The instrument which is used in plane tabling for obtaining horizontal and vertical distances directly without resorting to chaining, is known as (A) Plane alidade (B) Telescopic alidade (C) Clinometer (D) Tacheometer

The instrument which is used in plane tabling for obtaining horizontal and vertical distances
directly without resorting to chaining, is known as
(A) Plane alidade
(B) Telescopic alidade
(C) Clinometer
(D) Tacheometer
by

1 Answer

Answer :

(B) Telescopic alidade
by

Related questions

One of the Lehmann's rules of plane tabling, is (A) Location of the instrument station is always distant from each of the three rays from the known points in proportion to their distances (B) When looking in the direction of each of the given points, the instrument station will be on the right side of one and left side of the other ray (C) When the instrument station is outside the circumscribing circle its location is always on the opposite side of the ray to the most distant point as the inter-section of the other two rays (D) None of these

Description : One of the Lehmann's rules of plane tabling, is  (A) Location of the instrument station is always distant from each of the three rays from the  known points in proportion to their distances  ( ... to the most distant point as the inter-section of the other two rays  (D) None of these 

Last Answer : (A) Location of the instrument station is always distant from each of the three rays from the  known points in proportion to their distances 

State two advantages of telescopic alidade over simple alidade.

Description : State two advantages of telescopic alidade over simple alidade.

Last Answer : Advantages of telescopic alidade : i) Telescopic alidade is more accurate in bisection than simple alidade ii) Telescopic alidade is useful in comparatively longer range objects. iii) It can be easily ... is not possible by simple alidade. iv) It gives quicker bisection which saves time ultimately.

What is advantage of wing telescopic alidade?

Description : What is advantage of wing telescopic alidade?

Last Answer : Advantage of wing telescopic alidade is as follows 1. The range of sight is more 2. Accurate bisection 3. Inclined line of sight is possible 4. Horizontal distance can be calculated using stadia hairs. 5. Quick levelling is possible due to circular bubble tube as compared to dumpy level.

If the plane table is not horizontal in a direction at right angles to the alidade, the line of sight is parallel to the fiducial edge only for (A) Horizontal sights (B) Inclined sights upward (C) Inclined sight downward (D) None of these

Description : If the plane table is not horizontal in a direction at right angles to the alidade, the line of sight is parallel to the fiducial edge only for (A) Horizontal sights (B) Inclined sights upward (C) Inclined sight downward (D) None of these

Last Answer : (A) Horizontal sights

The instrument used for accurate centering in plane table survey is (A) Spirit level (B) Alidade (C) Plumbing fork (D) Trough compass

Description : The instrument used for accurate centering in plane table survey is (A) Spirit level (B) Alidade (C) Plumbing fork (D) Trough compass

Last Answer : (C) Plumbing fork

Subtense bar is an instrument used for (A) Levelling (B) Measurement of horizontal distances in plane areas (C) Measurement of horizontal distances in undulated areas (D) Measurement of angles

Description : Subtense bar is an instrument used for (A) Levelling (B) Measurement of horizontal distances in plane areas (C) Measurement of horizontal distances in undulated areas (D) Measurement of angles

Last Answer : (C) Measurement of horizontal distances in undulated areas

The method of plane tabling commonly used for establishing the instrument station is a method of (a) Radiation (b) Intersection* (c) Resection (d) Traversing

Description : The method of plane tabling commonly used for establishing the instrument station is a method of (a) Radiation (b) Intersection* (c) Resection (d) Traversing

Last Answer : (b) Intersection*

Which one of the following procedures for getting accurate orientation is the most distinctive feature of the art of plane tabling? (A) Radiation (B) Intersection (C) Traversing (D) Resection

Description : Which one of the following procedures for getting accurate orientation is the most distinctive feature of the art of plane tabling? (A) Radiation (B) Intersection (C) Traversing (D) Resection

Last Answer : (D) Resection

While surveying a plot of land by plane tabling, the field observations (A) And plotting proceed simultaneously (B) And plotting do not proceed simultaneously (C) And recorded in field books to be plotted later (D) All the above

Description : While surveying a plot of land by plane tabling, the field observations (A) And plotting proceed simultaneously (B) And plotting do not proceed simultaneously (C) And recorded in field books to be plotted later (D) All the above

Last Answer : (A) And plotting proceed simultaneously

State the use of alidade in plane table surveying

Description : State the use of alidade in plane table surveying

Last Answer : 1) It is used for sighting the objects to be located.  2) It is used for drawing the rays. 

