__________ pumps are axial flow pumps. (A) Turbine (B) Propeller (C) Diffuser (D) None of these

__________ pumps are axial flow pumps.
(A) Turbine
(B) Propeller
(C) Diffuser
(D) None of these
by

1 Answer

Answer :

(B) Propeller
by

Related questions

__________ is an example of axial flow impeller. (A) Paddle (B) Turbine (C) Propeller (D) All (A), (B) and (C)

Description : __________ is an example of axial flow impeller. (A) Paddle (B) Turbine (C) Propeller (D) All (A), (B) and (C)

Last Answer : (C) Propeller

A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Description : A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Last Answer : (A) Produces mainly axial flow

A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow

The propeller shaft speed in a turbo-electric, synchronous, propulsion drive motor is changed by varying the __________. A. turbine speed B. number of motor poles C. field strength of the generator D. field strength of the motor

Description : The propeller shaft speed in a turbo-electric, synchronous, propulsion drive motor is changed by varying the __________. A. turbine speed B. number of motor poles C. field strength of the generator D. field strength of the motor

Last Answer : Answer: A

Propeller type centrifugal pumps are most suitable for (A) High capacity at high heads (B) High capacity at low heads (C) Low capacity at high heads (D) Low capacity at low heads

Description : Propeller type centrifugal pumps are most suitable for (A) High capacity at high heads (B) High capacity at low heads (C) Low capacity at high heads (D) Low capacity at low heads

Last Answer : (B) High capacity at low heads

Most commonly used pump for lifting water in water supply mains, is (A) Axial flow pump (B) Reciprocating pump (C) Rotary type pump (D) Centrifugal pumps

Description : Most commonly used pump for lifting water in water supply mains, is  (A) Axial flow pump  (B) Reciprocating pump  (C) Rotary type pump  (D) Centrifugal pumps 

Last Answer : (A) Axial flow pump 

Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow (C) Generally, the diameter of the agitator is kept between l/3rd to l/6th of the tank diameter while the blade length is l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Description : Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with ... l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Last Answer : (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow

Most of the centrifugal pumps used in chemical plants are usually __________ driven. (A) Steam (B) Diesel engine (C) Electric motor (D) Gas turbine

Description : Most of the centrifugal pumps used in chemical plants are usually __________ driven. (A) Steam (B) Diesel engine (C) Electric motor (D) Gas turbine

Last Answer : (C) Electric motor

Pick up the correct statement from the following regarding radial flow centrifugal pumps: (A) These are provided with volute type or turbine type casings (B) In involute type of radial flow centrifugal pump, the impeller discharges into a gradually expanding spiral casing (C) The efficiency of turbine type of radial flow centrifugal pump, is always higher than that of volute type (D) All the above

Description : Pick up the correct statement from the following regarding radial flow centrifugal pumps:  (A) These are provided with volute type or turbine type casings  (B) In involute type of radial flow ... centrifugal pump, is always higher than that of  volute type  (D) All the above 

Last Answer : (D) All the above 

Which of the following is the most suitable for handling fibrous and dense slurries? (A) Propeller agitator (B) Cone type agitator (C) Turbine agitator

Description : Which of the following is the most suitable for handling fibrous and dense slurries? (A) Propeller agitator (B) Cone type agitator (C) Turbine agitator

Last Answer : (B) Cone type agitator

Which of the following agitators having a large blade area, rotating at slow speed is used for mixing high viscosity liquids (> 50000 centipoise)? (A) Propeller(B) Helical screw(C) Flat blade turbine(D) Curved blade turbine

Description : Which of the following agitators having a large blade area, rotating at slow speed is used for mixing high viscosity liquids (> 50000 centipoise)? (A) Propeller (B) Helical screw (C) Flat blade turbine (D) Curved blade turbine

Last Answer : (B) Helical screw

Draining of shallow pits or sump is done by a sump pump, which is a __________ pump. (A) Single stage vertical (B) Centrifugal (C) Plunger (D) Diffuser

Description : Draining of shallow pits or sump is done by a sump pump, which is a __________ pump. (A) Single stage vertical (B) Centrifugal (C) Plunger (D) Diffuser

Last Answer : (A) Single stage vertical

. A special type of liquid transporting device is the diffuser pump, in which __________ are minimised. (A) Bearing losses (B) Disk friction (C) Shock losses (D) Cavitation

Description : . A special type of liquid transporting device is the diffuser pump, in which __________ are minimised. (A) Bearing losses (B) Disk friction (C) Shock losses (D) Cavitation

