Define supply voltage Rejection Ratio and Output voltage Swing.

by

1 Answer

Answer :

Supply Voltage Rejection Ratio: It is defined as the ratio of change of input offset voltage to the change in one supply voltage while keeping other supply voltage constant. Ideally, SVRR=0

Output Voltage Swing: It is defined as the maximum unclipped peak to peak output voltage that an OPAMP can produce. Since the quiescent output is ideally zero, the ac output voltage

by

Related questions

What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?

Description : What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?

Last Answer : -5 volts.

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Description : An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Last Answer : Solution:

Assertion A: For a given depth of cut, the output of a power shovel can be increased by decreasing the angle of swing. Reason R: If the angle of swing is decreased, the cycle time will be decreased. Select the correct answer. (A) Both A and R is true and R is the correct explanation of A (B) Both A and R is true but R is not the correct explanation of A (C) A is true but R is false (D) A is false but R is true

Description : Assertion A: For a given depth of cut, the output of a power shovel can be increased by decreasing the angle of swing. Reason R: If the angle of swing is decreased, the cycle time will be decreased. Select the ... explanation of A (C) A is true but R is false (D) A is false but R is true

Last Answer : (A) Both A and R is true and R is the correct explanation of A

If the output of a dragline for 90° angle of swing at optimum depth of cut is X, then the output for 120° angle of swing at 120 % of optimum depth of cut will be (A) Equal to X (B) More than X (C) Less than X (D) Any of the above

Description : If the output of a dragline for 90° angle of swing at optimum depth of cut is X, then the output for 120° angle of swing at 120 % of optimum depth of cut will be (A) Equal to X (B) More than X (C) Less than X (D) Any of the above

Last Answer : (C) Less than X

Otto cycle efficiency is higher than Diesel cycle efficiency for the same compression ratio and heat input because in Otto cycle  A. combustion is at constant volume  B. expansion and compression are isentropic  C. maximum temperature is higher  D. heat rejection is lower

Description : Otto cycle efficiency is higher than Diesel cycle efficiency for the same compression ratio and heat input because in Otto cycle  A. combustion is at constant volume  B. expansion and compression are isentropic  C. maximum temperature is higher  D. heat rejection is lower

Last Answer : Answer: D

In op-amp operation, Common Mode Rejection Ratio (CMRR)

Description : In op-amp operation, Common Mode Rejection Ratio (CMRR)

Last Answer : In op-amp operation, Common Mode Rejection Ratio (CMRR) is desired to be high

What is the deviation ratio for an FM-phone signal having a maximum frequency swing of plus or minus 5 kHz and accepting a maximum modulation rate of 3kHz? A. 60 B. 0.16 C. 0.6 D. 1.66

Description : What is the deviation ratio for an FM-phone signal having a maximum frequency swing of plus or minus 5 kHz and accepting a maximum modulation rate of 3kHz? A. 60 B. 0.16 C. 0.6 D. 1.66

Last Answer : D. 1.66

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

A resistor placed in parallel to the output of a power supply _____________. A. is a temperature compensator B. corrects power factor C. prevents excessive currents D. aids in output voltage regulation

Description : A resistor placed in parallel to the output of a power supply _____________. A. is a temperature compensator B. corrects power factor C. prevents excessive currents D. aids in output voltage regulation

Last Answer : Answer: D

Capacitors are used on the output of the power supply in today's consoles to _____________. A. filter out 'ripple' B. prevent overloads C. act as a permanent load D. decrease the average value of the output voltage

Description : Capacitors are used on the output of the power supply in today's consoles to _____________. A. filter out 'ripple' B. prevent overloads C. act as a permanent load D. decrease the average value of the output voltage

Last Answer : Answer: A

The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be (A) 3.6 V. (B) 2.5 V. (C) 3.0 V. (D) 6.0 V.

Description : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be (A) 3.6 V. (B) 2.5 V. (C) 3.0 V. (D) 6.0 V.

Last Answer : (C) 3.0 V.

Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life.

Description : Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life. 

Last Answer : 1) Effect on Current:- In LED current depends upon supply voltage, if voltage get changes then current also change but this change in current will be control by resistors which are connected in series.  2) ...   4) Effect on Life:- If supply voltage is not stable then life of LED get reduced. 

A single phase transformer is designed to operate from 50 Hz, 1100 V supply and to have an output voltage

Description : A single phase transformer is designed to operate from 50 Hz, 1100 V supply and to have an output voltage of 240 V at no load. The core has mean area of 30 cm2 and the flux density has not to exceed 1.3T. The number of secondary turns will be (a) 1270 (b) 1017 (c) 768 (d) 277  

Last Answer : E2=e2=4.44*flux*N2*f=240 V Flux=Flux density* Area Area=30 cm2  =30*10-4 m2 Flux= 1.3*30*10-4  Wb=39*10-4 Wb E=240= 4.44*39*10-4 *N2*50      N2=277.

