Solute atoms which cause yield point phenomenon in mild steel are/is (A) Aluminium (B) Boron (C) Carbon (D) Nitrogen

Solute atoms which cause yield point phenomenon in mild steel are/is (A) Aluminium
(B) Boron
(C) Carbon
(D) Nitrogen
by

1 Answer

Answer :

(C) Carbon
by

Related questions

The yield point phenomenon observed in annealed low carbon steel is due to the presence of the following element. (A) Silicon (B) Carbon (C) Phosphorous (D) Chromium

Description : The yield point phenomenon observed in annealed low carbon steel is due to the presence of the following element. (A) Silicon (B) Carbon (C) Phosphorous (D) Chromium

Last Answer : Option B

Consider the following salient points in a stress-strain curve of a mild steel bar: 1. Yield point 2. Braking point 3. Yield plateau 4 . Proportionality limit 5. Ultimate point The correct sequence in which they occur while testing the mild steel bar in tension from initial zero strain to failure is (a) 4, 1, 2, 3 and 5 (b) 1, 4, 3, 5 and 2 (c) 4, 1, 3, 5 and 2 (d) 1, 4, 2, 3 and 5

Description : Consider the following salient points in a stress-strain curve of a mild steel bar: 1. Yield point 2. Braking point 3. Yield plateau 4 . Proportionality limit 5. Ultimate point The correct sequence in which they occur while testing the mild ... , 5 and 2 (c) 4, 1, 3, 5 and 2 (d) 1, 4, 2, 3 and 5

Last Answer : (c) 4, 1, 3, 5 and 2

Which of the following materials may prove unsuitable for handling acetic acid (glacial & anhydrous) at 40°C? (A) Silicone rubber, teflon, porcelain and wood (B) Nickel, monel, stainless steel and graphite (C) Aluminium, copper, high silicon iron (D) Brass, cast iron, mild steel and tin

Description : Which of the following materials may prove unsuitable for handling acetic acid (glacial & anhydrous) at 40°C? (A) Silicone rubber, teflon, porcelain and wood (B) Nickel, monel, stainless steel and graphite (C) Aluminium, copper, high silicon iron (D) Brass, cast iron, mild steel and tin

Last Answer : (D) Brass, cast iron, mild steel and tin

The preferred material of construction for storage tanks for 98% sulphuric acid is (A) Aluminium (B) Lead (C) Stainless steel 316 (D) Mild steel

Description : The preferred material of construction for storage tanks for 98% sulphuric acid is (A) Aluminium (B) Lead (C) Stainless steel 316 (D) Mild steel

Last Answer : (B) Lead

Acetaldehyde is produced by hydration of acetylene in a sulphuric acid solution of mercuric sulphate. Hydration tower is made of (A) Rubber lined mild steel (B) Lead lined mild steel (C) Aluminium (D) Cast iron

Description : Acetaldehyde is produced by hydration of acetylene in a sulphuric acid solution of mercuric sulphate. Hydration tower is made of (A) Rubber lined mild steel (B) Lead lined mild steel (C) Aluminium (D) Cast iron

Last Answer : (A) Rubber lined mild steel

H2SO4 (< 50% concentration) is corrosive to (A) Aluminium, mild steel, stainless steel, concrete & tin (B) Copper, cast iron & high silicon iron (14% Si) (C) Rubber (butyl and hard), silicone rubber & Teflon (D) Glass, graphite, porcelain & stoneware

Description : H2SO4 (< 50% concentration) is corrosive to (A) Aluminium, mild steel, stainless steel, concrete & tin (B) Copper, cast iron & high silicon iron (14% Si) (C) Rubber (butyl and hard), silicone rubber & Teflon (D) Glass, graphite, porcelain & stoneware

Last Answer : (A) Aluminium, mild steel, stainless steel, concrete & tin

100% H2SO4 at 30°C can't be stored in a vessel made/lined with (A) Cast iron and high silicon iron (B) Mild steel and stainless steel (C) Aluminium, tin and rubber (D) Teflon, glass and porcelain

