The chaining on sloping ground is (A) Easier along the falling gradient (B) Easier along the up gradient (C) Equally convenient along falling as well as up gradient (D) All the above

The chaining on sloping ground is
(A) Easier along the falling gradient
(B) Easier along the up gradient
(C) Equally convenient along falling as well as up gradient
(D) All the above
by

1 Answer

Answer :

(A) Easier along the falling gradient
by

Related questions

Describe stepping method of chaining on sloping ground.

Description : Describe stepping method of chaining on sloping ground.

Last Answer : 1. If A and B are the two points on sloping ground, for which horizontal distance is to be measured. 2. Unfold the chain. By touching handle to station A, stretch it up to maximum possible ... 6. Thus total horizontal distance on sloping ground is calculated as d(AB) = L1+L2+L3 in meters.

Explain Direct method of chaining on sloping ground with neat skeetch.

Description : Explain Direct method of chaining on sloping ground with neat skeetch. 

Last Answer : While chaining on sloping ground, the horizontal distances can be computed by direct method i.e. By stepping. By stepping: It consist in measuring the distance in small horizontal lengths (e.g.L1). Let ... is continued in the correct line with point B. Then length of line AB=L1 +L2 +L3+L4

Explain with neat sketch method of stepping of chaining on sloping ground.

Description : Explain with neat sketch method of stepping of chaining on sloping ground.

Last Answer : Procedure : To measure the horizontal distance between points A & B on sloping ground following steps should be followed ( Refer above figure.) 1. Starting from point A, the chain is unfolded and ... . Finally calculate total chained distance as d(AB) = d(AP1) + d(P2P3) + d(P4P5)

Explain the process of chaining on sloping ground by stepping method with neat sketch.

Description : Explain the process of chaining on sloping ground by stepping method with neat sketch.

Last Answer : The procedure to measure horizontal distance between the points A and B on sloping ground is as follows. 1. Two persons-leader and follower are required for chaining. 2. The follower holds the end of chain at A. The leader goes ... between A and b L = AM, + MN' + NO' + OP' + PQ' + QB'

Describe in brief process of chaining on sloping ground.

Description : Describe in brief process of chaining on sloping ground.

Last Answer : In direct method which is also known as stepping method horizontal distance is directly measured as shown in fig. Horizontal distance between A and B is required to be measured. Procedure: i) A ... iii) The next step start from the C and the method is continued till point B reached. 

The ground surface slopes 1 in 50 along a proposed railway embankment 150 m in length. The height of the embankment at zero chainage is 0.5 m, the width is 11 m and side slopes 2:1. If the falling gradient of the embankment is 1 in 150, the quantity of the earthwork calculated by Prismoidal formula, is (A) 3250 m3 (B) 3225 m3 (C) 3275 m3 (D) 3300 m3

Description : The ground surface slopes 1 in 50 along a proposed railway embankment 150 m in length. The height of the embankment at zero chainage is 0.5 m, the width is 11 m and side slopes 2:1. If the falling gradient ... calculated by Prismoidal formula, is (A) 3250 m3 (B) 3225 m3 (C) 3275 m3 (D) 3300 m3

Last Answer : (B) 3225 m3

If the chain line which runs along N-S direction is horizontal and the ground in E-W direction is sloping (A) It is possible to set offsets correctly on east side (B) It is possible to set offsets correctly on east side (C) It is not possible to set offsets correctly on west side (D) It is possible to set offsets correctly on both sides

Description : If the chain line which runs along N-S direction is horizontal and the ground in E-W direction is sloping (A) It is possible to set offsets correctly on east side (B) It is possible to ... possible to set offsets correctly on west side (D) It is possible to set offsets correctly on both sides

Last Answer : (D) It is possible to set offsets correctly on both sides

Pick up the incorrect statement from the following: (A) As a wave of sea water approaches the coast line, it is generally accompanied by a drift of water in the direction of wave advance (B) The on-shore wind helps to produce wave action as well as rise of M.S.L. (C) A falling hydraulic gradient occurs in the direction of the wave (D) The wave while receding carries finer particles out to deep water

Description : Pick up the incorrect statement from the following: (A) As a wave of sea water approaches the coast line, it is generally accompanied by a drift of water in the direction of wave advance (B) ... in the direction of the wave (D) The wave while receding carries finer particles out to deep water

Last Answer : (C) A falling hydraulic gradient occurs in the direction of the wave

While measuring a chain line between two stations and intervened by a raised ground (A) Vision gets obstructed (B) Chaining gets obstructed (C) Both vision and chaining get obstructed (D) All the above