Which of the instruments is not used in Preliminary survey. (a) Theodelite (b) Tacheometer (c) Dumpy level (d) Plane table (e) None of them*

Description : Which of the instruments is not used in Preliminary survey. (a) Theodelite (b) Tacheometer (c) Dumpy level (d) Plane table (e) None of them*

Last Answer : (e) None of them*

While rotating the theodolite in the horizontal plane, the bubble of the bubble tube takes up the same position in its tube, it indicates (A) The rotation axis is vertical (B) The trunnion axis is horizontal (C) The line of collimation is perpendicular to vertical axis (D) None of the above

Description : While rotating the theodolite in the horizontal plane, the bubble of the bubble tube takes up the  same position in its tube, it indicates  (A) The rotation axis is vertical  (B) The trunnion ... (C) The line of collimation is perpendicular to vertical axis  (D) None of the above

Last Answer : (A) The rotation axis is vertical

In a square beam loaded longitudinally, shear develops (A) On middle fibre along horizontal plane (B) On lower fibre along horizontal plane (C) On top fibre along vertical plane (D) Equally on each fibre along horizontal plane

Description : In a square beam loaded longitudinally, shear develops (A) On middle fibre along horizontal plane (B) On lower fibre along horizontal plane (C) On top fibre along vertical plane (D) Equally on each fibre along horizontal plane

Last Answer : (D) Equally on each fibre along horizontal plane (D) Equally on each fibre along horizontal plane

In the triaxial compression test, the application of additional axial stress (i.e. deviator stress) on the soil specimen produces shear stress on (A) Horizontal plane only (B) Vertical plane only (C) Both horizontal and vertical planes (D) All planes except horizontal and vertical planes

Description : In the triaxial compression test, the application of additional axial stress (i.e. deviator stress) on the soil specimen produces shear stress on (A) Horizontal plane only (B) Vertical plane only (C) Both horizontal and vertical planes (D) All planes except horizontal and vertical planes

Last Answer : (D) All planes except horizontal and vertical planes

A cylindrical specimen of saturated soil failed under an axial vertical stress of 100kN/m² when it was laterally unconfmed. The failure plane was inclined to the horizontal plane at an angle of 45°. The values of cohesion and angle of internal friction for the soil are respectively (A) 0.5 N/mm² and 30° (B) 0.05 N/mm² and 0° (C) 0.2 N/mm² and 0° (D) 0.05 N/mm² and 45°

Description : A cylindrical specimen of saturated soil failed under an axial vertical stress of 100kN/m² when it was laterally unconfmed. The failure plane was inclined to the horizontal plane at an angle of 45°. The values of cohesion and angle of ... N/mm² and 0° (C) 0.2 N/mm² and 0° (D) 0.05 N/mm² and 45°

Last Answer : Answer: Option B

Rankine's theory of active earth pressure assumes (A) Soil mass is homogeneous, dry and cohesionless (B) Ground surface is a plane which may be horizontal or inclined (C) Back of the wall is vertical and smooth (D) All the above

Description : Rankine's theory of active earth pressure assumes (A) Soil mass is homogeneous, dry and cohesionless (B) Ground surface is a plane which may be horizontal or inclined (C) Back of the wall is vertical and smooth (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) When the electric field oscillates in the direction of the electric vector, a plane polarised wave is formed (B) When the electric vector is in the plane of incidence, vertical polarisation is formed (C) When the electric vector is at right angles to the plane of incidence, horizontal polarization wave is formed (D) All of these

Description : Pick up the correct statement from the following: (A) When the electric field oscillates in the direction of the electric vector, a plane polarised wave is formed (B) When the electric vector is ... right angles to the plane of incidence, horizontal polarization wave is formed (D) All of these

Last Answer : Answer: Option D

The angle of repose of a soil is the maximum angle which the outer face of the soil mass makes (A) With the horizontal (B) With the vertical (C) With the perpendicular to the inclined plane of the soil (D) None of these

Description : The angle of repose of a soil is the maximum angle which the outer face of the soil mass makes (A) With the horizontal (B) With the vertical (C) With the perpendicular to the inclined plane of the soil (D) None of these

Last Answer : Answer: Option A

The total pressure force on a plane area is equal to the area multiplied by the intensity of pressure at the Centroid, if (A) The area is horizontal (B) The area is vertical (C) The area is inclined (D) All of the above

