Pick up the correct statement applicable to plate load test (A) Width of the test pit for plate load test is made five times the width of the plate (B) At the centre of the test pit, a hole is dug out whose size is kept equal to the size of the test plate (C) Bottom level of the hole dug at the centre of the test pit, is kept at the level of the actual formation (D) All the above

Pick up the correct statement applicable to plate load test
(A) Width of the test pit for plate load test is made five times the width of the plate
(B) At the centre of the test pit, a hole is dug out whose size is kept equal to the size of the test
plate
(C) Bottom level of the hole dug at the centre of the test pit, is kept at the level of the actual
formation
(D) All the above
by

1 Answer

Answer :

Answer: Option D
by

Related questions

Pick up the incorrect statement from the following: (A) Tresguet did not provide the top camber for the drainage of surface water (B) Tresguet provided the top camber for the drainage of surface water (C) Telford provided two layers of stones in the central 5.4 m width and one layer was provided on the sides (D) Macadam provided a camber to the formation at the dug-up state, to drain percolated water

Description : Pick up the incorrect statement from the following: (A) Tresguet did not provide the top camber for the drainage of surface water (B) Tresguet provided the top camber for the drainage of surface ... (D) Macadam provided a camber to the formation at the dug-up state, to drain percolated water

Last Answer : Answer: Option A

Pick up the correct statement from the following: (A) Inclined borings are made for taking samples under existing structures (B) Inclined borings are occasionally used instead of vertical holes (C) The spacing of inclined borings is kept such that one bore hole is vertically above the bottom of an adjacent bore hole (D) All the above

Description : Pick up the correct statement from the following: (A) Inclined borings are made for taking samples under existing structures (B) Inclined borings are occasionally used instead of vertical holes (C) The ... bore hole is vertically above the bottom of an adjacent bore hole (D) All the above

Last Answer : Answer: Option D

If water table is encountered in the standard pit while conducting plate load test (a) The load test should be abandoned (b) The pit is considered unsafe (c) Test should be conducted with complete dewatering continuously throughout the test duration (d) The bearing capacity of soil cannot be determined in this condition

Description : If water table is encountered in the standard pit while conducting plate load test (a) The load test should be abandoned (b) The pit is considered unsafe (c) Test should be conducted ... continuously throughout the test duration (d) The bearing capacity of soil cannot be determined in this condition

Last Answer : (c) Test should be conducted with complete dewatering continuously throughout the test duration

Which one of the following statements regarding septic tanks is wrong? A. A gap of 7.5 cm between the bottom of the covering slab and the top level of scum is provided B. The outlet invert level is kept 5 to 7.5 cm below the inlet invert level C. The minimum width of septic level is 90 cm D. The depth of tank is kept equal to its width

Description : Which one of the following statements regarding septic tanks is wrong? A. A gap of 7.5 cm between the bottom of the covering slab and the top level of scum is provided B. The outlet invert level is kept ... . The minimum width of septic level is 90 cm D. The depth of tank is kept equal to its width

Last Answer : ANS: D

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material

Description : For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material

Last Answer : a) Increase

Pick up the correct statement from the following: (A) The apparent error on reversal is twice the actual error (B) The correction may be made equal to half the observed discrepancy (C) The good results may be obtained from a defective instrument by reversing and taking the mean of two erroneous results (D) All the above

Description : Pick up the correct statement from the following: (A) The apparent error on reversal is twice the actual error (B) The correction may be made equal to half the observed discrepancy (C) The ... a defective instrument by reversing and taking the mean of two erroneous results (D) All the above

Last Answer : (D) All the above

Pick up the correct statement from the following: (A) A pile is a slender member which transfers the load through its lower end on a strong strata (B) A pile is a slender member which transfers its load to the surrounding soil (C) A pile is a slender member which transfers its load by friction (D) A pile is a cylindrical body of concrete which transfers the load at a depth greater than its width