Description : While measuring a chain line between two stations and intervened by a raised ground (A) Vision gets obstructed (B) Chaining gets obstructed (C) Both vision and chaining get obstructed (D) All the above

Last Answer : (A) Vision gets obstructed

Pick up the correct statement from the following: (A) Cavity of a cavity wall should start near ground level (B) Cavity of a cavity wall should terminate near eaves level of sloping roof (C) Cavity of a cavity wall should terminate near coping of flat roof with parapet wall (D) All the above

Description : Pick up the correct statement from the following: (A) Cavity of a cavity wall should start near ground level (B) Cavity of a cavity wall should terminate near eaves level of sloping roof (C) Cavity of a cavity wall should terminate near coping of flat roof with parapet wall (D) All the above

Last Answer : Answer: Option D

Poincare said: “To doubt everything or to believe everything are two equally convenient solutions; both dispense with the necessity of reflection.” Which way do you lean and why?

Description : Poincare said: “To doubt everything or to believe everything are two equally convenient solutions; both dispense with the necessity of reflection.” Which way do you lean and why?

Last Answer : My inclinations lie with yours, but it seems as though what Poincare was getting at is that to give in to either sensibility is to take the easy way out.

If h1 and h2 are the differences in level between ground and the formation levels, m is the slope of the sloping sides. D is the distance between the cross sections then, Prismoidal correction for a level section is (A) D/2m(h1 - h2) (B) D/3m(h1 - h2) (C) D/6m(h1 - h2)2(D) D/6m(h1 - h2)3

Description : If h1 and h2 are the differences in level between ground and the formation levels, m is the slope of the sloping sides. D is the distance between the cross sections then, Prismoidal correction for a level section is (A) D/2m(h1 - h2) (B) D/3m(h1 - h2) (C) D/6m(h1 - h2)2 (D) D/6m(h1 - h2)3

Last Answer : (C) D/6m(h1 - h2)2

The gradients of trace cuts for hilly roads, are kept (A) Equal to ruling gradient (B) 10 to 20 per cent easier than ruling gradients (C) 10 to 20 per cent steeper than ruling gradients (D) None of these

Description : The gradients of trace cuts for hilly roads, are kept (A) Equal to ruling gradient (B) 10 to 20 per cent easier than ruling gradients (C) 10 to 20 per cent steeper than ruling gradients (D) None of these

Last Answer : Answer: Option B

In a square beam loaded longitudinally, shear develops (A) On middle fibre along horizontal plane (B) On lower fibre along horizontal plane (C) On top fibre along vertical plane (D) Equally on each fibre along horizontal plane

Description : In a square beam loaded longitudinally, shear develops (A) On middle fibre along horizontal plane (B) On lower fibre along horizontal plane (C) On top fibre along vertical plane (D) Equally on each fibre along horizontal plane

Last Answer : (D) Equally on each fibre along horizontal plane (D) Equally on each fibre along horizontal plane

The dry-bulb temperature scale is read on a psychrometric chart along the: a. Left vertical axis b. Right vertical axis c. Saturation line and sloping downward to the right d. Top horizontal axis e. Horizontal axis on the bottom of the chart

Description : The dry-bulb temperature scale is read on a psychrometric chart along the: a. Left vertical axis b. Right vertical axis c. Saturation line and sloping downward to the right d. Top horizontal axis e. Horizontal axis on the bottom of the chart

Last Answer : ANSWER : E

Which of the following statements is true? a. It is usually easier for the auditor to uncover irregularities than errors. b. It is usually easier for the auditor to uncover errors than irregularities. c. It is usually equally difficult for the auditor to uncover errors or irregularities. d. Usually, none of the given statements is true

Description : Which of the following statements is true? a. It is usually easier for the auditor to uncover irregularities than errors. b. It is usually easier for the auditor to uncover errors than ... the auditor to uncover errors or irregularities. d. Usually, none of the given statements is true

Last Answer : It is usually easier for the auditor to uncover errors than irregularities

Which of the following statements is true? a. It is usually equally difficult for the auditor to uncover errors or irregularities. b. It is usually easier for the auditor to uncover irregularities than errors. c. It is usually easier for the auditor to uncover errors than irregularities. d. Usually, none of the above statements is true.

Description : Which of the following statements is true? a. It is usually equally difficult for the auditor to uncover errors or irregularities. b. It is usually easier for the auditor to uncover irregularities ... auditor to uncover errors than irregularities. d. Usually, none of the above statements is true.

Last Answer : It is usually easier for the auditor to uncover errors than irregularities.

