State eight requirements of an ideal traction system.

State eight requirements of an ideal traction system.
by

2 Answers

Answer :

Ideal Traction system should processes following requirement:- 1. It should be Pollution free. 2. It should have low capital, Running and maintenance cost. 3. It should have quick starting time. 4. It should have high starting torque. 5. It should have high rate of acceleration & retardation. 6. Highest speeds are possible. 7. It should have easy speed control method. 8. Its braking system should be reliable and causes less wear. 9. It should have better riding quality (less vibration) 10. It should be free from unbalance forces i.e. coefficient of adhesion should be more. 11. It should have lower center of gravity. 12. The locomotive should be self-contained and able to run on any route 13. There should be no standby losses. 14. It should have high efficiency 15. Regenerative braking should be possible. 16. The wear caused on the track should be minimum. 17. Equipment should be capable of overloads for short periods. 18. Capability of withstanding voltage fluctuations. 19. Parallel running usually more than one motor (2 or 4 motors) should be possible. 20. Traction system should be clean & long life. 21. There should be no interference to the communication lines running along the lines.

by

Answer :

.embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }
by

Related questions

Write eight desirable characteristics of traction motor.

Description : Write eight desirable characteristics of traction motor.

Last Answer : Desirable characteristics of ideal traction motors:- 1) It should be robust in construction to withstand against continuous vibrations. 2) Weight of motor per HP should be minimum in order to increase pay ... maintenance cost. 17) It should have high efficiency. 18) It should have long life.

State any four desirable characteristics of ideal traction motor. State the names of different traction motor used.

Description : State any four desirable characteristics of ideal traction motor. State the names of different traction motor used.

Last Answer : Desirable characteristics of ideal traction motors:-  A) Mechanical Properties or characteristics: 1) It should be robust in construction to withstand against continuous vibrations. 2) Weight of motor per HP ... AC series motor 3. 3-Ph, Slip-ring induction motor 4. Linear induction motor (LIM)

Explain the suitability of 3-phase induction motor for traction service.

Description : Explain the suitability of 3-phase induction motor for traction service. 

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

"DC series motor is used for traction purpose." Justify your answer with any six characteristics.

Description : "DC series motor is used for traction purpose." Justify your answer with any six characteristics.

Last Answer : Due To Following Reasons DC Series Motor Is Used For Traction Purpose:- 1. DC Series motor robust in construction and capable to withstand against continuous vibration. 2. DC series motor weight is 1. ... . 12. Torque obtained by DC series motor is smooth and uniform, so it improves riding quality

State any eight advantages of electric heating.

Description :  State any eight advantages of electric heating.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Explain the requirements of elevator motor. State with reason best suitable motor for elevator.

Description : Explain the requirements of elevator motor. State with reason best suitable motor for elevator.

Last Answer : Ideal requirements of elevator motor: 1. High starting torque along with high rate of acceleration and retardation. 2. Motors are compact in size especially smaller in diameter. 3. Speed of motor should not exceed 900 ... 4. Permanent magnet AC Motor. 5. Split Phase AC I.M. 6. Capacitor Start I.M.

State the four requirements of Tariff.

Description : State the four requirements of Tariff. 

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

An ideal traction system should have?

Last Answer : An ideal traction system should have easy speed control, high starting tractive effort, equipment capable of with standing large temporary loads.

A power tiller is most suited for rotary cultivation because: A. It generates negative draft B. Its traction requirements are low C. It provides high degree of soil pulverization D. All of the above

Description : A power tiller is most suited for rotary cultivation because: A. It generates negative draft B. Its traction requirements are low C. It provides high degree of soil pulverization D. All of the above

Last Answer : D. All of the above

State any four ideal requirements of signaling system.

Description : State any four ideal requirements of signaling system.

Last Answer : i) Unless the whole section of track governed by the signal is clear & safe, it should not be possible to display safe' indication. ii) Failure of any component of signaling scheme should give danger ... shall be provided in the same track space for at least 600m in the rear of the signal.

State any factors to be considered while selecting electrical welding system.

Description : State any factors to be considered while selecting electrical welding system.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

State two advantages of P.F. tariff and TOD tariff for the power system concern

Description : State two advantages of P.F. tariff and TOD tariff for the power system concern

Last Answer : time of day tariff:_ In time of day tariff structure incentives for power draw during peak off hours & extra charges for power draw during peak hours are built in. advantages:- 1. TOD tariff encourage ... advantages:-  1. kva rating of equipment reduces 2.due to high p.f less electricity bill.

