The ratio of moles of a reactant converted into the desired product to that converted into unwanted product is called (A) Operational yield (B) Relative yield (C) Selectivity (D) None of these

The ratio of moles of a reactant converted into the desired product to
that converted into unwanted product is called
(A) Operational yield
(B) Relative yield
(C) Selectivity
(D) None of these
by

1 Answer

Answer :

(C) Selectivity
by

Related questions

When all the limiting reactant is consumed in the reaction, the operational yield __________ the relative yield. (A) Is greater than (B) Is smaller than (C) Equals (D) Can be either greater or smaller than (depends on the type of reaction)

Description : When all the limiting reactant is consumed in the reaction, the operational yield __________ the relative yield. (A) Is greater than (B) Is smaller than (C) Equals (D) Can be either greater or smaller than (depends on the type of reaction)

Last Answer : (C) Equals

For reactions in parallel viz A → P (desired product) and A → Q (unwanted product), if the order of the desired reaction is higher than that of the undesired reaction, a (A) Batch reactor is preferred over a single CSTR for high yield (B) Tubular reactor is preferred over a single CSTR for high yield (C) Both (A) and (B) (D) Single CSTR is the most suitable

Description : For reactions in parallel viz A → P (desired product) and A → Q (unwanted product), if the order of the desired reaction is higher than that of the undesired reaction, a (A) Batch reactor is preferred over a ... a single CSTR for high yield (C) Both (A) and (B) (D) Single CSTR is the most suitable

Last Answer : (C) Both (A) and (B)

_________ is defined as the geometric mean of the relative rejections and the relative recoveries of two minerals. (A) Separation efficiency (B) Selectivity index (C) Concentration ratio (D) None of these

Description : _________ is defined as the geometric mean of the relative rejections and the relative recoveries of two minerals. (A) Separation efficiency (B) Selectivity index (C) Concentration ratio (D) None of these

Last Answer : (B) Selectivity index

Rate constant for a first order reaction does not depend upon reaction time, extent of reaction and the initial concentration of reactants; but it is afunction of reaction temperature. In a chemical reaction, the time requiredto reduce the concentration of reactant from 100 gm moles/litre to 50 gmmoles/litre is same as that required to reduce it from 2 gm moles/litre to 1gm mole/litre in the same volume. Then the order of this reaction is:(A) 0(B) 1(C) 2(D) 3

Description : Rate constant for a first order reaction does not depend upon reaction time, extent of reaction and the initial concentration of reactants; but it is afunction of reaction temperature. In a chemical reaction, the time required to ... Then the order of this reaction is: (A) 0 (B) 1 (C) 2 (D) 3

Last Answer : (B) 1

What is the unit of the rate constant in a chemical reaction in which 10% of the reactant decomposes in one hour, 20% in two hours, 30% in three hours and so on? (A) Litre/mole.second (B) Moles/litre.second (C) Litre/mole (D) Litre/second

Description : What is the unit of the rate constant in a chemical reaction in which 10% of the reactant decomposes in one hour, 20% in two hours, 30% in three hours and so on? (A) Litre/mole.second (B) Moles/litre.second (C) Litre/mole (D) Litre/second

Last Answer : (A) Litre/mole.second

Concentration of the limiting reactant (with initial concentration of a moles/litre) after time t is (a-x). Then 't' for a first order reaction is given by (A) k. t = ln a/(a - x) (B) k. t = x/a (a - x) (C) k. t = ln (a - x)/a (D) k. t = ln a (a - x)/x

Description : Concentration of the limiting reactant (with initial concentration of a moles/litre) after time t is (a-x). Then 't' for a first order reaction is given by (A) k. t = ln a/(a - x) (B) k. t = x/a (a - x) (C) k. t = ln (a - x)/a (D) k. t = ln a (a - x)/x

Last Answer : (A) k. t = ln a/(a - x)

In a first order reaction, the time required to reduce the concentration of reactant from 1 mole/litre to 0.5 mole/litre will be __________ that requiredto reduce it from 10 moles/litre to 5 moles/litre in the same volume.(A) More than(B) Less than(C) Same as(D) Data insufficient; can't be predicted

Description : In a first order reaction, the time required to reduce the concentration of reactant from 1 mole/litre to 0.5 mole/litre will be __________ that requiredto reduce it from 10 moles/litre to 5 moles/litre in the ... (A) More than (B) Less than (C) Same as (D) Data insufficient; can't be predicted

Last Answer : (C) Same as

An unwanted plant, growing where it is not desired?