Pick up the correct statement from the following regarding the pressure conduits: (A) Pressure conduits are permitted to run ¾th full (B) Pressure conduits are always laid along down grades (C) The hydraulic gradient line always coincides the invert of the conduit (D) None of these

Description : Pick up the correct statement from the following regarding the pressure conduits:  (A) Pressure conduits are permitted to run ¾th full  (B) Pressure conduits are always laid along down grades  ... ) The hydraulic gradient line always coincides the invert of the conduit  (D) None of these

Last Answer : (D) None of these

The reduced levels of points, 30 metres apart along the longitudinal section of a road portion between chainages 5 and 9 are shown in the given figure. If there is a uniform up-gradient of the road 120 in 1, the chainage of the point with no filling or cutting is (A) (6 + 15) chains (B) (6 + 12) chains (C) (6 + 18) chains (D) None of these

Description : The reduced levels of points, 30 metres apart along the longitudinal section of a road portion between chainages 5 and 9 are shown in the given figure. If there is a uniform up-gradient of the road 120 in 1, the chainage ... 15) chains (B) (6 + 12) chains (C) (6 + 18) chains (D) None of these

Last Answer : (B) (6 + 12) chains

In active state of plastic equilibrium in a non cohesive soil with horizontal ground surface (A) Major principal stress is horizontal (B) Minor principal stress is vertical (C) Major principal stress is vertical (D) Minor and major principal stresses are equally inclined to horizontal

Description : In active state of plastic equilibrium in a non cohesive soil with horizontal ground surface (A) Major principal stress is horizontal (B) Minor principal stress is vertical (C) Major principal stress is vertical (D) Minor and major principal stresses are equally inclined to horizontal

Last Answer : Answer: Option C

Explain the Stepping method of measuring the horizontal distance of sloping ground with sketch.

Description : Explain the Stepping method of measuring the horizontal distance of sloping ground with sketch. 

Last Answer : In direct method which is also known as stepping method, horizontal distance is directly measured as shown in fig. Stepping Method Horizontal distance between A and B is required to be measured. Procedure ... next step starts from the C and the method is continued till point B reached. 

The slope correction for a length of 30 m along a gradient of 1 in 20, is (A) 3.75 cm (B) 0.375 cm (C) 37.5 cm (D) 2.75 cm

Description : The slope correction for a length of 30 m along a gradient of 1 in 20, is  (A) 3.75 cm  (B) 0.375 cm  (C) 37.5 cm  (D) 2.75 cm

Last Answer : (A) 3.75 cm 

A sewer is laid from a manhole to a manhole , 250 m away along a gradient of 1 in 125. If the reduced level of the invert at is 205.75 m and the height of the boning rod is 3 m, the reduced level of the sight rail at , is (A) 208.75 m (B) 202.75 m (C) 206.75 m (D) 211.75 m

Description : A sewer is laid from a manhole to a manhole , 250 m away along a gradient of 1 in 125. If the  reduced level of the invert at is 205.75 m and the height of the boning rod is 3 m, the reduced  level of the sight rail at , is  (A) 208.75 m  (B) 202.75 m  (C) 206.75 m  (D) 211.75 m

Last Answer : (C) 206.75 m 

If x% is the gradient of an alignment and y% is the gradient after proper super-elevation along a curved portion of a highway, the differential grade along the curve, is (A) (x + y) % (B) (x - y) % (C) (y - x) % (D) (y + x) %

Description : If x% is the gradient of an alignment and y% is the gradient after proper super-elevation along a curved portion of a highway, the differential grade along the curve, is (A) (x + y) % (B) (x - y) % (C) (y - x) % (D) (y + x) %

Last Answer : Answer: Option C

If the elevations along a road increase, the slope of the road along the longitudinal direction, is known as (A) Gradient (B) Grade (C) Positive grade (D) Negative grade

Description : If the elevations along a road increase, the slope of the road along the longitudinal direction, is known as (A) Gradient (B) Grade (C) Positive grade (D) Negative grade

Last Answer : Answer: Option A

To compensate the loss of tractive force of vehicles along curves of radius R, the percentage reduction of gradient, is (A) 50/R (B) 75/R (C) 100/R (D) 125/R

Description : To compensate the loss of tractive force of vehicles along curves of radius R, the percentage reduction of gradient, is (A) 50/R (B) 75/R (C) 100/R (D) 125/R

Last Answer : Answer: Option B

Gradient resistance of moving vehicles along down slopes, is (A) + 7 kg/tonne (B) + 9 kg/tonne (C) - 9 kg/tonne (D) - 7 kg/tonne

Description : Gradient resistance of moving vehicles along down slopes, is (A) + 7 kg/tonne (B) + 9 kg/tonne (C) - 9 kg/tonne (D) - 7 kg/tonne

