Write eight desirable characteristics of traction motor.

1 Answer

Answer :

Desirable characteristics of ideal traction motors:- 1) It should be robust in construction to withstand against continuous vibrations. 2) Weight of motor per HP should be minimum in order to increase pay load capacity. 3) It must be small in overall dimensions, especially in overall diameter. 4) It must have totally enclosed type enclosure to provide protection against entry of dirt, dust, mud, water etc. in drive. 5) When motors are running in parallel they should share almost equal load. (even when there is unequal wear & tear of driving wheels) 6) It should have high starting torque. 7) It should possess high rate of acceleration & retardation. 8) It should be variable speed motor. 9) Its speed-torque characteristics should be such that it should produce high torque at low speed and low toque at high speed. 10) Motor must be capable of taking excessive overload in case of emergency. 11)It should have simple speed control methods. 12) Electrical braking system should be reliable, easy to operate and control, especially regenerative braking is possible. 13) Motor should draw low inrush current (Starting current,and if supply is interrupted and restore again.) 14)It should withstand for voltage fluctuation without affecting its performance. 15) It should have low initial cost. 16) It should have less maintenance cost. 17) It should have high efficiency. 18) It should have long life.

Related questions

Description : State any four desirable characteristics of ideal traction motor. State the names of different traction motor used.

Last Answer : Desirable characteristics of ideal traction motors:-  A) Mechanical Properties or characteristics: 1) It should be robust in construction to withstand against continuous vibrations. 2) Weight of motor per HP ... AC series motor 3. 3-Ph, Slip-ring induction motor 4. Linear induction motor (LIM)

Description : "DC series motor is used for traction purpose." Justify your answer with any six characteristics.

Last Answer : Due To Following Reasons DC Series Motor Is Used For Traction Purpose:- 1. DC Series motor robust in construction and capable to withstand against continuous vibration. 2. DC series motor weight is 1. ... . 12. Torque obtained by DC series motor is smooth and uniform, so it improves riding quality

Description : State eight requirements of an ideal traction system.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : Explain the suitability of 3-phase induction motor for traction service. 

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : State desirable properties of heating elements used in indirect resistance heating. 

Last Answer : Following properties of good heating material in indirect resistance heating:- 1. High resistivity: It should have high resistivity. So that it becomes compact in size and produces more heat with small ... , it should have low temperature co-efficient of resistance. 10.It should not be brittle.

Description :  State any eight advantages of electric heating.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : Explain the requirements of elevator motor. State with reason best suitable motor for elevator.

Last Answer : Ideal requirements of elevator motor: 1. High starting torque along with high rate of acceleration and retardation. 2. Motors are compact in size especially smaller in diameter. 3. Speed of motor should not exceed 900 ... 4. Permanent magnet AC Motor. 5. Split Phase AC I.M. 6. Capacitor Start I.M.

Description : Explain regenerative braking for D.C. series motor.

Last Answer : Schematic diagram of regenerative braking of D.C. series :-  Explanation of regenerative braking: During normal running, motors are connected in parallel with field winding in series ... For final stop mechanical braking is applied. External Resistances are connected to limit the current.

Description : Why noise of motor is produced? How it can be reduced?

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : The motor used for electric traction is  (1) D.C. shunt motor (3) D.C. series motor  (2) D.C. compound motor (4) Synchronous motor

Last Answer : The motor used for electric traction is D.C. series motor

Description : State the principle of induction heating. Write four applications of induction heating.

Last Answer : Principle of Induction heating: The basic principle of induction heating is that, supply is given to primary winding of furnace transformer & heat is produced in the secondary (charge) due to ... utilized to melt the charge. Where, R = Resistance of charge & I secondary current

Description : Q2. What are the desirable agronomic characteristics for crop improvement? -Science

Last Answer : The essential agronomic features required for crop improvement are: Profuse branching along with tallness in any fodder crop Dwarfness in any cereals

Description : The development of desirable person's characteristics is largely a matter of Options: A) Social pressures B) Habit-formation C) Motivation D) Opportunity for learning

Last Answer : C) Motivation

Description : State and explain the desirable characteristics of a Tariff. 

Last Answer : The desirable characteristics of a Tariff: 1. It should be easy to understand to consumer. 2. Easy to calculate. 3. Tariff should be attractive i.e. It should not be too high or ... industrial consumer, in addition to basic tariff incentives and penalty related to PF and LF should be considered.

Description : The desirable characteristics of a signal source are : - a) the frequency of the signal should be well known and stable b) the amplitude of the signal source should be controllable from very small to relatively large value c) The output signal should be free from distortion d) all the above

Last Answer : The desirable characteristics of a signal source are : - a) the frequency of the signal should be well known and stable b) the amplitude of the signal source should be controllable from very small to relatively large value c) The output signal should be free from distortion d) all the above

Description :  In measurement system, which of the following static characteristics is desirable ? a) accuracy b) sensitivity c) reproducibility d) all the above

Last Answer : d) all of the above

Last Answer : The desirable static characteristics of a measuring system are accuracy, sensitivity and reproducibility.