Description : Pick up the correct statement from the following: (A) A pile is a slender member which transfers the load through its lower end on a strong strata (B) A pile is a slender member which ... A pile is a cylindrical body of concrete which transfers the load at a depth greater than its width

Last Answer : Answer: Option B

Pick up the incorrect statement from the following: (A) The bottom and top ends of slump mould are parallel to each other (B) The axis of the mould is perpendicular to the end faces (C) The internal surface of the mould is kept clean and free from set cement (D) The mould is in the form of a frustum of hexagonal pyramid

Description : Pick up the incorrect statement from the following: (A) The bottom and top ends of slump mould are parallel to each other (B) The axis of the mould is perpendicular to the end faces (C) The ... clean and free from set cement (D) The mould is in the form of a frustum of hexagonal pyramid

Last Answer : Answer: Option D

If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection of the beam at the centre is changed by (A) 2 times (B) 4 times (C) 8 times (D) 1/2 times

Description : If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection of the beam at the centre is changed by (A) 2 times (B) 4 times (C) 8 times (D) 1/2 times

Last Answer : (C) 8 times

In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Description : In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Last Answer : b) 450 N/mm2

Ground water is recharged by different aquifers, which of the following is not an aquifer: a. Bore well b. Dug well c. Sprinkler. D. Recharge pit

Description : Ground water is recharged by different aquifers, which of the following is not an aquifer: a. Bore well b. Dug well c. Sprinkler. D. Recharge pit

Last Answer : c. Sprinkler

Pick up the incorrect statement from the following. The width of the right-of-way is decided so as to accommodate (A) Formation width (B) Side slopes (C) Horizontal curve (D) Vertical curve

Description : Pick up the incorrect statement from the following. The width of the right-of-way is decided so as to accommodate (A) Formation width (B) Side slopes (C) Horizontal curve (D) Vertical curve

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) If the bed level is above N.S.L. the canal is called fully in baking and the berms are designed as 3 d where d is full supply depth of water (F.S.D.) (B) Area of canal in cutting = BD + Sd 2 where B = bed width, d = depth of cutting and S is the side slope (C) If F.S.L. is above N.S.L the canal is called partly in cutting and partly in filling and berms are designed as 2d where d is full supply depth (D) All the above

Description : Pick up the correct statement from the following: (A) If the bed level is above N.S.L. the canal is called fully in baking and the berms are designed as 3 d where d is full supply depth of water ... and partly in filling and berms are designed as 2d where d is full supply depth (D) All the above

Last Answer : (D) All the above

Pick up the correct statement from the following: (A) In order to check up the average depth of excavation, 'Dead man s' are left at the midwidths of borrow pits (B) The earthwork calculation in excavation is made from the difference in levels obtained with a level (C) The earth work in excavation to form the road embankment includes the formation of correct profile and depositing the soil in layers (D) All the above

Description : Pick up the correct statement from the following: (A) In order to check up the average depth of excavation, 'Dead man s' are left at the midwidths of borrow pits (B) The earthwork ... embankment includes the formation of correct profile and depositing the soil in layers (D) All the above

Last Answer : (D) All the above

Pick up the incorrect statement applicable to the field test of good cement. (A) When one thrusts one's hand into a bag of cement, one should feel warm (B) The colour of the cement is bluish (C) By rubbing cement in between fingers, one should feed rough (D) All the above

Description : Pick up the incorrect statement applicable to the field test of good cement. (A) When one thrusts one's hand into a bag of cement, one should feel warm (B) The colour of the cement is bluish (C) By rubbing cement in between fingers, one should feed rough (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) When rainfall rate exceeds the infiltration capacity, the water enters the soil at full capacity rate (B) When rainfall rate is less than the infiltration capacity, the infiltration rate is approximately equal to the rainfall rate (C) The actual infiltration rate at any time may be equal to or less than the infiltration capacity (D) All the above