Define swing curve?

Description : Define swing curve?

Last Answer : The swing curve is the plot between the power angle and time. It is usually plotted for a transient state to stydy the nature of variation in angle for a sudden large disturbance.

Define swing of telescope

Description : Define swing of telescope

Last Answer : It the process of turning the telescope in horizontal plane about vertical axis.

Effective demand depends on - (1) capital-output ratio (2) output-capital ratio (3) total expenditure (4) supply price

Description : Effective demand depends on - (1) capital-output ratio (2) output-capital ratio (3) total expenditure (4) supply price

Last Answer : (4) supply price Explanation: Effective Demand is "the demand in which the consumer are able and willing to purchase at conceivable price" simply saying if the product price is low more ... Function or Price and Aggregate Supply Function or Price to explain the determination of effective demand.

Effective demand depends on (1) capital-output ratio (2) output-capital ratio (3) total expenditure (4) supply price

Description : Effective demand depends on (1) capital-output ratio (2) output-capital ratio (3) total expenditure (4) supply price

Last Answer : supply price

The swing equation for a synchronous machine is based on

Description : The swing equation for a synchronous machine is based on (A) relative motion between load angle and stator magnetic field (B) maximum power flow possible through a particular point (C) net torque and angular displacement (D) relation between excitation voltage and excitation current

Last Answer : The swing equation for a synchronous machine is based on (A) relative motion between load angle and stator magnetic field (B) maximum power flow possible through a particular point (C) net torque and angular displacement (D) relation between excitation voltage and excitation current

Figure 'D' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'D' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: A

Figure 'C' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'C' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: C

Figure 'B' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'B' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: B

Figure 'A' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'A' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: B

A power supply produces a 0.6 W output with an input of 0.7 W. Its percentage of efficiency is:

Description : A power supply produces a 0.6 W output with an input of 0.7 W. Its percentage of efficiency is: A. 8.57% B. 42.85% C. 4.28% D. 85.7%

Last Answer : A power supply produces a 0.6 W output with an input of 0.7 W. Its percentage of efficiency is: 85.7%

In _____________ sensor, output voltage changes in proportion to air-fuel ratio. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Description : In _____________ sensor, output voltage changes in proportion to air-fuel ratio. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Last Answer : Answer: b Explanation: Only in exhaust gas sensor, output voltage changes in proportion to air-fuel ratio.

In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC

Description : In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC

Last Answer : Answer: D

Define: i) Input Offset Voltage ii) Input offset Current iii) Input Bias Current iv) Output offset voltage

Description : Define: i) Input Offset Voltage ii) Input offset Current iii) Input Bias Current iv) Output offset voltage

Last Answer : Definition of parameters of OPAMP is follows:  i) Input Offset Voltage: Input offset voltage is defined as the voltage that must be applied between the two input terminals of an OPAMP to null or ... to ground) and output voltage is obtained non zero such voltage is output offset voltage of opamp.

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

voltage regulator on power supply

Description : …Hi,  When we supply the microcontroller we use  12V step down transformer> rectifier> filter> 5V voltage regulator. Why not use? 5V transformer> rectifier>filter only. And what voltage regulator will do in our microcontroller?

Last Answer : The powering supply voltage to a microcontroller is 5v if you use a 5v transformer if there is loss of power your output voltage will be drop in the rectifier and there will be change in voltage these can be overcome using a regulator it will give a constant output

State the following, 1) Position of head light 2) Supply voltage for flasher light 3) Colours used for marker light 4) Frequencies for engine horn.

Description : State the following, 1) Position of head light 2) Supply voltage for flasher light 3) Colours used for marker light 4) Frequencies for engine horn. 

Last Answer : Ans: 1) Position of head light: Head light is located at center near roof level. 2) Supply voltage for flasher light: Nominal 110 V. dc, range 70 V to 140 V. 3) Colours used for marker light: ... indicates parking light 4) Frequencies for engine horn: For HT horn - 660 Hz For LT horn - 330 Hz

In an energymeter which coil carries the current proportional to supply voltage _____.

Description :  In an energymeter which coil carries the current proportional to supply voltage _____. 

Last Answer :  In an energymeter which coil carries the current proportional to supply voltage Pressure coil. 

A commercial power supply has a voltage regulation of:

Description : A commercial power supply has a voltage regulation of:  1. 1% 2.5% 3.20% 4.50% 

Last Answer : A commercial power supply has a voltage regulation of: 1%

What happens to the voltage in the secondary when the frequency of the supply in the primary is decreased?

