The minimum frame size required for a CSMA/CD based computer network running at 1 Gbps on a 200m cable with a link speed of 2 × 108m/s is a. 125 bytes b. 250 bytes c. 500 bytes d. None of these

The minimum frame size required for a
CSMA/CD based computer network
running at 1 Gbps on a 200m cable with a
link speed of 2 × 108m/s is
a. 125 bytes
b. 250 bytes
c. 500 bytes
d. None of these
by

1 Answer

Answer :

b. 250 bytes
by

Related questions

Consider a CSMA/CD network that transmits data at a rate of 100 Mbps (108 bits per second) over a 1 km (kilometre) cable with no repeaters. If the minimum frame size required for this network is 1250 bytes, what is the signal speed (km/sec) in the cable? a. 8000 b. 10000 c. 16000 d. 20000

Description : Consider a CSMA/CD network that transmits data at a rate of 100 Mbps (108 bits per second) over a 1 km (kilometre) cable with no repeaters. If the minimum frame size required for this network is 1250 bytes, what is the signal speed (km/sec) in the cable? a. 8000 b. 10000 c. 16000 d. 20000

Last Answer : d. 20000

Which of the following statements is TRUE about CSMA/CD a. IEEE 802.11 wireless LAN runs CSMA/CD protocol b. Ethernet is not based on CSMA/CD protocolc. CSMA/CD is not suitable for a high propagation delay network like satellite network d. There is no contention in a CSMA/CD network

Description : Which of the following statements is TRUE about CSMA/CD a. IEEE 802.11 wireless LAN runs CSMA/CD protocol b. Ethernet is not based on CSMA/CD protocol c. CSMA/CD is not suitable for a high propagation delay network like satellite network d. There is no contention in a CSMA/CD network

Last Answer : CSMA/CD is not suitable for a high propagation delay

In ________,a station monitors the medium after it sends a frame to see if the transmission was successful. If so, the station is finished. If, however, there is a collision, the frameis sentagain. A) CSMA/CA B) CSMA/CD C) either (a)or (b) D) both (a) and (b)

Description : In ________,a station monitors the medium after it sends a frame to see if the transmission was successful. If so, the station is finished. If, however, there is a collision, the frameis sentagain. A) CSMA/CA B) CSMA/CD C) either (a)or (b) D) both (a) and (b)

Last Answer : CSMA/CD

A sender uses the Stop-and-Wait ARQ protocol for reliable transmission of frames. Frames are of size 1000 bytes and the transmission rate at the sender is 80 Kbps (1Kbps = 1000 bits/second). Size of an acknowledgement is 100 bytes and the transmission rate at the receiver is 8 Kbps. The one-way propagation delay is 100 milliseconds. Assuming no frame is lost, the sender throughput is __________ bytes/second. a. 2500 b. 2000 c. 1500 d. 500

Description : A sender uses the Stop-and-Wait ARQ protocol for reliable transmission of frames. Frames are of size 1000 bytes and the transmission rate at the sender is 80 Kbps (1Kbps = 1000 bits/second). Size of ... is lost, the sender throughput is __________ bytes/second. a. 2500 b. 2000 c. 1500 d. 500

Last Answer : a. 2500

What is the recommended minimum range of illumination required by BS EN 970 for inspection of a welded surface? a) 90 to 125 lux b) 150 to 250 lux c) 350 to 500 lux d) 35 to 50 lux

Description : What is the recommended minimum range of illumination required by BS EN 970 for inspection of a welded surface? a) 90 to 125 lux b) 150 to 250 lux c) 350 to 500 lux d) 35 to 50 lux

Last Answer : c) 350 to 500 lux

How many bytes of data can be sent in 15 seconds over a serial link with baud rate of 9600 in asynchronous mode with odd parity and two stop bits in the frame? a. 10,000 bytes b. 12,000 bytes c. 15,000 bytes d. 27,000 bytes

Description : How many bytes of data can be sent in 15 seconds over a serial link with baud rate of 9600 in asynchronous mode with odd parity and two stop bits in the frame? a. 10,000 bytes b. 12,000 bytes c. 15,000 bytes d. 27,000 bytes

Last Answer : b. 12,000 bytes

Consider a link with packet loss probability of 0.2. What is the expected number of transmissions it would take to transfer 200 packets given that the stop and wait protocol is used? a. 125 b. 250 c. 225

Description : Consider a link with packet loss probability of 0.2. What is the expected number of transmissions it would take to transfer 200 packets given that the stop and wait protocol is used? a. 125 b. 250 c. 225

