Chemical engineering plant cost index is used for finding the present cost of a particular chemical plant, if the cost of similar plant at some time in the past is known. The present cost of the plant = original cost × (index value at present/ index value at time original cost was obtained). The most major component of this cost index is (A) Fabricated equipment and machinery (B) Process instruments and control (C) Pumps and compressor (D) Electrical equipments and material

Chemical engineering plant cost index is used for finding the present cost of a particular chemical plant, if the cost of similar plant at some time in the past is known.
The present cost of the plant = original cost × (index value at present/ index value at time original cost was obtained). The most major component of this cost index is
(A) Fabricated equipment and machinery
(B) Process instruments and control
(C) Pumps and compressor
(D) Electrical equipments and material
by

1 Answer

Answer :

(A) Fabricated equipment and machinery
by

Related questions

Pick out the wrong statement. (A) The annual depreciation rate for machinery and equipments in a chemical process plant is about 10% of the fixed capital investment (B) Annual depreciation rate of buildings in a chemical plant is about 3% of its initial cost (C) Insurance rates on annual basis in a chemical plant may be about 1% of the fixed capital investment (D) In a chemical industry, research and development cost amounts to about 15% of net sales realisation (NSR)

Description : Pick out the wrong statement. (A) The annual depreciation rate for machinery and equipments in a chemical process plant is about 10% of the fixed capital investment (B) Annual depreciation rate ... chemical industry, research and development cost amounts to about 15% of net sales realisation (NSR)

Last Answer : (D) In a chemical industry, research and development cost amounts to about 15% of net sales realisation (NSR)

'Lang factor' is defined as the ratio of the capital investment to the delivered cost of major equipments. The value of 'Lang factor' for fixed capital investment, for a solid-fluid processing chemical plant ranges from (A) 1.2 to 1.4 (B) 2.5 to 2.7 (C) 4.2 to 4.4 (D) 6.2 to 6.4

Description : 'Lang factor' is defined as the ratio of the capital investment to the delivered cost of major equipments. The value of 'Lang factor' for fixed capital investment, for a solid-fluid processing chemical plant ranges from (A) 1.2 to 1.4 (B) 2.5 to 2.7 (C) 4.2 to 4.4 (D) 6.2 to 6.4

Last Answer : C) 4.2 to 4.4

Hastelloy C is a good material of construction in chemical process industry, since it is (A) Highly corrosion resistant and is readily fabricated (B) Relatively inexpensive although it can be fabricated with some difficulty (C) Corrosion resistant to most alkalis, particularly because of its copper content (D) Light and resists attack by acids

Description : Hastelloy C is a good material of construction in chemical process industry, since it is (A) Highly corrosion resistant and is readily fabricated (B) Relatively inexpensive although it can be ... most alkalis, particularly because of its copper content (D) Light and resists attack by acids

Last Answer : (D) Light and resists attack by acids

Which of the following is not a component of depreciation cost? (A) Repairs and maintenance cost (B) Loss due to obsolescence of the equipment (C) Loss due to decrease in the demand of product (D) Loss due to accident/breakdown in the machinery

Description : Which of the following is not a component of depreciation cost? (A) Repairs and maintenance cost (B) Loss due to obsolescence of the equipment (C) Loss due to decrease in the demand of product (D) Loss due to accident/breakdown in the machinery

Last Answer : (A) Repairs and maintenance cost

Alinco, which is a aluminium-cobalt-nickel steel, is used for making (A) Surgical instruments (B) Powerful magnets (C) Chemical equipments (D) Boiler tubes

Description : Alinco, which is a aluminium-cobalt-nickel steel, is used for making (A) Surgical instruments (B) Powerful magnets (C) Chemical equipments (D) Boiler tubes

Last Answer : (B) Powerful magnets

Purchased cost of equipments for a chemical process plant ranges from __________ percent of the fixed capital investment. (A) 10 to 20 (B) 20 to 40 (C) 45 to 60 (D) 65 to 75

Description : Purchased cost of equipments for a chemical process plant ranges from __________ percent of the fixed capital investment. (A) 10 to 20 (B) 20 to 40 (C) 45 to 60 (D) 65 to 75

Last Answer : (B) 20 to 40

A publishing company purchases a computer to aid in stock control. This computer is an example of which type of industrial product? A)Raw material B)Major supplies C)Accessory equipment D)Component part

Description : A publishing company purchases a computer to aid in stock control. This computer is an example of which type of industrial product? A)Raw material B)Major supplies C)Accessory equipment D)Component part

Last Answer : C)Accessory equipment

Which of the following is not a component of the fixed capital for a chemical plant facility? (A) Raw materials inventory (B) Utilities plants (C) Process equipment (D) Emergency facilities