Description : Pick up the correct statement from the following: (A) When rainfall rate exceeds the infiltration capacity, the water enters the soil at full capacity rate (B) When rainfall rate is less than the ... rate at any time may be equal to or less than the infiltration capacity (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) Absolute humidity at a given temperature is equal to weight of moisture present in a unit volume (B) Relative humidity is the ratio of actual vapour pressure and saturation vapour pressure at the same temperature (C) Relative humidity is the ratio of the weight of the vapours present per unit volume to the weight of vapours which could be contained at the same temperature when fully saturated (D) All the above

Description : Pick up the correct statement from the following: (A) Absolute humidity at a given temperature is equal to weight of moisture present in a unit volume (B) Relative humidity is the ratio of ... of vapours which could be contained at the same temperature when fully saturated (D) All the above

Last Answer : Answer: Option D

Pick out the wrong statement pertaining to fluid flow. (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5 (B) The Newtonian fluid velocity in a circular pipe flow is maximum at the centre of the pipe (C) Navier-Stokes equation is applicable to the analysis of viscous flows

Description : Pick out the wrong statement pertaining to fluid flow. (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5 (B) The Newtonian ... at the centre of the pipe (C) Navier-Stokes equation is applicable to the analysis of viscous flows

Last Answer : (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5

Pick up the incorrect statement from the following: (A) The width of the wall is constructed thicker at the base in a stepped fashion (B) A long vertical load transferring concrete structure is called a concrete pile (C) In pile which transfers the load to the soil by the friction between the pile and the surrounding soil is called friction pile (D) The pile which transfers the load to a hard rock bed at certain depth is called load bearing

Description : Pick up the incorrect statement from the following: (A) The width of the wall is constructed thicker at the base in a stepped fashion (B) A long vertical load transferring concrete structure is ... ) The pile which transfers the load to a hard rock bed at certain depth is called load bearing

Last Answer : Answer: Option D

0 Pick up the correct statement from the following: (A) The point through which the resultant of the shear stresses passes is known as shear centre(B) In the standard rolled channels, the shear centre is on the horizontal line passing through and away from the C.G. beyond web (C) In equal angles, the shear centre is on the horizontal plane and away from the C.G., outside of the leg projection (D) All the above

Description : 0 Pick up the correct statement from the following: (A) The point through which the resultant of the shear stresses passes is known as shear centre (B) In the standard rolled channels, the shear centre ... horizontal plane and away from the C.G., outside of the leg projection (D) All the above

Last Answer : (D) All the above

For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Description : For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Last Answer : Answer: Option D

How much dirt is in a hole that was dug 5m deep and 6m wide? -Riddles

Description : How much dirt is in a hole that was dug 5m deep and 6m wide? -Riddles

Last Answer : There is no dirt because it was dug out.

How much dirt would be in a hole 6 feet deep and 6 feet wide that has been dug with a square edged shovel?

Description : How much dirt would be in a hole 6 feet deep and 6 feet wide that has been dug with a square edged shovel?

Last Answer : None. No matter how big a hole is, it's still a hole: the absence of dirt.

Pick up the correct statement from the following: (A) Bulking of sand is caused due to formation of a thin film of surface moisture (B) Fine sand bulks more than coarse sand (C) The volume of fully saturated sand, is equal to the volume of dry and loose sand (D) All the above

Description : Pick up the correct statement from the following: (A) Bulking of sand is caused due to formation of a thin film of surface moisture (B) Fine sand bulks more than coarse sand (C) The volume of fully saturated sand, is equal to the volume of dry and loose sand (D) All the above

Last Answer : Answer: Option D

1. Which of the statements with regard to formation is correct (1) One of the Functions of the formation is to facilitate drainage (2) Width of bank for double railway line is 12.155 meters (3) Width of cutting for double railway track is 11.750 meters (4) Centre to centre of formation for double line is 4.725 meters (5) Width of formation is different for concrete sleeper track and other than concrete sleeper track a) 2, 3, 5 b) 3, 4, 5* c) 2, 3, 4 d) 2, 4, 5

