Gas turbine normally employs a constant __________ cycle. (A) Pressure (B) Temperature (C) Volume (D) None of these

Gas turbine normally employs a constant __________ cycle. (A) Pressure
(B) Temperature
(C) Volume
(D) None of these
by

1 Answer

Answer :

(A) Pressure
by

Related questions

Gas turbine cycle consists of  (a) two isothermals and two isentropics  (b) two isentropics and two constant volumes  (c) two isentropics, one constant volume and one constant pressure  (d) two isentropics and two constant pressures  (e) none of the above.

Description : Gas turbine cycle consists of  (a) two isothermals and two isentropics  (b) two isentropics and two constant volumes  (c) two isentropics, one constant volume and one constant pressure  (d) two isentropics and two constant pressures  (e) none of the above.

Last Answer : Answer : d

Claude process of gas liquefaction employs (A) Merely compression of gas beyond its critical pressure (B) Joule-Thomson expansion cooling (C) Heat exchange with colder stream (D) Adiabatic expansion against a piston or in a turbine

Description : Claude process of gas liquefaction employs (A) Merely compression of gas beyond its critical pressure (B) Joule-Thomson expansion cooling (C) Heat exchange with colder stream (D) Adiabatic expansion against a piston or in a turbine

Last Answer : (D) Adiabatic expansion against a piston or in a turbine

Linde process of gas liquefaction employs (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Adiabatic expansion against a piston or in a turbine (D) Merely compressing the gas beyond its critical pressure

Description : Linde process of gas liquefaction employs (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Adiabatic expansion against a piston or in a turbine (D) Merely compressing the gas beyond its critical pressure

Last Answer : (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion)

Claude's liquefaction process employs the cooling of gases by (A) Expansion in an engine (B) Following a constant pressure cycle (C) Throttling (D) None of these

Description : Claude's liquefaction process employs the cooling of gases by (A) Expansion in an engine (B) Following a constant pressure cycle (C) Throttling (D) None of these

Last Answer : A) Expansion in an engine

Claude gas liquefaction process employs cooling (A) At constant pressure (B) By throttling (C) By expansion in an engine (D) None of these

Description : Claude gas liquefaction process employs cooling (A) At constant pressure (B) By throttling (C) By expansion in an engine (D) None of these

Last Answer : (C) By expansion in an engine

Linde gas liquefaction process employs cooling (A) By throttling (B) By expansion in an engine (C) At constant pressure (D) None of these

Description : Linde gas liquefaction process employs cooling (A) By throttling (B) By expansion in an engine (C) At constant pressure (D) None of these

Last Answer : (A) By throttling

Which of the following diagramInternal energy is equal to the heat absorbed in case of a/an __________ process. (A) Constant volume (B) Polytropic (C) Adiabatic (D) Constant pressure s does not represent an Otto cycle?

Description : Which of the following diagrams does not represent an Otto cyInternal energy is equal to the heat absorbed in case of a/an __________ process. (A) Constant volume (B) Polytropic (C) Adiabatic (D) Constant pressure cle?

Last Answer : (A) Constant volume

Carnot cycle is also termed as the constant __________ cycle in thermodynamics. (A) Entropy (B) Pressure (C) Volume (D) Heat

Description : Carnot cycle is also termed as the constant __________ cycle in thermodynamics. (A) Entropy (B) Pressure (C) Volume (D) Heat

Last Answer : Option D

Keeping the pressure constant, to double the volume of a given mass of an ideal gas at 27°C, the temperature should be raised to __________ °C. (A) 270 (B) 327 (C) 300 (D) 540

Description : Keeping the pressure constant, to double the volume of a given mass of an ideal gas at 27°C, the temperature should be raised to __________ °C. (A) 270 (B) 327 (C) 300 (D) 540

Last Answer : (B) 327

A jet engine turbine blade is normally manufactured by (A) Forging (B) Shell moulding (C) Investment casting (D) Pressure die casting

Description : A jet engine turbine blade is normally manufactured by (A) Forging (B) Shell moulding (C) Investment casting (D) Pressure die casting

Last Answer : (C) Investment casting

Pick out the wrong statement. (A) At constant pressure, solubility of a gas in a liquid diminishes with rise in temperature (B) Normally, the gases which are easily liquefied are more soluble in common solvents (C) The gases which are capable of forming ions in aqueous solution are much more soluble in water than in other solvents (D) At constant pressure, solubility of a gas in a liquid increases with rise in temperature