Description : Which of the following is not a component of the fixed capital for a chemical plant facility? (A) Raw materials inventory (B) Utilities plants (C) Process equipment (D) Emergency facilities

Last Answer : (A) Raw materials inventory

Which of the spaces listed is defined as a 'location requiring an exceptional degree of protection' when considering the installation of shipboard electrical equipment? A. Machinery space B. Chart room C. Console room D. Accommodation space

Description : Which of the spaces listed is defined as a 'location requiring an exceptional degree of protection' when considering the installation of shipboard electrical equipment? A. Machinery space B. Chart room C. Console room D. Accommodation space

Last Answer : Answer: A

Hard ferrites are used for making (A) Transformer cores. (B) Electrical machinery. (C) High frequency equipment. (D) Light weight permanent magnets.

Description : Hard ferrites are used for making (A) Transformer cores. (B) Electrical machinery. (C) High frequency equipment. (D) Light weight permanent magnets.

Last Answer : (D) Light weight permanent magnets.

In a group housing project, it is proposed to use pre-fabricated RCC beams and columns. The most useful construction equipment is (a) Derrick Crane (b) Chute (c) Weigh Batcher (d) Transit Mixer

Description : In a group housing project, it is proposed to use pre-fabricated RCC beams and columns. The most useful construction equipment is (a) Derrick Crane (b) Chute (c) Weigh Batcher (d) Transit Mixer

Last Answer : (a) Derrick Crane

In an ordinary chemical plant, electrical installation cost may be about (A) 10-15% of purchased equipment cost (B) 3-10% of fixed capital investment (C) Either (A) or (B) (D) Neither (A) nor (B)

Description : In an ordinary chemical plant, electrical installation cost may be about (A) 10-15% of purchased equipment cost (B) 3-10% of fixed capital investment (C) Either (A) or (B) (D) Neither (A) nor (B)

Last Answer : (C) Either (A) or (B)

Fixed capital investment of a chemical plant is the total amount of money needed to supply the necessary plant and manufacturing facilities plus the working capital for operation of the facilities. Which of the following components of fixed capital investment requires minimum percentage of it? (A) Electrical installation cost (B) Equipment installation cost (C) Cost for piping (D) Equipment insulation cost

Description : Fixed capital investment of a chemical plant is the total amount of money needed to supply the necessary plant and manufacturing facilities plus the working capital for operation of the facilities. Which of ... (B) Equipment installation cost (C) Cost for piping (D) Equipment insulation cost

Last Answer : (D) Equipment insulation cost

What are the auxiliary equipments of compressor?

Description : What are the auxiliary equipments of compressor?

Last Answer : Answer: Lube oil consoles, Seal oil consoles, Surface condensers, Condensate pump, Air blowers, Inlet air filters, waste heat system, compressor suction drum, knock out pot, Pulsation dampner, volume bottles, Inter and after coolers.

What are the raw material machinery tools and equipment required for the production Coffee shop?

Description : What are the raw material machinery tools and equipment required for the production Coffee shop?

Last Answer : Need answer

For centrifugal pumps (A) Initial cost is low (B) Limited space is required (C) The discharge obtained is steady and non-pulsating (D) All the above

Description : For centrifugal pumps  (A) Initial cost is low  (B) Limited space is required  (C) The discharge obtained is steady and non-pulsating  (D) All the above 

Last Answer : (D) All the above 

What are the destinations of the organic material fabricated by the producers ?

Description : What are the destinations of the organic material fabricated by the producers ?

Last Answer : Part of the organic material synthesized by the producers is consumed as energy source for the metabolism of the own producer individual. Other part is incorporated (into the body) and become available ... and only a fraction is incorporated and become available as food for the following level.

Large tools and machines used in a production process for a considerable length of time are classified as A)major equipment. B)accessory equipment. C)component parts. D)raw materials. E)consumable supplies.

Description : Large tools and machines used in a production process for a considerable length of time are classified as A)major equipment. B)accessory equipment. C)component parts. D)raw materials. E)consumable supplies.

