Draw full bridge & half bridge configuration with common cathode.

Draw full bridge & half bridge configuration with common cathode.
by

1 Answer

Answer :

Half Bridge Configuration:

image


Full Bridge Configuration: 

image

by

Related questions

Why common emitter configuration is commonly used?

Description : Why common emitter configuration is commonly used?

Last Answer : Common emitter configuration is commonly used for amplifications because 1. The common emitter configuration (CE) provides maximum voltage and current gain and hence provides maximum power gain. The ... automatic impedance matching maximum power transfer will take place from one stage to other.

Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Description : Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Last Answer : Single phase fully control bridge converter with RL load: 1. During positive half cycle of input voltage, T1 and T2 are forward biased and during negative half cycle, T3 and T4 are forward biased. Therefore, T1-T2 ... cycle till the firing of next pair of SCRs as shown in the waveform.

Explain full bridge converter.

Description : Explain the operation of full bridge converters with their different operating modes. State its advantages and disadvantages.

Last Answer : Full bridge converter: Full bridge converter provides isolation between input and output. Full bridge converter is used for step up or step down the input voltage. Full bridge converter consists of four power semiconductor ... Require filter on both input and output.

Draw circuit diagram of symmetrical configuration of bridge converter.

Description : Draw circuit diagram of symmetrical configuration of bridge converter.

Last Answer : circuit diagram of symmetrical configuration of bridge converter

Draw a neat diagram of 1Ф half wave controlled converter with RL load. Give its operation.

Description : Draw a neat diagram of 1Ф half wave controlled converter with RL load. Give its operation.

Last Answer : Single phase fully controlled half wave converter:  The circuit diagram of single-phase half-wave controlled rectifier with RL load and without freewheeling diode is shown in Fig. (a). The SCR T is ... , when again pulse is applied, the SCR is turned on & the above cycle is repeated. 

Which is the positive terminal anode or cathode?

Description : Which is the positive terminal anode or cathode?

Last Answer : Anode is positive terminal and cathode is negative terminal.

What is Cathode ray tube ?

Description : What is Cathode ray tube ?

Last Answer : Cathode ray tube (CRT) is a vacuum tube using cathode rays to generate a picture on a fluorescent screen. These cathode rays are in fact the electron beam deflected and modulated, which impinges on a ... tube used to display data in a visual form. Picture tube of a television or computer terminal.

Explain MOSFET gate drive circuit and totem pole configuration.

Description : Explain MOSFET gate drive circuit and totem pole configuration.

Last Answer : MOSFET gate drive circuit: The turning on and turning off of MOSFET can be controlled from gate to source voltage signal. If the gate to source voltage of MOSFET exceeds threshold ... this configuration, the two switches (transistors) are used in totem pole arrangement with a comparator.

Explain three phase half wave controller or three phase unidirectional controller.

Description : Explain three phase half wave controller or three phase unidirectional controller.

Last Answer : Three phase half wave controller or unidirectional controller:

Draw O/P characteristics of CB configuration and explain its working.

Description : Draw O/P characteristics of CB configuration and explain its working.

Last Answer : In common base configuration, emitter is the input terminal, collector is the output terminal and base terminal is connected as a common terminal for both input and output. The base-emitter ... In this region, a small collector current flows called leakage current when emitter current is zero.

Compare between CB , CE & CC transistor configuration.

Description : Compare between CB , CE & CC transistor configuration.

Last Answer : Parameter CB CE CC I/P impedance Low Or 50Ω Medium Or 600Ωto 4kΩ High Or 1 MΩ Current Gain Less than or equal to 1 High Highest Voltage Gain Medium Medium Less ... k Ω to 50 k Ω Low Or 50 Ω Phase shift between input and output 0° 360° 0° 

The ac bypassing of RF by CF in a common emitter configuration :

Description : The ac bypassing of RF by CF in a common emitter configuration :  (A) increases ac signal across emitter -base junction (B) decreases ac signal across emitter -base junction (C) decreases voltage amplification (D) stabilizes the Q -point

Last Answer : The ac bypassing of RF by CF in a common emitter configuration : increases ac signal across emitter -base junction

A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc

Description : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is (A) 4.5 V (B) 6.75 V (C) 9 V (D) 13.5 V

Last Answer : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is 9 V

The time base signal in Cathode Ray Oscilloscope (CRO) is

Description : The time base signal in Cathode Ray Oscilloscope (CRO) is  (1) A square wave signal (2) A sawtooth signal (3) A triangular wave signal (4) A sinusoidal signal

Last Answer : 2 Saw tooth 

Which of the following is a cold cathode lamp ?