Description : An unwanted plant, growing where it is not desired?

Last Answer : Ans.Weed

What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Description : What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Last Answer : C. 125,000

What term is used to describe the frequency at which the filter circuit changes from the point of rejecting the unwanted frequencies to the point of passing the desired frequencies?

Description : What term is used to describe the frequency at which the filter circuit changes from the point of rejecting the unwanted frequencies to the point of passing the desired frequencies?

Last Answer : Frequency cutoff (fco).

How do you find the number of moles for this reactant.

Description : How do you find the number of moles for this reactant.

Last Answer : Homework. :P

The reciprocal of stripping factor is termed as (A) Selectivity index (B) Relative volatility (C) Absorption factor (D) Murphree efficiency

Description : The reciprocal of stripping factor is termed as (A) Selectivity index (B) Relative volatility (C) Absorption factor (D) Murphree efficiency

Last Answer : (C) Absorption factor

The expression, y(1 - x)/x(1 - y) is for (A) Absorption factor (B) Relative volatility (C) Selectivity (D) Murphree efficiency

Description : The expression, y(1 - x)/x(1 - y) is for (A) Absorption factor (B) Relative volatility (C) Selectivity (D) Murphree efficiency

Last Answer : (B) Relative volatility

Separation of two volatile liquids by distillation makes use of their (A) Selectivity (B) Relative volatility (C) Solubility (D) Density difference

Description : Separation of two volatile liquids by distillation makes use of their (A) Selectivity (B) Relative volatility (C) Solubility (D) Density difference

Last Answer : (B) Relative volatility

The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the throttle control circuit B. feedback resistor of the summing amplifier circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit

Description : The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the ... circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit

Last Answer : Answer: A

To obtain the desired data in a study, which of the following types of definition is most essential? a. Theoretical b. Conceptual c. Operational d. Dictionary

Description : To obtain the desired data in a study, which of the following types of definition is most essential? a. Theoretical b. Conceptual c. Operational d. Dictionary

Last Answer : c. Operational

The unwanted amino acids abstracted from the tissues are either used up by the tissue or in the liver converted into (A) Ammonia (B) Urea (C) Ammonium salts (D) Uric acid

Description : The unwanted amino acids abstracted from the tissues are either used up by the tissue or in the liver converted into (A) Ammonia (B) Urea (C) Ammonium salts (D) Uric acid

Last Answer : Answer : B

How do you convert recipes to yield smaller and larger quantities based on operational needs?

Description : How do you convert recipes to yield smaller and larger quantities based on operational needs?

Last Answer : Need answer

The reflux to a distillation column is 100 moles/hr, when the overhead product rate is 50 moles/hr. The reflux ratio is (A) 2 (B) 0.5 (C) 50 (D) 150

Description : The reflux to a distillation column is 100 moles/hr, when the overhead product rate is 50 moles/hr. The reflux ratio is (A) 2 (B) 0.5 (C) 50 (D) 150

Last Answer : (A) 2

The rate constant of a first order reaction depends on the (A) Concentration of the reactant (B) Temperature (C) Concentration of the product (D) Time

Description : The rate constant of a first order reaction depends on the (A) Concentration of the reactant (B) Temperature (C) Concentration of the product (D) Time

Last Answer : (B) Temperature

6 gm of carbon is burnt with an amount of air containing 18 gm oxygen. The product contains 16.5 gms CO2 and 2.8 gms CO besides other constituents. What is the degree of conversion on the basis of disappearance of limiting reactant? (A) 100% (B) 95% (C) 75% (D) 20%

Description : 6 gm of carbon is burnt with an amount of air containing 18 gm oxygen. The product contains 16.5 gms CO2 and 2.8 gms CO besides other constituents. What is the degree of conversion on the basis of disappearance of limiting reactant? (A) 100% (B) 95% (C) 75% (D) 20%