Last Answer : A)major equipment

Cost incurred towards __________ in a chemical plant is a component of the utilities cost. (A) Water supply (B) Running a control laboratory (C) Property protection (D) Medical services

Description : Cost incurred towards __________ in a chemical plant is a component of the utilities cost. (A) Water supply (B) Running a control laboratory (C) Property protection (D) Medical services

Last Answer : (A) Water supply

Plate towers are preferred to packed towers, when large temperature changes are involved, because of the reason that the (A) Packing may be crushed due to thermal expansion/contraction of the components of the equipments (B) Pressure drop in the equipment will be very high (C) Viscosity variation of the fluids may cause channelling/flooding (D) None of these

Description : Plate towers are preferred to packed towers, when large temperature changes are involved, because of the reason that the (A) Packing may be crushed due to thermal expansion/contraction of the ... C) Viscosity variation of the fluids may cause channelling/flooding (D) None of these

Last Answer : (A) Packing may be crushed due to thermal expansion/contraction of the components of the equipments

Out of the following processes of paper pulp manufacture, the maximum corrosion problem in digestion & handling equipments is encountered in the __________ process. (A) Mechanical (B) Sulphate/Kraft (C) Sulphite (D) Neutral sulphite semi-chemical

Description : Out of the following processes of paper pulp manufacture, the maximum corrosion problem in digestion & handling equipments is encountered in the __________ process. (A) Mechanical (B) Sulphate/Kraft (C) Sulphite (D) Neutral sulphite semi-chemical

Last Answer : (D) Neutral sulphite semi-chemical

Items that are purchased routinely, do not become part of the final physical product, and are treated like expense items rather than capital goods are called 1. raw materials 2. major equipment 3. accessory equipment 4. component part 5. process materials

Description : Items that are purchased routinely, do not become part of the final physical product, and are treated like expense items rather than capital goods are called 1. raw materials 2. major equipment 3. accessory equipment 4. component part 5. process materials

Last Answer : accessory equipment

Items that are purchased routinely, do not become part of the final physical product, and are treated like expense items rather than capital goods are called A)raw materials. B)major equipment. C)accessory equipment. D)component parts. E)process materials.

Description : Items that are purchased routinely, do not become part of the final physical product, and are treated like expense items rather than capital goods are called A)raw materials. B)major equipment. C)accessory equipment. D)component parts. E)process materials.

Last Answer : C)accessory equipment.

All of the following are property, plant, and equipment except a. supplies. b. machinery. c. land. d. buildings.

Description : All of the following are property, plant, and equipment except a. supplies. b. machinery. c. land. d. buildings.

Last Answer : a. supplies.

Moisture absorbed in the windings or condensed on the surface of electrical machinery insulation ________. A. is good for long term preserving since most insulation is organic and contains some amount B. lowers the insulation value and is a common cause of fault grounds in idle machines C. will enhance insulation resistance only if it is fresh water and contains no salt D. reduces the amount of current supplied or drawn by the machine so horsepower is limited

Description : Moisture absorbed in the windings or condensed on the surface of electrical machinery insulation ________. A. is good for long term preserving since most insulation is organic and contains some amount B. ... D. reduces the amount of current supplied or drawn by the machine so horsepower is limited

Last Answer : Answer: B

An insulation resistance test is performed on a particular piece of electric equipment. In addition to the resistance reading, what information listed below should be entered in the electrical log? A. The maximum allowable operating temperature of the machine. B. The temperature of the machine at the time the resistance reading was taken. C. The normal temperature rise of the machine. D. The complete nameplate data from the resistance test instrument used to obtain the reading.

Description : An insulation resistance test is performed on a particular piece of electric equipment. In addition to the resistance reading, what information listed below should be entered in the electrical log? A. ... D. The complete nameplate data from the resistance test instrument used to obtain the reading.

Last Answer : Answer: B

Which of the following is not a source of ozone emission in the atmosphere? (A) Refrigerators (B) Xerox machines (C) Dermatological photo-therapy equipments (D) High voltage electrical equipments

Description : Which of the following is not a source of ozone emission in the atmosphere? (A) Refrigerators (B) Xerox machines (C) Dermatological photo-therapy equipments (D) High voltage electrical equipments

Last Answer : (A) Refrigerators

Silicon percentage in the silicon steel used for electrical appliances/equipments is (A) 0.3-0.4 (B) 12-14 (C) 3-4 (D) 20-25

Description : Silicon percentage in the silicon steel used for electrical appliances/equipments is (A) 0.3-0.4 (B) 12-14 (C) 3-4 (D) 20-25

Last Answer : Option C

Silicon percentage in silicon steel used for electrical equipments is about (A) 1 (B) 4.0 (C) 8 (D) 14

Description : Silicon percentage in silicon steel used for electrical equipments is about (A) 1 (B) 4.0 (C) 8 (D) 14

Last Answer : Option B

Equipment installation cost in a chemical process plant ranges from __________ percent of the purchased equipment cost. (A) 10 to 20 (B) 35 to 45 (C) 55 to 65 (D) 70 to 80

Description : Equipment installation cost in a chemical process plant ranges from __________ percent of the purchased equipment cost. (A) 10 to 20 (B) 35 to 45 (C) 55 to 65 (D) 70 to 80

Last Answer : (B) 35 to 45

Work input to the air compressor with n as index of compression A. Increases with increase in value of n B. Decrease with increase in value of n C. remains same whatever the value of n D. first increase and then decreases with increase of value of n.

