreversibly hardened by curing from a soft solid or viscous liquid prepolymer or resin.

The material which can be deformed permanently by heat and pressure is called a: (1) Thermoplastic (2) Thermoset (3) Chemical compound (4) Polymer

Description : The material which can be deformed permanently by heat and pressure is called a: (1) Thermoplastic (2) Thermoset (3) Chemical compound (4) Polymer

Last Answer : (2) Thermoset Explanation: Thermoset materials are those materials that are made by polymers joined together by chemical bonds, acquiring a highly cross linked polymer structure. They cannot melt.

Compare between thermoplastic and thermosetting plastic.

Description : Compare between thermoplastic and thermosetting plastic.

Last Answer : Thermoplastics Thermosetting They can be repeated softened by heat and hardened on cooling Once hardened and set they do not softened with application of heat They are formed by ... to soft under heat  They can be used at comparatively higher temperature without damage. 

__________ polythene is most prone to stress-cracking (A) High density (B) Low density (C) Cross-linked (D) Linear low density

Description : __________ polythene is most prone to stress-cracking (A) High density (B) Low density (C) Cross-linked (D) Linear low density

Last Answer : (A) High density

Pick out the wrong statement. (A) Polymeric fibres are never produced by addition polymerisation (B) Property of tackiness is exhibited by uncured rubber (C) Sharp melting point is not observed in thermoplastic polymers (D) Polythene generally has an excellent resistance to ultra violet rays

Description : Pick out the wrong statement. (A) Polymeric fibres are never produced by addition polymerisation (B) Property of tackiness is exhibited by uncured rubber (C) Sharp melting point is not observed in thermoplastic polymers (D) Polythene generally has an excellent resistance to ultra violet rays

Last Answer : (A) Polymeric fibres are never produced by addition polymerisation

Thermoplastic resins are those polymers, which (A) Has decreased plasticity at increasing temperature (B) Cannot be moulded (C) Easily deform under pressure at high temperature (D) None of these

Description : Thermoplastic resins are those polymers, which (A) Has decreased plasticity at increasing temperature (B) Cannot be moulded (C) Easily deform under pressure at high temperature (D) None of these

Last Answer : (C) Easily deform under pressure at high temperature

Which of the following types of polymers has the strongest inter particle forces? (A) Elastomers (B) Fibres (C) Thermoplastics (D) Thermosetting polymers

Description : Which of the following types of polymers has the strongest inter particle forces? (A) Elastomers (B) Fibres (C) Thermoplastics (D) Thermosetting polymers

Last Answer : (D) Thermosetting polymers

Thermosetting polymers are (A) Injection moulded (B) Cast molded (C) Extruded (D) None of these

Description : Thermosetting polymers are (A) Injection moulded (B) Cast molded (C) Extruded (D) None of these

Last Answer : (B) Cast molded

What is the purpose of plasticizers? (a) Harden plastics (b) Soften plastics (c) Initiate polymerizations (d) Cross-link polymer chains

Description : What is the purpose of plasticizers? (a) Harden plastics (b) Soften plastics (c) Initiate polymerizations (d) Cross-link polymer chains

Last Answer : Soften plastics

Vulcanization is the process of cross-linking polymer chains in rubber using (a) Sulfur. (b) Formaldehye. (c) Benzoyl peroxide. (d) Ethylene glycol.

Description : Vulcanization is the process of cross-linking polymer chains in rubber using (a) Sulfur. (b) Formaldehye. (c) Benzoyl peroxide. (d) Ethylene glycol.

Last Answer : Sulfur.

In case of wet spinning of polymers, the polymer solution is forced through spinnerates into, a coagulating bath to give a filament form. Wet spinning is not used in case of the __________ fibres. (A) Viscose rayon (B) Acrylic (C) Polyvinyl acetate (D) Saturated polyeste

Description : In case of wet spinning of polymers, the polymer solution is forced through spinnerates into, a coagulating bath to give a filament form. Wet spinning is not used in case of the __________ fibres. (A) Viscose rayon (B) Acrylic (C) Polyvinyl acetate (D) Saturated polyeste

Last Answer : (D) Saturated polyeste

Melt spinning of polymers involves the forcing of polymer melt through spinnerates (fine holes) into an atmosphere kept at a temperature lower than the melting point of the polymer, which causes the fine diameter polymer melt to harden into filaments. Melt spinning is not used in case of the __________ fibres. (A) Acrylic (B) Polyester (C) Nylon 6:6 (D) Polypropylene