Description : The total pressure force on a plane area is equal to the area multiplied by the intensity of pressure at the Centroid, if (A) The area is horizontal (B) The area is vertical (C) The area is inclined (D) All of the above

Last Answer : Answer: Option D

Tabling process used for separating two materials of different densities by passing the dilute pulp over a table/deck, which is inclined from the horizontal surface at an angle of about (A) 1 to 2° (B) 2 to 5° (C) 5 to 10° (D) 10 to 15°

Description : Tabling process used for separating two materials of different densities by passing the dilute pulp over a table/deck, which is inclined from the horizontal surface at an angle of about (A) 1 to 2° (B) 2 to 5° (C) 5 to 10° (D) 10 to 15°

Last Answer : (B) 2 to 5°

The area of any irregular figure of the plotted map is measured with (A) Pentagraph (B) Sextant (C) Clinometer (D) Planimeter

Description : The area of any irregular figure of the plotted map is measured with (A) Pentagraph (B) Sextant (C) Clinometer (D) Planimeter

Last Answer : (D) Planimeter

A clinometer is used for (A) Measuring angle of slope (B) Correcting line of collimation (C) Setting out right angles (D) Defining natural features

Description : A clinometer is used for (A) Measuring angle of slope (B) Correcting line of collimation (C) Setting out right angles (D) Defining natural features

Last Answer : (A) Measuring angle of slope

ECE Board Exam March 1996 LORAN is a navigation system used primarily for A. approach control B. obtaining fixes over large distances C. blind landing D. automatic collision warning

Description : ECE Board Exam March 1996 LORAN is a navigation system used primarily for A. approach control B. obtaining fixes over large distances C. blind landing D. automatic collision warning

Last Answer : B. obtaining fixes over large distances

ECE Board Exam March 1996 LORAN is a navigational system used primarily for _____________. A. blind landing B. obtaining your fixes location over large distances C. automatic collision warning D. approach control

Description : ECE Board Exam March 1996 LORAN is a navigational system used primarily for _____________. A. blind landing B. obtaining your fixes location over large distances C. automatic collision warning D. approach control

Last Answer : B. obtaining your fixes location over large distances

Write any four advantages of intersection method of plane tabling over radiation method of plane tabling.

Description : Write any four advantages of intersection method of plane tabling over radiation method of plane tabling.

Last Answer : Advantages of intersection method: 1. Interection method requires less ground distance measurement than radiation method. 2. By this method we can locate inaccessible points which cannot be ... to radiation method, intersection method eliminates undulation error, bisection error and plotting errors.

Explain errors occurred due to manipulation and sighting in plane tabling.

Description : Explain errors occurred due to manipulation and sighting in plane tabling.

Last Answer : i) The board not being horizontal- This error affects chiefly the measurement of vertical angles. ii) The table not being accurately centered. The plotted position of the occupied station not ... and correct any displacement. v) The defective sighting- The object not being correctly sighted.

Define orientation and principle of plane tabling.

Description : Define orientation and principle of plane tabling. 

Last Answer : Orientation: The orientation of plane table means keeping the plane table at all stations parallel to the position it occupied at first station. Principles of plane table survey: 1. The rays drawn from ... same as that of previous station i.e. orientation should be done at each changed station.  

Enlist the methods of plane tabling.

Description : Enlist the methods of plane tabling. 

Last Answer : Method of Surveying with the plane table are : 1) Radiation 2) Intersection 3) Traversing 4) Resection

Explain with neat sketch the procedure of radiation method of plane tabling.

Description : Explain with neat sketch the procedure of radiation method of plane tabling.

Last Answer : 1. The table is set at suitable station e.g. P from where all stations can be sighted and measured. 2. After centering and leveling, mark station P as P' on sheet. 3. Suppose stations A, B, C, and D are ... marked as pa. 5. Similarly station B, C and D are bisected and marked as b, c and d.

What are the sources of errors in plane tabling?

Description : What are the sources of errors in plane tabling?

