Furnace aerodynamics is related to the __________ in the furnace. (A) Movement of gases (B) Measurement of flue gas volume (C) Temperature control

Furnace aerodynamics is related to the __________ in the furnace.
(A) Movement of gases
(B) Measurement of flue gas volume
(C) Temperature control
by

1 Answer

Answer :

(A) Movement of gases
by

Related questions

The heat recoverable from flue gases of furnaces depends on the (A) Thermal efficiency of furnace (B) Quantity of flue gases (C) Flue gas temperature drop through the furnace (D) All (A), (B) and (C)

Description : The heat recoverable from flue gases of furnaces depends on the (A) Thermal efficiency of furnace (B) Quantity of flue gases (C) Flue gas temperature drop through the furnace (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick out the wrong statement. (A) A slight haze at the top of chimney indicates good combustion in the furnace (B) A bag filter incurs very small pressure drop and is very efficient for removal of submicronic dust particles from flue gases at very high temperature (C) Electrostatic precipitator is the most efficient dust collection equipment for removal of submicronic dust particles present in flue gas (D) None of these

Description : Pick out the wrong statement. (A) A slight haze at the top of chimney indicates good combustion in the furnace (B) A bag filter incurs very small pressure drop and is very efficient for ... dust collection equipment for removal of submicronic dust particles present in flue gas (D) None of these

Last Answer : (B) A bag filter incurs very small pressure drop and is very efficient for removal of submicronic dust particles from flue gases at very high temperature

Find false statement about effect of sulphur in fuel? (A) It has heating value (B) It helps in electrostatic precipitation of ash in flue gases (C) It leads to corrosion of air heaters, ducting, etc. if flue gas exit temperature is low (D) It erodes furnace walls

Description : Find false statement about effect of sulphur in fuel? (A) It has heating value (B) It helps in electrostatic precipitation of ash in flue gases (C) It leads to corrosion of air heaters, ducting, etc. if flue gas exit temperature is low (D) It erodes furnace walls

Last Answer : (D) It erodes furnace walls

Incomplete combustion of fuel in the furnace is judged by high __________ of the flue gases. (A) CO content (B) Dew point (C) CO2 content (D) O2 content

Description : Incomplete combustion of fuel in the furnace is judged by high __________ of the flue gases. (A) CO content (B) Dew point (C) CO2 content (D) O2 content

Last Answer : (A) CO content

Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Description : Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Last Answer : (B) Flame temperature

Flue gas outlet temperature from the chimney of any furnace should be ideally about __________ °C. (A) 50 (B) 100 (C) 150

Description : Flue gas outlet temperature from the chimney of any furnace should be ideally about __________ °C. (A) 50 (B) 100 (C) 150

Last Answer : (C) 150

Which of these is an output of a ‘Furnace’? a. Fuel gas b. Cool Air c. Flue gases d. Water Vapor

Description : Which of these is an output of a ‘Furnace’? a. Fuel gas b. Cool Air c. Flue gases d. Water Vapor

Last Answer : c. Flue gases

Which of the following is not an additive for flue gases from furnace to reduce its dew-point? (A) Ammonia (B) Fine dolomite (C) Alkaline powders (D) None of these

Description : Which of the following is not an additive for flue gases from furnace to reduce its dew-point? (A) Ammonia (B) Fine dolomite (C) Alkaline powders (D) None of these

Last Answer : (D) None of these

Which furnace employs an I.D. fan for the removal of flue gases from the furnace? (A) Coke oven(B) Blast furnace stoves(C) Beehive coke oven(D) High pressure boiler

Description : Which furnace employs an I.D. fan for the removal of flue gases from the furnace? (A) Coke oven (B) Blast furnace stoves (C) Beehive coke oven (D) High pressure boiler

Last Answer : (D) High pressure boiler

Which of the following is not a continuous waste heat recovery equipment from the flue gases going out of furnace? (A) Economiser (B) Regenerator (C) Ceramic recuperator (D) Waste heat boiler

Description : Which of the following is not a continuous waste heat recovery equipment from the flue gases going out of furnace? (A) Economiser (B) Regenerator (C) Ceramic recuperator (D) Waste heat boiler

Last Answer : (B) Regenerator

In a furnace, the heat taken by the charge/stock and the heat lost to the furnace structure & flue gases depends on the (A) Rate of firing and emissivity of flame (B) Thermal conductivity of the charge & structural materials of furnace (C) Nature of process; whether batch, continuous or intermittent (D) All (A), (B) and (C)

