Advantages of fluidised bed combustion are (A) Reduced NOx formation in flue gas (B) Lower furnace operating temperature (C) High heat transfer rate (D) All (A), (B) & (C)

Advantages of fluidised bed combustion are
(A) Reduced NOx
formation in flue gas
(B) Lower furnace operating temperature
(C) High heat transfer rate
(D) All (A), (B) & (C)
by

1 Answer

Answer :

(D) All (A), (B) & (C)
by

Related questions

Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Description : Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Last Answer : (B) Oxygen in the flue gas

The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Description : The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Last Answer : (B) Enhanced sensible heat loss in the flue gas

Which of the following is not applicable to fluidised bed combustion of coal? (A) It cannot burn low grade coal (B) It achieves higher fuel combustion efficiency (C) Less heat transfer surface area is required in boilers (D) None of these

Description : Which of the following is not applicable to fluidised bed combustion of coal? (A) It cannot burn low grade coal (B) It achieves higher fuel combustion efficiency (C) Less heat transfer surface area is required in boilers (D) None of these

Last Answer : (A) It cannot burn low grade coal

Heat transfer rate to the charge/stock in a furnace does not depend upon the (A) Type of fuels viz. solid, liquid or gaseous (B) Flue gas temperature (C) Emissivity of refractory walls (D) Initial temperature of the charged stock

Description : Heat transfer rate to the charge/stock in a furnace does not depend upon the (A) Type of fuels viz. solid, liquid or gaseous (B) Flue gas temperature (C) Emissivity of refractory walls (D) Initial temperature of the charged stock

Last Answer : (A) Type of fuels viz. solid, liquid or gaseous

Pick out the wrong statement. (A) A slight haze at the top of chimney indicates good combustion in the furnace (B) A bag filter incurs very small pressure drop and is very efficient for removal of submicronic dust particles from flue gases at very high temperature (C) Electrostatic precipitator is the most efficient dust collection equipment for removal of submicronic dust particles present in flue gas (D) None of these

Description : Pick out the wrong statement. (A) A slight haze at the top of chimney indicates good combustion in the furnace (B) A bag filter incurs very small pressure drop and is very efficient for ... dust collection equipment for removal of submicronic dust particles present in flue gas (D) None of these

Last Answer : (B) A bag filter incurs very small pressure drop and is very efficient for removal of submicronic dust particles from flue gases at very high temperature

Scaling of furnace stock is reduced by __________ in flue gas. (A) CO (B) H2 (C) High CO/CO2 (D) All (A), (B) & (C)

Description : Scaling of furnace stock is reduced by __________ in flue gas. (A) CO (B) H2 (C) High CO/CO2 (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid fuels (C) Imperfect mixing of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Description : In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid ... of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Last Answer : (C) Imperfect mixing of fuel & air and infiltration of air

Out of the following fuels used in a furnace exhausting flue gas at a temperature of 600°C, the percentage stack loss will be maximum in case ofcomplete combustion of(A) Furnace oil with air(B) Furnace oil with oxygen(C) Blast furnace gas with air(D) Blast furnace gas with oxygen

Description : Out of the following fuels used in a furnace exhausting flue gas at a temperature of 600°C, the percentage stack loss will be maximum in case ofcomplete combustion of (A) Furnace oil with air (B) Furnace oil with oxygen (C) Blast furnace gas with air (D) Blast furnace gas with oxygen

Last Answer : (C) Blast furnace gas with air

Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Description : Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Last Answer : (B) Flame temperature

Heat transfer by __________ is almost absent in case of fluidised bed drying operation. (A) Radiation (B) Conduction (C) Convection (D) Both (B) & (C)

Description : Heat transfer by __________ is almost absent in case of fluidised bed drying operation. (A) Radiation (B) Conduction (C) Convection (D) Both (B) & (C)

Last Answer : A) Radiation

Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Description : Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Last Answer : (A) Calorific value of the fuel

Pitch creosote mixture (PCM) as compared to furnace oil is a better fuel, because its (A) Emissivity factor is higher (B) Sulphur content is lower (C) Flue gas has lower dew point thereby facilitating more waste heat recovery (D) All (A), (B) and (C)

Description : Pitch creosote mixture (PCM) as compared to furnace oil is a better fuel, because its (A) Emissivity factor is higher (B) Sulphur content is lower (C) Flue gas has lower dew point thereby facilitating more waste heat recovery (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Description : Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Incomplete combustion of fuel in the furnace is judged by high __________ of the flue gases. (A) CO content (B) Dew point (C) CO2 content (D) O2 content

Description : Incomplete combustion of fuel in the furnace is judged by high __________ of the flue gases. (A) CO content (B) Dew point (C) CO2 content (D) O2 content

Last Answer : (A) CO content

Low NOx Combustion Technology Regulation in Japan for Coal Firing Boiler has reduced from 400 ppm to____ a. 100ppm b. 200ppm c. 300ppm d. 400ppm

Description : Low NOx Combustion Technology Regulation in Japan for Coal Firing Boiler has reduced from 400 ppm to____ a. 100ppm b. 200ppm c. 300ppm d. 400ppm