Description : 100% H2SO4 at 30°C can't be stored in a vessel made/lined with (A) Cast iron and high silicon iron (B) Mild steel and stainless steel (C) Aluminium, tin and rubber (D) Teflon, glass and porcelain

Last Answer : (C) Aluminium, tin and rubber

Which of the following material of construction may be recommended by a chemical engineer for handling a gaseous chlorine (dry or wet) stream in a fluid flow system? (A) High silicon iron, silicon rubber, Kel-F and Teflon (B) Mild steel and stainless steel (C) Cast iron, tin and aluminium (D) Copper, nickel and Monel

Description : Which of the following material of construction may be recommended by a chemical engineer for handling a gaseous chlorine (dry or wet) stream in a fluid flow system? (A) High silicon iron, silicon rubber ... Mild steel and stainless steel (C) Cast iron, tin and aluminium (D) Copper, nickel and Monel

Last Answer : (A) High silicon iron, silicon rubber, Kel-F and Teflon

The heat transfer by radiation from a mild steel surface is to be reduced by reducing the emissivity of the surface. This can be best achieved by (A) Painting the surface black (B) Painting the surface white (with aluminium paint) (C) Giving the surface a mirror finish (D) Roughening the surface

Description : The heat transfer by radiation from a mild steel surface is to be reduced by reducing the emissivity of the surface. This can be best achieved by (A) Painting the surface black (B) ... white (with aluminium paint) (C) Giving the surface a mirror finish (D) Roughening the surface

Last Answer : (B) Painting the surface white (with aluminium paint)

Which of the following will have the highest melting point? (A) Pig iron (B) Mild steel (C) Wrought iron (D) High carbon stee

Description : Which of the following will have the highest melting point? (A) Pig iron (B) Mild steel (C) Wrought iron (D) High carbon stee

Last Answer : (C) Wrought iron

Silicon crystal can be converted to p-type semi-conductor by doping with (A) Phosphorous (B) Nitrogen (C) Carbon (D) Boron

Description : Silicon crystal can be converted to p-type semi-conductor by doping with (A) Phosphorous (B) Nitrogen (C) Carbon (D) Boron

Last Answer : Option D

is usually used for brush rockers (a) Mild steel (b) Copper (c) Aluminium (d) Cast-iron

Description : is usually used for brush rockers (a) Mild steel (b) Copper (c) Aluminium (d) Cast-iron

Last Answer : (d) Cast-iron

Safety rods provided in nuclear reactors to guard against accidents, in case of earthquake are made of (A) High carbon steel (B) Molybdenum (C) Zircaloy (D) Boron or cadmium

Description : Safety rods provided in nuclear reactors to guard against accidents, in case of earthquake are made of (A) High carbon steel (B) Molybdenum (C) Zircaloy (D) Boron or cadmium

Last Answer : (D) Boron or cadmium

__________ is added in low carbon steel to raise its yield point. (A) Sulphur (B) Phosphorous (C) Silicon (D) Manganese

Description : __________ is added in low carbon steel to raise its yield point. (A) Sulphur (B) Phosphorous (C) Silicon (D) Manganese

Last Answer : (D) Manganese

The element with the least atomic size from Carbon, Nitrogen, Boron and Beryllium is

Description : The element with the least atomic size from Carbon, Nitrogen, Boron and Beryllium is

Last Answer : Nitrogen.