Last Answer : (C) Shock losses

A turbine is said to have an axial discharge when the steam leaves the blade tip at _________ to the direction of the blade motion. (A) 60° (B) 90° (C) 180° (D) 270°

Description : A turbine is said to have an axial discharge when the steam leaves the blade tip at _________ to the direction of the blade motion. (A) 60° (B) 90° (C) 180° (D) 270°

Last Answer : (B) 90°

High specific speed of a pump implies that, it is a/an __________ pump. (A) Centrifugal (B) Mixed flow (C) Axial flow (D) None of these

Description : High specific speed of a pump implies that, it is a/an __________ pump. (A) Centrifugal (B) Mixed flow (C) Axial flow (D) None of these

Last Answer : (C) Axial flow

Higher specific speed (200-500) of a centrifugal pump indicates that the pump is of __________ flow type. (A) Axial (B) Radial (C) Mixed (D) None of these

Description : Higher specific speed (200-500) of a centrifugal pump indicates that the pump is of __________ flow type. (A) Axial (B) Radial (C) Mixed (D) None of these

Last Answer : (A) Axial

Low specific speed of a pump implies that, it is a/an __________ pump. (A) Axial flow (B) Centrifugal (C) Mixed flow (D) None of these

Description : Low specific speed of a pump implies that, it is a/an __________ pump. (A) Axial flow (B) Centrifugal (C) Mixed flow (D) None of these

Last Answer : (B) Centrifugal

Working of a __________ pump characterises mixed flow. (A) Turbine (B) Piston (C) Diaphragm (D) None of these

Description : Working of a __________ pump characterises mixed flow. (A) Turbine (B) Piston (C) Diaphragm (D) None of these

Last Answer : (A) Turbine

In case of a __________ the energy of flow is considerably decreased downstream of the machine. (A) Blower (B) Turbine (C) Centrifugal pump (D) Centrifugal fan

Description : In case of a __________ the energy of flow is considerably decreased downstream of the machine. (A) Blower (B) Turbine (C) Centrifugal pump (D) Centrifugal fan

Last Answer : (B) Turbine

Is it safe to use spit balls (jelly balls) in my water pipe as a diffuser?

Description : Is it safe to use spit balls (jelly balls) in my water pipe as a diffuser?

Last Answer : It sounds like sodium polyacrylate from the description. Put that name into YouTube and you'll find lots of entertaining videos showing its uses. It's also the stuff inside those packets that say NOT ... to put in your bong, but since it's used around foodstuffs, it's probably reasonably stable.

Is there a homemade recipe for the stuff that you put in a reed diffuser?

Description : Is there a homemade recipe for the stuff that you put in a reed diffuser?

Last Answer : I’d love some recipies too… I have tried using aromotherapy oils mixed with a bit of water, this worked well, but didn’t last too long

Help with finding an oil diffuser?

Description : Help with finding an oil diffuser?

Last Answer : Do you want the kind that uses a candle?

What can I use in place of a hair diffuser?

Description : What can I use in place of a hair diffuser?

Last Answer : Using certain styling products can help give you “better” curls (more definition and hold).

Is a diffuser included with the Vidal Sassoon VS783N3 Hair Dryer?

Description : Is a diffuser included with the Vidal Sassoon VS783N3 Hair Dryer?

Last Answer : The Vidal Sassoon hair dryer doesn't come with a diffuser, but it can be bought seperately.

What is the purpose of the diffuser attachment that came with my hair dryer?

Description : What is the purpose of the diffuser attachment that came with my hair dryer?

Last Answer : A diffuser on the hair dryer is used typically for curly hair, allowing it to dry and not frizz or pull out the curls. It can also be used to add volume and body.

In centrifugal compressor terminology, vaneless space refers to the space between A. The inlet and blade inlet edge B. Blades in the impeller C. Diffuser exit and volute casing D. Impeller tip and diffuser inlet edge

Description : In centrifugal compressor terminology, vaneless space refers to the space between A. The inlet and blade inlet edge B. Blades in the impeller C. Diffuser exit and volute casing D. Impeller tip and diffuser inlet edge

Last Answer : ANSWER : D

Which one of the following statements is correct? A. Reciprocating compressors are used to supply large quantities of air at a lower pressure ratio B. Centrifugal compressors are used to supply large quantities of air at a lower pressure ratio C. Centrifugal compressors are used to supply small quantities of air at a lower pressure ratio D. Centrifugal compressors cannot be run at high speed because of impeller, diffuser and casing.

