Description : In pre-chamber and swirl type of combustion system ______________ is used. a) single hole injector b) multi hole injector c) long stem injector d) pintle nozzle
Last Answer : Answer: d Explanation: In pre-chamber and swirl type of combustion system pintle nozzle is used and not the other nozzles.
Description : _______________ is used to enable cold starting, with out the use of a heater plug. a) Pintaux nozzle b) Multi hole injector c) Long stem injector d) Pintle nozzle
Last Answer : Answer: a Explanation: Generally, intaux nozzle is used to enable cold starting, with out the use of a heater plug.
Description : The air-fuel ratio of the petrol engine is governed by A. fuel pump B. governor C. carburetor D. injector
Last Answer : ANSWER : C
Description : Which of the following is not related to spark ignition engine? a. fuel injector b. spark plug c. flywheel d. distributor
Last Answer : ANSWER a. fuel injector
Description : Morse test is conducted on the engine to calculate the mechanical efficiency of A. single cylinder CI engine B. single cylinder SI engine C. only on two stroke engines D. multi cylinder engine
Last Answer : ANSWER : D
Description : When the head pumped against is less than the head of the fluid used for pumping, the usual device is a/an (A) Ejector (B) Blower (C) Injector (D) Airlift
Last Answer : (D) Airlift
Description : In milk chilling plant, the usual secondary refrigerant is (a)ammonia (b)sodium silicate (c) glycol (d) brine
Last Answer : Ans: d
Description : Which of the following is normally not found in both the S.I. (petrol) & C.I. (diesel) engines? (A) Air filter (B) Fuel injector (C) Exhaust silencer (D) Battery
Last Answer : Option B
Description : Ignition timing of a multi-cylinder SI engine can be adjusted by A. rotating the cam shaft B. adjusting the generator pulley C. rotating the distributor D. adjusting the pump pulley
Description : In _____________ injection system only one pump is sufficient for multi-cylinder engine. a) air b) mechanical c) compression fuel d) common rail
Last Answer : Answer: d Explanation: None.
Description : The method of determination of indicated power of multi cylinder SI engine is by use of (a) Morse test (b) Prony brake test (c) Motoring test (d) Heat balance test
Last Answer : Ans : a
Description : In multi stage compressor, the isothermal compression is achieved by A. Employing intercooler B. By constantly cooling the cylinder C. By running compressor at very slow speed D. By insulating the cylinder
Description : In a naturally aspirated diesel engine, the air is supplied by a A. supercharger B. centrifugal pump C. movement of engine piston D. reciprocating pump
Description : The knock in diesel engine occurs due to A. instantaneous and rapid burning of the first part of the charge B. instantaneous auto ignition of the last part of the charge C. delayed burning of the last part of the charge D. reduction of delay period
Last Answer : ANSWER : A
Description : A 5 BHP engine running at full load would consume diesel of the order of A. 0.3 kg/hr B. 1 kg/hr C. 3 kg/hr D. 5 kg/hr
Last Answer : ANSWER ; B
Description : Which of the following is the lightest and most volatile liquid fuel A. diesel B. kerosene C. fuel oil D. gasoline
Description : Supercharging is essential in A. aircraft engines B. petrol engines C. gas turbines D. diesel engines
Description : Most high speed compression ignition engine operate on A. dual cycle B. otto cycle C. diesel cycle D.Carnot cycle
Description : A diesel engine compared to petrol engine, running at full load is A. less efficient B. equally efficient C. more efficient D. other factors will decide it
Description : The specific fuel consumption of a petrol engine compared to diesel engine of same H.P is A. same B.more C. less D. unpredictable
Last Answer : ANSWER : B
Description : In diesel engine the fuel injected would burn instantaneously at about compressed air temperature of A. 1000°C B. 250°C C. 450°C D. 2000°C
Description : Which of the following is compressed in a diesel engine cylinder A. air B. fuel C. air and fuel D. air and lub oil
Description : The output of a diesel engine can be increased without increasing the engine speed or size in the following way A. feeding more fuel B. increasing the flywheel size C. heating intake air D. supercharging
Description : If one cylinder of a diesel engine receives more fuel than others , then for that cylinder the A. exhaust will be smoky B. scavenging occurs C. exhaust temperature will be high D. engine starts overheating
Description : The specific fuel consumption for diesel engine is approximately A. 0.15 kg/kWh B. 0.2 kg/kWh C. 28 kg/kWh D. 0.36 kg/kWh
Description : In a typical medium speed 4- stroke Diesel engine, the inlet valve A. opens 20°before top dead centre and closes at 35°afterthebottomdead centre. B. opens up at top dead centre and closes at bottomdead centre C. may open orcloseanywhere D. remains open for 200°
Description : With EFI of diesel engines a) sharp start and stop is not possible b) very high injection pressure can be obtained c) sudden cylinder cut-off is impossible d) diagnostic properties are poor
Last Answer : Answer: b Explanation: Generally, with EFI of diesel engines very high injection pressure can be obtained.