Description : Which of the following is a cold cathode lamp ?  (A) Mercury vapour lamp (C) Incandescent lamp (B) Sodium vapour lamp (D) Neon lamp

Last Answer : Which of the following is a cold cathode lamp ?  (A) Mercury vapour lamp (C) Incandescent lamp (B) Sodium vapour lamp (D) Neon lamp

What is the difference between an anode and a cathode?

Description : What is the difference between an anode and a cathode?

Last Answer : The anode is positively charged electrode and the cathode is negatively charged electrode.

Do electrons flow from the anode to the cathode?

Description : Do electrons flow from the anode to the cathode?

Last Answer : electrons flow from cathode to anode because the electron has a negative charge and repels from the negatively charged cathode whilst also attracting to the positively charged anode.

Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it.

Description : Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it. 

Last Answer : Circuit Diagram: Waveforms:

In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load,

Description : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

Last Answer : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is alternating rectangular pulses

Explain three phase bridge inverter.

Description : Explain three phase bridge inverter.

Last Answer : Three phase bridge inverter: Three phase bridge inverter converts DC voltage input to three-phase variable frequency variable voltage output. DC voltage source can be a DC source or output of the rectifier. ... in proper sequence. The switch may be thyristor or IGBT etc.

explain blanking times for Bridge circuit?

Description : explain blanking times for Bridge circuit?

Last Answer : Blanking time is provided by driver circuit to power switch. Blanking time is important because the turn on input of one transistor must be delayed with turn off input of another transistor if both ... are connected in one converter leg. This blanking time helps in avoiding cross conduction.

Sketch output characteristics of CE configuration. Show all the regions.

Description : Sketch output characteristics of CE configuration. Show all the regions.

Last Answer : Sketch output characteristics of CE configuration. Show all the regions.

Which configuration has the lowest current gain ?

Description : Which configuration has the lowest current gain ?

Last Answer : Common base configuration has the lowest current gain.

How to Do a Half Nelson ?

Description : How to Do a Half Nelson ?

Last Answer : How to Do a Half Nelson In amateur and professional wrestling, the half-nelson is a basic maneuver that is known for its versatility and effectiveness. The half-nelson is a good move to use on its own, ... be a very basic maneuver can become one of the most effective holds you can use on the mat.

operation of half wave rectifier type AC Voltmeter.

Description : operation of half wave rectifier type AC Voltmeter.

Last Answer :  Half-wave Rectifier Voltmeter The d'Arsonval meter movement only responds to the average or dc value of the current through the moving coil. In order to measure alternating ... ) input voltage signal alternating signal needs to be rectified first by using diode rectifier to produce 

A four -quadrant operation requires two full converters connected in

Description : A four -quadrant operation requires two full converters connected in  (1) Series (3) Back to back (2) Parallel (4) Series Cascade

Last Answer : A four-quadrant operation requires two full converters connected in Parallel 

Why the power factor of semiconverter is better than full converter?

Description : Why the power factor of semiconverter is better than full converter?

Last Answer : Power factor of semiconverter is better than full converter

Explain three phase full wave controller.

Description : Explain three phase full wave controller.

Last Answer : Three phase full wave controller: Three phase full wave controller is also called as the three-phase bidirectional controller. Let the load is star connected so at each phase there are antiparallel connected SCRs. ... conduct at the same time and the third phase will be open.

single phase full converter

Description : single phase full converter

Last Answer : single phase full converter

How to Stop a Common Cold

Description : How to Stop a Common Cold

Last Answer : How to Stop a Common Cold The common cold hits all of us, and the worst part about having a cold is knowing that, while you can treat it, there is no miracle cure and you will probably catch a ... seven day, or if you develop a fever of more than one hundred degrees, go to the doctor immediately.

six most common multiples

Description : six most common multiples

Last Answer : six most common multiples

If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be

Description :  If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be A) 0.98 B) 0.41 C) 59 D) 55  

Last Answer :  If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be 0.98 

Which is the most common type of fault?

Description : Which is the most common type of fault?

Last Answer : Single phase to ground fault is the most common type of fault.

What is the most common type of power plant?

Description : What is the most common type of power plant?