Description : Which one of the following statements is correct? A. Reciprocating compressors are used to supply large quantities of air at a lower pressure ratio B. Centrifugal compressors are used to supply ... . Centrifugal compressors cannot be run at high speed because of impeller, diffuser and casing.

Last Answer : ANSWER : B

A waste heat recovery unit (WHRU) is an_________ that transfers heat from process outputs at high temperature to another part of the process for some purpose, usually increased efficiency. a) Energy recovery heat exchanger b) Energy recovery heat diffuser c) Both ‘a’ and ‘b’ d) None of the above

Description : A waste heat recovery unit (WHRU) is an_________ that transfers heat from process outputs at high temperature to another part of the process for some purpose, usually increased efficiency. a) Energy recovery heat exchanger b) Energy recovery heat diffuser c) Both ‘a’ and ‘b’ d) None of the above

Last Answer : Energy recovery heat exchanger

Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Description : Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Last Answer : (A) Is suitable for mixing low viscosity liquids

The Stoke's stream function applies to the (A) Irrotational flow only (B) Ideal/non i viscous fluids only (C) Cases of axial symmetry (D) None of these

Description : The Stoke's stream function applies to the (A) Irrotational flow only (B) Ideal/non i viscous fluids only (C) Cases of axial symmetry (D) None of these

Last Answer : (C) Cases of axial symmetry

While starting an axial flow pump, its delivery valve should be kept (A) Open (B) Closed (C) Either open or closed (D) None of these

Description : While starting an axial flow pump, its delivery valve should be kept (A) Open (B) Closed (C) Either open or closed (D) None of these

Last Answer : (A) Open

Propellers are (A) Axial flow mixers (B) Low speed impeller (C) Used for mixing liquids of high viscosity (D) Radial flow mixers

Description : Propellers are (A) Axial flow mixers (B) Low speed impeller (C) Used for mixing liquids of high viscosity (D) Radial flow mixers

Last Answer : (A) Axial flow mixers

Which of the following is most prone to pulsating discharge flow? (A) Centrifugal pump(B) Reciprocating pump(C) Gear pump(D) Axial flow pump

Description : Which of the following is most prone to pulsating discharge flow? (A) Centrifugal pump (B) Reciprocating pump (C) Gear pump (D) Axial flow pump

Last Answer : (C) Gear pump

Which of the following can be used to create a flow of gas, where no significant compression is required? (A) Reciprocating compressor (B) Blower (C) Axial flow compressor (D) Centrifugal compressor

Description : Which of the following can be used to create a flow of gas, where no significant compression is required? (A) Reciprocating compressor (B) Blower (C) Axial flow compressor (D) Centrifugal compressor

Last Answer : (B) Blower

A backmix reactor (A) Is same as plug-flow reactor (B) Is same as ideal stirred tank reactor (C) Employs mixing in axial direction only (D) Is most suitable for gas phase reaction

Description : A backmix reactor (A) Is same as plug-flow reactor (B) Is same as ideal stirred tank reactor (C) Employs mixing in axial direction only (D) Is most suitable for gas phase reaction

Last Answer : (B) Is same as ideal stirred tank reactor

In a semi-batch reactor, (A) Mixing takes place in axial direction only (B) Velocity of reaction can be controlled (C) Condition similar to plug flow reactor exists (D) Residence time is constant

Description : In a semi-batch reactor, (A) Mixing takes place in axial direction only (B) Velocity of reaction can be controlled (C) Condition similar to plug flow reactor exists (D) Residence time is constant

Last Answer : (B) Velocity of reaction can be controlled

A plug-flow reactor is characterised by (A) High capacity (B) Presence of axial mixing (C) Presence of lateral mixing (D) Constant composition and temperature of reaction mixture

Description : A plug-flow reactor is characterised by (A) High capacity (B) Presence of axial mixing (C) Presence of lateral mixing (D) Constant composition and temperature of reaction mixture

Last Answer : (C) Presence of lateral mixing

Rotary vacuum pumps can reduce the absolute pressure to as low as __________ mm Hg. (A) 1 (B) 0.1 (C) 0.01 (D) 0.001

Description : Rotary vacuum pumps can reduce the absolute pressure to as low as __________ mm Hg. (A) 1 (B) 0.1 (C) 0.01 (D) 0.001

Last Answer : (C) 0.01

Foot valves provided in pumps are __________ valves. (A) Relief (B) Three/four way (C) Pressure reducing (D) Directional contro