Which of the following groups of elements have an OUTER ELECTRONIC configuration of S-2-P-2? w) halogens x) Nitrogen-Phosphorus Group y) Carbon-Silicon Group z) Boron-Aluminum Group

Description : Which of the following groups of elements have an OUTER ELECTRONIC configuration of S-2-P-2? w) halogens x) Nitrogen-Phosphorus Group y) Carbon-Silicon Group z) Boron-Aluminum Group

Last Answer : ANSWER: Y -- CARBON-SILICON GROUP

It is believed that carbon-14 in nature is slowly generated by the action of: w) protons on carbon-12 x) electrons on hydrogen y) cosmic rays on boron z) neutrons on nitrogen

Description : It is believed that carbon-14 in nature is slowly generated by the action of: w) protons on carbon-12 x) electrons on hydrogen y) cosmic rays on boron z) neutrons on nitrogen

Last Answer : ANSWER: Z -- NEUTRONS ON NITROGEN 

Which of the following would have the largest THIR ionization energy? Is it: w) Boron x) Carbon y) Nitrogen z) Magnesium

Description : Which of the following would have the largest THIR ionization energy? Is it: w) Boron x) Carbon y) Nitrogen z) Magnesium

Last Answer : ANSWER: Z -- MAGNESIUM

Which of these is a micronutrient for plants? (1) Carbon (2) Oxygen (3) Nitrogen (4) Boron

Description : Which of these is a micronutrient for plants? (1) Carbon (2) Oxygen (3) Nitrogen (4) Boron

Last Answer : Boron

The main constituent of carborundum is __________ carbide. (A) Calcium (B) Silicon (C) Boron (D) Aluminium

Description : The main constituent of carborundum is __________ carbide. (A) Calcium (B) Silicon (C) Boron (D) Aluminium

Last Answer : (B) Silicon

hich of the following is the most suitable abrasive for grinding high tensile strength materials? (A) Silicon carbide (B) Corundum (C) Aluminium oxide (D) Boron carbide

Description : hich of the following is the most suitable abrasive for grinding high tensile strength materials? (A) Silicon carbide (B) Corundum (C) Aluminium oxide (D) Boron carbide

Last Answer : Option C

Which of the following has the least carbon percentage? (A) Low carbon steel (B) Mild steel (C) Wrought iron (D) White cast iron

Description : Which of the following has the least carbon percentage? (A) Low carbon steel (B) Mild steel (C) Wrought iron (D) White cast iron

Last Answer : (C) Wrought iron

Carbon percentage is the same in cast iron and (A) Wrought iron(B) Pig iron(C) Mild steel(D) High silicon (14%) iron

Description : Carbon percentage is the same in cast iron and (A) Wrought iron (B) Pig iron (C) Mild steel (D) High silicon (14%) iron

Last Answer : (B) Pig iron

Which one is remelted and poured into moulds to get cast iron? (A) Wrought iron (B) Pig iron (C) Low carbon steel (D) Mild steel

Description : Which one is remelted and poured into moulds to get cast iron? (A) Wrought iron (B) Pig iron (C) Low carbon steel (D) Mild steel

Last Answer : (B) Pig iron

Hammers and railway rails are normally made of(A) Mild steel(B) Dead mild steel(C) Medium carbon steel(D) High carbon stee

Description : Hammers and railway rails are normally made of (A) Mild steel (B) Dead mild steel (C) Medium carbon steel (D) High carbon stee

Last Answer : (D) High carbon stee

Which of the following has the poorest weldability? (A) Low carbon steel (B) Mild steel (C) Wrought iron (D) High-carbon steel

Description : Which of the following has the poorest weldability? (A) Low carbon steel (B) Mild steel (C) Wrought iron (D) High-carbon steel

Last Answer : (D) High-carbon steel

Mild steel is (A) A low carbon steel (0.05 to 0.3% carbon) (B) Highly resistant to corrosion (as much as stainless steel) (C) A high carbon steel (0.5 to 1.5% carbon) (D) Very poor in strength & ductility

Description : Mild steel is (A) A low carbon steel (0.05 to 0.3% carbon) (B) Highly resistant to corrosion (as much as stainless steel) (C) A high carbon steel (0.5 to 1.5% carbon) (D) Very poor in strength & ductility

Last Answer : (A) A low carbon steel (0.05 to 0.3% carbon)