Last Answer : (B) 95%

Cyclohexanol can be converted into cyclohexylamine by following two routes. Which of the following methods is expected to give good yield of cyclohexy

Description : Cyclohexanol can be converted into cyclohexylamine by following two routes. Which of the following methods is expected to give good yield of cyclohexy

Last Answer : Cyclohexanol can be converted into cyclohexylamine by following two routes. Which of the following methods ... equally suitable D. neither of the two

A typical objective of an operational audit is for the auditor to a. Determine whether the financial statements fairly present the entity's operations. b. Evaluate the feasibility of attaining the entity's operational objectives. c. Make recommendation for improving performance. d. Report on the entity's relative success in maximizing profits

Description : A typical objective of an operational audit is for the auditor to a. Determine whether the financial statements fairly present the entity's operations. b. Evaluate the feasibility of ... recommendation for improving performance. d. Report on the entity's relative success in maximizing profits

Last Answer : Make recommendation for improving performance

Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Description : Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Last Answer : A. increases sensitivity to weak signals

What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Description : What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Last Answer : C. Poor front-end selectivity

In catalytic alkylation, higher iso-butane to olefin ratio gives (A) Low final boiling point product (B) Higher yield (C) Both (A) and (B) (D) Neither (A) nor (B

Description : In catalytic alkylation, higher iso-butane to olefin ratio gives (A) Low final boiling point product (B) Higher yield (C) Both (A) and (B) (D) Neither (A) nor (B

Last Answer : (A) Low final boiling point product

For series reaction, the relative yield (A) Is always greater for plug-flow reactor than for the single CSTR of the same volume (B) Statement in (A) is wrong (C) Decreases with increasing conversion (D) Both (A) and (C) hold good

Description : For series reaction, the relative yield (A) Is always greater for plug-flow reactor than for the single CSTR of the same volume (B) Statement in (A) is wrong (C) Decreases with increasing conversion (D) Both (A) and (C) hold good

Last Answer : (D) Both (A) and (C) hold good

Two half-reactions of an electrochemical cell are given below : MnO–4 (aq) + 8H+ (aq) + 5e– → Mn2+ (aq) + 4H2O (I), E° = 1.51 V Sn2+ (aq) → Sn4+ (aq) + 2e–, E° = + 0.15 V. Construct the redox equation from the standard potential of the cell and predict if the reaction is reactant favoured or product favoured. -Chemistry

Description : Two half-reactions of an electrochemical cell are given below : MnO-4 (aq) + 8H+ (aq) + 5e- → Mn2+ (aq) + 4H2O (I), E° = 1.51 V Sn2+ (aq) → Sn4+ (aq) + 2e- ... the redox equation from the standard potential of the cell and predict if the reaction is reactant favoured or product favoured. -Chemistry

Last Answer : The reactions can be represented at anode and at cathode in the following ways : At anode (oxidation) : Sn2+ → = Sn4+ (aq) + 2e- ] 5 E° = + 0.15 V At cathode (reduction) : MnO-4(aq) + 8H+ ... = E°cathode - E°anode = 1.51 - 0.15 = + 1.36 V ∴ Positive value of E°cell favours formation of product.

Two half-reactions of an electrochemical cell are given below : MnO–4 (aq) + 8H+ (aq) + 5e– → Mn2+ (aq) + 4H2O (I), E° = 1.51 V Sn2+ (aq) → Sn4+ (aq) + 2e–, E° = + 0.15 V. Construct the redox reaction equation from the two half-reactions and calculate the cell potential from the standard potentials and predict if the reaction is reactant or product favoured. -Chemistry

Description : Two half-reactions of an electrochemical cell are given below : MnO-4 (aq) + 8H+ (aq) + 5e- → Mn2+ (aq) + 4H2O (I), E° = 1.51 V Sn2+ (aq) → Sn4+ (aq) + ... -reactions and calculate the cell potential from the standard potentials and predict if the reaction is reactant or product favoured. -Chemistry

Last Answer : The reactions can be represented at anode and at cathode in the following ways : At anode (oxidation) : Sn2+ → Sn4+ (aq) + 2e- ] 5 E° = + 0.15 V Af cathode (reduction) : MnO-4(aq) + 8H+ ( ... = E°cathode - E°anode = 1.51 - 0.15 = + 1.36 V ∴ Positive value of E°cell favours formation of product.