Last Answer : Hydroelectric  power  plant.

How to Build a Bridge

Description : How to Build a Bridge

Last Answer : How to Build a Bridge How to Build a Bridge Building a bridge is not an every day task, you do not see bridges going up overnight and it takes a skilled engineer to master this craft. Bridges ... this can be one of the most satisfying moments of your life to know that you have achieved your goal.

How to Become a Bridge Inspector

Description : How to Become a Bridge Inspector

Last Answer : How to Become a Bridge Inspector Bridge Inspectors are construction professionals who are well versed in a number of building disciplines. Among the talents of a bridge inspector are such ... secure employment in a variety of different settings, both in government agencies and private business.

How to Become a Bridge Engineer

Description : How to Become a Bridge Engineer

Last Answer : How to Become a Bridge Engineer Bridge Engineers are construction professionals that bear a major part of the responsibility for the safety and stability of bridges. Consequently, a bridge engineer ... new business. A well-established reputation is vital to the success of bridge engineering career.

List out advantages and disadvantages of bridge rectifier.

Description : List out advantages and disadvantages of bridge rectifier.

Last Answer : Advantages :  1. Bridge rectifier can be used in applications allowing floating output terminals i.e. not output terminal is grounded.  2. The need of center-tapped transformer is eliminated.  ... The value of the diodes used should be precise , else there will be an error in rectification

operation of whetstone bridge.

Description :  operation of whetstone bridge. 

Last Answer : A Wheatstone bridge is widely used to measure the electrical resistance. This circuit is built with two known resistors, one unknown resistor and one variable resistor connected in the form of bridge. ... using a Wheatstone Bridge the unknown electrical resistance value can easily measure.

tern null as it applies to bridge measurement.

Description : tern null as it applies to bridge measurement.

Last Answer : Null measurements balance voltages so that there is no current flowing through the measuring device and, therefore, no alteration of the circuit being measured. Null measurements are generally more ... the use of standard voltmeters and ammeters, and they still have limits to their precision.

Wheatstone bridge

Description : Wheatstone bridge

Last Answer : Wheatstone bridge

A dummy strain gage is used in a quarter bridge strain gage circuit to :

Description : A dummy strain gage is used in a quarter bridge strain gage circuit to :  (A) compensate for changes in temperature and lead wire resistance  (B) produce more output voltage from the bridge  (C) increase the sensitivity of the bridge  (D) compensate lead wire resistance only

Last Answer : A dummy strain gage is used in a quarter bridge strain gage circuit to : compensate for changes in temperature and lead wire resistance 

Which of the following is true with respect to Wien Bridge?

Description : Which of the following is true with respect to Wien Bridge? A) It does not require equal values of R or C  B) It requires that R and C values of all components must be equal C) It requires that all resistors should have equal values D) None of these

Last Answer : Which of the following is true with respect to Wien Bridge? A) It does not require equal values of R or C  B) It requires that R and C values of all components must be equal C) It requires that all resistors should have equal values D) None of these

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a

Description : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) ... proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

Last Answer : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ directly proportional to α and inversely proportional to Φ

The bridge most suited for accurate measurement of relative permittivity of dielectric materials is

Description : The bridge most suited for accurate measurement of relative permittivity of dielectric materials is (A) Carey Foster Bridge (B) Anderson’s bridge (C) Heaviside Bridge modified by Campbell. (D) Schering Bridge.

Last Answer : The bridge most suited for accurate measurement of relative permittivity of dielectric materials is Schering Bridge.

The bridge method commonly used for finding mutual inductance is

Description : The bridge method commonly used for finding mutual inductance is (A) Heaviside Campbell bridge (B) Schering bridge (C) De Sauty bridge (D) Wien bridge

Last Answer : The bridge method commonly used for finding mutual inductance is Heaviside Campbell bridge

The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm

Description : The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

Last Answer : The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

If an inductance is connected in one arm of bridge and resistances in the remaining three arms?

Last Answer : If an inductance is connected in one arm of bridge and resistances in the remaining three arms the bridge cannot be balanced.

In a Schering bridge the potential of the detector above earth potential is?

Last Answer : In a Schering bridge the potential of the detector above earth potential is a few volts only.

In an Anderson bridge, the unknown inductance is measured in terms of?

Last Answer : In an Anderson bridge, the unknown inductance is measured in terms of known capacitance and resistance.