Description : Pick out the wrong statement. (A) At constant pressure, solubility of a gas in a liquid diminishes with rise in temperature (B) Normally, the gases which are easily liquefied are more soluble ... (D) At constant pressure, solubility of a gas in a liquid increases with rise in temperature

Last Answer : (A) At constant pressure, solubility of a gas in a liquid diminishes with rise in temperature

A fast breeder reactor (A) Utilises fast neutrons for causing fission (B) Converts fertile material (e.g., U-238) into fissile material (Pu-239) (C) Normally employs molten sodium as coolant (D) All (A), (B) and (C)

Description : A fast breeder reactor (A) Utilises fast neutrons for causing fission (B) Converts fertile material (e.g., U-238) into fissile material (Pu-239) (C) Normally employs molten sodium as coolant (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In a Rankine cycle, with the maximum steam temperature being fixed from metallurgical considerations, as the boiler pressure increases (a) The condenser load will increase [IES-1997] (b) The quality of turbine exhaust will decrease (c) The quality of turbine exhaust will increase (d) The quality of turbine exhaust will remain unchanged

Description : In a Rankine cycle, with the maximum steam temperature being fixed from metallurgical considerations, as the boiler pressure increases (a) The condenser load will increase [IES-1997] (b) The ... The quality of turbine exhaust will increase (d) The quality of turbine exhaust will remain unchanged

Last Answer : (b) The quality of turbine exhaust will decrease 

In a Rankine cycle, regeneration results in higher efficiency because (a) Pressure inside the boiler increases [GATE-2003] (b) Heat is added before steam enters the low pressure turbine (c) Average temperature of heat addition in the boiler increases (d) Total work delivered by the turbine increases

Description : In a Rankine cycle, regeneration results in higher efficiency because (a) Pressure inside the boiler increases [GATE-2003] (b) Heat is added before steam enters the low pressure turbine (c) ... temperature of heat addition in the boiler increases (d) Total work delivered by the turbine increases 

Last Answer : (c) Average temperature of heat addition in the boiler increases  

Which of the following quantities has the GREATEST influence on the overall efficiency of a conventional (Rankine cycle) electric generating station burning fossil fuels? w) steam temperature at the steam turbine inlet x) net heating value of the fuel y) steam pressure at the steam turbine inlet z) pounds of ash and sulfur per pound of fuel

Description : Which of the following quantities has the GREATEST influence on the overall efficiency of a conventional (Rankine cycle) electric generating station burning fossil fuels? w) steam temperature at the steam turbine ... pressure at the steam turbine inlet z) pounds of ash and sulfur per pound of fuel 

Last Answer : ANSWER: W -- STEAM TEMPERATURE AT THE STEAM TURBINE INLET 

According to Gay-Lussac law, the absolute pressure of a given mass of a perfect gas varies __________ as its absolute temperature, when the volume remains constant.  A. directly  B. indirectly

Description : According to Gay-Lussac law, the absolute pressure of a given mass of a perfect gas varies __________ as its absolute temperature, when the volume remains constant.  A. directly  B. indirectly

Last Answer : Answer: A

A refrigeration cycle is the same as a __________ cycle, (A) Turbine (B) Heat engine (C) Reversed heat engine (D) None of these

Description : A refrigeration cycle is the same as a __________ cycle, (A) Turbine (B) Heat engine (C) Reversed heat engine (D) None of these

Last Answer : C) Reversed heat engine

During which of following process does heat rejection take place in Carnot vapour cycle? [IES-1992] (a) Constant volume (b) constant pressure (c) Constant temperature (d) constant entropy

Description : During which of following process does heat rejection take place in Carnot vapour cycle? [IES-1992] (a) Constant volume (b) constant pressure (c) Constant temperature (d) constant entropy

Last Answer : (c) Constant temperature

Otto cycle is also known as  A. constant pressure cycle  B. constant volume cycle  C. constant temperature cycle  D. constant temperature and pressure cycle

Description : Otto cycle is also known as  A. constant pressure cycle  B. constant volume cycle  C. constant temperature cycle  D. constant temperature and pressure cycle

Last Answer : Answer: B

In a Carnot cycle, heat is transferred at  (a) constant pressure  (b) constant volume  (c) constant temperature  (d) constant enthaply  (e) any one of the above.