India has eight coastal states but more than half the sea salt is made along the Gujarat coast because (a) Gandhiji started the salt movement in Gujarat (b) Low rainfall and relative humidity are ideal for the production of salt through evaporation of sea water (c) Kandla port exports salt (d) The salinity of sea water is very high near the Gujarat coast

Description : India has eight coastal states but more than half the sea salt is made along the Gujarat coast because (a) Gandhiji started the salt movement in Gujarat (b) Low rainfall and relative humidity are ideal ... ) Kandla port exports salt (d) The salinity of sea water is very high near the Gujarat coast

Last Answer : Ans: (b)

State any two requirements of a Ideal road alignment

Description : State any two requirements of a Ideal road alignment

Last Answer : a) Crossing: The provision of railway and road crossing should be properly studied. Dangerous road and rail crossing should be avoided. b) Proper drainage: The provision of proper and ... ) The alignment should pass through regions of natural beauty and scenery to have good natural aspects

All elements of the marketing mix are influenced by physical distribution functions. For this reason, it is important for marketers to remember that A)physical distribution decisions must be made prior to any other marketing strategy consideration. B)physical distribution costs often rise as customer service requirements decrease. C)over 75 percent of all marketing costs are associated with physical distribution expenditures. D)no single distribution system is ideal for all situations and target markets.

Description : All elements of the marketing mix are influenced by physical distribution functions. For this reason, it is important for marketers to remember that A)physical distribution decisions must be made ... expenditures. D)no single distribution system is ideal for all situations and target markets.

Last Answer : D)no single distribution system is ideal for all situations and target markets.

With respect to LIM propelled railway traction system state points of; i) Strengths of LIM ii) Weaknesses of LIM

Description : With respect to LIM propelled railway traction system state points of; i) Strengths of LIM ii) Weaknesses of LIM

Last Answer : Strengths of LIM propelled railway traction: 1) Pull produced for propelling the system is independent of adhesion between the wheels of motorized coach and rail. 2) No driving wheels and hence no ... traction is single phase ac power inverters are needed for operation of LIM this adds to cost.

State four advantages of seam welding over spot welding.

Description : State four advantages of seam welding over spot welding.

Last Answer : Advantages of seam welding over spot welding:- 1. Due to seam welding we get continuous weld which is air-tight 2. Gas tight as well as liquid tight joints can be made. 3. The Overlap is ... . The production of single seam weld and parallel seams can be got simultaneously. 5. Efficient energy use.

State desirable properties of heating elements used in indirect resistance heating.

Description : State desirable properties of heating elements used in indirect resistance heating. 

Last Answer : Following properties of good heating material in indirect resistance heating:- 1. High resistivity: It should have high resistivity. So that it becomes compact in size and produces more heat with small ... , it should have low temperature co-efficient of resistance. 10.It should not be brittle.

Explain with the diagram butt welding. State its applications.

Description : Explain with the diagram butt welding. State its applications. 

Last Answer : Diagram butt welding:-  Explanation: Transformer used for welding is designed for low voltage and high current secondary. Transformer is oil cooled The job is clamped as shown in fig. two parts which ... : 1) For welding rod, wire, pipe etc 2) For joining thick metal plates or bars at end

State its types electrical braking.

Description : State its types electrical braking.

Last Answer : Types of Electrical Braking: Electrical braking system: 1. Plugging 2. Rheostatic (Dynamic) Braking 3. Regenerative Braking 4. Electromagnetic Braking 5. Eddy current braking

State disadvantages of low power factor.

Description : State disadvantages of low power factor.

Last Answer : Due to low power factor The load draws high current. High cu losses. Efficiency decreases. Voltage regulation increases Temperature increases May break down  the insulation.

State the four causes of low (poor) power factor.

Description : State the four causes of low (poor) power factor.

Last Answer : Following are the Causes of low power factor: - 1. Magnitude of Magnetizing Current :- As magnetizing current increases, power factor reduces. 2. Due to use of Induction Motor:- Most of industrial ... and maintenance:- P.f. falls if proper maintenance or repairs of equipments are not done. 

State any two applications of each for the following types of electrical heating : (i) Direct resistance heating(ii) Indirect induction heating (iii) Direct.arc heating (iv) Dielectric heating

Description : State any two applications of each for the following types of electrical heating : (i) Direct resistance heating(ii) Indirect induction heating (iii) Direct.arc heating (iv) Dielectric heating

Last Answer : (i) Direct resistance heating:- 1. This type of heating used for industrial purpose 2. Salt bath heating: This utilized for the purpose of carbonizing, tempering, quenching and hardening of steel tools 3. ... purpose. 14)In foundry for heating of sand, core, which are used in molding processes.

Draw a neat labelled block diagram of AC electric locomotive. State the function of each part.

Description : Draw a neat labelled block diagram of AC electric locomotive. State the function of each part.