Description : Work input to the air compressor with n as index of compression A. Increases with increase in value of n B. Decrease with increase in value of n C. remains same whatever the value of n D. first increase and then decreases with increase of value of n.

Last Answer : ANSWER : A

Minimum work in compressor is possible when the value of adiabatic index n is equal to  (a) 0.75  (b) 1  (c) 1.27  (d) 1.35  (e) 2.

Description : Minimum work in compressor is possible when the value of adiabatic index n is equal to  (a) 0.75  (b) 1  (c) 1.27  (d) 1.35  (e) 2.

Last Answer : Answer : b

The necessary condition for phase equilibrium in a multiphase system of N components is that the (A) Chemical potentials of a given component should be equal in all phases (B) Chemical potentials of all components should be same in a particular phase (C) Sum of the chemical potentials of any given component in all the phases should be the same (D) None of these

Description : The necessary condition for phase equilibrium in a multiphase system of N components is that the (A) Chemical potentials of a given component should be equal in all phases (B) Chemical potentials of all ... potentials of any given component in all the phases should be the same (D) None of these

Last Answer : (A) Chemical potentials of a given component should be equal in all phases

Agriculture machinery can be divided into following groups they are.... a) farm machinery c) drain engineering b) irrigation engineering d) all of the above

Description : Agriculture machinery can be divided into following groups they are.... a) farm machinery c) drain engineering b) irrigation engineering d) all of the above

Last Answer :  all of the above

Light oil whose major component is Benzol, is obtained by the distillation of crude tar in the temperature range of __________ °C. (A) 80-170 (B) 200-300 (C) 250-270

Description : Light oil whose major component is Benzol, is obtained by the distillation of crude tar in the temperature range of __________ °C. (A) 80-170 (B) 200-300 (C) 250-270

Last Answer : (A) 80-170

Work done in an adiabatic process between a given pair of end states depends on  (a) the end states only  (b) particular adiabatic process  (c) the value of index n  (d) the value of heattransferred  (e) mass of the system.

Description : Work done in an adiabatic process between a given pair of end states depends on  (a) the end states only  (b) particular adiabatic process  (c) the value of index n  (d) the value of heattransferred  (e) mass of the system.

Last Answer : Answer : a

'Utilities' in a chemical process plant includes compressed air, steam, water, electrical power, oxygen, acetylene, fuel gases etc. Utility costs for ordinary chemical process plants ranges roughly from __________ percent of the total product cost. (A) 1 to 5 (B) 10 to 20 (C) 25 to 35 (D) 35 to 45

Description : 'Utilities' in a chemical process plant includes compressed air, steam, water, electrical power, oxygen, acetylene, fuel gases etc. Utility costs for ordinary chemical process plants ranges roughly from __________ percent of the total product ... 1 to 5 (B) 10 to 20 (C) 25 to 35 (D) 35 to 45

Last Answer : (B) 10 to 20

ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Description : ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Last Answer : B. Communications satellite

Principle of similitude forms the basis of (A) Comparing two identical equipments (B) Designing models so that the result can be converted to prototypes (C) Comparing similarity between design and actual equipment (D) Hydraulic designs

Description : Principle of similitude forms the basis of (A) Comparing two identical equipments (B) Designing models so that the result can be converted to prototypes (C) Comparing similarity between design and actual equipment (D) Hydraulic designs

Last Answer : Answer: Option B

Draw neat labeled diagram of single phase AC locomotive showing its various equipments of power circuit and give function of each equipment used in power circuit.

Description : Draw neat labeled diagram of single phase AC locomotive showing its various equipments of power circuit and give function of each equipment used in power circuit.

Last Answer : Functions of equipment: 1) circuit breaker: disconnects the locomotive equipment from the supply in the event of fault in the equipment / loco. 2) On load tap changer, used to control the ... 6) Traction motor: operates as per the required operating characteristics to take on the traction load.

As the production manager of an engineering firm, you went out and bought a metal cutting machine. What you have purchased can best be classified as A)raw material. B)a processed component. C)a component part. D)a service. E)an industrial product.

Description : As the production manager of an engineering firm, you went out and bought a metal cutting machine. What you have purchased can best be classified as A)raw material. B)a processed component. C)a component part. D)a service. E)an industrial product.

Last Answer : E)an industrial product.