Description : In a furnace, the heat taken by the charge/stock and the heat lost to the furnace structure & flue gases depends on the (A) Rate of firing and emissivity of flame (B) Thermal conductivity of the charge & ... (C) Nature of process; whether batch, continuous or intermittent (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Most of the phosphorous present in the blast furnace burden enters into (A) Hot metal (B) Flue gases (C) Slag (D) Refractory lining

Description : Most of the phosphorous present in the blast furnace burden enters into (A) Hot metal (B) Flue gases (C) Slag (D) Refractory lining

Last Answer : (A) Hot metal

Oxygen percentage in the flue gas coming out of a gaseous fuel fired furnace should be ideally about __________ percent. (A) < 2 (B) < 5 (C) < 8 (D) < 10

Description : Oxygen percentage in the flue gas coming out of a gaseous fuel fired furnace should be ideally about __________ percent. (A) < 2 (B) < 5 (C) < 8 (D) < 10

Last Answer : (A) < 2

Scaling of furnace stock is reduced by __________ in flue gas. (A) CO (B) H2 (C) High CO/CO2 (D) All (A), (B) & (C)

Description : Scaling of furnace stock is reduced by __________ in flue gas. (A) CO (B) H2 (C) High CO/CO2 (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Flue gases coming out from furnace is first going through a) Turbine b) Economizer c) Air pre-heater d) Chimney

Description : Flue gases coming out from furnace is first going through a) Turbine b) Economizer c) Air pre-heater d) Chimney

Last Answer : Ans: Economizer

Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Description : Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Last Answer : (B) Oxygen in the flue gas

Out of the following fuels used in a furnace exhausting flue gas at a temperature of 600°C, the percentage stack loss will be maximum in case ofcomplete combustion of(A) Furnace oil with air(B) Furnace oil with oxygen(C) Blast furnace gas with air(D) Blast furnace gas with oxygen

Description : Out of the following fuels used in a furnace exhausting flue gas at a temperature of 600°C, the percentage stack loss will be maximum in case ofcomplete combustion of (A) Furnace oil with air (B) Furnace oil with oxygen (C) Blast furnace gas with air (D) Blast furnace gas with oxygen

Last Answer : (C) Blast furnace gas with air

Ingress of cold air in the furnaces through cracks, charging doors, openings etc(A) Reduces the flue gas temperature and makes the furnace atmosphereoxidising(B) Increases the load on the induced draft fan(C) Reduces the furnace draught(D) All (A), (B) and (C)

Description : Ingress of cold air in the furnaces through cracks, charging doors, openings etc (A) Reduces the flue gas temperature and makes the furnace atmosphere oxidising (B) Increases the load on the induced draft fan (C) Reduces the furnace draught (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Heat transfer rate to the charge/stock in a furnace does not depend upon the (A) Type of fuels viz. solid, liquid or gaseous (B) Flue gas temperature (C) Emissivity of refractory walls (D) Initial temperature of the charged stock

Description : Heat transfer rate to the charge/stock in a furnace does not depend upon the (A) Type of fuels viz. solid, liquid or gaseous (B) Flue gas temperature (C) Emissivity of refractory walls (D) Initial temperature of the charged stock

Last Answer : (A) Type of fuels viz. solid, liquid or gaseous

Air filtration in a furnace (A) Reduces its thermal efficiency (B) Is indicated by flame sting out (C) Increases the flue gas temperature (D) None of these

Description : Air filtration in a furnace (A) Reduces its thermal efficiency (B) Is indicated by flame sting out (C) Increases the flue gas temperature (D) None of these

Last Answer : (A) Reduces its thermal efficiency

Which of the following variables affects the furnace capacity? (A) Temperature of flue gas (B) Thermal conductivity of stock (C) Thickness of heating stock(D) All (A), (B) and (C)

Description : Which of the following variables affects the furnace capacity? (A) Temperature of flue gas (B) Thermal conductivity of stock (C) Thickness of heating stock (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Advantages of fluidised bed combustion are (A) Reduced NOx formation in flue gas (B) Lower furnace operating temperature (C) High heat transfer rate (D) All (A), (B) & (C)

Description : Advantages of fluidised bed combustion are (A) Reduced NOx formation in flue gas (B) Lower furnace operating temperature (C) High heat transfer rate (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Description : The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Last Answer : (B) Enhanced sensible heat loss in the flue gas

High sulphur content in a fuel __________ of the flue gases. (A) Decreases the dew point (B) Increases the dew point (C) Reduces the combustion efficiency by limiting the permissible temperature reduction (D) Both (B) and (C)