Which of the following reactant will give the same product as (III) ,(ii),(Q) with NaOI ?

Description : Which of the following reactant will give the same product as (III) ,(ii),(Q) with NaOI ?

Last Answer : Which of the following reactant will give the same product as (III) ,(ii),(Q) with NaOI ? A. B. `CH_( ... `CH_3-CH_(2)overset(O)overset(||)(C)-CH_(3)`

Which of the following reactant will give the same product as (III) ,(ii),(Q) with NaOI ?

Description : Which of the following reactant will give the same product as (III) ,(ii),(Q) with NaOI ?

Last Answer : Which of the following reactant will give the same product as (III) ,(ii),(Q) with NaOI ? A. B. `CH_( ... `CH_3-CH_(2)overset(O)overset(||)(C)-CH_(3)`

In photosynthesis is chlorophyll considered a reactant a product neither how does the role of chlorophyll compare with the roles of co2 and h20?

Description : In photosynthesis is chlorophyll considered a reactant a product neither how does the role of chlorophyll compare with the roles of co2 and h20?

Last Answer : Need answer

Is silver nitrate a reactant or product?

Description : Is silver nitrate a reactant or product?

Last Answer : product

Is iron sulphate a reactant or a product?

Description : Is iron sulphate a reactant or a product?

Last Answer : What is the answer ?

Burning of Gasoline initially requires heat before it burns spontaneously. Which of the following does not give a good explanation of this phenomenon?  a. the initial heat rises the enthalpy of the reactant  b. the initial heat lowers the activation of energy of the reactants  c. the enthalpy of reactants is lower than the enthalpy of products.  d. The enthalpy of the product is lower than the enthalpy of the reactant

Description : Burning of Gasoline initially requires heat before it burns spontaneously. Which of the following does not give a good explanation of this phenomenon?  a. the initial heat rises the enthalpy of the reactant ... of products.  d. The enthalpy of the product is lower than the enthalpy of the reactant

Last Answer : the enthalpy of reactants is lower than the enthalpy of products.

Identify the INCORRECT statement below regarding chemical equilibrium. A All chemical reactions are, in principle, reversible. B Equilibrium is achieved when the forward reaction rate equals the reverse reaction rate. C Equilibrium is achieved when the concentrations of species become constant. D Equilibrium is achieved when the reaction quotient, Q, equals the equilibrium constant. E Equilibrium is achieved when reactant and product concentrations are equal.

Description : Identify the INCORRECT statement below regarding chemical equilibrium. A All chemical reactions are, in principle, reversible. B Equilibrium is achieved when the forward reaction rate equals the ... equilibrium constant. E Equilibrium is achieved when reactant and product concentrations are equal.

Last Answer : E Equilibrium is achieved when reactant and product concentrations are equal.

In a photosynthesis reaction, chlorophyll is: w) a reactant w) a product y) a catalyst z) an intermediate

Description : In a photosynthesis reaction, chlorophyll is: w) a reactant w) a product y) a catalyst z) an intermediate

Last Answer : ANSWER: Y -- A CATALYST

In vibrometer, the relative motion between the mass and vibrating body is converted into proportional ________. (A) current (B) voltage (C) resistance (D) ampere

Description : In vibrometer, the relative motion between the mass and vibrating body is converted into proportional ________. (A) current (B) voltage (C) resistance (D) ampere

Last Answer : (B) voltage

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

This is referred to a product of simultaneous frequency and amplitude modulation or a carrier frequency variation which produces unwanted distortion. A. Absorption modulation B. Simultaneous modulation C. Dynamic instability D. Series modulation

Description : This is referred to a product of simultaneous frequency and amplitude modulation or a carrier frequency variation which produces unwanted distortion. A. Absorption modulation B. Simultaneous modulation C. Dynamic instability D. Series modulation