Description : A fuel of cetane number 40 has the same ignition quality as a mixture of a) 40% cetane and 60% alpha methyl naphthalene b) 40% alpha methyl naphthalene and 60% cetane c) 40% petrol and 60% diesel d) 40% diesel and 60% petrol
Last Answer : Answer: a Explanation: A fuel of cetane number 40 has the same ignition quality as a mixture of 40% cetane and 60% alpha methyl naphthalene as cetane number is counted on cetane percentage.
Description : A fuel of an octane number rating of 75 matches in knocking intensity as a mixture of a) 75% iso-octane and 25% normal heptane b) 75% normal heptane and 25% iso-octane c) 75% petrol and 25% diesel d) 75% diesel and 25% petrol
Last Answer : Answer: a Explanation: None.
Description : A 4S diesel engine, when running at 2000 rpm has an injection duration of 1.5 ms.What is the corresponding of the crank angle in degrees? (a) 18° (b) 9° (c)36° (d) 15°
Last Answer : Ans :a
Description : If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency
Last Answer : Ans :c
Description : In a 4 S diesel engine, the term ‘squish’ refers to the (a) Injection of fuel in the precombustion chamber (b) Discharge of gases from the precombustion chamber (c) Entry of air into the combustion chamber (d) Stripping of fuel from the core
Description : Keeping other parameters constant brake power of diesel engine can be increased by (a) Decreasing the density of intake air (b) Increasing the temperature of intake air (c) Increasing the pressure of intake air (d) Decreasing the pressure of intake air
Last Answer : Ans : c
Description : The fuel in diesel engine is normally injected at pressure of a. 5-10 kg/cm2 b. 20-25 kg/cm2 c 60-80 kg/cm2 d. 90-130 kg/cm2
Last Answer : ANSWER d. 90-130 kg/cm2
Description : The probability of knocking in diesel engines is increased by a. High self-ignition temperature. b. Low volatility. c. High viscosity. d. all of the above
Last Answer : ANSWER d. all of the above
Description : Diesel as compared to petrol is a. more difficult to ignite b. less difficult to ignite c. highly ignitable d. just about the same difficult to ignite
Last Answer : ANSWER a. more difficult to ignite
Description : In diesel engine, the compression ratio as compared with the expansion ratio is a. same b. less c. more d. variable
Last Answer : ANSWER c. more
Description : If diesel is used in a petrol engine a. engine will not run b. engine detonates c. engine gives smoke d. engine knocks
Last Answer : ANSWER a. engine will not run
Description : The thermal efficiency of a diesel engine is of the order of a. 92% b. 68% c. 34% d. 25%
Last Answer : ANSWER c. 34%
Description : For low load operation more economical engine is a. petrol engine b. diesel engine c. muticylinder engine d. two stroke engine
Last Answer : ANSWER b. diesel engine
Description : If petrol is used in a diesel engine a. higher knocking will occur b. efficiency will be low c. low power will be obtained d. black smoke will be produced
Last Answer : ANSWER a. higher knocking will occur
Description : Mixing of air and fuel in the diesel engine occurs in a. injection pump b. carburetor c. engine cylinder d. inlet manifold
Last Answer : ANSWER c. engine cylinder
Description : The tendency of a diesel engine to knock increases if a. engine speed is increased b. engine power is increased c. cetane number of the fuel is increased d. compression ratio is increased
Last Answer : ANSWER d. compression ratio is increased
Description : Ignition quality of diesel is expressed by a. octane number b. cetane number c. calorific value d. carbon content
Last Answer : ANSWER b. cetane number
Description : For the best results of efficient combustion, high speed diesel engines need an approximate cetane number of a. 100 b. 50 c. 10 d. 5
Last Answer : ANSWER b. 50
Description : The specific gravity of diesel oil is a. 1 b. 0.85 c. 0.5 d. 0.7
Last Answer : ANSWER b. 0.85
Description : The self-ignition temperature of diesel oil compared to petrol is a. higher b. lower c. same d. depends on the quality of fuel
Last Answer : ANSWER a. higher
Description : Which of the following is the lightest and most volatile liquid fuel? a. diesel b. kerosene c. gasoline d. fuel oil
Last Answer : ANSWER c. gasoline
Description : The probability of knocking in diesel engines is increased by a. High self-ignition temperature. b. Low volatility. c. High viscosity. d. All of the above
Description : The term scavenging is generally associated with a. 2-stroke engine b. 4-stroke engine c. high efficiency engine d. diesel engine
Last Answer : ANSWER C. high efficiency engine