Dead mild steel, which contains 0.10 to 0.15 percent carbon is used for making (A) Shafts (B) Flanges (C) Gears (D) Shear blades

Description : Dead mild steel, which contains 0.10 to 0.15 percent carbon is used for making (A) Shafts (B) Flanges (C) Gears (D) Shear blades

Last Answer : (B) Flanges

Which of the following has the highest compressive strength? (A) Wrought iron (B) Cast iron (C) Mild steel (D) High carbon steel

Description : Which of the following has the highest compressive strength? (A) Wrought iron (B) Cast iron (C) Mild steel (D) High carbon steel

Last Answer : (D) High carbon steel

Dies for wire drawing are generally made of (A) Mild steel (B) Stainless steel (C) Carbides (D) High carbon stee

Description : Dies for wire drawing are generally made of (A) Mild steel (B) Stainless steel (C) Carbides (D) High carbon stee

Last Answer : (C) Carbides

An alloy of iron containing 4% carbon is called (A) High carbon steel (B) Wrought iron (C) Mild steel (D) None of these

Description : An alloy of iron containing 4% carbon is called (A) High carbon steel (B) Wrought iron (C) Mild steel (D) None of these

Last Answer : (D) None of these

Mild steel is a/an __________ steel. (A) Low carbon (B) Medium carbon (C) High carbon (D) High alloy

Description : Mild steel is a/an __________ steel. (A) Low carbon (B) Medium carbon (C) High carbon (D) High alloy

Last Answer : (A) Low carbon

Mild steel is a/an __________ steel. (A) Low carbon (B) Medium carbon (C) High carbon (D) High alloy

Description : Mild steel is a/an __________ steel. (A) Low carbon (B) Medium carbon (C) High carbon (D) High alloy

Last Answer : (A) Low carbon

In a drilling process, the metal is removed by both shearing & extrusion. General purpose drills are made of (A) Stainless steel (B) Mild steel (C) High speed steel (D) High carbon steel

Description : In a drilling process, the metal is removed by both shearing & extrusion. General purpose drills are made of (A) Stainless steel (B) Mild steel (C) High speed steel (D) High carbon steel

Last Answer : (C) High speed steel

Cold chisel’s hammers are made of (A) High speed steel (B) High carbon steel (C) Forged steel (D) Mild steel

Description : Cold chisel’s hammers are made of (A) High speed steel (B) High carbon steel (C) Forged steel (D) Mild steel

Last Answer : (B) High carbon steel

Cold chisel & hammers are made of (A) High speed steel (B) High carbon steel (C) Forged steel (D) Mild steel

Description : Cold chisel & hammers are made of (A) High speed steel (B) High carbon steel (C) Forged steel (D) Mild steel

Last Answer : (B) High carbon steel

Oxyacetylene reducing flame is used while carrying out welding on (A) Alloy steel (B) Grey cast iron (C) Mild steel (D) High carbon steel

Description : Oxyacetylene reducing flame is used while carrying out welding on (A) Alloy steel (B) Grey cast iron (C) Mild steel (D) High carbon steel

Last Answer : (C) Mild steel

Dies for wire drawing are generally made of (A) Mild steel (B) Stainless steel (C) Carbides (D) High carbon steel

Description : Dies for wire drawing are generally made of (A) Mild steel (B) Stainless steel (C) Carbides (D) High carbon steel

Last Answer : (A) Mild steel

Oxyacetylene reducing flame is used while carrying out welding on (A) Alloy steel (B) Grey cast iron (C) Mild steel (D) High carbon steel

Description : Oxyacetylene reducing flame is used while carrying out welding on (A) Alloy steel (B) Grey cast iron (C) Mild steel (D) High carbon steel

Last Answer : Option C

Pick out the wrong statement. (A) Addition of methane to the furnace atmosphere reduces decarburising by hydrogen (B) Nitrogen in presence of steam decor-burises high carbon steel, whereas hydrocarbon gases carburise the surface of steel at annealing temperatures (C) Active nitrogen (formed by cracking ammonia at the metal surface) cause nitride formation with increase in surface hardness (D) None of these