Description : What are the desirable characteristics of ideal switch?

Last Answer : Desirable characteristics of the ideal switch: It is desirable to have power switches characteristics closer to ideal switch. The ideal switch should have the following characteristics. Zero resistance when ... . 100% efficiency. Able to control power flow with zero power dissipation.

Description : Write down the circuit breaker with their rating used in traction substation. Explain any one.

Last Answer : Circuit Breaker With Their Rating Used in Traction Substation: Rated capacity of a circuit breaker is 750Amps at 25 kV, 500MVA. Its overall tripping time is 0.14 seconds composed of 0.04 ... but in case of traction substation application, mostly Minimum Oil Circuit Breaker (MOCB) is preferred.

Description : Write any four points that state how a traction transformer is different from ordinary transformer.

Last Answer : Ans: 1) Specially designed to withstand severe operating conditions.  2) Are required to have high short time peak capacity.  3) Class A insulation , specially reinforced to withstand frequent short circuits.  4) Can ... effect of SC impedance not less than 8.5 % for 10 MVA and 10 % for 12.5 MVA.

Description : Radiation characteristics of a dipole A. Figure of eight B. Omnidirectional C. Bidirectional D. Unidirectional

Last Answer : C. Bidirectional

Description : What are minerals ? For most of the part minerals are constituted of eight elements, name any six of them. State the six characteristics that are used to identify minerals

Last Answer : Minerals Natural substance belonging to a group of inorganic (often crystalline) compounds which are found in the earth, that which is not animal or vegetable A mineralis a naturally occurring substance ... transmit light. Depending on a number of things, rocks & minerals can also transmit light.

Description : Describe any eight characteristics of good stone masonry. 

Last Answer : The requirements of good stone masonry are as follows:- 1. The stones to be used for stone masonry should be hard, tough & durable. 2. The stone should be properly dressed as per the ... constructed perfectly in plumb. 11. The exposed joints of the masonry should be properly pointed by mortar.

Description : Applications of Dielectric Heating

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : Differentiate between core type and core less induction furnace.

Last Answer : Sr.No. Core type induction furnace. Core less induction furnace. 1 Less leakage flux  More leakage flux 2 Power factor is good Power factor is poor 3 ... normal frequency is used. Due to high frequency, high voltage supply, time required for heating is less.

Description :  Justify the use of saturable reactor to control the magnitude of welding current.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : Explain the factors affecting framing of tariffs.

Last Answer : Factors affecting framing of tariffs:- 1. Total recovery of all taxes , duties and other charges 2. Expenses on premium (installment) paid to insurance company. 3. T&D losses. 4. Electricity cannot ... L.F. 12. The tariff should be simple cheap and capable of easy explanation to consumers. 

Description : State four advantages of seam welding over spot welding.

Last Answer : Advantages of seam welding over spot welding:- 1. Due to seam welding we get continuous weld which is air-tight 2. Gas tight as well as liquid tight joints can be made. 3. The Overlap is ... . The production of single seam weld and parallel seams can be got simultaneously. 5. Efficient energy use.

Description : Explain with neat diagram construction and working of Ajax Wyatt vertical core induction furnace.

Last Answer : Neat sketch of Ajax Wyatt' vertical core furnace: Construction of Ajax Wyatt' vertical core furnace: Vertical core type induction heating furnace is nothing but transformer. It consists of ... is utilized to melt the charge. Where, R = Resistance of charge & I secondary current.

Description : Explain with the diagram butt welding. State its applications. 

Last Answer : Diagram butt welding:-  Explanation: Transformer used for welding is designed for low voltage and high current secondary. Transformer is oil cooled The job is clamped as shown in fig. two parts which ... : 1) For welding rod, wire, pipe etc 2) For joining thick metal plates or bars at end

Description : State its types electrical braking.

Last Answer : Types of Electrical Braking: Electrical braking system: 1. Plugging 2. Rheostatic (Dynamic) Braking 3. Regenerative Braking 4. Electromagnetic Braking 5. Eddy current braking

Description : Explain the factors to be considered while designing a lighting scheme.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : State any factors to be considered while selecting electrical welding system.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : State two advantages of P.F. tariff and TOD tariff for the power system concern

Last Answer : time of day tariff:_ In time of day tariff structure incentives for power draw during peak off hours & extra charges for power draw during peak hours are built in. advantages:- 1. TOD tariff encourage ... advantages:-  1. kva rating of equipment reduces 2.due to high p.f less electricity bill.

Description : State the four requirements of Tariff. 

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : State disadvantages of low power factor.

Last Answer : Due to low power factor The load draws high current. High cu losses. Efficiency decreases. Voltage regulation increases Temperature increases May break down  the insulation.