Description : 1. Which of the statements with regard to formation is correct (1) One of the Functions of the formation is to facilitate drainage (2) Width of bank for double railway line is 12.155 meters (3) Width of cutting for double railway track is 11. ... a) 2, 3, 5 b) 3, 4, 5* c) 2, 3, 4 d) 2, 4, 5

Last Answer : b) 3, 4, 5*

If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection of the beam at the centre is changed by (A) 1/2 (B) 1/8 (C) 2 (D) 8

Description : If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection of the beam at the centre is changed by (A) 1/2 (B) 1/8 (C) 2 (D) 8

Last Answer : (A) 1/2

If the width b and depth d of a beam simply supported with a central load are interchanged, the deflection at the centre of the beam will be changed in the ratio of (A) b/d (B) d/b (C) (d/b)2 (D) (b/d)

Description : If the width b and depth d of a beam simply supported with a central load are interchanged, the  deflection at the centre of the beam will be changed in the ratio of  (A) b/d (B) d/b (C) (d/b)2 (D) (b/d)

Last Answer : (D) (b/d)2

For determining the ultimate bearing capacity of soil, the recommended size of a square bearing plate to be used in load plate test should be 30 to 75 cm square with a minimum thickness of (A) 5 mm (B) 10 mm (C) 15 mm (D) 25 mm

Description : For determining the ultimate bearing capacity of soil, the recommended size of a square bearing plate to be used in load plate test should be 30 to 75 cm square with a minimum thickness of (A) 5 mm (B) 10 mm (C) 15 mm (D) 25 mm

Last Answer : Answer: Option D

Pick up the incorrect statement from the following. While performing preliminary test on concrete (A) Proportions of the material and water should be the same as to be used at the work site (B) Cement should be mixed by hand in order to maintain uniformity (C) Concrete mix should be stored in air-tight containers (D) Concrete ingredients should be kept at a temperature of 37° ± 2°C

Description : Pick up the incorrect statement from the following. While performing preliminary test on concrete (A) Proportions of the material and water should be the same as to be used at the work site (B) ... in air-tight containers (D) Concrete ingredients should be kept at a temperature of 37° 2°C

Last Answer : Answer: Option D

Pick up the incorrect statement from the following. For performing compressive strength test of cement (A) Cement and standard sand mortar are used in the ratio of 1 : 3 (B) Water is added at the rate of (P/4) + 3.0 percentage of water where P is the percentage of water for standard consistency (C) A cube mould of 10 cm × 10 cm × 10 cm is used (D) The prepared moulds are kept in a atmosphere of 50% relative humidity

Description : Pick up the incorrect statement from the following. For performing compressive strength test of cement (A) Cement and standard sand mortar are used in the ratio of 1 : 3 (B) Water is added at the ... cm 10 cm is used (D) The prepared moulds are kept in a atmosphere of 50% relative humidity

Last Answer : Answer: Option A

Water to the consumers may be supplied from (A) Infiltration galleries connected to sump well (B) Infiltration well dug out on the banks of rivers (C) Ranney wells sunk to the water level (D) All the above

Description : Water to the consumers may be supplied from  (A) Infiltration galleries connected to sump well  (B) Infiltration well dug out on the banks of rivers  (C) Ranney wells sunk to the water level  (D) All the above 

Last Answer : (D) All the above 

In grillage foundations, distance between flanges of grillage beams, is kept (A) 40 cm (B) Equal to flange width (C) Twice the flange width (D) Maximum of (a), (b) and (c)

Description : In grillage foundations, distance between flanges of grillage beams, is kept (A) 40 cm (B) Equal to flange width (C) Twice the flange width (D) Maximum of (a), (b) and (c)

