Description : Which of the manufacturing processes is/are required to make a typical stainless steel spoon out of sheet metal? A. Casting B. Forming C. Brazing D. Blow moulding
Last Answer : Forming
Description : Pick out the wrong statement. (A) Both annealing and normalising release the internal stresses of the material besides improving the mechanical properties (B) Low carbon steel does not respond to ... are also used for surface hardening (D) Martempering of a material is a hardening process
Last Answer : Option C
Description : Which of the following is not Powder-Based RP system? a.Selective Laser Sintering (SLS) b.Solid Object Ultraviolet-Laser Printer (SOUP) c.Electron Beam Melting (EBM) d.Direct Metal Deposition (DMD)
Last Answer : b.Solid Object Ultraviolet-Laser Printer (SOUP)
Description : Of all of the current material addition rapid prototyping technologies, which one is the mostwidely used? a.Ballistic particle manufacturing b.Selective laser sintering c.Solid ground curing d.Stereolithography
Last Answer : d.Stereolithography
Description : Which one of the following RP technologies uses solid sheet stock as the starting material? a.Droplet deposition manufacturing b.Fused-deposition modeling c.Laminated-Object Manufacturing d.Selective Laser Sintering
Last Answer : c.Laminated-Object Manufacturing
Description : Which of the following RP technologies uses powders as the starting material? a.Droplet Deposition Manufacturing b.Fused-Deposition Modeling c.Selective Laser Sintering d.Stereolithography
Last Answer : c.Selective Laser Sintering
Description : Reverberatory furnace is used for (A) Roasting/reduction of ores (B) Annealing steel coil (C) Heating air (D) Steel melting
Last Answer : (A) Roasting/reduction of ores
Description : Which of the following heat treatment processes is used for softening the hardened material? (A) Normalising (B) Tempering (C) Annealing (D) None of these
Last Answer : (B) Tempering
Description : Which of the following heat treatment processes is usually applied to castings? (A) Tempering (B) Annealing (C) Normalising (D) Carburising
Last Answer : (D) Carburising
Description : Pick out the wrong statement. (A) A soft magnetic material should have high permeability and small area of hysteresis loop (B) Poisson's ratio of high melting point metals is more than unity (C) ... less than 185°C (D) Steel produced by B.O.F process is ideally suited for manufacturing flat product
Last Answer : Option B
Description : Which is a continuous furnace? (A) Coke ovens (B) Annealing furnace (C) Glass tank furnace
Last Answer : (C) Glass tank furnace
Description : The process of heating the cold pressed metallic powder is called __________ in powder metallurgy. (A) Precipitation (B) Fusion (C) Sintering (D) Agglomeration
Last Answer : (C) Sintering
Description : Stresses encountered in the metal forming processes are less than the __________ of the material. (A) Fracture strength (B) Yield strength (C) Elastic limit (D) Limit of proportionality
Last Answer : Option A
Description : What is meant by annealing of glass? Explain
Last Answer : The process of gradual cooling of glass articles to room temperature is called annealing. Glass articles are allowed to cool gradually to room temperature by passing through different chambers with decreasing temperature.
Description : In the process of Selective Laser Sintering, raw material used is in the form of ______ a.machining wax b.foam core c.powder d.rubber
Last Answer : c.powder
Description : Which of the following process is not formative process? a.Bending b.Plastic injection molding c.Selective Laser Sintering d.Forging
Description : The following are true about blood-brain barrier: a. it is permeable at birth b. it involves tight junction between endothelial cells and end feet processes of astrocytes c. it is absent in the posterior pituitary d. all above
Last Answer : all above
Description : Pick out the wrong statement. (A) Minimum number of degree of freedom of a system is zero (B) Degree of freedom of a system containing a gaseous mixture of helium, carbon ... ) Enthalpy and internal energy change is zero during phase change processes like melting, vaporisation and sublimation
Last Answer : (D) Enthalpy and internal energy change is zero during phase change processes like melting, vaporisation and sublimation
Description : _________ does not change during phase transformation processes like sublimation, melting & vaporisation. (A) Entropy (B) Gibbs free energy (C) Internal energy (D) All (A), (B) & (C)
Last Answer : (B) Gibbs free energy
Description : Which one is not an induced draught furnace? (A) Blast furnace stove (B) Sintering furnace (C) High pressure boiler (D) None of these
Last Answer : (A) Blast furnace stove
Description : Which of the following is not a directly fired furnace? (A) By-product coke oven (B) Calcination kiln (C) Sintering furnace (D) Open hearth furnace
Last Answer : (A) By-product coke oven
Description : In which of the following furnaces, the gases are sucked through the stock bed from below? (A) Soaking pit (B) Sintering machine (C) Beehive oven (D) None of these
Last Answer : (B) Sintering machine
Description : A catalyst loses its activity due to (A) Loss in surface area of the active component (B) Agglomeration of metal particles caused by thermal sintering of the solid surface (C) Covering of the catalytic active sites by a foreign substance (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Temperature during hydrogenation of oil should not be more than 200°C, otherwise it will result in (A) Pyrolysis of oil (B) Sintering of porous catalyst (C) Hydrogen embrittlement (D) All (A), (B) and (C)