Description : Give classification of electrical welding.

Last Answer : i) Resistance Welding:- 1) Spot welding 2) Seam welding 3) Projection Welding 4) Butt Welding- i) Simple butt welding ii) Flash butt welding  ii) Arc welding:- 1) Carbon Arc Welding: a) shielded welding b) unshielded welding 2) Metal Arc Welding: a) shielded welding b) unshielded welding

Description : Compare individual and group drive on any four points.  

Last Answer : S.No. Point Individual Drive Group Drive 1 Definition In this type of drive each machine has its own separate electric drive (motor). It may be directly coupled ... Lathe Machine (Similar application will be consider) Textile Industry (Similar application will be consider)

Description : Compare between Resistance welding and Arc welding on any six points.

Last Answer : Sr.No Parameters Resistance Welding Arc Welding 1 Type of welding Plastic/Pressure/Non-fusion welding Fusion/Non pressure welding 2 Principle of heat developed Heat ... It is suitable for mass production It is suitable for heavy job, maintenance and repair work

Description : State the four causes of low (poor) power factor.

Last Answer : Following are the Causes of low power factor: - 1. Magnitude of Magnetizing Current :- As magnetizing current increases, power factor reduces. 2. Due to use of Induction Motor:- Most of industrial ... and maintenance:- P.f. falls if proper maintenance or repairs of equipments are not done. 

Description : State any two applications of each for the following types of electrical heating : (i) Direct resistance heating(ii) Indirect induction heating (iii) Direct.arc heating (iv) Dielectric heating

Last Answer : (i) Direct resistance heating:- 1. This type of heating used for industrial purpose 2. Salt bath heating: This utilized for the purpose of carbonizing, tempering, quenching and hardening of steel tools 3. ... purpose. 14)In foundry for heating of sand, core, which are used in molding processes.

Description : Describe with neat sketch operation of seam type resistance welding.

Last Answer : 1) Seam Welding its neat labelled sketch:  Explanation: Seam welding is nothing but series of continuous spot welding Working: Job is kept in between two electrodes under ... reached supply is cut down and external pressure is applied simultaneously across the job to complete weld.  

Description :  Describe the construction of high pressure mercury vapour lamp with neat sketch

Last Answer : Construction:-  It consists of an inner bulb generally of silicon, to withstand high temperatures. The bulb contains a small quantity of mercury and argon. It is protected by outer glass, this ... : The function of power factor improvement capacitor is to improve the power factor 0.5 to 0.95

Description : Draw a neat labelled block diagram of AC electric locomotive. State the function of each part.

Last Answer : labelled diagram ofAC electric locomotive:  Function of AC electric locomotive Parts: 1) Overhead contact wire: Supply of 1-ph, 25KV, 50Hz, AC is given to overhead conductor. 2) Current collecting ... mechanical power to run the train i.e. DC series motor which is used as traction motor.

Description : Compare DC and AC welding on any four points.

Last Answer : Points DC Welding AC Welding Supply equipment used  DC differential Compound Generator, or Rectifier Welding Transformer Heating Effect Uniform Not Uniform Temperature Obtain ... High, 85% Application Carbon Arc Welding Resistance Welding , Metal Arc Welding

Description : Compare Single phase 25 kV AC and 1500 V DC track electrification.

Last Answer : Points Single phase 25 kV AC track Electrification 1500 V DC track electrification Supply given to O/H condition 1-ph, 25KV, AC 50 Hz  600/750V-Tromways 1500/3000V urban/suburban ... track distance Less More Applications Main line services Urban and suburban area

Description : Advantages eddy current heating

Last Answer : 1) No heat transfer loss as heat is produced in job itself. So it has high efficiency. 2) As heat is produced in job itself so time required for heating is less. For e.g. in some ... or other special atmospheric condition where other methods are not possible. 9) It is clean and convenient method.

Description : State advantages and disadvantages of electric braking over mechanical braking.

Last Answer : Advantages: 1. It is most reliable braking system. 2. Breaking actuation time is small as higher value of braking retardation is obtained. 3. Electrical braking is smooth & gradual. 4. Life of ... energy is surplus. 4. Initial cost is more due to other control equipments & circuitry. 

Description : State the various types of welding.

Last Answer : i) Resistance Welding:- 1) Spot welding 2) Seam welding 3) Projection Welding 4) Butt Welding- i) Simple butt welding ii) Flash butt welding   ii) Arc welding:- 1) Carbon Arc Welding: a) shielded welding b) unshielded welding 2) Metal Arc Welding: a) shielded welding b) unshielded welding

Description : Define load equalisation for electric motors. Explain how it is obtained for electric motors.

Last Answer : Define load equalization for electric Motor: There are many types of load which are fluctuating in nature e.g. wood cutting m/c, Rolling mill. Etc. For such type of loads, load equalization is ... increases so cost of cable increases, Hence it is necessary to smooth out load fluctuations on motor.