Last Answer : The following are the sources of errors in plane tabling 1) The board not being horizontal 2) The table not being accurately centered 3) The table not being Correctly oriented 4) The objects ... through the station point 7) Inaccuracy in plotting 8) The expansion and contraction of the paper 

Pick up the correct statement from the following: (A) Continuous grading is not necessary for obtaining a minimum of air voids (B) The omission of a certain size of aggregate is shown by a straight horizontal line on the grading curve (C) The omission of a certain size of aggregate in concrete increases the workability but also increases the liability to segregation (D) All the above

Description : Pick up the correct statement from the following: (A) Continuous grading is not necessary for obtaining a minimum of air voids (B) The omission of a certain size of aggregate is shown by ... in concrete increases the workability but also increases the liability to segregation (D) All the above

Last Answer : Answer: Option D

a tacheometer is fitted with an anal-latic lens (A) Additive constant is 100, multiplying constant is zero (B) Multiplying constant is 100, additive constant is zero (C) Both multiplying and additive constants are 100 (D) Both multiplying and additive constants are 50

Description : a tacheometer is fitted with an anal-latic lens (A) Additive constant is 100, multiplying constant is zero (B) Multiplying constant is 100, additive constant is zero (C) Both multiplying and additive constants are 100 (D) Both multiplying and additive constants are 50

Last Answer : (B) Multiplying constant is 100, additive constant is zero

Horizontal distances obtained tacheometerically are corrected for (A) Slope correction (B) Temperature correction (C) Refraction and curvature correction (D) All the above

Description : Horizontal distances obtained tacheometerically are corrected for  (A) Slope correction  (B) Temperature correction  (C) Refraction and curvature correction  (D) All the above 

Last Answer : (C) Refraction and curvature correction

Horizontal distances obtained by thermometric observations (A) Require slope correction (B) Require tension correction (C) Require slope and tension corrections (D) Do not require slope and tension corrections

Description : Horizontal distances obtained by thermometric observations (A) Require slope correction (B) Require tension correction (C) Require slope and tension corrections (D) Do not require slope and tension corrections

Last Answer : (D) Do not require slope and tension corrections

The horizontal angles from the boat between A and B and B and C, the stations on the shore are 1 2. The distances AB = L1 and BC = L2 2 at C between the boat and station B between A and C at B). (A) 1 2) = (L2 1/L1 2) = K (B) t 2 = 360° - 1 2 (C) 2 = sin /(K + ) (D) All the above

Description : The horizontal angles from the boat between A and B and B and C, the stations on the shore are 1 2. The distances AB = L1 and BC = L2 2 at C between the boat and station B between A and C at B). (A) 1 2) = (L2 1/L1 2) = K (B) t 2 = 360° - 1 2 (C) 2 = sin /(K + ) (D) All the above

Last Answer : (D) All the above

Which of the following in theodolite work is imperfect adjustment of the instrument (a) Error due to line of collimation being perpendicular to the horizontal axis (b) Error due to axis not to perpendicular of the vertical axis (c) Error due to imperfect graduation (d) Error due to eccentricity of vernires (e) All of the above*

Description : Which of the following in theodolite work is imperfect adjustment of the instrument (a) Error due to line of collimation being perpendicular to the horizontal axis (b) Error due to axis not to perpendicular ... to imperfect graduation (d) Error due to eccentricity of vernires (e) All of the above*

Last Answer : (e) All of the above*

Theodolite is an instrument used for (a) Tightening the capstan-headed nuts of level tube (b) Measurement of horizontal angles only (c) Measurement of vertical angles only (d) Measurement of both horizontal and vertical angles*

Description : Theodolite is an instrument used for (a) Tightening the capstan-headed nuts of level tube (b) Measurement of horizontal angles only (c) Measurement of vertical angles only (d) Measurement of both horizontal and vertical angles*

Last Answer : (d) Measurement of both horizontal and vertical angles*

Warner Bros. sells cookie jars, puzzles, photo albums, and other items featuring its popular cartoon characters directly through its retail outlets. This is an example of A)channel leadership. B)channel co -operation. C)channel conflict D)horizontal channel integration. E)vertical channel integration..

Description : Warner Bros. sells cookie jars, puzzles, photo albums, and other items featuring its popular cartoon characters directly through its retail outlets. This is an example of A)channel leadership. ... co -operation. C)channel conflict D)horizontal channel integration. E)vertical channel integration..

Last Answer : E)vertical channel integration..