Description : High sulphur content in a fuel __________ of the flue gases. (A) Decreases the dew point (B) Increases the dew point (C) Reduces the combustion efficiency by limiting the permissible temperature reduction (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Description : Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Ringelmann chart is used for the measurement of the (A) Combustibles present in automobile exhaust (B) Smoke density from a chimney (C) Exhaust gas density (D) Flue gas temperature

Description : Ringelmann chart is used for the measurement of the (A) Combustibles present in automobile exhaust (B) Smoke density from a chimney (C) Exhaust gas density (D) Flue gas temperature

Last Answer : (B) Smoke density from a chimney

Circulation of gases in furnace is caused by the (A) Change in volume during a change of temperature (B) Difference in density between hot and cold gases (C) Furnace pressure in conjunction with draft in flues(D) All (A), (B) and (C

Description : Circulation of gases in furnace is caused by the (A) Change in volume during a change of temperature (B) Difference in density between hot and cold gases (C) Furnace pressure in conjunction with draft in flues (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid fuels (C) Imperfect mixing of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Description : In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid ... of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Last Answer : (C) Imperfect mixing of fuel & air and infiltration of air

Thermal efficiency of furnaces can be improved by (A) Waste heat recovery from flue gas (B) Minimising heat losses from furnace walls(C) Maintaining proper draught(D) All (A), (B) and (C

Description : Thermal efficiency of furnaces can be improved by (A) Waste heat recovery from flue gas (B) Minimising heat losses from furnace walls (C) Maintaining proper draught (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

In order to maintain an oxidising atmosphere in a furnace, it should have (A) More of excess air (B) Less of excess air (C) More of CO in flue gas (D) More of CO2 in flue gas

Description : In order to maintain an oxidising atmosphere in a furnace, it should have (A) More of excess air (B) Less of excess air (C) More of CO in flue gas (D) More of CO2 in flue gas

Last Answer : (A) More of excess air

Pitch creosote mixture (PCM) as compared to furnace oil is a better fuel, because its (A) Emissivity factor is higher (B) Sulphur content is lower (C) Flue gas has lower dew point thereby facilitating more waste heat recovery (D) All (A), (B) and (C)

Description : Pitch creosote mixture (PCM) as compared to furnace oil is a better fuel, because its (A) Emissivity factor is higher (B) Sulphur content is lower (C) Flue gas has lower dew point thereby facilitating more waste heat recovery (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

White flue gas (resembling steam) coming out of the chimney of a thermal power plant indicates that the fuel used in the boiler furnace is (A) Tar (B) Coke oven gas (C) Pitch (D) Pulverised coke

Description : White flue gas (resembling steam) coming out of the chimney of a thermal power plant indicates that the fuel used in the boiler furnace is (A) Tar (B) Coke oven gas (C) Pitch (D) Pulverised coke

Last Answer : (B) Coke oven gas

Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat of the substance): 0.20 kCal/kg oC DT (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Description : Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat ... (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Last Answer : 21600

The economiser is used in boilers to........ A]Increase thermal efficiency of boiler B]Economise on fuel C]Extract heat from the exhaust the gases D]Increase flue gas temperature

Description : The economiser is used in boilers to........ A]Increase thermal efficiency of boiler B]Economise on fuel C]Extract heat from the exhaust the gases D]Increase flue gas temperature

Last Answer : A]Increase thermal efficiency of boiler

To convert volumetric analysis to gravimetric analysis, the relative volume of each constituent of the flue gases is  (a) divided by its molecular weight  (b) multiplied by its molecular weight  (c) multiplied by its density  (d) multiplied by its specific weight  (e) divided by its specific weight.

Description : To convert volumetric analysis to gravimetric analysis, the relative volume of each constituent of the flue gases is  (a) divided by its molecular weight  (b) multiplied by its molecular weight  (c) ... by its density  (d) multiplied by its specific weight  (e) divided by its specific weight.

Last Answer : Answer : b

Limestone powder is injected during pulverised coal burning in boilers to __________ the flue gases. (A) Reduce SO2 content in (B) Catalytically convert SO2 to SO3 in (C) Increase the dew point of (D) None of these

Description : Limestone powder is injected during pulverised coal burning in boilers to __________ the flue gases. (A) Reduce SO2 content in (B) Catalytically convert SO2 to SO3 in (C) Increase the dew point of (D) None of these

Last Answer : (A) Reduce SO2 content in

Which among the following has the highest flue gas loss on combustion due to Hydrogen in the fuel? a) natural gas b) furnace oil c) coal d) light diesel oil

Description : Which among the following has the highest flue gas loss on combustion due to Hydrogen in the fuel? a) natural gas b) furnace oil c) coal d) light diesel oil