Last Answer : Ans:- b. 200ppm

Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Description : Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Last Answer : (B) Keeping the flue gas exhaust temperature very high

In a furnace, the heat taken by the charge/stock and the heat lost to the furnace structure & flue gases depends on the (A) Rate of firing and emissivity of flame (B) Thermal conductivity of the charge & structural materials of furnace (C) Nature of process; whether batch, continuous or intermittent (D) All (A), (B) and (C)

Description : In a furnace, the heat taken by the charge/stock and the heat lost to the furnace structure & flue gases depends on the (A) Rate of firing and emissivity of flame (B) Thermal conductivity of the charge & ... (C) Nature of process; whether batch, continuous or intermittent (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which among the following has the highest flue gas loss on combustion due to Hydrogen in the fuel? a) natural gas b) furnace oil c) coal d) light diesel oil

Description : Which among the following has the highest flue gas loss on combustion due to Hydrogen in the fuel? a) natural gas b) furnace oil c) coal d) light diesel oil

Last Answer : a) natural gas

Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Description : Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature (C) Heat release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Description : Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature ... release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Presence of nitrogen in combustion air does not reduce the (A) Amount of heat liberated (B) Flame temperature (C) Flue gas temperature (D) Any of the above

Description : Presence of nitrogen in combustion air does not reduce the (A) Amount of heat liberated (B) Flame temperature (C) Flue gas temperature (D) Any of the above

Last Answer : (A) Amount of heat liberated

The heat recoverable from flue gases of furnaces depends on the (A) Thermal efficiency of furnace (B) Quantity of flue gases (C) Flue gas temperature drop through the furnace (D) All (A), (B) and (C)

Description : The heat recoverable from flue gases of furnaces depends on the (A) Thermal efficiency of furnace (B) Quantity of flue gases (C) Flue gas temperature drop through the furnace (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Description : Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Incomplete combustion of a fuel is characterised by the high __________ in the flue gas. (A) Smoke (B) Temperature (C) Oxygen (D) Carbon monoxide

Description : Incomplete combustion of a fuel is characterised by the high __________ in the flue gas. (A) Smoke (B) Temperature (C) Oxygen (D) Carbon monoxide

Last Answer : (D) Carbon monoxide

Steam is intermittently admitted into the fuel bed during the production of producer gas to (A) Convert CO to CO2 (B) Increase the combustion rate (C) Increase the gas production rate (D) Minimise the chances of clinker formation

Description : Steam is intermittently admitted into the fuel bed during the production of producer gas to (A) Convert CO to CO2 (B) Increase the combustion rate (C) Increase the gas production rate (D) Minimise the chances of clinker formation

Last Answer : (D) Minimise the chances of clinker formation

To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Description : To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Thermal efficiency of furnaces can be improved by (A) Waste heat recovery from flue gas (B) Minimising heat losses from furnace walls(C) Maintaining proper draught(D) All (A), (B) and (C

Description : Thermal efficiency of furnaces can be improved by (A) Waste heat recovery from flue gas (B) Minimising heat losses from furnace walls (C) Maintaining proper draught (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

Forced recirculation of furnace gases is practised (A) To increase heat transfer by convection (B) To ensure uniform temperature (C) In furnaces, operating below 750°C (D) All (A), (B) and (C)

Description : Forced recirculation of furnace gases is practised (A) To increase heat transfer by convection (B) To ensure uniform temperature (C) In furnaces, operating below 750°C (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Tar is a better fuel than furnace oil, because of its (A) Higher calorific value (B) Lower sulphur content (C) Higher emissivity (0.8-0.9) resulting in higher radiation heat transfer rate (D) Both (A) and (B)

Description : Tar is a better fuel than furnace oil, because of its (A) Higher calorific value (B) Lower sulphur content (C) Higher emissivity (0.8-0.9) resulting in higher radiation heat transfer rate (D) Both (A) and (B)

Last Answer : (D) Both (A) and (B)

Flue gas obtained on complete combustion of pure acetylene (a hydrocarbon fuel) will contain (A) CO (B) CO2 (C) H2O (D) Both (B) & (C)

Description : Flue gas obtained on complete combustion of pure acetylene (a hydrocarbon fuel) will contain (A) CO (B) CO2 (C) H2O (D) Both (B) & (C)

Last Answer : (D) Both (B) & (C)

Ostwald charts are meant for (A) Computing the excess/deficiency of combustion air (B) Calculation of flue gas temperature (C) Computation of flue gas analysis (D) None of these

Description : Ostwald charts are meant for (A) Computing the excess/deficiency of combustion air (B) Calculation of flue gas temperature (C) Computation of flue gas analysis (D) None of these

Last Answer : (A) Computing the excess/deficiency of combustion air

Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Description : Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Last Answer : (B) 130

Efficiency of the combustion of a fuel is judged by the __________ the flue gas. (A) % of CO2 in (B) % of O2 in (C) Temperature of (D) Colour of