The original cost of an equipment is Rs.10,000. Its salvage value at the end of its total useful life of five years is Rs. 1,000. Its book value at the end of two years of its useful life (as per straight line method of evaluation of depreciation) will be (A) Rs. 8,800 (B) Rs. 7,600 (C) Rs. 6,400 (D) Rs. 5,000

Description : The original cost of an equipment is Rs.10,000. Its salvage value at the end of its total useful life of five years is Rs. 1,000. Its book value at the end of two years of its useful life (as per straight line method of evaluation ... be (A) Rs. 8,800 (B) Rs. 7,600 (C) Rs. 6,400 (D) Rs. 5,000

Last Answer : (C) Rs. 6,400

What would be appropriate to give to my nephew, who has obtained a Doctorate in chemical and biological engineering?

Description : What would be appropriate to give to my nephew, who has obtained a Doctorate in chemical and biological engineering?

Last Answer : answer:A card and this shirt http://www.thinkgeek.com/tshirts/sciencemath/2891/ might It’s a shirt on Think Geek showing the caffeine molecule (very nerdy and appropriate for a biological engineer who just might be a “user”.

Pick out the wrong statement. (A) Alloys are harder than their component elements (B) Presence of silicon in steel decreases its electrical resistance (C) Karbate is an acid resistant material of construction (D) Nichrome, a steel alloyed with 10% Ni and 20% Cr can be used upto a temperature of 1100°C

Description : Pick out the wrong statement. (A) Alloys are harder than their component elements (B) Presence of silicon in steel decreases its electrical resistance (C) Karbate is an acid resistant material of construction ... , a steel alloyed with 10% Ni and 20% Cr can be used upto a temperature of 1100°C

Last Answer : (B) Presence of silicon in steel decreases its electrical resistance

A pump can fill a cistern in 12 hrs. After half the cistern is filled, 3 more similar pumps are opened. What is the total time taken to fill the cistern completely? A) 8 hrs B) 4 hrs C) 2hrs D) 7.5 hrs

Description : A pump can fill a cistern in 12 hrs. After half the cistern is filled, 3 more similar pumps are opened. What is the total time taken to fill the cistern completely? A) 8 hrs B) 4 hrs C) 2hrs D) 7.5 hrs

Last Answer : D Time taken by 1 pump to fill tha half tank = 6 hrs Part filled by the 4 pumps in 1 hr = 4 * 1/12 =1/12 =>1/3 Remaining part = (1 – 1/2)= 1/2 Therefore 1/3 :1/2 :: 1:x X=1.5 hrs So total time takem = 6hrs + 1.5 hrs = 7.5 hrs.

The insulation resistance of electric equipment and machinery should be tested for the lowest normal insulation values _____________. A. immediately after shutting down the machine B. every time the brush rigging is adjusted C. immediately after starting up the machine D. every 30 days whether the machine is in use or not

Description : The insulation resistance of electric equipment and machinery should be tested for the lowest normal insulation values _____________. A. immediately after shutting down the machine B. every time the brush rigging is ... starting up the machine D. every 30 days whether the machine is in use or not

Last Answer : Answer: A

What are the safety precautions when working on electrical equipments?

Description : What are the safety precautions when working on electrical equipments?

Last Answer : Switch off power, wear proper protective clothing, safety shoes, Notice board : Do not switch on - Men at work, stand on rubber mat, remove metal rings, watch bracelets, use proper insulated tools, ... work permit. In case of electrical shock, give proper first aid, check heart beat and pulse.

List any four internal causes for abnormal operation of electrical equipment’s.

Description : List any four internal causes for abnormal operation of electrical equipment’s. 

Last Answer : Internal causes:- 1. Open circuit 2. Short circuit 3. Earth fault 4. Loose connection 5. Deposit of dirt and dust near ventilation passage 6. Low insulation resistance 7. Improper maintenance 8. Poor ... problems 13. Failure of cooling system 14. Excess wear and tear of internal parts 15. Ageing.

Which of the following branch is not a parts of robotics? A : Computer Engineering B : Mechanical Engineering C : Electrical Engineering D : Chemical Engineering

Description : Which of the following branch is not a parts of robotics? A : Computer Engineering B : Mechanical Engineering C : Electrical Engineering D : Chemical Engineering

Last Answer : D : Chemical Engineering

Which of the following branch is not a parts of robotics? A : Computer Engineering B : Mechanical Engineering C : Electrical Engineering D : Chemical Engineering

Description : Which of the following branch is not a parts of robotics? A : Computer Engineering B : Mechanical Engineering C : Electrical Engineering D : Chemical Engineering

Last Answer : D : Chemical Engineering