Last Answer : labelled diagram ofAC electric locomotive:  Function of AC electric locomotive Parts: 1) Overhead contact wire: Supply of 1-ph, 25KV, 50Hz, AC is given to overhead conductor. 2) Current collecting ... mechanical power to run the train i.e. DC series motor which is used as traction motor.

State advantages and disadvantages of electric braking over mechanical braking.

Description : State advantages and disadvantages of electric braking over mechanical braking.

Last Answer : Advantages: 1. It is most reliable braking system. 2. Breaking actuation time is small as higher value of braking retardation is obtained. 3. Electrical braking is smooth & gradual. 4. Life of ... energy is surplus. 4. Initial cost is more due to other control equipments & circuitry. 

State the various types of welding.

Description : State the various types of welding.

Last Answer : i) Resistance Welding:- 1) Spot welding 2) Seam welding 3) Projection Welding 4) Butt Welding- i) Simple butt welding ii) Flash butt welding   ii) Arc welding:- 1) Carbon Arc Welding: a) shielded welding b) unshielded welding 2) Metal Arc Welding: a) shielded welding b) unshielded welding

State the principle of induction heating. Write four applications of induction heating.

Description : State the principle of induction heating. Write four applications of induction heating.

Last Answer : Principle of Induction heating: The basic principle of induction heating is that, supply is given to primary winding of furnace transformer & heat is produced in the secondary (charge) due to ... utilized to melt the charge. Where, R = Resistance of charge & I secondary current

State the factors to be considered for selection of shape and size of the car of elevator.

Description : State the factors to be considered for selection of shape and size of the car of elevator.

Last Answer : The size and shape of elevator car depends on following factors:  i) No. of passenger to be carried: While selecting the size of car it is a usual practice to allow. A Space of 2 Sq. ... of elevator depends on space available in building.  iii) Type of building  iv) Application of elevator

State the causes of failure of heating element.

Description : State the causes of failure of heating element.

Last Answer : Following of the different causes of failure of heating element:  i) Formation of hot spot: Hot spot on heating element is the point which is at higher temperature than remaining heating element ... & cooling of heating element, it may break (fail) due to small mechanical injury also.

In your ideal apartment or house, what would be your minimum requirements as far as appliances or other features?

Description : In your ideal apartment or house, what would be your minimum requirements as far as appliances or other features?

Last Answer : Ideal would be: Full size washer/dryer in a separate laundry room with counter for folding. Six burner gas stove with full oven. Dishwasher. Bread warming drawer. Separate oven for keeping prepared ... half bath off of living room/social area, another off of kitchen, and one with outside access.

Digital evidence must follow the requirements of the …….. a. Ideal evidence b. Best evidence c. Exchange evidence d. All of the mentioned

Description : Digital evidence must follow the requirements of the …….. a. Ideal evidence b. Best evidence c. Exchange evidence d. All of the mentioned

Last Answer : b. Best evidence

Write any four points that state how a traction transformer is different from ordinary transformer.

Description : Write any four points that state how a traction transformer is different from ordinary transformer.

Last Answer : Ans: 1) Specially designed to withstand severe operating conditions.  2) Are required to have high short time peak capacity.  3) Class A insulation , specially reinforced to withstand frequent short circuits.  4) Can ... effect of SC impedance not less than 8.5 % for 10 MVA and 10 % for 12.5 MVA.

For a traction transformer circuit breaker state: 1) Rated current and rupturing capacity 2) Any two tests it should be capable of withstanding 3) Overall tripping time and relay time.

Description : For a traction transformer circuit breaker state: 1) Rated current and rupturing capacity 2) Any two tests it should be capable of withstanding 3) Overall tripping time and relay time.

Last Answer : Ans: 1) Rated current --- 750 A and Rupturing capacity --- 500 MVA  2) Any two tests it should be capable of withstanding --- Breaking test , Reclosing test , Endurance test ( any two )  3) Overall tripping time --- 0.14 sec and Relay time --- 0.04 sec 

State use of any four relays for the protection of traction transformer.

Description : State use of any four relays for the protection of traction transformer. 

Last Answer : Relays for the protection of traction transformers:  Inverse time over current relay as back up protection on primary (HV side) - over current protection of transformer and other equipment.  ... .  Buchholz relay - protection from incipient earth or inter winding faults inside the transformer

List any four weaknesses of LIM propelled railway traction system.

Description : List any four weaknesses of LIM propelled railway traction system.

Last Answer : Weaknesses of LIM Propelled Railway Traction System: 1. The system requires looping of all reaction rails all along the route. This considerably adds to the cost of track. 2. Since Al is relative ... in the magnetic and electric circuits at entry and exit ends of motor, poor motor efficiency.