Description : Efficiency of the combustion of a fuel is judged by the __________ the flue gas. (A) % of CO2 in (B) % of O2 in (C) Temperature of (D) Colour of

Last Answer : (B) % of O2 in

Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) Requirement of large volume combustion chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Description : Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) ... chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Last Answer : (B) Risk of explosion

Ingress of cold air in the furnaces through cracks, charging doors, openings etc(A) Reduces the flue gas temperature and makes the furnace atmosphereoxidising(B) Increases the load on the induced draft fan(C) Reduces the furnace draught(D) All (A), (B) and (C)

Description : Ingress of cold air in the furnaces through cracks, charging doors, openings etc (A) Reduces the flue gas temperature and makes the furnace atmosphere oxidising (B) Increases the load on the induced draft fan (C) Reduces the furnace draught (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Air filtration in a furnace (A) Reduces its thermal efficiency (B) Is indicated by flame sting out (C) Increases the flue gas temperature (D) None of these

Description : Air filtration in a furnace (A) Reduces its thermal efficiency (B) Is indicated by flame sting out (C) Increases the flue gas temperature (D) None of these

Last Answer : (A) Reduces its thermal efficiency

Furnace aerodynamics is related to the __________ in the furnace. (A) Movement of gases (B) Measurement of flue gas volume (C) Temperature control

Description : Furnace aerodynamics is related to the __________ in the furnace. (A) Movement of gases (B) Measurement of flue gas volume (C) Temperature control

Last Answer : (A) Movement of gases

Flue gas outlet temperature from the chimney of any furnace should be ideally about __________ °C. (A) 50 (B) 100 (C) 150

Description : Flue gas outlet temperature from the chimney of any furnace should be ideally about __________ °C. (A) 50 (B) 100 (C) 150

Last Answer : (C) 150

Which of the following variables affects the furnace capacity? (A) Temperature of flue gas (B) Thermal conductivity of stock (C) Thickness of heating stock(D) All (A), (B) and (C)

Description : Which of the following variables affects the furnace capacity? (A) Temperature of flue gas (B) Thermal conductivity of stock (C) Thickness of heating stock (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Economizer is provided to utilize the flue gas heat for ___ a) preheating the boiler feed water b) preheating the stock c) preheating the combustion air d) preheating fuel

Description : Economizer is provided to utilize the flue gas heat for ___ a) preheating the boiler feed water b) preheating the stock c) preheating the combustion air d) preheating fuel

Last Answer : preheating the boiler feed water

Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Description : Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Which of the following is the most suitable for very high pressure gas phase reaction? (A) Batch reactor (B) Tubular flow reactor (C) Stirred tank reactor (D) Fluidised bed reactor

Description : Which of the following is the most suitable for very high pressure gas phase reaction? (A) Batch reactor (B) Tubular flow reactor (C) Stirred tank reactor (D) Fluidised bed reactor

Last Answer : (B) Tubular flow reactor

Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Description : Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Last Answer : (A) Increase in calorific value of the fuel

In a fluidised bed reactor (A) Temperature gradients are very high (B) Temperature is more or less uniform (C) Hot spots are formed (D) Segregation of the solids occurs

Description : In a fluidised bed reactor (A) Temperature gradients are very high (B) Temperature is more or less uniform (C) Hot spots are formed (D) Segregation of the solids occurs

Last Answer : (B) Temperature is more or less uniform

Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to volatile matter percentage in coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Description : Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to ... coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Last Answer : (D) Calorific value of natural gas is more than that of LPG

If oxygen content in the flue gas rises too high, fuel is being wasted by (A) Incomplete combustion (B) Dry gas/stack gas loss (C) Moisture loss (D) None of these

Description : If oxygen content in the flue gas rises too high, fuel is being wasted by (A) Incomplete combustion (B) Dry gas/stack gas loss (C) Moisture loss (D) None of these

Last Answer : (B) Dry gas/stack gas loss

During combustion of a gaseous fuel, the presence of a non-luminous flame is an indication of the (A) Incomplete combustion (B) Complete combustion (C) High oxygen in flue gas (D) None of these

Description : During combustion of a gaseous fuel, the presence of a non-luminous flame is an indication of the (A) Incomplete combustion (B) Complete combustion (C) High oxygen in flue gas (D) None of these

Last Answer : (B) Complete combustion

When incomplete combustion loss is high, the flue gas analysis shows large amount of (A) CO2 (B) CO (C) O2 (D) C

Description : When incomplete combustion loss is high, the flue gas analysis shows large amount of (A) CO2 (B) CO (C) O2 (D) C

Last Answer : (B) CO

Volumetric composition of flue gas analysed with the Orsat apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas composition indicates that (A) Pure oxygen has been used for combustion (B) Nitrogen percentage in the fuel is very high (C) Excess air has been used for combustion (D) Hydrogen is not present in the fuel

Description : Volumetric composition of flue gas analysed with the Orsat apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas composition indicates that (A) Pure oxygen has been used for combustion ... very high (C) Excess air has been used for combustion (D) Hydrogen is not present in the fuel

Last Answer : (C) Excess air has been used for combustion