Description : In a Carnot cycle, heat is transferred at  (a) constant pressure  (b) constant volume  (c) constant temperature  (d) constant enthaply  (e) any one of the above.

Last Answer : Answer : c

Consideration of the creep is the most important in case of the (A) Blades of gas turbine (B) Piston of an I. C. engine (C) Flywheel of steam engine (D) Cycle chain

Description : Consideration of the creep is the most important in case of the (A) Blades of gas turbine (B) Piston of an I. C. engine (C) Flywheel of steam engine (D) Cycle chain

Last Answer : (A) Blades of gas turbine

Pick out the wrong statement. (A) Cold SBR is superior as compared to hot SBR (B) Polymerisation temperature can modify the properties of SBR (C) Production of cold SBR employs lower pressure as compared to that of hot SBR (D) None of these

Description : Pick out the wrong statement. (A) Cold SBR is superior as compared to hot SBR (B) Polymerisation temperature can modify the properties of SBR (C) Production of cold SBR employs lower pressure as compared to that of hot SBR (D) None of these

Last Answer : (D) None of these

Hydrocracking employs (A) High pressure & temperature(B) Low pressure & temperature(C) High pressure and low temperature(D) High temperature and low pressure

Description : Hydrocracking employs (A) High pressure & temperature (B) Low pressure & temperature (C) High pressure and low temperature (D) High temperature and low pressure

Last Answer : (A) High pressure & temperature

Pick out the wrong statement(A) Cold rubber (SBR) is superior as compared to hot rubber (SBR)(B) Polymerisation temperature can modify the properties of SBR(C) Production of cold SBR employs lower pressure as compared to that ofhot SBR(D) None of these

Description : Pick out the wrong statement (A) Cold rubber (SBR) is superior as compared to hot rubber (SBR) (B) Polymerisation temperature can modify the properties of SBR (C) Production of cold SBR employs lower pressure as compared to that of hot SBR (D) None of these

Last Answer : (D) None of these

Clausius-Clapeyron Equation gives accurate result, when the (A) Vapour pressure is relatively low and the temperature does not vary over wide limits (B) Vapour obeys the ideal gas law and the latent heat of vaporisation is constant (C) Volume in the liquid state is negligible compared with that in the vapour state (D) All (A), (B) and (C)

Description : Clausius-Clapeyron Equation gives accurate result, when the (A) Vapour pressure is relatively low and the temperature does not vary over wide limits (B) Vapour obeys the ideal gas law and the latent heat of ... is negligible compared with that in the vapour state (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The internal energy of a gas obeying P (V - b) RT (where, b is a positive constant and has a constant Cv ), depends upon its (A) Pressure (B) Volume (C) Temperature (D) All (A), (B) & (C)

Description : The internal energy of a gas obeying P (V - b) RT (where, b is a positive constant and has a constant Cv ), depends upon its (A) Pressure (B) Volume (C) Temperature (D) All (A), (B) & (C)

Last Answer : (C) Temperature

The expression, ∆G = nRT. ln(P2/P1), gives the free energy change (A) With pressure changes at constant temperature (B) Under reversible isothermal volume change (C) During heating of an ideal gas (D) During cooling of an ideal gas

Description : The expression, ∆G = nRT. ln(P2/P1), gives the free energy change (A) With pressure changes at constant temperature (B) Under reversible isothermal volume change (C) During heating of an ideal gas (D) During cooling of an ideal gas

Last Answer : (A) With pressure changes at constant temperature

Which of the following will increase the volume of a real gas by four times? (A) Doubling the absolute temperature as well as pressure of the gas (B) Reducing pressure to one fourth at constant temperature (C) Reducing temperature to one fourth at constant pressure (D) Reducing the temperature to half and doubling the pressure

Description : Which of the following will increase the volume of a real gas by four times? (A) Doubling the absolute temperature as well as pressure of the gas (B) Reducing pressure to one fourth at ... temperature to one fourth at constant pressure (D) Reducing the temperature to half and doubling the pressure