Description : Foot valves provided in pumps are __________ valves. (A) Relief (B) Three/four way (C) Pressure reducing (D) Directional contro

Last Answer : (D) Directional control

__________ pumps are a group of vacuum pumps. (A) Hyster (B) Sump (C) Mono (D) Submerged

Description : __________ pumps are a group of vacuum pumps. (A) Hyster (B) Sump (C) Mono (D) Submerged

Last Answer : (A) Hyster

Reciprocating pumps (A) Are not suitable for variable heads (B) Are four times costlier than centrifugal pumps (C) Are not suitable for pumping water containing sediments (D) Single stroke produce pulsating flow

Description : Reciprocating pumps  (A) Are not suitable for variable heads  (B) Are four times costlier than centrifugal pumps  (C) Are not suitable for pumping water containing sediments  (D) Single stroke produce pulsating flow 

Last Answer : (A) Are not suitable for variable heads 

Conversion of dynamic velocity head into static pressure head in a centrifugal pump is the result of : (a) Increasing area of flow between adjacent vanes from inlet to outlet (b) Difference in pressure between suction and delivery ends (c) Radial thrust in pumps (d) Stuffing Box

Description : Conversion of dynamic velocity head into static pressure head in a centrifugal pump is the result of : (a) Increasing area of flow between adjacent vanes from inlet to outlet (b) Difference in pressure between suction and delivery ends (c) Radial thrust in pumps (d) Stuffing Box

Last Answer : (b) Difference in pressure between suction and delivery ends

The most suitable equipment used to devulcanise rubber scrap and to make water dispersion & rubber solution is a (A) Boundary mixer (B) Propeller agitator (C) Sharpies centrifuge

Description : The most suitable equipment used to devulcanise rubber scrap and to make water dispersion & rubber solution is a (A) Boundary mixer (B) Propeller agitator (C) Sharpies centrifuge

Last Answer : (A) Boundary mixer

Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation (B) Cavitation may be caused due to boiling of liquid by decreasing the pressure resulting in formation & collapse of vapor cavities (C) Cavitation begins at higher static pressure and lower velocity in larger diameter pipelines resulting in audible noise(D) Large scale cavitation cannot damage pipeline, restrict fluid flow anddamage steam turbine blades

Description : Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation ... (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Last Answer : (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

In a mixer, the quantity, (v. L/D) is termed as __________ number (where, v = longitudinal velocity of material, L = length of the mixer, D = diffusivity in axial mixing). (A) Weber (B) Peclet (C) Brinkman (D) Schmidt

Description : In a mixer, the quantity, (v. L/D) is termed as __________ number (where, v = longitudinal velocity of material, L = length of the mixer, D = diffusivity in axial mixing). (A) Weber (B) Peclet (C) Brinkman (D) Schmidt

Last Answer : (B) Peclet

For very low pressure and high discharge rate, the compressor used is a/an __________ compressor. (A) Axial (B) Reciprocating (C) Rotary (D) None of these

Description : For very low pressure and high discharge rate, the compressor used is a/an __________ compressor. (A) Axial (B) Reciprocating (C) Rotary (D) None of these

Last Answer : (C) Rotary

Which one of the following types of compressor is mostly used for supercharging of IC engines? (a) Radial flow compressor (b) Axial flow compressor (c) Root blower (d) Reciprocating compressor

Description : Which one of the following types of compressor is mostly used for supercharging of IC engines? (a) Radial flow compressor (b) Axial flow compressor (c) Root blower (d) Reciprocating compressor

Last Answer : Ans : c

Compressor mostly used for supercharging of IC engine is A. Radial flow compressor B. Axial flow compressor C. Root blower compressor D. Reciprocating compressor

Description : Compressor mostly used for supercharging of IC engine is A. Radial flow compressor B. Axial flow compressor C. Root blower compressor D. Reciprocating compressor

Last Answer : ANSWER : A

Which one of the following type of compressor is mostly used for supercharging of I.C engine A. Radial flow compressor B. Axial flow compressor C. Root blower D. Reciprocating compressor.

Description : Which one of the following type of compressor is mostly used for supercharging of I.C engine A. Radial flow compressor B. Axial flow compressor C. Root blower D. Reciprocating compressor.

Last Answer : ANSWER : C

Why axial flow compressor is preferred for gas turbines for aeroplanes ?

Description : Why axial flow compressor is preferred for gas turbines for aeroplanes ?

Last Answer : Because it has low frontal area.