Last Answer : b. 250

Which of the following describes a TDM frame? A. A 250-μs frame B. A 125-μs frame C. A 500-μs frame D. A 60-μs frame

Description : Which of the following describes a TDM frame? A. A 250-μs frame B. A 125-μs frame C. A 500-μs frame D. A 60-μs frame

Last Answer : B. A 125-μs frame

The reason a CSMA/CD network has a minimum length for packets is:

Description : The reason a CSMA/CD network has a minimum length for packets is:

Last Answer : to make sure all other nodes hear a collision in progress

Determine the maximum length of the cable (in km) for transmitting data at a rate of 500 Mbps in an Ethernet LAN with frames of size 10,000 bits. Assume the signal speed in the cable to be 2,00,000 km/s.b. 2 c. 2.5 d. 5

Description : Determine the maximum length of the cable (in km) for transmitting data at a rate of 500 Mbps in an Ethernet LAN with frames of size 10,000 bits. Assume the signal speed in the cable to be 2,00,000 km/s. b. 2 c. 2.5 d. 5

Last Answer : b. 2

In IEEE 802.11, the access method used in the DCF sublayer is _________. A) ALOHA B) CSMA/CA C) CSMA/CD D) none of the above

Description : In IEEE 802.11, the access method used in the DCF sublayer is _________. A) ALOHA B) CSMA/CA C) CSMA/CD D) none of the above

Last Answer : CSMA/CA

In_______, collisions are avoidedthrough theuse of three strategies: the interframe space, the contention window,and acknowledgments. A) CSMA/CA B) CSMA/CD C) either (a)or (b) D) both (a) and (b)

Description : In_______, collisions are avoidedthrough theuse of three strategies: the interframe space, the contention window,and acknowledgments. A) CSMA/CA B) CSMA/CD C) either (a)or (b) D) both (a) and (b)

Last Answer : CSMA/CA

Toavoid collisions on wireless networks, ________was invented. A) CSMA/CA B) CSMA/CD C) either (a)or (b) D) both (a) and (b)

Description : Toavoid collisions on wireless networks, ________was invented. A) CSMA/CA B) CSMA/CD C) either (a)or (b) D) both (a) and (b)

Last Answer : CSMA/CA

__________ augments the CSMA algorithm todetect collision. A) CSMA/CA B) CSMA/CD C) either (a)or (b) D) both (a) and (b

Description : __________ augments the CSMA algorithm todetect collision. A) CSMA/CA B) CSMA/CD C) either (a)or (b) D) both (a) and (b

Last Answer : CSMA/CD

The _____sublayer is responsible for the operation of the CSMA/CD access method and framing. A) LLC B) MII C) MAC D) none of the above

Description : The _____sublayer is responsible for the operation of the CSMA/CD access method and framing. A) LLC B) MII C) MAC D) none of the above

Last Answer : MAC

The IEEE 802.3 Standard defines _________ CSMA/CD as the access method for first-generation 10-Mbps Ethernet. A) 1-persistent B) p-persistent C) non-persistent D) none of the above

Description : The IEEE 802.3 Standard defines _________ CSMA/CD as the access method for first-generation 10-Mbps Ethernet. A) 1-persistent B) p-persistent C) non-persistent D) none of the above

Last Answer : 1-persistent

In Ethernet CSMA/CD, the special bit sequence transmitted by media access management to handle collision is called a. Preamble b. Postamble c. Jam d. None of the above

Description : In Ethernet CSMA/CD, the special bit sequence transmitted by media access management to handle collision is called a. Preamble b. Postamble c. Jam d. None of the above

Last Answer : c. Jam

Which of the following is the multiple access protocol for channel access control? a. CSMA/CD b. CSMA/CA c. Both CSMA/CD & CSMA/CA d. HDLC

Description : Which of the following is the multiple access protocol for channel access control? a. CSMA/CD b. CSMA/CA c. Both CSMA/CD & CSMA/CA d. HDLC

Last Answer : c. Both CSMA/CD & CSMA/CA

In _______, collisions are avoided through the use of three strategies: the interframe space, the contention window, and acknowledgments. A. CSMA/CA B. CSMA/CD C. either (a) or (b)D. both (a) and (b)

Description : In _______, collisions are avoided through the use of three strategies: the interframe space, the contention window, and acknowledgments. A. CSMA/CA B. CSMA/CD C. either (a) or (b) D. both (a) and (b)

Last Answer : A. CSMA/CA

Which of the following is the multiple access protocol for channel access control? A. CSMA/CD B. CSMA/CA C. Both CSMA/CD & CSMA/CA D. HDLC

Description : Which of the following is the multiple access protocol for channel access control? A. CSMA/CD B. CSMA/CA C. Both CSMA/CD & CSMA/CA D. HDLC

Last Answer : C. Both CSMA/CD & CSMA/CA

Explain CSMA/CD and CSMA/CA.