Last Answer : a) natural gas

Design of waste heat boiler for recovery of waste heat from furnace gases depends upon the(A) Quantity & temperature of waste gas(B) Dust concentration & nature of dust in waste gas(C) Corrosive nature of the waste gas(D) All (A), (B) and (C)

Description : Design of waste heat boiler for recovery of waste heat from furnace gases depends upon the (A) Quantity & temperature of waste gas (B) Dust concentration & nature of dust in waste gas (C) Corrosive nature of the waste gas (D) All (A), (B) and (C)

Last Answer : (B) Dust concentration & nature of dust in waste gas

Temperature of hot gases flowing in a pipe is measured by a thermocouple inserted in the thermal well. The thermal well made of __________ will facilitate the most accurate measurement of the temperature. (A) Copper (B) Steel (C) Aluminium (D) Brass

Description : Temperature of hot gases flowing in a pipe is measured by a thermocouple inserted in the thermal well. The thermal well made of __________ will facilitate the most accurate measurement of the temperature. (A) Copper (B) Steel (C) Aluminium (D) Brass

Last Answer : Option A

Temperature of hot gases flowing in a pipe is measured by a thermocouple inserted in the thermal well. The thermal well made of __________ will facilitate the most accurate measurement of the temperature. (A) Copper (B) Steel (C) Aluminium (D) Brass

Description : Temperature of hot gases flowing in a pipe is measured by a thermocouple inserted in the thermal well. The thermal well made of __________ will facilitate the most accurate measurement of the temperature. (A) Copper (B) Steel (C) Aluminium (D) Brass

Last Answer : Option A

Metallic recuperators are not used for waste heat recovery, if the hot flue gas temperature is above __________ °C, because corrosion prevails at higher temperatures. (A) 350 (B) 750 (C) 1050 (D) 1250

Description : Metallic recuperators are not used for waste heat recovery, if the hot flue gas temperature is above __________ °C, because corrosion prevails at higher temperatures. (A) 350 (B) 750 (C) 1050 (D) 1250

Last Answer : (B) 750

Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Description : Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Last Answer : (B) 130

Efficiency of the combustion of a fuel is judged by the __________ the flue gas. (A) % of CO2 in (B) % of O2 in (C) Temperature of (D) Colour of

Description : Efficiency of the combustion of a fuel is judged by the __________ the flue gas. (A) % of CO2 in (B) % of O2 in (C) Temperature of (D) Colour of

Last Answer : (B) % of O2 in

Incomplete combustion of a fuel is characterised by the high __________ in the flue gas. (A) Smoke (B) Temperature (C) Oxygen (D) Carbon monoxide

Description : Incomplete combustion of a fuel is characterised by the high __________ in the flue gas. (A) Smoke (B) Temperature (C) Oxygen (D) Carbon monoxide

Last Answer : (D) Carbon monoxide

The average molecular weight of a flue gas having the composition by volume as CO2 = 25%, O2 = 25%, N2 = 50% will be (A) 27.6 (B) 23 (C) 47.3 (D) 42.9

Description : The average molecular weight of a flue gas having the composition by volume as CO2 = 25%, O2 = 25%, N2 = 50% will be (A) 27.6 (B) 23 (C) 47.3 (D) 42.9

Last Answer : (B) 23

Sensible heat of hot industrial flue gases cannot be recovered by a/an (A) Economiser (B) Regenerator (C) Ceramic recuperator (D) None of these

Description : Sensible heat of hot industrial flue gases cannot be recovered by a/an (A) Economiser (B) Regenerator (C) Ceramic recuperator (D) None of these

Last Answer : (D) None of these

Waste heat from the outgoing flue gases in a thermal power plant is recovered by a/an (A) Economiser (B) Steam superheater (C) Air preheater (D) All (A), (B) and (C)

Description : Waste heat from the outgoing flue gases in a thermal power plant is recovered by a/an (A) Economiser (B) Steam superheater (C) Air preheater (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

With increase in C/H ratio of a fuel, the dew point of flue gases (A) Increases (B) Decreases (C) Remain same (D) May increase or decrease; depends on the type of fuel

Description : With increase in C/H ratio of a fuel, the dew point of flue gases (A) Increases (B) Decreases (C) Remain same (D) May increase or decrease; depends on the type of fuel

Last Answer : (B) Decreases

Which of the following accounts for maximum energy loss in a boiler? (A) Flue gases (B) Ash content in the fuel (C) Incomplete combustion (D) Unburnt carbon in flue gases

Description : Which of the following accounts for maximum energy loss in a boiler? (A) Flue gases (B) Ash content in the fuel (C) Incomplete combustion (D) Unburnt carbon in flue gases

Last Answer : (A) Flue gases