Last Answer : Answer: Option C

Pick up the correct specification of one-room quarters generally adopted from the following: (A) Six quarters in a row (B) The size of room is either 3.5 m × 3 m or 4.2 m × 2.5 m (C) The front verandah is kept 2 m wide (D) All the above

Description : Pick up the correct specification of one-room quarters generally adopted from the following: (A) Six quarters in a row (B) The size of room is either 3.5 m × 3 m or 4.2 m × 2.5 m (C) The front verandah is kept 2 m wide (D) All the above

Last Answer : Answer: Option D

The stem of a cantilever retaining wall which retains earth level with top is 6 m. If the angle of repose and weight of the soil per cubic metre are 30° and 2000 kg respectively, the effective width of the stem at the bottom, is (A) 51.5 (B) 52.5 (C) 53.5 (D) 54.5

Description : The stem of a cantilever retaining wall which retains earth level with top is 6 m. If the angle of repose and weight of the soil per cubic metre are 30° and 2000 kg respectively, the effective width of the stem at the bottom, is (A) 51.5 (B) 52.5 (C) 53.5 (D) 54.5

Last Answer : Answer: Option C

A metal plate with a circular hole at the centre is heated. What will happen to the area of the hole? (1) Increase (2) Decrease (3) Remain constant (4) Will increase first and then decrease

Description : A metal plate with a circular hole at the centre is heated. What will happen to the area of the hole? (1) Increase (2) Decrease (3) Remain constant (4) Will increase first and then decrease

Last Answer : (1) Increase Explanation: Assuming the disc is uniform and isotropic (the same in different directions), the hole will expand in the same ratio as the metal. It is because the thermal expansion equation ... is made out of metal. And if the circumference of the hole expands, so does the diameter.

A metal plate with a circular hole at the centre is heated. What will happen to the area of the hole?

Description : A metal plate with a circular hole at the centre is heated. What will happen to the area of the hole?

Last Answer : Decrease

A metal plate with a circular hole at the centre is heated. What will happen to the area of the hole ? (1) Increase (2) Dacrease (3) Remain constant (4) Will increase first and then dcrease

Description : A metal plate with a circular hole at the centre is heated. What will happen to the area of the hole ? (1) Increase (2) Dacrease (3) Remain constant (4) Will increase first and then dcrease

Last Answer : Increase

Pick up the incorrect statement from the following: (A) Lead is the average horizontal straight distance between the borrow pit and the place of spreading soil (B) The lead is calculated for each block of the excavated area (C) The unit of lead is 50 m for a distance upto 500 m (D) The unit of lead is 1 km where the lead exceeds 2 km

Description : Pick up the incorrect statement from the following: (A) Lead is the average horizontal straight distance between the borrow pit and the place of spreading soil (B) The lead is calculated for each block of the ... a distance upto 500 m (D) The unit of lead is 1 km where the lead exceeds 2 km

Last Answer : (D) The unit of lead is 1 km where the lead exceeds 2 km

The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of 4 tonnes at the centre. The maximum stress in the bottom most fibre at the mid span section, is (A) 13.33 kg/cm2 tensile (B) 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Last Answer : (C) 26.67 kg/cm2 tensile

Pick up the correct statement from the following: (A) If the ratio of depth to width is less than 2, it is shallow foundation (B) If the ratio of depth to width is more than 2, it is deep foundation (C) If the ratio of the length to width is between 1 and 2, it is spread foundation (D) All the above

Description : Pick up the correct statement from the following: (A) If the ratio of depth to width is less than 2, it is shallow foundation (B) If the ratio of depth to width is more than 2, it is deep ... the ratio of the length to width is between 1 and 2, it is spread foundation (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) Minimum desirable width of medians on rural highways is 5 metres (B) Minimum width of medians should be 3 metres (C) On long bridges and viaducts, the width of medians should be 1.5 m (D) All the above

Description : Pick up the correct statement from the following: (A) Minimum desirable width of medians on rural highways is 5 metres (B) Minimum width of medians should be 3 metres (C) On long bridges and viaducts, the width of medians should be 1.5 m (D) All the above