Description : Explain CSMA/CD and CSMA/CA.

Last Answer : CSMA- resolving the media contention. Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Listen for Data Transmission on Cable (Carrier Sense) When Medium is free a) Transmit ... time, and transmit again. Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA) Nov/Dec

What is CSMA/CD?

Description : What is CSMA/CD?

Last Answer : Carrier Sense Multiple Access with Collision Detection (CSMA/CD) When a station has a frame to transmit: 1) Listen for Data Transmission on Cable (Carrier Sense) 2) When Medium is Quiet (no ... for Collision. b) If collision is heard, stop transmitting, wait random time, and transmit again.

An IP datagram of size 1000 bytes arrives at a router. The router has to forward this packet on a link whose MTU (maximum transmission unit) is 100 bytes. Assume that the size of the IP header is 20 bytes. The number of fragments that the IP datagram will be divided into for transmission is : a. 10 b. 50 c. 12 d. 13

Description : An IP datagram of size 1000 bytes arrives at a router. The router has to forward this packet on a link whose MTU (maximum transmission unit) is 100 bytes. Assume that the size of the IP header is 20 bytes ... the IP datagram will be divided into for transmission is : a. 10 b. 50 c. 12 d. 13

Last Answer : d. 13

In an Ethernet local area network, which one of the following statements is TRUE ? a. A station stops to sense the channel once it starts transmitting a frame. b. The purpose of the jamming signal is to pad the frames that are smaller than the minimum frame size. c. A station continues to transmit the packet even after the collision is detected. d. The exponential backoff mechanism reduces the probability of collision on retransmissions

Description : In an Ethernet local area network, which one of the following statements is TRUE ? a. A station stops to sense the channel once it starts transmitting a frame. b. The purpose ... collision is detected. d. The exponential backoff mechanism reduces the probability of collision on retransmissions

Last Answer : The exponential backoff mechanism reduces the probability of collision on retransmissions

In a token ring network the transmission speed is 10^7 bps and the propagation speed is 200 metres/micro second. The 1- bit delay in this network is equivalent to: a. 500 metres of cable. b. 200 metres of cable. c. 20 metres of cable. d. 50 metres of cable

Description : In a token ring network the transmission speed is 10^7 bps and the propagation speed is 200 metres/micro second. The 1- bit delay in this network is equivalent to: a. 500 metres of cable. b. 200 metres of cable. c. 20 metres of cable. d. 50 metres of cable

Last Answer : c. 20 metres of cable.

What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Description : What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Last Answer : C. 125,000

What is he required surface finish for raised or flat faced gasket surfaces? a) 63 µ in. b) 125 µ in-250 µ in. c) 250 µ in-400 µ in. d) 400-500 µ in.

Description : What is he required surface finish for raised or flat faced gasket surfaces? a) 63 µ in. b) 125 µ in-250 µ in. c) 250 µ in-400 µ in. d) 400-500 µ in.

Last Answer : b) 125 µ in-250 µ in.

Which of the following arevalid Minimum and Maximum zoom sizes in MSOffice? A. 10, 100 B. 20,250 C. 10, 500 D. 10,1000

Description : Which of the following arevalid Minimum and Maximum zoom sizes in MSOffice? A. 10, 100 B. 20,250 C. 10, 500 D. 10,1000

Last Answer : 10, 500

Which protocols adopted the standards of HDLC (High Level Link Control) protocol? a. X.25 protocol as LAPB (Link Access Procedure Balanced, V.42 protocol as LAPM (Link Access Procedure for Modems) b. Frame Relay protocol as LAPF (Link Access Procedure for Frame Relay) c. ISDN (Integrated Services Digital Network) protocol as LAPD (Link Access Procedure on D channel) d. All the above

Description : Which protocols adopted the standards of HDLC (High Level Link Control) protocol? a. X.25 protocol as LAPB (Link Access Procedure Balanced, V.42 protocol as LAPM (Link Access Procedure for ... Services Digital Network) protocol as LAPD (Link Access Procedure on D channel) d. All the above