Description : Pick out the wrong statement. (A) Addition of methane to the furnace atmosphere reduces decarburising by hydrogen (B) Nitrogen in presence of steam decor-burises high carbon steel, whereas hydrocarbon ... the metal surface) cause nitride formation with increase in surface hardness (D) None of these

Last Answer : (D) None of these

Manganese is added in low carbon steel to A. Make the steel tougher and harder B. Raise the yield point C. Make the steel ductile and of good bending qualities D. All of the above

Description : Manganese is added in low carbon steel to A. Make the steel tougher and harder B. Raise the yield point C. Make the steel ductile and of good bending qualities D. All of the above

Last Answer : C. Make the steel ductile and of good bending qualities

Fatty acids with odd number of carbon atoms yield acetyl-CoA and a molecule of (A) Succinyl-CoA (B) Propionyl-CoA (C) Malonyl-CoA (D) Acetoacetyl-CoA

Description : Fatty acids with odd number of carbon atoms yield acetyl-CoA and a molecule of (A) Succinyl-CoA (B) Propionyl-CoA (C) Malonyl-CoA (D) Acetoacetyl-CoA

Last Answer : Answer : B

Both rubies and sapphires contain (a) silicon dioxide (b) lead tetroxide (c) aluminium oxide (d) boron nitride

Description : Both rubies and sapphires contain (a) silicon dioxide (b) lead tetroxide (c) aluminium oxide (d) boron nitride

Last Answer : Ans:(c)

The steel generally used in R.C.C. work, is (A) Stainless (B) Mild steel (C) High carbon steel (D) High tension steel

Description : The steel generally used in R.C.C. work, is (A) Stainless (B) Mild steel (C) High carbon steel (D) High tension steel

Last Answer : Answer: Option B

Select the correct statement (A) Elastic modulus of high tensile steel is nearly the same as that of mild steel (B) Elastic modulus of high tensile steel is more than that of mild steel (C) Carbon percentage in high carbon steel is less than that in mild steel (D) High tensile steel is cheaper than mild steel

Description : Select the correct statement (A) Elastic modulus of high tensile steel is nearly the same as that of mild steel (B) Elastic modulus of high tensile steel is more than that of mild steel (C) ... high carbon steel is less than that in mild steel (D) High tensile steel is cheaper than mild steel

Last Answer : Answer: Option A

The steel used in R.C.C. work is (A) Stainless steel (B) Mild steel (C) High carbon steel (D) Wrought iron

Description : The steel used in R.C.C. work is (A) Stainless steel (B) Mild steel (C) High carbon steel (D) Wrought iron

Last Answer : Answer: Option B

Percentage of carbon content in mild steel is (A) Less than 0.25 (B) Between 0.25 and 0.7 (C) Between 0.7 and 1.5 (D) Greater than 1.5

Description : Percentage of carbon content in mild steel is (A) Less than 0.25 (B) Between 0.25 and 0.7 (C) Between 0.7 and 1.5 (D) Greater than 1.5

Last Answer : Answer: Option A

Which of the following is the purest form of iron? (A) Cast iron (B) Wrought iron (C) Mild steel (D) High carbon steel

Description : Which of the following is the purest form of iron? (A) Cast iron (B) Wrought iron (C) Mild steel (D) High carbon steel

Last Answer : Answer: Option B

The shovel of seed drill is made up of: A. Cast iron B. Mild steel C. White metal D. Carbon steel

Description : The shovel of seed drill is made up of: A. Cast iron B. Mild steel C. White metal D. Carbon steel

Last Answer : Carbon steel

Mild steel is an alloy with carbon content a)0.25%. b)5% c)10%. d)25%

Description : Mild steel is an alloy with carbon content a)0.25%. b)5% c)10%. d)25%

Last Answer : a)0.25%.