Draw a neat labeled diagram to show protective system for AC traction and give the function of each relay used in it.

Description : Draw a neat labeled diagram to show protective system for AC traction and give the function of each relay used in it. 

Last Answer : Protective system for AC traction:  Function Of Each Relay: For transformer -  Inverse time over current relay- as back up protection on primary (HV side) over current ... against faults near substation  Under voltage relay - protection against faults far away from substation

In quadrilateral speed-time curve of electric traction system, the accelerations during successive time periods

Description : In quadrilateral speed-time curve of electric traction system, the accelerations during successive time periods are ______ respectively.  (A) positive, negative and negative (B) positive, zero and negative (C) positive, positive and negative (D) positive, negative and zero

Last Answer : In quadrilateral speed-time curve of electric traction system, the accelerations during successive time periods are positive, negative and negative respectively. 

Applications of Dielectric Heating

Description : Applications of Dielectric Heating

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Differentiate between core type and core less induction furnace.

Description : Differentiate between core type and core less induction furnace.

Last Answer : Sr.No. Core type induction furnace. Core less induction furnace. 1 Less leakage flux  More leakage flux 2 Power factor is good Power factor is poor 3 ... normal frequency is used. Due to high frequency, high voltage supply, time required for heating is less.

Justify the use of saturable reactor to control the magnitude of welding current.

Description :  Justify the use of saturable reactor to control the magnitude of welding current.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Explain the factors affecting framing of tariffs.

Description : Explain the factors affecting framing of tariffs.

Last Answer : Factors affecting framing of tariffs:- 1. Total recovery of all taxes , duties and other charges 2. Expenses on premium (installment) paid to insurance company. 3. T&D losses. 4. Electricity cannot ... L.F. 12. The tariff should be simple cheap and capable of easy explanation to consumers. 

Explain with neat diagram construction and working of Ajax Wyatt vertical core induction furnace.

Description : Explain with neat diagram construction and working of Ajax Wyatt vertical core induction furnace.

Last Answer : Neat sketch of Ajax Wyatt' vertical core furnace: Construction of Ajax Wyatt' vertical core furnace: Vertical core type induction heating furnace is nothing but transformer. It consists of ... is utilized to melt the charge. Where, R = Resistance of charge & I secondary current.

Explain regenerative braking for D.C. series motor.

Description : Explain regenerative braking for D.C. series motor.

Last Answer : Schematic diagram of regenerative braking of D.C. series :-  Explanation of regenerative braking: During normal running, motors are connected in parallel with field winding in series ... For final stop mechanical braking is applied. External Resistances are connected to limit the current.

Explain the factors to be considered while designing a lighting scheme.

Description : Explain the factors to be considered while designing a lighting scheme.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Give classification of electrical welding.

Description : Give classification of electrical welding.

Last Answer : i) Resistance Welding:- 1) Spot welding 2) Seam welding 3) Projection Welding 4) Butt Welding- i) Simple butt welding ii) Flash butt welding  ii) Arc welding:- 1) Carbon Arc Welding: a) shielded welding b) unshielded welding 2) Metal Arc Welding: a) shielded welding b) unshielded welding

Why noise of motor is produced? How it can be reduced?

Description : Why noise of motor is produced? How it can be reduced?

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Compare individual and group drive on any four points.

Description : Compare individual and group drive on any four points.  

Last Answer : S.No. Point Individual Drive Group Drive 1 Definition In this type of drive each machine has its own separate electric drive (motor). It may be directly coupled ... Lathe Machine (Similar application will be consider) Textile Industry (Similar application will be consider)

Compare between Resistance welding and Arc welding on any six points.

Description : Compare between Resistance welding and Arc welding on any six points.

Last Answer : Sr.No Parameters Resistance Welding Arc Welding 1 Type of welding Plastic/Pressure/Non-fusion welding Fusion/Non pressure welding 2 Principle of heat developed Heat ... It is suitable for mass production It is suitable for heavy job, maintenance and repair work

Describe with neat sketch operation of seam type resistance welding.

Description : Describe with neat sketch operation of seam type resistance welding.

Last Answer : 1) Seam Welding its neat labelled sketch:  Explanation: Seam welding is nothing but series of continuous spot welding Working: Job is kept in between two electrodes under ... reached supply is cut down and external pressure is applied simultaneously across the job to complete weld.  

Describe the construction of high pressure mercury vapour lamp with neat sketch

Description :  Describe the construction of high pressure mercury vapour lamp with neat sketch

Last Answer : Construction:-  It consists of an inner bulb generally of silicon, to withstand high temperatures. The bulb contains a small quantity of mercury and argon. It is protected by outer glass, this ... : The function of power factor improvement capacitor is to improve the power factor 0.5 to 0.95