The direction of projection for the range of a projectile to be maximum on an inclined plane having angle of inclination 30? to the horizontal, whould be a.45? with horizontal b.30? with vertical c.30? with horizontal d.60? with inclined plane e.45? with inclined plane

Description : The direction of projection for the range of a projectile to be maximum on an inclined plane having angle of inclination 30? to the horizontal, whould be a.45? with horizontal b.30? with vertical c.30? with horizontal d.60? with inclined plane e.45? with inclined plane

Last Answer : b. 30? with vertical

What is the name of the horizontal and the vertical lines drawn to determine the position of any point in the Cartesian plane? -Maths 9th

Description : What is the name of the horizontal and the vertical lines drawn to determine the position of any point in the Cartesian plane? -Maths 9th

Last Answer : The name of horizontal and vertical lines drawn to determine the position of any point in the Cartesian plane is x-axis and y-axis respectively

A light ray is incident on a plane mirror placed in a horizontal plane, making an angle of `30^(@)` with the vertical, then the angle between the refl

Description : A light ray is incident on a plane mirror placed in a horizontal plane, making an angle of `30^(@)` with the vertical, then the angle between the refl

Last Answer : A light ray is incident on a plane mirror placed in a horizontal plane, making an angle of `30^(@)` with the vertical, ... @)` C. `90^(@)` D. `30^(@)`

In order to get maximum radiation to all surrounding points in the horizontal plane, the antenna used is a A. vertical loop B. vertical quarter-wavelength rod C. array which includes parasitic elements D. a horizontal Hertz dipole

Description : In order to get maximum radiation to all surrounding points in the horizontal plane, the antenna used is a A. vertical loop B. vertical quarter-wavelength rod C. array which includes parasitic elements D. a horizontal Hertz dipole

Last Answer : B. vertical quarter-wavelength rod

A vertical loop antenna has a A. unidirectional radiation pattern in the horizontal plane B. unidirectional radiation pattern in the vertical plane C. omnidirectional radiation pattern in the horizontal plane D. a bidirectional radiation pattern in the horizontal plane

Description : A vertical loop antenna has a A. unidirectional radiation pattern in the horizontal plane B. unidirectional radiation pattern in the vertical plane C. omnidirectional radiation pattern in the horizontal plane D. a bidirectional radiation pattern in the horizontal plane

Last Answer : D. a bidirectional radiation pattern in the horizontal plane

Which of the following antennas receive signals in the horizontal plane equality well from all directions? A. Horizontal Hertz antenna B. Vertical loop antenna C. Vertical Yagi antenna D. A vertical antenna which is a quarter-wavelength long

Description : Which of the following antennas receive signals in the horizontal plane equality well from all directions? A. Horizontal Hertz antenna B. Vertical loop antenna C. Vertical Yagi antenna D. A vertical antenna which is a quarter-wavelength long

Last Answer : D. A vertical antenna which is a quarter-wavelength long

Which antenna radiates an omnidirectional pattern in the horizontal plane with vertical polarization? A. Marconi antenna B. Discone antenna C. Horn antenna D. Helical antenna

Description : Which antenna radiates an omnidirectional pattern in the horizontal plane with vertical polarization? A. Marconi antenna B. Discone antenna C. Horn antenna D. Helical antenna

Last Answer : A. Marconi antenna

Which of the following antennas receives signals equally well from all directions in a horizontal plane? A. Hetz antenna B. Vertical Marconi antenna C. Yagi antenna D. Helical antenna

Description : Which of the following antennas receives signals equally well from all directions in a horizontal plane? A. Hetz antenna B. Vertical Marconi antenna C. Yagi antenna D. Helical antenna

Last Answer : B. Vertical Marconi antenna

The electric field lies in a plane parallel to the earth’s surface. A. Elliptical polarization B. Horizontal polarization C. Vertical polarization D. Circular polarization

Description : The electric field lies in a plane parallel to the earth’s surface. A. Elliptical polarization B. Horizontal polarization C. Vertical polarization D. Circular polarization

Last Answer : B. Horizontal polarization

The electric field lines in a plane perpendicular to the earth’s surface. A. Elliptical polarization B. Circular polarization C. Horizontal polarization D. Vertical polarization

Description : The electric field lines in a plane perpendicular to the earth’s surface. A. Elliptical polarization B. Circular polarization C. Horizontal polarization D. Vertical polarization

Last Answer : D. Vertical polarization

Flail mower is a mower with high speed swinging knives, operating in a. horizontal plane c. Vertical plane d. None of above

Description : Flail mower is a mower with high speed swinging knives, operating in a. horizontal plane c. Vertical plane d. None of above

Last Answer : Ans-   b. either in the horizontal plane or in the vertical plane