Last Answer : C. Dynamic instability

“Relative land area under sole crop required to produce the same yield as obtained under a mixed or intercropping system at the same level of management is termed as

Description : “Relative land area under sole crop required to produce the same yield as obtained under a mixed or intercropping system at the same level of management is termed as

Last Answer : Ans.Land equivalent ratio (LER)

What is the selectivity index, if the grade of tailings & concentrate is the same? (A) 0 (B) ∞ (C) 1 (D) 0.5

Description : What is the selectivity index, if the grade of tailings & concentrate is the same? (A) 0 (B) ∞ (C) 1 (D) 0.5

Last Answer : (C) 1

Pick out the correct statement. (A) In case of liquid-liquid extraction, no separation is possible, if the selectivity of the solvent used is unity (B) With increase in temperature, the selectivity of the solvent used in solvent extraction decreases (C) The selectivity of solvent used in solvent extraction is unity at the plait point (D) All (A), (B) and (C)

Description : Pick out the correct statement. (A) In case of liquid-liquid extraction, no separation is possible, if the selectivity of the solvent used is unity (B) With increase in temperature, the selectivity of the solvent used ... in solvent extraction is unity at the plait point (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick out the wrong statement. (A) Critical moisture content is not a property of the material itself (B) A sharp increase in pressure drop gives an indication of the flooding in a distillation column (C) Separation of components is not possible in liquid extraction, if selectivity is unity (D) Dehydration of ethyl alcohol is most economically done by molecular distillation at very high vacuum

Description : Pick out the wrong statement. (A) Critical moisture content is not a property of the material itself (B) A sharp increase in pressure drop gives an indication of the flooding in a ... unity (D) Dehydration of ethyl alcohol is most economically done by molecular distillation at very high vacuum

Last Answer : (D) Dehydration of ethyl alcohol is most economically done by molecular distillation at very high vacuum

Selectivity of the solvent used in solvent extraction should be (A) 1 (B) > 1 (C) < 1 (D) 0

Description : Selectivity of the solvent used in solvent extraction should be (A) 1 (B) > 1 (C) < 1 (D) 0

Last Answer : (B) > 1

The solvent used in liquid-liquid extraction should have __________ less than one. (A) Selectivity (B) Distribution co-efficient(C) Both (A) and (B)(D) Neither (A) nor (B)

Description : The solvent used in liquid-liquid extraction should have __________ less than one. (A) Selectivity (B) Distribution co-efficient (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (D) Neither (A) nor (B)

In which of the following unit operations, the selectivity is an important parameter? (A) Distillation (B) Solvent extraction (C) Absorption (D) None of these

Description : In which of the following unit operations, the selectivity is an important parameter? (A) Distillation (B) Solvent extraction (C) Absorption (D) None of these

Last Answer : (B) Solvent extraction

In liquid extraction, if the selectivity is unity, then (A) Separation of the constituents is the most effective (B) No separation will occur (C) Amount of solvent required will be minimum (D) Solvent flow rate should be very low

Description : In liquid extraction, if the selectivity is unity, then (A) Separation of the constituents is the most effective (B) No separation will occur (C) Amount of solvent required will be minimum (D) Solvent flow rate should be very low

Last Answer : (B) No separation will occur

Polar organic compounds are normally used as separating agents for the azeotropic and extractive distillation. Which of the following is the most important factor to be considered for the choice of the separating agent for extractive distillation? (A) Cost (B) Availability(C) Toxicity(D) Selectivity

Description : Polar organic compounds are normally used as separating agents for the azeotropic and extractive distillation. Which of the following is the most important factor to be considered for the choice of the separating agent ... ? (A) Cost (B) Availability (C) Toxicity (D) Selectivity

Last Answer : (D) Selectivity

In Orsat's apparatus, ammoniacal cuprous chloride is used for selectivity absorbing (A) CO (B) CO2 (C) O2 (D) H2O

Description : In Orsat's apparatus, ammoniacal cuprous chloride is used for selectivity absorbing (A) CO (B) CO2 (C) O2 (D) H2O

Last Answer : (A) CO