Last Answer : d. All the above

The maximum frame length for 10-Mbps Ethernet is ________ bytes. A) 1518 B) 1500 C) 1200 D) none of the abov

Description : The maximum frame length for 10-Mbps Ethernet is ________ bytes. A) 1518 B) 1500 C) 1200 D) none of the abov

Last Answer : 1518

In SONET, for each frame, the bytes are transmitted __________. A) from left to the right, top to bottom B) from right to theleft, bottom to top C) from left to the right, bottom to top D) from right to the left, top to bottom

Description : In SONET, for each frame, the bytes are transmitted __________. A) from left to the right, top to bottom B) from right to theleft, bottom to top C) from left to the right, bottom to top D) from right to the left, top to bottom

Last Answer : from left to the right, bottom to top

In Frame Relay, the EA field defines thenumber of bytes; it is _____ in the last byte of the address. A) 0 B) 1 C) 2 D) 3

Description : In Frame Relay, the EA field defines thenumber of bytes; it is _____ in the last byte of the address. A) 0 B) 1 C) 2 D) 3

Last Answer : 1

In Frame Relay, an address can be________ bytes. A) only 2 B) 2 to 3 C) 2 to 4 D) none of the above

Description : In Frame Relay, an address can be________ bytes. A) only 2 B) 2 to 3 C) 2 to 4 D) none of the above

Last Answer : 2 to 4

Header of a frame generally contains a. synchronization bytes b. addresses c. frame identifier d. all of the mentioned

Description : Header of a frame generally contains a. synchronization bytes b. addresses c. frame identifier d. all of the mentioned

Last Answer : d. all of the mentioned

Header of a Layer two frame usually contain ______________ A. synchronization bytes B. addresses C. frame identifier D. all of the mentioned

Description : Header of a Layer two frame usually contain ______________ A. synchronization bytes B. addresses C. frame identifier D. all of the mentioned

Last Answer : D. all of the mentioned

What is the average uploading speed of 4G LTE network? a) 1-3 Gbps b) 2-5 Gbps c) 1-3 Mbps d) 2-5 Mbps

Description : What is the average uploading speed of 4G LTE network? a) 1-3 Gbps b) 2-5 Gbps c) 1-3 Mbps d) 2-5 Mbps

Last Answer : d) 2-5 Mbps

Transmission system for a multidrop network A. Taken passing B. Polling C. Switching D. CSMA/CD

Description : Transmission system for a multidrop network A. Taken passing B. Polling C. Switching D. CSMA/CD

Last Answer : B. Polling

A hare is spotted by a tiger from a distance of 50 metres. When the tiger starts a chase, the hare also starts running. If the speed of the hare be 4 km/hr and that of a tiger 5 km/hr, how far the hare will have run before its over taken? a) 100m b) 200m c) 300m d) 400m

Description : A hare is spotted by a tiger from a distance of 50 metres. When the tiger starts a chase, the hare also starts running. If the speed of the hare be 4 km/hr and that of a tiger 5 km/hr, how far the hare will have run before its over taken? a) 100m b) 200m c) 300m d) 400m

Last Answer : B Relative speed of the tiger = (5-4)km/hr =1 km/hr Time taken by tiger to cover 50 m, =(50/1000)hr =1/20hr In 1/20 hrs, the tiger cover a distance of (4*1/20)km =1/5km =>(1/5*1000)m =200m

Find the time taken by mailtrain 200m long running at a speed of 120 km/hr to cross another train of length 160m running at a speed of 96km/hr in the same direction. A) 34sec B) 52sec C) 45sec D) 54sec

Description : Find the time taken by mailtrain 200m long running at a speed of 120 km/hr to cross another train of length 160m running at a speed of 96km/hr in the same direction. A) 34sec B) 52sec C) 45sec D) 54sec

Last Answer : ANSWER: D  Explanation:  Total distance covered to cross each other = 200 + 160  = 360m  If the direction is given in the same direction then we subtract  Relative speed of two trains (same direction) = ... * 3 / 20  = 54sec  Time taken by the faster train to cross the slower train is 54sec.

Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is __________. a. 400 bps b. 800 bps c. 1600 bps d. 3200 bps

Description : Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is __________. a. 400 bps b. 800 bps c. 1600 bps d. 3200 bps

Last Answer : d. 3200 bps

What is the range of asynchronous user data rates provided by HIPER-LAN? a) 1-100 Mbps b) 50-100 Mbps c) 1-20 Mbps d) 500 Mbps to 1 Gbps

Description : What is the range of asynchronous user data rates provided by HIPER-LAN? a) 1-100 Mbps b) 50-100 Mbps c) 1-20 Mbps d) 500 Mbps to 1 Gbps

Last Answer : c) 1-20 Mbps

A woman’s neglected hangnail has developed into a mild staphylococcal cellulites. Which of the following regimens would be appropriate oral therapy? (a) Dicloxacillin 125 mg q6h (b) Vancomycin 250 mg q6h (c) Methicillin 500 mg q6h (d) Cefazolin 1 g q8h (e) Penicillin V 500 mg q6h

Description : A woman’s neglected hangnail has developed into a mild staphylococcal cellulites. Which of the following regimens would be appropriate oral therapy? (a) Dicloxacillin 125 mg q6h (b) Vancomycin 250 mg q6h (c) Methicillin 500 mg q6h (d) Cefazolin 1 g q8h (e) Penicillin V 500 mg q6h

Last Answer : Ans: A

Suppose that the one-way propagation delay for a 100 Mbps Ethernet having 48-bit jamming signal is 1.04 micro-seconds. The minimum frame size in bits is: a. 112 b. 160 c. 208 d. 256

Description : Suppose that the one-way propagation delay for a 100 Mbps Ethernet having 48-bit jamming signal is 1.04 micro-seconds. The minimum frame size in bits is: a. 112 b. 160 c. 208 d. 256

Last Answer : d. 256

Suppose the round trip propagation delay for a 10 Mbps Ethernet having 48-bit jamming signal is 46.4 ms. The minimum frame size is a. 94 b. 416 c. 464

Description : Suppose the round trip propagation delay for a 10 Mbps Ethernet having 48-bit jamming signal is 46.4 ms. The minimum frame size is a. 94 b. 416 c. 464

Last Answer : c. 464

Which of the following technique isused for encapsulation? A. a technique used inbest-effort delivery systems toavoid endlessly loopingpackets. B. a technique used by protocols in which a lower level protocol accepts a message from ahigher level protocol and places it in the data portion of the low level frame. C. One of the pieces that results when an IP gateway divides an IP datagram into smallerpieces for transmission acrossa network that cannothandle the originaldatagram size D. All of theabove E. None of the above

Description : Which of the following technique isused for encapsulation? A. a technique used inbest-effort delivery systems toavoid endlessly loopingpackets. B. a technique used by protocols in which a lower level ... network that cannothandle the originaldatagram size D. All of theabove E. None of the above

Last Answer : a technique used by protocols in which a lower level protocol accepts a message from ahigher level protocol and places it in the data portion of the low level frame

Which of the following technique isused for fragment? A. a technique used inbest-effort delivery systems toavoid endlessly loopingpackets B. a technique used by protocols in which a lower level protocol accepts a message from ahigher level protocol and places it in the data portion of the low level frame C. one of the pieces that results when an IP gateway divides an IP datagram into smallerpieces for transmission acrossa network that cannothandle the originaldatagram size D. All of theabove E. None of the above

Description : Which of the following technique isused for fragment? A. a technique used inbest-effort delivery systems toavoid endlessly loopingpackets B. a technique used by protocols in which a lower level protocol ... network that cannothandle the originaldatagram size D. All of theabove E. None of the above

Last Answer : one of the pieces that results when an IP gateway divides an IP datagram into smallerpieces for transmission acrossa network that cannothandle the originaldatagram size

Flat rate parcel rates Flat Rate Parcel Boxes size Dimension of boxes (in mm) Weight (in Kg.) Tariff (in Rs.) Small - S 250*50*300 0 to 1 125 Medium - M 250*100*300 Above 1 to 2.5 200 Large - L 300*250*200 Above 2.5 to 5 400

Description : Flat rate parcel rates Flat Rate Parcel Boxes size Dimension of boxes (in mm) Weight (in Kg.) Tariff (in Rs.) Small - S 250*50*300 0 to 1 125 Medium - M 250*100*300 Above 1 to 2.5 200 Large - L 300*250*200 Above 2.5 to 5 400

Last Answer : Large - L 300*250*200 Above 2.5 to 5 400

The network layer is concerned with __________ of data. a. bits b. frames c. packets d. bytes

Description : The network layer is concerned with __________ of data. a. bits b. frames c. packets d. bytes

Last Answer : c. packets