Description : What happens to the voltage in the secondary when the frequency of the supply in the primary is decreased? A) It increases B) It decreases C) It remains the same D) Cannot say unless the actual percentage increase in the frequency is known

Last Answer : What happens to the voltage in the secondary when the frequency of the supply in the primary is decreased? A) It increases B) It decreases C) It remains the same D) Cannot say unless the actual percentage increase in the frequency is known

Reduction in supply voltage by 10% will change the torque of an induction motor by

Description : Reduction in supply voltage by 10% will change the torque of an induction motor by   (a) 38% (b) 19% (c) 9.5% (d) No change 

Last Answer : Answer is (b)

What's the best way you've seen someone take rejection?

Description : What's the best way you've seen someone take rejection?

Last Answer : Get rejected, LIKE A BOSS shit on Deborahs desk, LIKE A BOSS

Have you heard that the Texas rejection of Obamacare will cost the state one hundred billion dollars in federal Medicaid money?

Description : Have you heard that the Texas rejection of Obamacare will cost the state one hundred billion dollars in federal Medicaid money?

Last Answer : answer:Texans have shown that ideology (radical right wing) is more important to them than serving citizens or saving money. The way I see it, they're so full of themselves they could care less ... when Houston has floods and the governor asks from FEMA help. Then they like the federal government.)

Would you apply again for a job you were rejected for if the rejection happened a year ago ?

Description : Would you apply again for a job you were rejected for if the rejection happened a year ago ?

Last Answer : What have you got to lose?

How do you deal with rejection?

Description : How do you deal with rejection?

Last Answer : Probably a little too personal initially. But I always think things through and try to step into their shoes.

What word defines rejecting a rejection?

Description : What word defines rejecting a rejection?

Last Answer : I’m not aware of such a word. Can you write a sentence in which you would use it? Just put a blank or a placeholder in brackets in the position where you think the word belongs.

How has rejection(in any form) affected you and have you learned anything out of it?

Description : How has rejection(in any form) affected you and have you learned anything out of it?

Last Answer : answer:Yes, rejection has made me stronger and has taught me about myself. I feel that I have become tougher because of it. Not all of it matters to me as much as it used to, although there are still some ... and it's not always a bad thing. It can even be a gift, whether we recognize that or not.

How do you deal with rejectIon of your son after leaving his dad and dad won't allow him to see me?

Description : How do you deal with rejectIon of your son after leaving his dad and dad won't allow him to see me?

Last Answer : How is his father legally able to keep you from seeing your son?

Advice on this rejection letter?

Description : Advice on this rejection letter?

Last Answer : Honestly I think it’s kind of patronizing. Rejection sucks, and the thing that sucks about it is being rejected, not the delivery. It’s important to learn how to deal with it and each person is going to have to do that in his/her own way.

As far as peoples' opinions of you, what is more frightening/threatening to you: rejection or indifference?

Description : As far as peoples' opinions of you, what is more frightening/threatening to you: rejection or indifference?

Last Answer : In my 20’s, my friends would be hypercritical of me, and those who didn’t like me said wonderful things about me. I don’t care what anyone thinks about me, and I don’t mind indifference. As Popeye so elegantly put it, I yam what I yam.

What are some ways to cope with rejection from a coworker?

Description : What are some ways to cope with rejection from a coworker?

Last Answer : Hey, don’t quit! There is much to be admired about a person who has the guts to tell someone their true feelings! At the very least,it shows that you are a caring person. For what it is worth,you have my respect.Hold your head up!

Is the myth about 'touching baby rabbit will cause rejection from mother rabbit' is really right?

Description : Is the myth about 'touching baby rabbit will cause rejection from mother rabbit' is really right?

Last Answer : answer:It's a myth. Wildlife rehabilitators (who are often forced to return perfectly healthy animals to perfectly fine situation because humans have decided to interfere) will tell you that handling babies ... may have been given a death sentance by people thinking that they're trying to help.)

How do you handle rejection?

Description : How do you handle rejection?

Last Answer : I would have to care in some personal way about the one doing the rejecting, and then decide if it was worthwhile to attempt to repair the rupture, or better to let it go.

Have you ever stuck to it in the face of repeated rejection?

Description : Have you ever stuck to it in the face of repeated rejection?

Last Answer : Yes! soo many times I had gigs playing my guitar EVERYWHERE and nobody was interested. I could never get anybody to like my music until I started singing it was weird. check it: www.myspace.com/praisesrising now people buy my cd’s all the time :)

Why do some people not take rejection as well as others?

Description : Why do some people not take rejection as well as others?

Last Answer : Well why does a bear shit in the woods?? It just does. Thats human nature