Description : Steel balls are manufactured by (A) Sintering (B) Casting (C) Cold heading (D) Spinning
Last Answer : (C) Cold heading
Description : Basic oxide is absent in __________ glass. (A) Flint (B) Pyrex (C) Quartz (D) All (A), (B) & (C)
Last Answer : (C) Quartz
Description : The heat treatment process applied to cold formed steel parts is (A) Normalising (B) Tempering (C) Artificial ageing (D) Solution annealing
Last Answer : (D) Solution annealing
Description : The heat treatment process to which castings and the steel balls produced by cold heading are subjected is (A) Tempering (B) Normalising (C) Annealing (D) None of these
Last Answer : (B) Normalising
Description : __________ is not a case hardening process. (A) Carburising (B) Nitriding (C) Cyaniding (D) Annealing
Last Answer : (D) Annealing
Description : Nitriding of steel is a process for (A) Case hardening (B) Spheroidising (C) Normalising (D) Annealing
Last Answer : (A) Case hardening
Description : Globular form of cementite is formed during the __________ process. (A) Spheroidising (B) Hardening (C) Annealing (D) Normalising
Last Answer : (B) Hardening
Description : Spheroidising of a material is a/an __________ process. (A) Normalising (B) Annealing (C) Tempering (D) Hardening
Last Answer : (B) Annealing
Description : Which one of the following is not Extrusion-Based RP Systems? a.Fused Deposition Modelling (FDM) b.3D Printing c.Sheet Lamination (Laminated Object Manufacturing (LOM)) d.Electron Beam melting (EBM)
Last Answer : d.Electron Beam melting (EBM)
Description : Which of the following is not Solid-based RP system? a.Laminated Object Manufacturing (LOM) b.Paper Lamination Technology (PLT) c.Electron Beam Melting (EBM) d.Fused Deposition Modeling (FDM)
Last Answer : c.Electron Beam Melting (EBM)
Description : Which method, vapor phase oxidation or direct-melt process, transforms deposited material into a solid glass preform by heating the porous material without melting?
Last Answer : Vapor phase oxidation.
Description : Drilling, milling and threading are examples of which kind of processes? a.Additive manufacturing b.Subtractive manufacturing c.Formative manufacturing d.None of the above
Last Answer : b.Subtractive manufacturing
Description : What manufacturing processes were applied to SS Forged Fittings?
Last Answer : There are four processes of manufacturing a SS forged fittings. First is Mandrel method, as the name suggests a curved mandrel is inserted into a length of pipe. Extrusion Method consists of a machine that ... a piece of pipe goes through a mould of the fittings and come out in the needed shape.
Description : Which of the following information systems focuses on making manufacturing processes more efficient and of higher quality? a) Computer aided manufacturing b) Computer integrated manufacturing c) Computer aided software engineering d) Computer aided system engineering e) None of these
Last Answer : a) Computer aided manufacturing
Description : Classify various Manufacturing Processes.
Last Answer : The Four main types of Manufacturing Processes are (1) Casting & Molding, (2) Machining, (3) Joining & Shearing and (4) Forming.
Description : Explicit support structures are not required in Selective Laser Sintering (SLS). a.TRUE b.FALSE c. d.
Last Answer : a.TRUE
Description : In Selective Laser Sintering, laser light is also being used. a.TRUE b.FALSE c. d.
Description : Which of the following RP technologies uses molten material as the starting material? a.Three-Dimensional Printing b.Fused-Deposition Modeling c.Stereolithography d.Selective Laser Sintering
Last Answer : c.Stereolithography
Description : Which of the following is used as base material in Selective laser sintering (SLS)? a.Photopolymer b.Thermoplastics, Metal powders c.Titanium alloys d.Various materials
Last Answer : b.Thermoplastics, Metal powders
Description : Which of the following RP system is not developed by 3D systems? a.Selective Laser Sintering (SLS) b.Multi-Jet Modeling System (MJM) c.Paper Lamination Technology (PLT) d.Stereolithography Apparatus (SLA)
Last Answer : c.Paper Lamination Technology (PLT)
Description : __________ moulding is used for shaping of thermosetting plastics exclusively. (A) Compression (B) Injection (C) Transfer (D) Extrusion
Last Answer : (C) Transfer
Description : Annealing process is
Last Answer : Annealing process is A. heating the steel bright red and then cooling suddenly B. heating the steel ... charcol D. heating the rods of iron in ammonia
Description : In order to prevent the corrosion of iron pipes they are often coated with a layer of zinc. This process is termed as: A. Electroplating B. Annealing C. Galvanization D. Vulcanization
Last Answer : ANSWER: C
Description : In order to prevent the corrosion of iron pipes, they are often coated with a layer of zinc. This process is termed as (a) electroplating (b) annealing (c) galvanization (d) vulcanization
Last Answer : Ans:(c)
Description : A process of very slow regulated cooling is known as (a) Quenching (b) Sedimentation (c) Annealing (d) Diffusion
Description : In order to prevent the corrosion of iron pipes they are often coated with a layer of zinc. This process is termed as------? A. Electroplating B. Annealing C. Galvanization (Answer) D. Vulcanization
Last Answer : C. Galvanization (Answer)