Last Answer : (B) Reducing pressure to one fourth at constant temperature

Pick out the wrong statement. (A) The conversion for a gas phase reaction increases with decrease in pressure, if there is an increase in volume accompanying the reaction (B) With increase in temperature, the equilibrium constant increases for an exothermic reaction (C) The equilibrium constant of a reaction depends upon temperature only (D) The conversion for a gas phase reaction increases with increase in pressure, if there is a decrease in volume accompanying the reaction

Description : Pick out the wrong statement. (A) The conversion for a gas phase reaction increases with decrease in pressure, if there is an increase in volume accompanying the reaction (B) With ... phase reaction increases with increase in pressure, if there is a decrease in volume accompanying the reaction

Last Answer : (B) With increase in temperature, the equilibrium constant increases for an exothermic reaction

1m3 of an ideal gas at 500 K and 1000 kPa expands reversibly to 5 times its initial volume in an insulated container. If the specific heat capacity (at constant pressure) of the gas is 21 J/mole . K, the final temperature will be (A) 35 K (B) 174 K (C) 274 K (D) 154 K

Description : 1m3 of an ideal gas at 500 K and 1000 kPa expands reversibly to 5 times its initial volume in an insulated container. If the specific heat capacity (at constant pressure) of the gas is 21 J/mole . K, the final temperature will be (A) 35 K (B) 174 K (C) 274 K (D) 154 K

Last Answer : (C) 274 K

The thermodynamic law, PVy = constant, is not applicable in case of (A) Ideal compression of air (B) Free expansion of an ideal gas (C) Adiabatic expansion of steam in a turbine (D) Adiabatic compression of a perfect gas

Description : The thermodynamic law, PVy = constant, is not applicable in case of (A) Ideal compression of air (B) Free expansion of an ideal gas (C) Adiabatic expansion of steam in a turbine (D) Adiabatic compression of a perfect gas

Last Answer : (B) Free expansion of an ideal gas

The thermodynamic law, PVy = constant, is not followed by the (A) Free expansion of an ideal gas (B) Adiabatic expansion of steam in turbine (C) Adiabatic compression of air (D) Ideal compression of air

Description : The thermodynamic law, PVy = constant, is not followed by the (A) Free expansion of an ideal gas (B) Adiabatic expansion of steam in turbine (C) Adiabatic compression of air (D) Ideal compression of air

Last Answer : Option A

The efficiency and work ratio of a simple gas turbine cycle are  A.low  B.very low  C.high  D.very high

Description : The efficiency and work ratio of a simple gas turbine cycle are  A.low  B.very low  C.high  D.very high

Last Answer : Answer: B

Difference between open and closed cycle gas turbine.

Description : Difference between open and closed cycle gas turbine.

Last Answer : Closed Cycle Gas Turbine Open Cycle Gas Turbine  It works on closed cycle. The working fluid is recirculates again and again. It is a clean cycle. It works on open cycle. The fresh charge is ... complex and costly. Open cycle gas turbine plant is simple and less costly.

The use of regenerator in a gas turbine cycle

Description : The use of regenerator in a gas turbine cycle  (1) increases efficiency but has no effect on output (2) increases output but has no effect on efficiency (3) increases both efficiency and output (4) increases efficiency but decreases output

Last Answer : The use of regenerator in a gas turbine cycle increases efficiency but has no effect on output

The vapour compression refrigerator employs the following cycle (a) Rankine (b) Carnot (c) Reversed Carnot. (d) Brayton

Description : The vapour compression refrigerator employs the following cycle (a) Rankine (b) Carnot (c) Reversed Carnot. (d) Brayton

Last Answer : Ans: c

The work done in an adiabatic change in a particular gas depends upon changes in the __________ only. (A) Temperature (B) Specific heat (C) Volume (D) Pressure

Description : The work done in an adiabatic change in a particular gas depends upon changes in the __________ only. (A) Temperature (B) Specific heat (C) Volume (D) Pressure

Last Answer : (A) Temperature

For an ideal gas, the internal energy depends upon its __________ only. (A) Molecular size (B) Temperature (C) Volume (D) Pressure

Description : For an ideal gas, the internal energy depends upon its __________ only. (A) Molecular size (B) Temperature (C) Volume (D) Pressure

Last Answer : (B) Temperature

The internal energy of an ideal gas is a function of its __________ only. (A) Molecular size (B) Volume (C) Pressure (D) Temperature