Last Answer : Answer: Option D

The discharge through a channel of trapezoidal section is maximum when (A) Width of channel at the top is equal to twice the width at the bottom (B) Depth of channel is equal to the width at the bottom (C) The sloping side is equal to half the width at the top (D) The sloping side is equal to the width at the bottom

Description : The discharge through a channel of trapezoidal section is maximum when (A) Width of channel at the top is equal to twice the width at the bottom (B) Depth of channel is equal to the width at the bottom ... equal to half the width at the top (D) The sloping side is equal to the width at the bottom

Last Answer : Answer: Option C

Pick up the correct specification of Ramsden eyepiece from the following: (A) It consists of two equal piano convex lenses (B) The curved surfaces of Plano-convex lenses face each other (C) The distance between the diaphragm and the front lens of the eyepiece is kept equal to 1/4 th of the focal length of a lens so that rays from a point on the diaphragm enter the eye as a parallel beam (D) All the above

Description : Pick up the correct specification of Ramsden eyepiece from the following:  (A) It consists of two equal piano convex lenses  (B) The curved surfaces of Plano-convex lenses face each other  (C) ... from a point on the diaphragm enter the eye as a  parallel beam  (D) All the above 

Last Answer : (D) All the above 

Consider the following statements: 1. The benefit of surcharge and depth of foundation is only marginal in case of footings on purely cohesive soils. 2. The bearing capacity of a footing in pure clay increases with increase in size of the footing. 3. Size effects in plate load tests are more important in case of cohesionless soils. Which of these statements are correct? (a) 1, 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only

Description : Consider the following statements: 1. The benefit of surcharge and depth of foundation is only marginal in case of footings on purely cohesive soils. 2. The bearing capacity of a footing in pure clay increases with increase in size of the ... , 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only

Last Answer : (d) 1 & 3 only

The intake opening is generally covered by a screen to prevent entry of debris etc. and its level is kept (A) At the level of water of the source (B) At the bottom of water of the source (C) At about 2.5 m above the bottom (D) None of these

Description : The intake opening is generally covered by a screen to prevent entry of debris etc. and its level is  kept  (A) At the level of water of the source  (B) At the bottom of water of the source  (C) At about 2.5 m above the bottom  (D) None of these 

Last Answer : (C) At about 2.5 m above the bottom 

The intake opening is generally covered by a screen to prevent entry of debris etc. and its level is kept (A) At the level of water of the source (B) At the bottom of water of the source (C) At about 2.5 m above the bottom (D) None of these

Description : The intake opening is generally covered by a screen to prevent entry of debris etc. and its level is kept (A) At the level of water of the source (B) At the bottom of water of the source (C) At about 2.5 m above the bottom (D) None of these

Last Answer : (C) At about 2.5 m above the bottom

Pick up the correct statement from the following: (A) Index of wetness = actual rainfall in a year at a place/normal rainfall of that place (B) Normal annual rainfall is obtained by taking the mean of the annual rainfall over a period of 35 years (C) Index of wetness gives an idea of the wetness of the year (D) All the above

Description : Pick up the correct statement from the following: (A) Index of wetness = actual rainfall in a year at a place/normal rainfall of that place (B) Normal annual rainfall is obtained by taking the mean of the ... years (C) Index of wetness gives an idea of the wetness of the year (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) The estimated value of the work excluding the amount for contingencies, work charged establishment, tool and plants, is called work value (B) The actual expenditure involved to complete a work including incidental, establishment and travelling charges, is called actual cost (C) The formal acceptance by the administrative department for incurring an expenditure on the work, is called administrative approval (D) All the above

Description : Pick up the correct statement from the following: (A) The estimated value of the work excluding the amount for contingencies, work charged establishment, tool and plants, is called work value (B ... for incurring an expenditure on the work, is called administrative approval (D) All the above

Last Answer : (D) All the above