Last Answer : Answer: Option C

A gradient along which the vehicle does not require any tractive effort to maintain a specified speed, is known as (A) Ruling gradient (B) Pushing gradient (C) Floating gradient (D) Minimum gradient

Description : A gradient along which the vehicle does not require any tractive effort to maintain a specified speed, is known as (A) Ruling gradient (B) Pushing gradient (C) Floating gradient (D) Minimum gradient

Last Answer : Answer: Option C

Keeping the instrument height as 1½ m, length of staff 4 m, the up gradient of the ground 1 in 10, the sight on the up slope must be less than (A) 25 cm (B) 20 m (C) 45 m (D) 10 m

Description : Keeping the instrument height as 1½ m, length of staff 4 m, the up gradient of the ground 1 in 10,  the sight on the up slope must be less than  (A) 25 cm  (B) 20 m  (C) 45 m  (D) 10 m

Last Answer : (C) 45 m 

An imaginary line lying throughout the surface of ground and preserving a constant inclination to the horizontal is known as (A) Contour line (B) Horizontal equivalent (C) Contour interval (D) Contour gradient

Description : An imaginary line lying throughout the surface of ground and preserving a constant inclination to the horizontal is known as (A) Contour line (B) Horizontal equivalent (C) Contour interval (D) Contour gradient

Last Answer : (D) Contour gradient

If the viscosity of ground water is 1.00, the Slitcher's constant is 400, the effective size of soil particles in aquifer is 0.5 mm and hydraulic gradient is 1 in 80, the velocity of flow is (A) 0.25 m/day (B) 0.50 m/day (C) 1.00 m/day (D) 1.25 m/day

Description : If the viscosity of ground water is 1.00, the Slitcher's constant is 400, the effective size of soil particles in aquifer is 0.5 mm and hydraulic gradient is 1 in 80, the velocity of flow is (A) 0.25 m/day (B) 0.50 m/day (C) 1.00 m/day (D) 1.25 m/day

Last Answer : Answer: Option D

If the formation level of a highway has a uniform gradient for a particular length, and the ground is also having a longitudinal slope, the earthwork may be calculated by (A) Mid-section formula (B) Trapezoidal formula (C) Prismoidal formula (D) All the above

Description : If the formation level of a highway has a uniform gradient for a particular length, and the ground is also having a longitudinal slope, the earthwork may be calculated by (A) Mid-section formula (B) Trapezoidal formula (C) Prismoidal formula (D) All the above

Last Answer : (D) All the above

Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's law is equally applicable to concrete as well as to steel (C) Variation of stress in reinforcement due to changes in external loading is negligible (D) All the above

Description : Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's ... of stress in reinforcement due to changes in external loading is negligible (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C) Curing of concrete is done for proper compaction of cement (D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Description : Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C ... D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Last Answer : Option D

If you get an opportunity to teach a visually challenged student along with normal students, what type of treatment would you like to give him in the class ? (A) Not giving extra attention because majority may suffer. (B) Take care of him sympathetically in the class- room. (C) You will think that blindness is his destiny and hence you cannot do anything. (D) Arrange a seat in the front row and try to teach at a pace convenient to him.

Description : If you get an opportunity to teach a visually challenged student along with normal students, what type of treatment would you like to give him in the class ? (A) Not giving extra attention because majority may ... (D) Arrange a seat in the front row and try to teach at a pace convenient to him.

Last Answer : (D) Arrange a seat in the front row and try to teach at a pace convenient to him.

Pick up the correct statement from the following: (A) With both handles in his left hand, the chain man throws out the chain with his right hand and the second chain man assists him to free it from knots (B) The follower of the chaining operation should be more experienced than the leader (C) At the end of the tenth chain length, the two chain men meet and the ten arrows are handed over to the leader (D) All the above

Description : Pick up the correct statement from the following: (A) With both handles in his left hand, the chain man throws out the chain with his right hand and the second chain man assists him to free it from ... the two chain men meet and the ten arrows are handed over to the leader (D) All the above

Last Answer : (D) All the above

Rising gradient followed by a falling gradient is known as a) Rulling gradient b) Momentum gradient* c) Pusher graient d) Aangular gradient

Description : Rising gradient followed by a falling gradient is known as a) Rulling gradient b) Momentum gradient* c) Pusher graient d) Aangular gradient

Last Answer : b) Momentum gradient

Greater accuracy in linear measurements, is obtained by (A) Tacheometry (B) Direct chaining (C) Direct taping (D) All the above

Description : Greater accuracy in linear measurements, is obtained by (A) Tacheometry (B) Direct chaining (C) Direct taping (D) All the above