Description : Melt spinning of polymers involves the forcing of polymer melt through spinnerates (fine holes) into an atmosphere kept at a temperature lower than the melting point of the polymer, which causes the fine diameter ... the __________ fibres. (A) Acrylic (B) Polyester (C) Nylon 6:6 (D) Polypropylene

Last Answer : (A) Acrylic

In case of dry spinning of polymers, the polymer solution in a volatile solvent is forced through the spinnerates into a warm air chamber, where the solvent evaporates leaving behind the polymer in the filament form. Dry spinning is used for __________ fibres. (A) Polythene (B) PVC (C) Rayon (D) Polyvinyl acetate

Description : In case of dry spinning of polymers, the polymer solution in a volatile solvent is forced through the spinnerates into a warm air chamber, where the solvent evaporates leaving behind the polymer in the filament ... is used for __________ fibres. (A) Polythene (B) PVC (C) Rayon (D) Polyvinyl acetate

Last Answer : (B) PVC

Distinguish between thermoplastic and thermo setting polymers.

Description : Distinguish between thermoplastic and thermo setting polymers.

Last Answer : Thermo plastic polymer Thermo setting plastic  1. The inter moliculer forces are intermediate.  1. The inter molecular force are ... 3. Eg. Polythene and polystyrene  3. Eg. Bakelite

Silicone is a/an (A) Monomer (B) Inorganic polymer (C) Thermoplastic material (D) A natural polymer

Description : Silicone is a/an (A) Monomer (B) Inorganic polymer (C) Thermoplastic material (D) A natural polymer

Last Answer : (B) Inorganic polymer

Pick out the wrong statement. (A) Polystyrene is a thermoplastic polymer (B) Protein is a natural polymer (C) Neoprene is a natural rubber (D) Polythene is a copolymer, while SBR is a homopolymer

Description : Pick out the wrong statement. (A) Polystyrene is a thermoplastic polymer (B) Protein is a natural polymer (C) Neoprene is a natural rubber (D) Polythene is a copolymer, while SBR is a homopolymer

Last Answer : (C) Neoprene is a natural rubber

Bakelite is a/an (A) Addition polymer (B) Elastomer (C) Thermoplastic (D) None of these

Description : Bakelite is a/an (A) Addition polymer (B) Elastomer (C) Thermoplastic (D) None of these

Last Answer : (D) None of these

Which of the following is not a thermoplastic material? (A) Epoxy polymer (B) PVC (C) Polystyrene (D) Polythene

Description : Which of the following is not a thermoplastic material? (A) Epoxy polymer (B) PVC (C) Polystyrene (D) Polythene

Last Answer : (A) Epoxy polymer

Silicone is a/an (A) Thermoplastic (B) Inorganic polymer (C) Monomer (D) None of these

Description : Silicone is a/an (A) Thermoplastic (B) Inorganic polymer (C) Monomer (D) None of these

Last Answer : (B) Inorganic polymer

Addition of tungsten to steel imparts (A) Magnetic properties (B) Cutting hardness (C) Corrosion resistance (D) Ductility

Description : Addition of tungsten to steel imparts (A) Magnetic properties (B) Cutting hardness (C) Corrosion resistance (D) Ductility

Last Answer : (B) Cutting hardness

Acrylonitrile-butadiene-styrene (ABS) copolymer, which is produced by blending styrene-acrylonitrile copolymer with butadiene based elastomer, is a/an (A) Rigid foam (B) Engineering plastic (C) Thermosetting polymer

Description : Acrylonitrile-butadiene-styrene (ABS) copolymer, which is produced by blending styrene-acrylonitrile copolymer with butadiene based elastomer, is a/an (A) Rigid foam (B) Engineering plastic (C) Thermosetting polymer

Last Answer : (B) Engineering plastic

Bakelite is (A) Same as Polytetrafluoroethylene (PTFE) (B) An inorganic polymer (C) Same as thermosetting phenol-formaldehyde (D) Not a polymer

Description : Bakelite is (A) Same as Polytetrafluoroethylene (PTFE) (B) An inorganic polymer (C) Same as thermosetting phenol-formaldehyde (D) Not a polymer

Last Answer : (C) Same as thermosetting phenol-formaldehyde

Neoprene is rendered non-inflammable, because of (A) Its cross-linked structure (B) Its linear chain structure (C) The presence of chlorine atoms in its monomer (D) The absence of chlorine atoms in its monomer

Description : Neoprene is rendered non-inflammable, because of (A) Its cross-linked structure (B) Its linear chain structure (C) The presence of chlorine atoms in its monomer (D) The absence of chlorine atoms in its monomer

Last Answer : (C) The presence of chlorine atoms in its monomer