Description : The internal energy of an ideal gas is a function of its __________ only. (A) Molecular size (B) Volume (C) Pressure (D) Temperature

Last Answer : (D) Temperature

At a given temperature, the volume of a gas dissolved in a solvent __________ with increase in pressure. (A) Increases (B) Decreases (C) Remains unchanged (D) May increase or decrease; depends on the gas

Description : At a given temperature, the volume of a gas dissolved in a solvent __________ with increase in pressure. (A) Increases (B) Decreases (C) Remains unchanged (D) May increase or decrease; depends on the gas

Last Answer : C) Remains unchanged

Hydraulic __________ works on the principle of Pascal's law of transmission of fluid pressure. (A) Press (B) Turbine (C) Pump (D) Coupling

Description : Hydraulic __________ works on the principle of Pascal's law of transmission of fluid pressure. (A) Press (B) Turbine (C) Pump (D) Coupling

Last Answer : (A) Press

Yield of urea can be increased with excess ammonia and higher pressure & temperature, but because of __________ this is normally not done. (A) Increased biuret formation (B) High corrosion rate (C) Increased cost of equipment (D) All (A), (B) & (C)

Description : Yield of urea can be increased with excess ammonia and higher pressure & temperature, but because of __________ this is normally not done. (A) Increased biuret formation (B) High corrosion rate (C) Increased cost of equipment (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Most of the centrifugal pumps used in chemical plants are usually __________ driven. (A) Steam (B) Diesel engine (C) Electric motor (D) Gas turbine

Description : Most of the centrifugal pumps used in chemical plants are usually __________ driven. (A) Steam (B) Diesel engine (C) Electric motor (D) Gas turbine

Last Answer : (C) Electric motor

The air standard Otto cycle comprises a two constant pressure processes and two constant volume processes b two constant pressure and two constant entropy processes c. two constant volume processes and two constant entropy processes d. none of the above.

Description : The air standard Otto cycle comprises a two constant pressure processes and two constant volume processes b two constant pressure and two constant entropy processes c. two constant volume processes and two constant entropy processes d. none of the above.

Last Answer : ANSWER (c) two constant volume processes and two constant entropy processes

The dual combustion cycle consists of one constant pressure, two constant volume and two isentropic processes.  A. Agree  B. Disagree

Description : The dual combustion cycle consists of one constant pressure, two constant volume and two isentropic processes.  A. Agree  B. Disagree

Last Answer : Answer: A

A cycle consisting of one constant pressure, one constant volume and two isentropic processes is known as  A.Carnot cycle  B.Stirling cycle  C.Otto cycle  D.Diesel cycle

Description : A cycle consisting of one constant pressure, one constant volume and two isentropic processes is known as  A.Carnot cycle  B.Stirling cycle  C.Otto cycle  D.Diesel cycle

Last Answer : Answer: D

The cycle in which heat is supplied at constant volume and rejected at constant pressure is known as

Description : The cycle in which heat is supplied at constant volume and rejected at constant pressure is known as  (a) Dual combustion cycle  (b) Diesel cycle  (c) Atkinson cycle  (d) Rankine cycle  (e) Stirling cycle.

Last Answer : Answer : c

Brayton cycle consists’ of following four processes  (a) two isothermals and two isentropics  (b) two isentropics and two constant volumes  (c) two isentropics, one constant volume and one constant pressure  (d) two isentropics and two constant pres-sures  (e) none of the above.

Description : Brayton cycle consists’ of following four processes  (a) two isothermals and two isentropics  (b) two isentropics and two constant volumes  (c) two isentropics, one constant volume and one constant pressure  (d) two isentropics and two constant pres-sures  (e) none of the above.

Last Answer : Answer : d

Diesel cycle consists of following four processes  (a) two isothermals and two isentropics  (b) two isentropics, and two constant volumes.  (c) two isentropics, one constant volume and one constant pressure  (d) two isentropics and two constant pressures  (e) none of the above.

Description : Diesel cycle consists of following four processes  (a) two isothermals and two isentropics  (b) two isentropics, and two constant volumes.  (c) two isentropics, one constant volume and one constant pressure  (d) two isentropics and two constant pressures  (e) none of the above.

Last Answer : Answer : c