Last Answer : (C) Direct taping

The instrument which is used in plane tabling for obtaining horizontal and vertical distances directly without resorting to chaining, is known as (A) Plane alidade (B) Telescopic alidade (C) Clinometer (D) Tacheometer

Description : The instrument which is used in plane tabling for obtaining horizontal and vertical distances directly without resorting to chaining, is known as (A) Plane alidade (B) Telescopic alidade (C) Clinometer (D) Tacheometer

Last Answer : (B) Telescopic alidade

Back fill with a sloping surface exerts a total active pressure Pa on the wall of height H and acts at (A) H/4 above the base parallel to base (B) H/2 above the base parallel to base (C) H/3 above the base parallel to base (D) H/5 above the base parallel to base

Description : Back fill with a sloping surface exerts a total active pressure Pa on the wall of height H and acts at (A) H/4 above the base parallel to base (B) H/2 above the base parallel to base (C) H/3 above the base parallel to base (D) H/5 above the base parallel to base

Last Answer : Answer: Option C

The discharge through a channel of trapezoidal section is maximum when (A) Width of channel at the top is equal to twice the width at the bottom (B) Depth of channel is equal to the width at the bottom (C) The sloping side is equal to half the width at the top (D) The sloping side is equal to the width at the bottom

Description : The discharge through a channel of trapezoidal section is maximum when (A) Width of channel at the top is equal to twice the width at the bottom (B) Depth of channel is equal to the width at the bottom ... equal to half the width at the top (D) The sloping side is equal to the width at the bottom

Last Answer : Answer: Option C

The most economical section of a trapezoidal channel is one which has hydraulic mean depth equal to (A) 1/2 × depth (B) 1/2 × breadth (C) 1/2 × sloping side (D) 1/4 × (depth + breadth)

Description : The most economical section of a trapezoidal channel is one which has hydraulic mean depth equal to (A) 1/2 × depth (B) 1/2 × breadth (C) 1/2 × sloping side (D) 1/4 × (depth + breadth)

Last Answer : Answer: Option A

The drain which is provided parallel to roadway to intercept and divert the water from hill slopes is known as (A) Sloping drain (B) Catch-water drain (C) Side drain (D) Cross drain

Description : The drain which is provided parallel to roadway to intercept and divert the water from hill slopes is known as (A) Sloping drain (B) Catch-water drain (C) Side drain (D) Cross drain

Last Answer : Answer: Option B

Bituminous fells are used for (A) Covering A.C. sheets (B) Covering sloping roofs (C) D.P.C. (D) None to these

Description : Bituminous fells are used for (A) Covering A.C. sheets (B) Covering sloping roofs (C) D.P.C. (D) None to these

Last Answer : Answer: Option A

The line of intersection of the surfaces of a sloping roof forming an external angle exceeding 180°, is (A) Ridge (B) Hip (C) Valley (D) None of these

Description : The line of intersection of the surfaces of a sloping roof forming an external angle exceeding 180°, is (A) Ridge (B) Hip (C) Valley (D) None of these

Last Answer : Answer: Option B

The window which is provided on a sloping roof of a building, is called (A) Lantern window (B) Dormer window (C) Louvered window (D) Rash window

Description : The window which is provided on a sloping roof of a building, is called (A) Lantern window (B) Dormer window (C) Louvered window (D) Rash window

Last Answer : Answer: Option B

The opening provided in sloping roof with its top parallel to the roof surface, is called (A) Dormer window (B) Sky light window (C) Lantern window (D) Louvered window

Description : The opening provided in sloping roof with its top parallel to the roof surface, is called (A) Dormer window (B) Sky light window (C) Lantern window (D) Louvered window

Last Answer : Answer: Option B

The highest line of sloping roof, where two opposite slopes meet, is known as (A) Rafter (B) Ridge (C) Crown (D) Eave

Description : The highest line of sloping roof, where two opposite slopes meet, is known as (A) Rafter (B) Ridge (C) Crown (D) Eave

Last Answer : Answer: Option B

The line of intersection of two surfaces of a sloping roof forming an internal angle less than 180°, is known as (A) Ridge (B) Hip (C) Valley (D) None of these

Description : The line of intersection of two surfaces of a sloping roof forming an internal angle less than 180°, is known as (A) Ridge (B) Hip (C) Valley (D) None of these

Last Answer : Answer: Option C

The members which support covering material of a sloping roof, are (A) Rafters (B) Purlins (C) Battens (D) Struts

Description : The members which support covering material of a sloping roof, are (A) Rafters (B) Purlins (C) Battens (D) Struts

Last Answer : Answer: Option A